ignition AUDI S7 2016 Owner's Manual

M N <( I.J "". rl I.O
"' N I.O rl
.. To increase or reduce the brightness, turn the
knob and press it .
The inte rior lighting turns on when you switch
the headlights on whi le the ignition is on .
(D Tips
The setting is automat ically stored and as­
signed to the remote control key that is in
use.
Instrument illumination
The brightness of the illumination for the instru­
ments, display and head-up display* can be ad­
justed.
Fig. 41 Instrument illumination
.. Press the knob to release it.
.. Turn the knob toward" -" or"+" to reduce or in ­
crease the brightness.
.. Press the knob again to return it to its original
pos ition.
@ Tips
The instrument illumination for the needles
and dia ls turns on when the ignition is turned
on and the lights are turned off. The illumina­
tion for the dials reduces automatically and
eventually turns off as brightness outside in­
creases. This function reminds the driver to
turn the headlights on at the appropriate
time.
Lights and Vision
Vision
Adjusting the exterior mirrors
Fig. 42 Driver 's doo r: knob fo r the exterior mirrors
Turn the knob to the desired position:
Q/P -Adjusting the left/right exterior mirror.
Move the knob in the des ired direction.
4iil -Heating the mirror glass depending on the
outside temperature.
8 -Folding exterior mirrors*. In the Infotain­
ment system , you can select if the mirrors fold in
a utomat ically when you lock the vehicle
~page 33.
Front passenger's exterior mirror tilt
function*
To help you see the curb when backing into a
parking space, the surface of the mirror tilts
slight ly . For this to happen, the knob must be in
the position for the front passenger's outside
mirror.
You can adjust the tilted mirror surface by turn­
ing the knob in the desired direction. When you
move out of reverse and into another gear, the
new mirror position is stored and assigned to the
key you are using.
T he m irror goes back into its orig inal position
once you drive forward faster than 9 mph (15
km/h) or switch the ign ition off.
A WARNING
-Curved (i . e. convex) mirror surfaces increase
your f ield of view . Remember that veh icles or
other objects will appear smaller and farther
away than when seen in a fla t mirror . If you
47

Ligh ts a nd Vi sion
by moving the lever to position ® within 10 sec ­
onds after the afterwipe. The afterwipe function
is reactivated the next time you switch the ign i­
tion on.
Cleaning the headlights *. The headlight washer
system* operates only when the low beam head­ lights are on. If you move the lever to position
® , the headlights and the night vision assist
camera* are washed in intervals.
A WARNING
-The rain sensor is only intended to assist the
dr iver . The driver is st ill responsible for
manually switching the wipers on according
to the v is ibility conditions.
- The w indshield may not be treated w ith wa­
te r-repell ing windsh ield coating agents. Un­
favorable conditions, such as wetness, dark­ ness or low sun, can resu lt in increased
glare, which increases the risk of an acci ­
dent. Wiper blade chatter is also possible.
- Properly functioning w indshield w iper
blades are required for a clear view and safe
driving ~
page 50, Replacing windshield
wiper blades.
(Jd) Note
- If there is frost, make sure the windshield
wiper blades are not frozen to the wind ­
s h ield. Switching on the winds hield wipers
when the blades are frozen to the wind­
sh ield can damage the wiper blades.
- Prior to using a car wash, the winds hield
wiper system must be switched off (lever in
position 0). This prevents unintentional
switching on and damage to the w indshield
wiper system.
(Di Tips
- The windshield wipers switch off when the
i gnition is turned off. You can act ivate the
windsh ield wipers after the ignition is
switched back on by moving the windsh ield
wiper lever to any pos it ion.
- Worn or dirty windshield w iper blades result
i n streaking. This can affect the rain sensor
so
f unction. Check your w indshield wiper
blades regu larly .
- T he washer fluid nozz les o f the windshie ld
washer system are heated at low tempera­
t ur es when the ignition is on.
- When stopping temporarily, such as at a traffic light, the speed of the windshield
wipers automatica lly reduces by one leve l.
Cleaning windshield wiper blades
Clean the wiper blades when you see wiper
streaks. Use a soft cloth and a glass cleaner.
.,. Place the windshie ld wiper arms in the service
position
c:> page 50.
.,. Fold the windshie ld w iper arms away from the
w indshield.
A WARNING
Dirty windsh ield wiper b lades can impair vi­
sion, wh ich increases the risk of an accident .
Replacing windshield wiper blades
Fig. 47 Remov ing windshield wiper blades
Wiper serv ice position /bla de repl acement
posit ion
.,. Switch the ignit io n off and move the windshield
w iper lever to position @briefly
c:> page 49,
fig. 46. The w indshie ld w ipers move into the
service pos ition.
.,. To bring the w iper blades back into the or igina l
position, switch the ignition on and ope rate the
windshield wiper lever.
You can also tu rn the se rv ice position on or off in
t h e Info tainment sys tem: .,..

M N <( I.J -<I'. rl I.O
"' N I.O rl
Front passenger's seat
Always move the front passenger seat into the rearmost position .
To avoid contact with the airbag while it is de­
ploying, do not sit any closer to the instrument
panel than necessary and always wear the three­
point safety belt provided adjusted correctly . We
recommend that you adjust the passenger's seat
in the following manner:
.. Bring the backrest up to an (almost) upright
position .
Do not ride with the seat reclined .
.. For adjustable head restraints: adjust the head
restraint so the upper edge is as even as possi­
ble with the top of your head. If that is not pos­
sible, try to adjust the head restraint so that it
is as close to this position as possible
c:::> page 55. Move the head restraint so that it
is as close to the back of the head as possible.
.. Place your feet on the floor in front of the pas­
senger's seat .
Front seats
Controls
Moving the seat forward or back and adjusting
the height, backrest angle and seat angle.
Fig. 48 Front seat: adjusting the seat
@-Moving the seat forward/back: press the but­
ton forward/back ¢ .&,.
@ -Moving the seat up/down: press the button
up/down
c:::> .&, . To adjust the front section of the
seat, press the front button up/down
c:::> .&, . To ad­
just the rear section of the seat, press the rear button up/down
c:::> .&,.
Seats and storage
@ -Turn the massage function* on/off. You can
select the type of massage using the multifunc­
tion button
c:::> page 54.
© -Backrest forward/back: press the button for­
ward/back ¢.&, .
(D-Lumbar support* : press the button in the
corresponding position
c:::> .&. or multifunction
button*¢ .&.,
c:::> page 54 .
& WARNING
=
-Never adjust the driver's or front passeng-
er 's seat while the vehicle is moving. If you
do this while the vehicle is moving, you will
be out of position. Always adjust the driver's
or front passenger's seat when the vehicle is
not moving.
- Be careful when adjusting the seat height.
Check to see that no one is in the way, or se­
rious injury could result!
- Because the seats can be electrically adjust­
ed with the ignition off, never leave children
unattended in the vehicle . Unsupervised use
of the electric seat adjustments may cause
serious injury.
- To reduce the risk of injury in the case of
sudden braking or accident, front passen­
gers must never ride in a moving vehicle
with the backrest reclined. Safety belts and
the airbag system only offer maximum pro­
tect ion when the backrest is upright and the
safety belts are properly positioned on the
body. The more the backrest is reclined, the
greater the risk of personal injury from an incorrect seating position and improperly
positioned safety belts.
-
53

Seats and storag e
Multifunction button
Applies to vehicles: with memory function
You con adjust the massage function, lumbar
support, side bolsters and seating surface using
the multifunction button .
Fig . 4 9 MMI display: seat settings
Operating
.. The MMI displays the possible seat sett ings @
when you tu rn the m ultif unction button @
¢
page 53, fig. 48 to the left or right¢ fig. 49,
¢£ .
.. To select a seat setting, turn the multifunction
button
(D unti l the desired seat setting is h igh­
lighted with a red border .
.. The arrows @ indicate the possib le adjust­
ments . For example, to move the lumbar sup­
po rt down, press the multifunction button
(D
down. The corresponding arrow © lights up .
The following seat sett ings @are possible:
Mas sag e function* -Massage type Wave, K nock ­
ing, Stret ch , Lumbar , Shoulder or Off .
You can
set the massage strength level from 1 to 5. You
can turn the selected massage on/off using the
button @¢
page 53, fig . 48.
L u mbar support -Moving the lumbar support
up/down and making it firmer/softer¢ &,.
Side bolst ers* -Increasing/reducing the side sup­
port in the seat using the side bolsters on the
seating surface and backrest¢&, .
Se ating surfac e -Making the seating surface lon­
ge r/shorter ¢ &, .
54
A WARNING
-Never adjust the driver's or front passeng­
er's seat while the veh icle is moving. If you
do this while the veh icle is moving, you will
be out of posit ion . Always adjust the d river's
or front passenger's seat when the vehicle is
no t moving.
- Be careful when adjusting the seat he ight.
Check to see that no one is in the way, or se­
r io us inju ry co uld resul t!
- Because the seat s can be elec trically adjust­
ed w ith the ignition off, never leave children
unattended in the vehicle. Unsupervised use
of the e lectric seat adjustments may cause
serious injury .
- To reduce the risk of injury in the case of
sudden b raking or accident, front passen ­
gers must never ride in a moving veh icle
with the backrest reclined. Safety belts and
the airbag system only offer max imum pro­
tect ion when the backrest is upright and the
safety belts are properly positioned on the
body . The more the backrest is recl ined, t he
greater the ris k of persona l inju ry from an
incor rect seating posit ion and imprope rly
positioned sa fety belts .
(D Tips
- The massage funct ion sw itches off automat­
ically after approximately 10 minutes.
- The side bolsters* deflate when the d river's
door is ope ned . Th is allows you to enter and
ex it comfortably. The side bolsters i nflate
ag ain once you begin drivi ng.

M N <( I.J "". rl I.O
"' N I.O rl
Remote Memory button control key
Driver Driver Front passen-ger
Seat X X X
Stee ring wheel* X X
Both exterior X X
mirrors*
Remote control key
Applies to vehicles: with memory function
The
driver's seat profile can be assigned to the
remote control key when the vehicle is locked.
• Se lect: the ICARI function button > (Car)* Sys­
tems
contro l button > Vehicle settings > Driv­
er's seat
> Remote control key > On .
(D Tips
If you do not wish to have the seat profile for
another driver assigned to the remote control
key, switch the memory function off in the In­
fotainment system or using the IOFFI button
r=;;,page 57.
Memory buttons
Applies to vehicles: with memory function
Fig. 54 Driver's door: Memory function buttons
The memory buttons are located in the dr iver's/
front passenger's door*.
Switching the memory function on/off
• Press the IOFF i button to switch the memory
function on/off. The
LED in the button turns on
Seats and storage
when the memory function is off. Seat profiles
are neither stored nor recalled.
Storing a seat profile
• Press the lSET I button. When the word SET
lights up, the memory is ready to store set­
tings.
.. Now press a memory button briefly.
A tone con­
firms that the settings were stored .
Accessing a seat profile
• If the driver's door is open and the ignition is
switched off, press the memo ry button.
• If the driver's door is closed or the ignition is
switched on, press and hold the memory but­
ton unti l the seat adjustment is complete .
A WARNING
-For safety reasons, the seat setting can on ly
be recalled when the veh icle is stationary­
otherwise you risk having an accident.
- If necessary, you can stop the recall process
by pressing the !O FF ! button or any memory
button .
Adjusting the front passenger's seat in the
Infotainment system
Applies to vehicles: with memory function
The driver can move the front passenger's seat
into various positions.
Adjusting the front passenger's seat from
the driver's seat
• Select: the I CAR I function button > (Car)* Sys­
tems
control button > Vehicle settings > Seats
> Front passenger's seat > Adjust seat posi­
tion .
• Yo u can now adjust the front passenger's seat
using the driver's seat buttons
r::;;, page 53,
fig. 48.
Align with driver's seat
• To transfer the settings from the driver's seat
to the front passenger's seat , select: the I CAR !
function button
> (Car)* Systems control but ­
ton
> Vehicle settings > Seats > Front passeng-
er 's seat > Align with driver 's seat. ...,
57

Warm and cold
mode switches off. The temperat ure shou ld be
set to approximately 72 ° F (22 °C).
The
IAU TOI button switches the defroster off.
I® REAR I Switching the rear window defogger
on /off
The rear w indow heater only operates when the
engine is r unning.
It sw itches off automatically
after a few m in utes, depending on the outs ide
temperature.
To prevent the rear w indow heater from switch ­
ing
off a utomat ica lly, press and hold the!@ R EAR I
but ton fo r more than 2 seconds. This rema ins
stored until the ignition is switched
off.
Q:I Adjusting seat h eating *
Pressing the button switches the seat heating on
at the highes t setting (level 3) . T he LEDs indicate
the tempe rature leve l. To red uce the tempe ra­
ture, press the button again. To switch the seat
heating
off , press the button repeatedly until the
LED turns
off .
Afte r 10 minutes , the seat heat ing a utomat ica lly
sw itches from level 3 to leve l 2 .
Air vent s
You can open or close the center and rear vents in
the cockpit and the vents in the rear center con­
sole using the r idged thumbwhee ls. The levers
adj ust the d irect ion of the a irf low from the vents.
70
A WARNING
-
- You should not use the recirculation mode
for an extended period since no fresh air is
drawn in . With the a ir-conditioning sw itched
off, the windows can fog up, which increases
the r isk of a n accident.
- Individuals w ith reduced sensitivity to pain
or temperatu re could develop burns when
using the seat heat ing f unct ion. To reduce
the r isk of inj ury, these indiv iduals should
not use seat heating.
(D Note
To avoid damage to the heat ing e lements in
the seats, do not kneel on the sea ts or place
h eavy loads on a sma ll area o f the seat .
Basic settings
Applies to vehicles: wit h three-zone climate control
The climate control system basic settings are ac­
cessed in the Infotainment system.
~ Select: the I CARI funct ion button > ( Car )* S ys-
t e m s
control button > AC.
Au xilia ry heater*
In vehicles with diesel engines, the auxiliary heat­
er helps to warm the vehicle interior more quick­
ly. The aux iliary heater is controlled automatical ­
l y in the
A ut o setting .

Warm and cold
At both of these settings, the climate control sys ­
tem runs continuously at maximum cooling or heating power. There is no temperat ure regula­
tion.
Adju st ing th e bl ow er[!]
You can ad just the volume of air generated by the
b lower to yo ur preference. To have the blower
reg ulated automatically, press the
!AUTO I button .
~ Adjusting air d istribution
You ca n manually se lect the vents whe re the air
w ill flow. To have the air distrib ution regu lated
automatically, press the
! AUTO ! button.
~ Adjusting seat heating * /se at vent ilation*
Pressing the button switches the seat heating/
seat ventilat ion on at the highest setting ( leve l
3). The LEDs indicate the tempe ratu re leve l. To
red uce the tempe ratu re, p ress the butto n aga in.
To switch the seat heating/seat venti lation off,
press the button repeatedly until the LED turns
off .
After 10 minutes, the seat heating automat ica lly
switches from leve l 3 to leve l 2 .
I@ FRONT I Switching the defroster on /off
The windsh ield and s ide windows are defrosted
or cleared of condensation as quickly as possible.
The max imum amo unt of air flows ma inly from
t he ven ts below the w indshie ld. Rec irc ulat ion
mode switches off . The temperature shou ld be
set to approximately 22
°C.
The IAUTOI b utton swi tches the defroster off.
IOiil REAR I Switching the rear window defogger
on /off
The rear w indow heater only operates when the
eng ine is running.
It sw itches off automatically
after a few m in utes, depend ing on the outs ide
temperature.
To prevent the rear w indow heater from switc h­
ing off a utomat ica lly, press and hold the
!l:iil REAR I
button fo r more t han 2 seconds. This rema ins
stored until the ignition is switched off.
72
I SYNC I Sy nchron izat ion
When synchroni zation is swi tched on, the set­
tings for the driver's side a re applied to the front
passenger's side (except for seat heating/ventila­
tion*). The settings in the rear are also synchron­ ized. Synchronization switches off if the settings
are adjusted on the front passenger's side or in
the rear.
You can synchronize the settings in a row by
pressing and holding a control. For example, to
apply the settings for the front passenger's side
to the driver's side, press and ho ld the control on
the front passenger's side. The same applies to
the rear .
Residual he at*
With the ign ition turned off, you can activate the
residual heat function by pressing the
[!:I button
<=> fig . 76 . The residua l heat from the coolant is
u sed to heat the veh icle interior. The residual
heat funct ion switches off automatically after
about 30 minutes.
Air vents
You can open or close the center and rear vents in
the cockpit and the vents in the rear center con­
sole and door pillars using the ridged thumb­
whee ls . T he levers adjust the direct ion of the air­
flow from the vents.
.8, WARNING
- You should no t use the re ci rculation mode
for an extended period since no fresh air is drawn in. With the a ir-conditioning switched
off, the windows can fog up, which increases
the risk of an accident.
- Individ ua ls with red uced sensitivity to pain
or temperat ure could deve lop burns when
using the seat heating f unction. To reduce
the risk of inj ury, these indiv iduals should
not use seat heating .
(D Note
To avoid damage to the heating e lements in
the seats, do not kneel on the seats or place heavy loads on a small area of the seat.

M N <( I.J "". rl I.O
"' N I.O rl
There must be at least 10 inches (25 cm) be­
tween your chest and the center of the steering
wheel.
If you cannot sit more than 10 inches (25
cm) from the steering wheel, see if adaptive
equipment is available to help you reach the ped­
als and increase the distance from the steering
wheel.
For detailed information on how to adjust the
driver's seat, see
r:::>page 53.
In vehicles with the memory function*, the steer­
ing column settings are stored together with the
seat position.
A WARNING
Improper use of steering wheel adjustment
and improper seating position can cause seri­
ous personal injury.
- Adjust the steer ing wheel column only when
the vehicle is not mov ing to prevent loss of
vehicle control.
- Adjust the driver's seat or steering wheel so
that there is a minimum of 10 inches (25
cm) between yo ur chest and the steering
wheel
r:::>page 127, fig. 144. If you cannot
mainta in this min imum d istance, the a irbag
system cannot protect you properly .
- If phys ica l limitations prevent you from sit­
ti ng 10 inches (25 cm) or more from the
steering wheel, check with your authorized
Audi dealer to see if adaptive eq uipment is
available.
- If the steering wheel is aligned wi th your
face, the supp lemental driver's airbag can­
not provide as much protection in an acci­
dent. Always make sure that the steering
wheel is aligned w ith your chest.
- Always hold the steering wheel with your hands at the 9 o'clock and 3 o'clock posi­
t ions to reduce the r isk of personal injury if
the driver 's airbag deploys.
- Never hold the steer ing wheel at the 12
o'clock posit ion or w ith your hands inside
the steering wheel rim or on the steering
wheel hub. Holding th e steering wheel the
wrong way can cause se rious injuries to the
hands, arms and head if the driver's a irbag
dep loys .
Drivi ng
Easy seat entry
Applies to vehicles: with power steering wheel adjustment
Easy seat entry makes it easier to enter and exit
the vehicle by adjusting the steering column au­
tomatically.
.. In the Infotainment system, select: the ICARI
function button > ( Car) * Systems control but­
ton
> V ehicle sett ings > Se ats> Driver 's se at>
Ea sy se at entry > On .
When easy seat entry is sw itched on, the steering
column goes back up into the park pos ition when
the ignit ion is switched off . After entering the ve­
hicle, the steeri ng column returns to the stored
pos ition once the ig nit ion is switched on.
Starting and stopping
the engine
Starting the engine
The I STAR T ENGIN E ST OPI button switches the
ignition on and starts the engine .
Fig . 8 1 Center console: START ENGINE STOP button
Sta rting the engine
.. Press the brake pedal a nd move the selector
lever to the P o r
N position.
.. Press the
I START ENGINE STOP j button . The
eng ine will start .
.. It is possib le that there will be a slight delay
when starting the engine in diesel vehicles in
colder temperatu res. Therefore, you must hold
the brake pedal down unt il the engi ne starts .
The indicator light turns on whi le the engine is
preheating
m . ...
75

Driving
Sw it c h ing th e ig nit ion on /off
If you wou ld like to switch the ignition on with­
out starting the engine, fo llow these steps :
"' Press the
!START E NGIN E STOPI button with-
out pressing the brake pedal.
"'T o sw itch the ignition off, press the button
again. The needle in the tachomete r moves into
the
O FF pos ition.
The prewarm ing runs automati cally in diese l
vehicles when the ignition is switched on .
Equipment that uses a lot of electricity is switch­
ed off temporar ily when you start the engine.
If the engine should not start immediately, the
starting process is automat ically stopped after a
short time . Repeat starting procedure .
Start-Stop-System *
Note the information inc:> page 80, S tar t-S top­
Sys tem.
A WARNING
- Never allow the engine to ru n in confined
spaces, because this inc reases the r isk of as­
phyx iat ion.
- Never t urn off the engine before the veh icle
has come to a comp lete stop .
- The brake booster and power steer ing no
longer function whe n you stop the engine.
You must use more fo rce when bra king or
stee ring. Be cause you cannot b rake and
steer as you us ually wou ld, this could lead
to accidents and se rious i njuries. These
functions are still active if the Start-Stop­
System* has stopped the engine.
([) Note
Avoid high engine speed, fu ll th rottle , and
heavy eng ine load as lon g as the engine has
not reached operating temperature yet. You
co uld damage the engi ne .
@ For the sake of the environment
Do not let the engine r un while parked to
warm up. Beg in driving immed iately . This re­
duces u nnecessary emissions .
76
-
(D Tips
-After starting a cold engine, there may be a
br ief per iod of increased noise because the
oil pressure must first bui ld up in the hy­
draulic valve adjusters. This is normal and
not a cause for concern .
- If you leave the veh icle with the ignition
switched on, the ign ition w ill switch off af­
ter a certain amount of time . Make sure that
electrical equipment such as the exterior
l ights a re switched off.
Stopping the engine
"' Br ing your vehi cle to a complete stop.
"' Move the se lector lever to the P o r N posit ion .
"' Press the
I STA RT ENGINE STOP ! button
c:> page 75, fig . 81 .
Steering lock
The steering locks when yo u tur n the eng ine off
us ing the
I S TAR T ENGINE ST OP I button and open
the driver's doo r. The locked steering helps pre ­
vent vehicle theft.
Emergency off
If necessary, the engine can be switc hed off with
the se lecto r lever in the R or D/S posit ion. The en­
gine stops if yo u press and hold the
I S TAR T ENGINE ST OP I button at speeds below
6 mph (10 km/h) and press the brake peda l.
A WARNING
-Never turn off the engine until the vehicle
has come to a complete stop.
- The brake booster and power steering only
work when the engine is running . If the en­
gine is off , you have to use more force when
steering or braking. Because you cannot
steer and brake as you usually wou ld, this
could lead to crashes and serio us in ju ries.
- For safety reasons, you should always pa rk
your veh icle with the selector lever in P. Oth ­
erw ise, the vehicle could inadve rtently ro ll
away.

M N <( I.J "". rl I.O
"' N I.O rl
-After the engine has been switched off , the
radiator fan can cont in ue to run for up to 10
minutes - even with the ign ition sw itched
off . It can a lso switch on again after some
t i me if t he coolant tern pera ture rises as the
result of a heat bu ildup or if the engine is
ho t and the engi ne compa rtmen t is addi­
ti onal ly he ate d by the su n's ra ys.
(D Note
Do not stop the engine imme diate ly afte r
ha rd or extend ed dr iving . K eep the engi ne
r u nning for app roximately two m inutes to
p reven t exces sive heat build-up.
Messages
Turn off ignition before leaving car
This message appea rs and a war ning tone sounds
if you open the d river's doo r whe n the ignition is
switche d on .
Press brake ped al to start engine
This message appears if you do not press the
brake peda l when starting the engine.
Ill Is key in the vehicle?
This indi ca tor light tur ns on and t his message ap­
pears i f the ignit ion key was removed from the
ve hicl e when the e ngine was ru nning . If the igni ­
tion key is no longer in the vehicle, you cannot
switch on the ignit ion or start the engine once
you stop it. You also cannot lock the veh icle from
the outside.
Shift to P , otherwise vehicle can roll away.
Doors do not lock if lev er is not in P.
This message appears for sa fe ty reasons if the
tra nsmission is not i n the P position when you
switch the ignition off . Move the selector lever to
the P pos ition . Otherwise the vehicle is not pro­
tected from roll ing and it cannot be locked.
DJ Key is not recognized . Hold back of key
again st ma rked a rea. See owner's manual
If the i ndic ator lig ht turns on and th is mess age
appears, there is a malfunction ~
page 77.
Driv ing
Turn off ignition before leaving car. Battery is
di scha rging
T his dr iver message appears if the drive r's door is
o pened wh ile the ign ition is switched on. Always
switch off the ignition if you are leav ing t he veh i­
cle . Refer to
¢ page 81.
Shift to P and turn off ignition b efore leaving
car , otherwise vehicle can roll away
This message appears if the drive r's door is
opened wh ile the ign ition is switched on and the
sele ctor lever is not in the P position . Move the
se lector lever in to the P posi tion a nd switch the
i gnition off when you exit the vehicle . Otherwise
t h e vehicle co uld ro ll. Refer to ¢
page 81.
Starting the engine when there is a
malfunction
It may not be possible to start the engine under
certain circumstances, for example if the battery
in the vehicle key is drained , if interference is af­
fected the key or if there
is a system malfunc ­
tion .
Fig . 8 2 Ce nte r c onsol e/master key : s tar ting t he e ngin e
w hen t here is a ma lf un ctio n
Requirement: The message Key is not recog­
nized. Hold back of key against marked are a.
Se e owner 's manual
is displayed and the DJ indi­
c ator lig ht tu rns on.
.. Hold the master key i n the location indicated as
shown in the illustration
f>l) ¢ fig . 82 .
.. Press the brake pedal ¢ A. in Starting the en­
gine on page
76.
.. Press the
~ IS_ T_A_ R_T _E_N_G-IN_E_S_ T_O_P ~I bu tton. The
eng ine will start .
77