ignition AUDI S6 2012 User Guide

36 Opening and clo sing
- Rear doors : pu ll the door handle once to re­
l ease the lock. Pull the handle
again to open
the door .
- If you have a crash and the airbag is activat­
ed, the doors automatically un lock .
A WARNING
-The power locking switch works with the
ignition off and automatically locks the
entire vehicle whe n it is actuated .
- On a vehicle locked from the outside the
power locking system switch is inopera­
t ive .
- Locking doors from the inside can help
prevent inadvertent door opening during
an acc ident and ca n also prevent unwa nt­
ed entry from the outs id e. Locked doors
can, however, de lay ass istance to ve hicle
o ccupants and hold up res cue efforts
from the o utside in an a ccident or other
emergency.
(D Tips
Your vehicle is locked automatically at a
speed of 9 mph (15 km/h)
Q page 32 . You
can unlo ck the vehicle again us ing the
open ing f unct ion in the power lock ing sys ­
tem switch.
Emergency locking
Each door must be locked separately if the
pow er locking system fails.
Fig . 2 4 Doo r: Em erge ncy loc king
An emergency lock is located on the f ront end
of the passenger's door and the rear doors (on ly visible when door is open) .
.. Remove the mechanical key
Q page 31 .
.. Pull the cover cap out of the opening
~fig . 24 .
.. Insert the key in the ins ide slot and turn it
all the way to the right (right door) or left
(left door) .
Once the door has been closed, it can no lon­
ger be opened from the outside. The doo r can
be opened from the inside by pulling the door
handle. If the child safety lock in a rear door is
activated, you must f irst pu ll the door handle
on the inside . Then you ca n ope n the doo r
from t he outside .
Rear lid
Opening and closing rear lid
Fig. 25 Drive r's doo r: remote rear lid re lea se
Fi g. 2 6 Posit io n of h an dl e in th e r ear l id
Opening the rear lid
.. Press the midd le butto n~ on th e remote
cont ro l maste r key for at least one second,
o r
.. Pull the re lease but to n
l= I in the driver's
door
Q fig. 25, o r
.. Press t he handle on the rear lid
~ fig. 26.

38 Openin g and clo sing
- The power windows in the rear doors,
- The interior l ighting buttons.
In order to activate the child safety lock on
the left and the right side, press the two safe­
ty buttons [!l in succession.
Power windows
Controls
The driver can control all power windows .
Fig. 29 Section of the driver's door: Controls
All power window switches are provided with
a tw o-p osition fun ction :
Opening th e window s
• Press the switch to the
firs t stop and hold it
until the window reaches the desired posi­
tion.
• Press the switch br iefly to the
se cond stop
to automatically open the window .
Cl os in g th e window s
• Pull the switch to the
firs t s top and hold it
until the window reaches the des ired pos i­
tion.
• Pull the switch briefly to the
sec on d sto p to
automatically close the window .
P ow er wi ndow switche s
@ Driver's door
® Passenger's door
© Left rear door
® R ight rear door
A WARNING
- When you leave your veh icle -even if on­
ly briefly -always take the ignition key with you. This applies particularly when
children remain in the vehicle. Otherwise
the children could start the engine or op­
erate electrical equipment (e.g. power
windows). The power windows are func­
tional unt il the driver's door or passeng­
er's door has been opened.
- Be careful when clos ing the windows .
Check to see that no one is in the way, or
serio us inju ry cou ld result!
- When locking the vehicle from outside,
the vehicle must be unoccupied since the windows can no longer be opened in an
emergency.
(0 Tips
Afte r the ignition has been switched off,
the w indows can still be opened o r closed
fo r abo ut 10 minutes. The power windows
are not switched off until the driver's door
or passenger's door has been opened.
What to do after a malfunction
The one-touch open and close function must
be reactivated if the battery has been discon­
nected.
• Pull and ho ld the power window sw itch un­
til the w indow is f ully closed.
• Release the sw itch and then pull it again for
at least one second .
Valet parking
The valet parking feature protects the lug­
gage compartment from unauthorized ac­
cess.
F ig. 30 Luggage compartment: valet park ing button

Clear vision Lights
Switching the headlights on and off
Fig . 32 Instrument pane l: lig ht sw itc h wit h all -weath­
er lights•
The headlights only wo rk when the ignition is
switched on. Wh ile start ing the eng ine o r
when switching off the ign ition, the head­
lights will go off and on ly the side marker
lights will be on .
If the system is not operating p rope rly, a
war ning symbol in the dr iver information dis­
p lay is d isplayed
c::> page 22 .
Light switch ·'t!- -
Tu rn the switch c::> fig . 32 to the correspond ing
position . When the lights a re switched on, the
:oo: symbo l tu rns on .
0 -The lig hts are off or the dayt ime runn ing
lights are on:
- USA models: The daytime running ligh ts
will come on automatically when the igni­
t ion is on and the light switch
c::> fig . 32 is in
the O posit ion or the AUTO position (only in
daylight cond itions). The Daytime running
light s function can be turned on and off in
the MMI
c::> page42, c::>A .
-Ca nada model s: The daytime running lig hts
will come on automa tically when the igni­
t ion is on and the light switch
c::> fig . 32 is in
the O position, the
:oo: pos ition or the AUTO
position (only in daylight conditions)
c::> A .
AUTO -Automatic headlights swi tch on and
off depend ing o n brightness, for example i n
tw ilight, during rain or in tunnels
c::> &. .
:oo: -Side marke r lights
io -Low beam headlights
~ -All-weather lig hts*
Clear vi sion 41
[Q!l -Rear fog lights* . When th e rear fog lights
a re on, the symbol
0$ on the switch will illu­
mina te.
All-weath er lights*
In vehicles with all-weather lights, the front
li ghts are adj usted automatically so that you
are less like ly to see glare from your own
headligh ts, for example when driving on a wet
road .
Automatic headlight range cont rol*
The head lights do not blind oncoming traffic
if the vehicle load changes . The headlight
range also ad justs automatica lly when brak­
i ng and accelerat ing .
Light function s
T he following light funct ions are avai lab le de­
pending on vehicle equipment and on ly func­
tion when the light switch is i n the AUTO posi­
tion. You c an deactiv ate these functions in the
MMI under Audi adaptive light
c::> page 42 .
Vehicles w ith Static cornering light* : the cor­
ner ing light sw itches on automatica lly when
the stee ring whee l is tu rned at a ce rta in angle
at speeds up to approx imately 44 mph (70
km/ h) and when the turn signa l is ac tiva ted a t
speeds up to approximately 25 mph (40 km/
h) . The area to the s ide of the vehicle is illumi­
nated bette r whe n turn ing .
Vehicles with Dynamic curve light* : the
curve
li ght only functions at speeds betwee n ap ­
proximately 6 mph (10 km/h) and 68 mph
(110 km/ h) and adapts itself to the cu rves in
the ro ad.
_& WARNING
- Autom atic headlig hts are only intended
to assist the driver. They do not relieve
the dr iver of his responsibility to check
the head lights and to turn them on man -
ually accord ing to the current light and
~

42 Clear vision
visibility conditions. For example, fog cannot be detected by the light sensors.
So always switch on the headlights
io
under these weather conditions and
when driving in the dark.
- Crashes can happen when you cannot see
the road ahead and when you cannot be
seen by other motorists . Always turn on
the headlights so that you can see ahead and so that others can see your car from
the back.
(D Note
The rear fog lights should only be turned
on in accordance with traffic regulation, as
the lights are bright for following traffic.
@ Tips
-In the event of a light sensor malfunc­
tion, the driver is notified in the instru­
ment cluster display~
page 22.
- You will hear a warning tone if you open
the driver door when the exterior lights
are switched on.
- Please observe legal regulations when
using the lighting systems described .
Emergency flasher
The emergency flasher makes other motorists
aware that you or your vehicle are in an emer­
gency situation.
Fig. 33 Center console : emerge ncy flasher switch
• Press the switch~~ fig. 33 to turn the
emergency flashers on or off.
When the emergency flasher is on, all four
turn signals blink at the same time. The turn signal
indicato r lights ¢ Q in the instrument
cluster, as well as the light in the emergency
fl asher switch ~ blink likewise. The emergen­
cy flashers also work when the ignition is
turned off.
The emergency flashers will turn on automati­
cally if you are in an accident where the airbag
has deployed .
(D Tips
You should turn on the emergency flashers
when:
- you are the last vehicle standing in a traf­
fic jam so that any other vehicles coming
can see you, or when
- your vehicle has broken down or you are
in an emergency situation, or when
- your vehicle is being towed by a tow
truck or if you are towing another vehicle
behind you.
· Adjusting the exterior lighting
The settings ore adjusted in the MMI.
• Select: I CAR I function button > Car systems
control button > Vehicle settings> Exterior
lighting.
Automatic headlights
You can adjust the following settings in the
Automatic headlights menu :
Headlights activation time -You can adjust if
the headlights switch on
Early , Med. or Late
according to the sensitivity of the light sensor .
Audi adaptive light* -You can switch adaptive
light
On and Off .
Daytime running lights
USA models:
You can switch the daytime run­
ning lights
on and off.
Canada models:
The function cannot be
turned off.
It is activated automatically each
time the ignition is switched on. This menu
item is shown "greyed out".

Coming home , Leav ing home
The coming home function il luminates the
area outside the vehicle when you switch the
ignition off and open the driver 's door . To turn
the function on, select
Light s when le aving
c a r > On .
The leav ing home function illuminates the
area outside the vehicle when yo u un lock the
veh icle . To turn the function on, select
Li gh ts
when unloc kin g ca r> On.
The coming home and leaving home functions
only operate when it is dark and the light
switch is in the
AUTO pos ition.
Turn signals and high beam lever
The lever on the le~ side of the steering col­
umn is used to operate the turn signals and
the high beam as well as the headlight flash­
er .
Fig. 3 4 Tu rn signal a nd h igh beam lever
The turn s ignal and high beam lever has the
followi ng functions:
Tu rn sign als ¢ ¢ @@
.. Push the lever up as far as it can go to turn
on the r ight turn signal or down to turn on
the left turn sig nal
c:::;, fig . 34 .
.. Move the lever b riefly until you meet resist­
ance and release it to flash three times .
.. Move the lever (up or down) unti l you mee t
resistance and ho ld it there to dete rmine
the f las hing t ime for the turn signals.
High beam [D @
.. Push the lever forward to switch on the high
beam.
Clear vi sion 43
.. Pull the lever back towards you to switch off
the high beam.
Headlight fla sher [D ©
.. Pull the lever towa rd the stee ring wheel to
use the headlight flasher.
Note s on these features
- The turn signals on ly work with the ignition
sw itched on . The indicator lights
f,j or II in
the inst rument cluster~
page 12 also blink.
- After you have turned a corner, the turn s ig -
nal switches off automatically .
- The
high beam works only when the head ­
lights are on . The indicator light
Ill in the
instrument cluster illuminates when the
h igh beams are on.
- The
headlight flasher works only as long as
you hold the lever -even if the re a re no
lights turned on. The indicator light
Ill in
the inst rument cluster i lluminates whe n you
use the headlight flasher.
(D Note
Do no t use the high beam or headligh t
flasher if yo u know that these could blind
oncoming traffic.

44 Clear vis ion
Interior lights
Front and rear interior lighting
Fig. 35 Head liner: Fron t int eri or ligh ts
Fig. 36 Rear headlin er: R ead in g light
Press the appropriate b utton ~ fig. 35:
El -Interior lighting on/off
[j) -Door contact switch . The inter io r l ight ing
turns on automatically when you unlock the
vehi cle, open a doo r or switch the ignition off .
The interior lighting turns off several seconds
after you close the doors , when you lock the
vehicle or when you switch the ignition on.
When a door is open, the light t urns off after
a few minutes.
51 -Reading lights o n/off
~ -Sw itch ing the rear readi ng lights on/off
from the co ckpit.
I .,.. REAR !* -Switch ing the rear reading lights
on/off from the cockp it .
Ambience lighting
Appl ies to vehicles: wit h ambience lighting
You can adj ust the brightness for the amb i­
ence lighting. .,.
Select in the MM I: ICARlfunction button>
C ar sys tem s control button > Vehicle set­
ting s
> Interio r light ing > Brightne ss .
.,. To increase or reduce the brightness, turn
the knob and press it .
T he ambience lighting turns on when you turn
the headlights on while the ignition is switch­ ed on.
@ Tips
The setting is automatically stored and as­
signed to the remote control key that is in
use.
Instrument illumination
You can adjust the brightness of the instru ­
ment and display illumination as well as the
Head-up Display *.
F ig. 37 In strume nt ill umin ation
.,. Press the knob to re lease it .
~ 0 <? C) ..
"'
.,. Tur n the knob toward "-" or"+" to redu ce or
increase the br ightness.
.,. Press the knob aga in to retu rn it to its origi ­
na l position .
(I} Tips
The instrumen t illum ina tion (for dials and
needles) lights on when the ignition is
switc hed o n and the vehicle lights are
turned off . As the daylight fades, the illu ­
mination of the dia ls likewise d ims auto­
matically and will g o out completely when
the outs ide light is very low. This feature is
meant to rem ind yo u to sw itch on the
headlights when outsid e light conditions
be come poo r.

46 Clear vis ion
Wiper and washer
system
Switching the windshield wipers on
F ig. 4 1 Windsh ie ld wipe r lever
Move the windshield wiper lever to the corre­
spond ing pos ition:
@ -Windshie ld wipers off
(I) -Rain sensor mode . The windshield w ipers
switch on once the vehicle speed exceeds ap­
proximately 2 mph (4 km/h) and it is raining.
The higher the rain sensor sens it ivity is se t
(switch @to the right), the earlier the wind ­
shield wipers react to moisture on the wi nd­
shie ld. You can deact ivate rain sensor mode in
the MMI, which w ill then activate intermi ttent
mode. Selec t:
ICAR I function bu tton > C ar s ys­
t e m s
contro l bu tton > Dri ver a ssis t > Rain
se nsor
> Off . In intermittent mode, you can
adjust the interval time using the switch @.
@-Slow wiping
@-Fast wiping
©-Single wipe. If you hold the lever in this
posi tion longer, the wipers sw itch from slow
wiping to fast wip ing .
® - Clean the windshield . The wipers wipe
one time after several seconds of driv ing to
remove water drop le ts. You can switch this
function off by mov ing the lever to position ®
within 10 seconds after the afterw ipe . The af­
terw ipe fun ct ion is react ivated the next time
you swit ch the ig nitio n on .
Clean ing the headlights . The headlight wash ­
e r system* only functions when the lights are
switched on . The headlights and the night vi- s
ion system camera * are cleaned automatical ­
ly the first time the lever is press in position
® and every 8 times it is pressed after that.
They a re also cleaned every time you ho ld the
lever in posit ion ® for longer than 8 seconds.
A WARNING
--The rain sensor is only designed to assist
and support the dr iver .
It rema ins enti re­
ly the d river's responsibility to monitor
outs ide weather cond itions and to ma n­
u a lly activate the wipe rs as soon as rai n
or drizzle reduces visibility through the
windshie ld .
- The windsh ield mu st not b e tre ate d w ith
water -repellent materials . They can in ­
crease glare under poor v isibility condi­
tions such as wetness, da rkness, or when
the sun is low on the hor izon. In addi­
tion , they can cause the w indshield w ip­
ers to chatter.
- Properly function ing windsh ield wiper
b lades are req uired for a clea r view and
safe driving
i::> page 47, Replacing
windshield wiper blades.
(D Note
- In the case of frost, check whether the
w indshield wiper blades are fr ozen to
the windsh ield . Sw itching on the wind ­
shield wipers can damage the wiper blades!
- Pr ior to us ing a car wash, the w indshield
w iper system must be sw itched off ( lever
in posit ion 0). This he lps to prevent un in­
t en tional switch ing o n and dam age to
t he winds hield wiper system.
- Do not use the w ipers to clear a frosted
w indow. Us ing the wipers as a conve n­
ient ice scraper will destroy the wiper
blades.
(D Tips
- T he windshie ld wipers are sw itched off
w hen the ig nit io n is off . Activate the
windshield wipers after the ignition is
switched back o n by moving the w ind­
shield wiper lever to any position.

-Worn or dirty windshield wiper blades
result in streaking. This can affect the
rain sensor function. Check your wind­
shield wiper blades regularly .
- The washer fluid nozzles of the wind­
shield washer system are heated at low
temperatures when the ignition is on.
- When stopping temporarily, e.g. at a
traffic light, the set speed of the wind­
shield wipers is automatically reduced by
one speed .
Replacing windshield wiper blades
Wiper blades in good condition help keep the
windshield clear.
Fig. 42 Removing winds hie ld w iper bla des
Service position
• Switch the windshield wipers
off (position
@ ¢page 46, fig. 41).
• Switch the ignition off and move the wind­
shield wiper lever to position @¢
page 46 ,
fig. 41.
Or
• Select in the MMI: !CAR !function button>
Car systems control button > Servicing &
checks > Wiper service position > On. The
windshield wipers move into the service po­
sition.
Removing the wiper blade
• Fold the windshield wiper arm away from
the windshield.
• Press the locking knob@¢
fig. 42 on the
wiper blade . Hold the wiper blade firmly.
• Remove the wiper blade in the direction of
the arrow.
Clear vision 4 7
Installing the wiper blade
• Insert the new wiper blade into the mount
on the wiper arm @unti l you hear it latch
into place.
• Place the wiper arm back on the windshield.
• Switch the ignition on.
• Press the windshield wiper lever.
Or • Select:
I CAR ! function button > Car systems
control button > Servicing & checks > Wiper
service position
> Off.
.&_ WARNING
- If the windshield wipers smear the wind­
shield, clean the wiper blades with wind­
shield washer fluid. If the wiper blades
are extremely dirty, you can also clean
them with a soft sponge or cloth.
- For your safety, you should replace the
wiper blades once or twice a year. See
your authorized Audi dealer for replace­
ment blades.
(D Note
-The windshie ld wiper blades must only
be folded away when in the service posi­
tion! Otherwise, you risk damaging the
paint on the hood or the windshie ld wip­
er motor.
- You should not move your vehicle or
press the windshield wiper lever when
the wiper arms are folded away from the
windshield. The windshield wipers would move back into their original position
and could damage the hood and wind­
shield .
- To help prevent damage to the wiper sys­
tem, always loosen blades which are fro­
zen to the windshield before operating
w ipers.
- To help prevent damage to wiper blades,
do not use gasoline, kerosene, paint
thinner, or other solvents on or near the
wiper blades .
- To help prevent damage to the wiper
arms or other components, do not at­
tempt to move the wipe rs by hand.

Front passenger's seat
Always move the front passenger seat into the rearmost position.
To avoid contact with the airbag while it is de­
ploying, do not sit any closer to the instru­
ment panel than necessary and always wear
the three-point safety belt provided adjusted
correctly. We recommend that you adjust the
passenger's seat in the following manner:
.. Move the front passenger seat into the rear­
most position of the fore and aft adjustment
range
~ .&. in Why is your seat adjustment
so important? on page 50.
• Bring the backrest up to an (almost) upright
position.
Do not ride with the seat reclined .
.. Adjust the head restraint so the upper edge
is as even as possible with the top of your
head. If that is not possible, try to adjust
the head restraint so that it is as close to
th is position as possible ¢
page 52.
.. Place your feet on the floor in front of the
passenger's seat .
Front seats
Controls
The operating logic for the switches corre­
sponds to the construction and function of
the seat.
Fig. 45 Front seat: adjusting the seat
@ -adjusting lumbar support*: press the but­
ton in the corresponding position¢.&,.
@ -Moving the seat forward/back: press the
button forward/back ¢ ,&. .
@ -Mov ing the seat up/down: press the but­
ton up/down ¢,&. . To adjust the front section
Seats and storage 51
of the seat, press the front button up/down
¢ ,&. .To adjust the rear section of the seat,
press the rear button up/down ¢,&. .
© -Backrest forward/back: press the button
forward/back
~ ,&. .
A WARNING
-
-Never adjust the driver's or front pas­
senger's seat whi le the vehicle is moving.
If you do this while the veh icle is moving,
you will be out of position. Always adjust
the dr iver's or front passenger's seat
when the vehicle is not moving.
- Be careful when adjusting the seat
he ight. Check to see that no one is in the
way, or serious injury cou ld result!
- Because the seats can be electrically ad­
justed with the ignition off, never leave
children unattended in the vehicle. Unsu­
pe rvised use of the electric seat adjust­
ments may cause serious injury .
- To reduce the risk of injury in the case of
sudden braking or accident, front pas­
sengers must never r ide in a moving ve­
hicle with the backrest reclined. Safety
be lts and the airbag system on ly offer
maximum protection when the backrest
is upright and the safety belts are prop­
erly positioned on the body. The more
the backrest is reclined, the greater the risk of personal injury from an incorrect
seating position and improperly posi­
tioned safety belts.
Armrest
There is a storage compartment under the
armrest.
Fig. 46 Cockp it : center armrest

should never be left unattended in the ve­
hicle because this increases the risk of in­
jury.
12-volt sockets
Fig. 5 4 Section of the trim panel of the luggage com·
partment: 12-volt socket
•
Fig . 55 Rear center console: 12-volt socket
~ To reach the 12-volt socket in the luggage
compartment, press the net down
¢ fig. 54.
There is an additional 12-vo lt socket in the
front and rear center console
~fig. 55.
The 12 vo lt sockets may be used for 12-volt
appliances with max imum consumption of up
to 120 watts.
Before you purchase any accessories, always
r ead and fo llow the information in
~ page 280, Additional accessories and parts
replacement .
A WARNING
The sockets and the electrica l accessories
connected to them operate on ly when the
ignition is switched on. Incorrect usage
can lead to serious injuries or burns. To re­
duce the risk of injuries, never leave chil-
S ea ts a nd s to rage 55
dren unattended in the vehicle with the ve­
h icle key.
(D Note
To avoid damaging the socket, only use plugs that fit properly.
- Never connect equipment that generates
electrical current, such as a solar pane l
or battery charger, to the 12 volt socket.
This could damage the vehicle's electri­
cal system.
- The 12 volt socket should only be used
for a short period of t i me as a power
source for electrical equipment. Please
use the electrical sockets in the vehicle
when connecting equ ipment for longer
periods.
- To avoid damaging the socket, only use
plugs that fit properly.
(D Tips
When the engine is off and accessories are
still plugged in and are on, the vehicle bat­
tery can still be drained.
Storage
(upholder
Fig. 56 Center console: cupholder
Fig. 57 Rear center armrest: cupholder extended