warning light AUDI TT 2013 Owner´s Manual

194 Checking and filling
When charging at low voltages (e.g . w ith a
tri ckle charger ), the battery cables do not
have to be d isconnected first. Be fore charging
at
high voltages, i.e. " fast charging ", you
must disconnect both cables. In e ither case,
follow the instruct ions from the ma nufacturer
of the charger .
Fastcharging a battery is
dangerous c:> .&. in
Working on the battery on page 192 .
It re­
qu ires specia l charg ing equipment a nd the
k nowledge to go wi th it. We recomme nd hav­
ing your battery fast charged on ly by a quali­
fied workshop.
A discharged batte ry can
freeze at tempera­
tures of on ly 32 °F (0
°(). A llow a frozen bat­
tery to thaw completely befo re attempt ing to
cha rge it
c:> ,&. . Howeve r, we re comme nd not
usi ng a thawe d batt ery again bec ause t he bat­
tery cas ing ca n be cracked d ue to ice forma ­
tion and can lea k bat tery aci d.
D o not open the batte ry caps whe n charg ing
the ba ttery.
_&. WARNING
-
Cha rging a batte ry can be dange rous.
- N ever charge a fro zen b att ery .
It may ex­
plode beca use o f gas t rappe d in t he i ce.
Allow a frozen battery to thaw o ut first .
- D o no t reu se batte ries which we re fr o­
zen . The batte ry housing m ay h ave
c rac ked an d weakened whe n the battery
froze .
- C harge the b attery in a we ll ven tilated
area . Kee p away from open flame o r elec­
trical spa rk. Do not smoke. Hydrogen gas
generated by the battery is exp losive.
- To reduce the danger o f explosion, never
co nnect or disconnect charger cables
wh ile the charger is operating .
- Fast charg ing a battery is dangerous and
shou ld on ly be attempted by a compe­
tent technician w ith the proper eq uip­
me nt.
- Battery acid that may spill d uring charg­
ing should be washed
off wit h a so lution
of warm water and baki ng soda to neu ­
t raliz e the aci d.
(D Note
Neve r use a fast charger as a booster to
start the eng ine. Th is w ill seriously dam­
age sensit ive e lectronic components, such
as cont ro l units, re lays, radio, etc. , as well
as the battery charge r.
(D Tips
The vehicle batte ry must not be charged
with a standard small charger that plugs in to the c igarette lighter or outlet.
Windshield/headlight
washer container
Fi g. 141 Fen der, left: cove r o n th e w inds hield a nd
h ead lig ht• wa sher fl uid re se rvoir
T he was her fluid co nta iner is mar ked w it h the
symbol
Q o n its c a p<=> page 182, fig . 134.
""' Before yo u check anything in the engine
compa rtme nt,
always read and heed all
WARNINGS c:> ..&. in Wor king in the engine
c ompartment on page 18 0.
""' Lift th e fill er ca p tongue to ad d washer flu­
id . You can f ill the containe r to the top .
""' Press the cap back o nto the fi ller neck after
fi lling the container.
You can find the reservo ir
capacity in t he table
in
<=> page 24 0
Clean wa ter should be used when filling up. If
poss ible, use so ft wat er to preven t sc aling o n
t h e washer jets . A lways ad d a glass clea ner
solution (with frost protection in the winter) . ..,.

forget the spare tire. If the press ure in any tire
is too high when the tire is "cold," let air out
of the tire slowly with the edge of the t ire
gauge and keep checking the pressure until
you reach the pressure that is correct for the
load (passengers and luggage) and kind of
driving you plan to do .
If the pressure in any tire is too low, note the
d ifference between the pressure in the cold
tire and the pressure you need and add the a ir
that you need to reach the correct pressure for
the veh icle load (passengers and luggage) for
the tires on your veh icle as listed on the on
your ve hicle and in this manua l and the kind
of dr iving you p lan to do .
Never exce ed the ma ximum inflation pres ­
s ur e listed on t he tire s idewall for any re a­
s on.
Remember that the vehicle manufacturer , not
the t ire manufacturer , determ ines the correct
tire pressure for the tires on your veh icle .
It is important to check the tire pressure when
the t ires a re cold .
- Read the req uired tire press ure from the tire
pressure label located on driver's s ide B-pil­
l ar .
- Turn the valve stem cap counter-clockwise
to remove it from the tire valve .
- Place the air pressure ga uge on the valve.
- The tire pressures sho uld on ly be checked
and adjusted when the tires are cold . The
s light ly raised pressures of warm tires must
not be reduced.
- Adjust the tire pressure to the load you are
carrying.
- Re insta ll the va lve stem cap on the valve .
When should I check the tire pressure?
The correct tire pressure is espec ially impo r­
tant at high speeds . The pressure sho uld
therefore be checked at least once a month
and a lways befo re starting a journey.
When should I adjust the tire pressures?
Adj ust the tire pressu re to the load you are
carry ing . After changi ng a wheel
or replacing
Tire s an d wheel s 203
whee ls yo u have to adjust the ti re p ressu res
o n all whee ls. In addition, yo u m ust then initi­
a lize the new tire pressu res in the t ire pres­
s u re monitoring system
Q page 214.
A WARNING
Incorrect tire pressures and/or underinfla­
tion can lead sudden tire fa ilure, loss of
control, collision, serio us pe rsonal injury
or even death.
- When the warning symbol
[I] appears in
the instrument cluster, stop and inspect
the t ires.
- Inco rrect tire pressure and/or underinfla­
tion can cause increased tire wea r and
can affect the handling of the vehicle and
stopping ability.
- Inco rrect tire pressures and/or underin­
flation can a lso lead to sudden t ire fail­
ure, including a blowou t and su dden de­
flation, ca using loss of veh icle cont ro l.
- Th e drive r is responsi ble for the correc t
tire pressures for all tires on the veh icle.
The applicable pressure values a re locat ­
ed on a sticke r on the dr iver's side B-pil­
lar.
- On ly when all tires on the vehicle are fil ­
led to the correct pressure, the t ire pres­
sure mon itor ing system can work cor­
rectly.
- The use of incorrect tire pressu re va lues
can lead to acc idents or other damage.
Therefore it is essential that the driver
observe the spec ified t ire pressure values
for the tires and the correct pressures for
the function of th e ti r e p ressu re monito r­
ing system.
- Always inf late tires to the recommended
a nd correct t ire p ress ure before dr iv ing
off.
- Driving with unde rinflated tir es bend
mo re, letting t hem get too hot resulting
in tre ad separation, sudden tire f ailure
and loss of cont rol.
- Exces sive speed and/overloading can
cause he at bu ild- up, sudden tire failure
an d loss of cont rol. •
•

remain continuous ly illuminated . This se ­
quence will continue upon subsequent vehicle
start-ups as long as the ma lfunction ex ists.
When the malfunct ion indicator is ill uminat­
ed, the system may not be able to detect or
signa l low tire pressure as intended. TPMS
malfunct ions may occur for a variety of rea­
sons, including the installat ion of replace­
ment or alternate tires or wheels on the veh i­
cle that prevent the TPMS from funct io ni ng
properly. Always check the TPMS malfunct ion
tellta le afte r replacing one or more t ires or
wheels on your veh icle to ensure that the re­
p lacement or a lternate tires and wheels allow
the TPMS to continue to function properly.
Tire pressure indicator appears
Applies to vehicles: with tire pressure monitoring system
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction.
F ig. 1 47 Disp lay : under infla tion warn ing
Using the ABS sensors, the tire pressure moni ­
toring system compares the t ire tread circum­
fe rence and vibration characteristics of the in­
d iv idual tires . If the pressure decreases in one
or mo re tires, th is is indicated in the instru­
ment clus ter with a warning symbol
RE and a
message
'* fig. 147. The dr iver message in the
d isp lay goes out after 5 seconds. The driver
message can be d isplayed again by pressing
the
! CHECK I button @¢ page 10, fig . 3 . If on ­
ly one tire is affected, the display will indicate
its pos ition.
The ti re pressure monito ring m ust be reset in
the menu display each time the pressures are
ad justed (e.g. when switching between parti-
Tire s an d wheel s 215
al and fu ll load pressure) or after changing o r
replacing a tire on your vehicle '*
page 216.
The TPMS indicator on ly mon itors the t ire
pressure that you have previously stored . You
can f ind the recommended tire pressures for
your vehicle on the label on the driver's door
pillar ¢
page 200.
Tire tread circumference and vibration charac­
teristics can change and cause a tire pressure
warning if:
- the t ire press ure in one or more tires is too
low,
- the tire has structural damage,
- the t ire press ure was changed, wheels rotat -
ed or rep laced but the TPMS was not reset
¢ page 216.
Warning symbo ls
RE L oss of pressure in a t least one tire ¢ ,&..
Check the tire or tires and rep lace or repa ir if
necessary . The indicator light
RE in the inst ru­
ment cluster a lso i lluminates
¢ page 13 .
Check/correct the press ures of all four tires
and reset TPMS in the menu display .
Iii;~, (T ire Pressure Monitoring System) Ti re
pre ssure! System malfun ction .
Ifllilff' ap­
pears after switching the ignition on or whi le
driv ing and the indicator light
RE in the in­
strument cluster blinks for approx imately one
minute and then stays on, there is a system
malfunction .
Attempt to store the correct tire pressure '*
page 216. If the indicator light does not
turn off or if it turns on shortly thereafter, im ­
med iate ly dr ive your vehicle to a n author ized
Audi dealer or author ized repair fac ility to
have the malfunct io n cor rected.
.8, WARNING
-
- If the tire pressure ind ic a tor ap pears in
the ins trumen t cluster display, one or
more of your tires is significant ly under­
inflated . Reduce yo ur speed immediately
and avoid any hard steer ing or braking
maneuvers. Stop as soon as possible and
check the tires and their pressures.
~
•
•

Handling characteristics change when
driving with low air pressure or with flat
tires even with special run-flat tires
A low pressure or flat front tire affects vehicle
handling characteristics by pu lling the vehicle
slightly to the side where the tire is mounted
and reduces braking performance .
A low pressure or flat
rear tire also affects
driving character istics by pulling to the side
where the tire is mounted and also reduces
brak ing performance. The effect on vehicle
handling is most not iceable when driving
around curves.
A WARNING
Changed vehicle handling character istics
when driving in the run -f lat mode can
cause loss of vehicle contro l, a crash and
serious personal injury.
- Driving on special run-flat tires in the
run-f lat mode wi ll change vehicle han­
dling characteristics during braking,
when cornering and under heavy acceler­
ation.
- Never drive faster than the maximum
rated speed of 50 mph (80 km/h) when
dr iv ing in the run -flat mode.
- Always adjust vehicle speed to traffic,
road and weather cond itions and drive
slower than the max imum rated speed if
necessary weather and road conditions
are taken into account.
- Always obey speed limits and other traf­
fic laws.
Q) Note
We always recommend driving w ith even
more care when using these special t ires in
the run-flat mode . Always avo id sudden
maneuvers.
Tires and wheels 219
Replacing run-flat tires and rims
App lies to veh icles : w it h Run -flat t ires
Your vehicle was especially designed to use
special run-flat tires.
You may use and combine only approved run­
flat tires and special matching rims that have
been designed for run-flat tires . Mounting
special run-flat tires on standard wheels will not work and w ill not prov ide the advantages
fo the ru n-falt feature . Never use spec ial run­
flat tires on standa rd wheel rims.
After dr iving with a tire i n the run-flat mode,
always have the vehicle and affected tire(s)
and rim(s) inspected by a n authorized Audi
dealer. Tires that have been driven in the run­
f lat mode must be rep laced .
A WARNING
-Use of damaged run-flat tires and rims can
cause vehicle damage that can lead to loss
of vehicle control, a crash and serious per­
sonal injury.
- Always have the vehicle and affected
tire(s) and r im(s) inspected by an author­
ized Audi dealer after driving a tire in the
run-flat mode .
- Tires that have been dr iven in the run­
flat mode must be replaced.
•
•

222 What do I do now?
• Check whether a repair using the Tire Mobi­
li ty System is possible ¢
page 2 20, General
and safety pointers.
• Have all passengers leave the vehicle and
stay away from the danger zone ¢
&,..
• Take the sealant bottle and the electric air
pump from the luggage compartment un­
der the floor ¢
fig. 154 .
• Remove the "max. SO mph" (80 km/h)
sticker from the sealant bottle and affix it to
the instr ument cluster in the driver's view.
~ WARNING
- Turn the hazard flashers on and set up
the warning triang le if you have a flat
t ire in moving traffic. In this way you pro­
tect you rs elf and other road users.
- Make sure that all passengers are in a
safe place, out of the danger zone (for
example, behind a guard rail).
(D Note
Particular care is necessary if you are mak­
ing a tire repair on a steep incline.
(D Tips
Obey all laws.
Making a tire repair
App lies to vehicles: with Tire Mobility System
Tire repair consists of the following sections.
Fig. 155 Parts of the Tire Mobility System
-
1) The ele ctr ic a ir pump s hould never ru n for lo nger than
6 min utes.
Fig. 156 Connector for the Tire Mob ility System
Assembling Tire Mobility System
• Open the lid@ of the electric air pump
¢fig. 155.
• Pull the plug@and the pressure hose ®
w ith the gauge out of the housing.
• Screw the pressure hose ® of the electric
air pump onto the flange @ of the sealant
bott le
(D .
• Push the sea lant bott le with the flange
down into th e recess @ on the lid of the
electric air pump.
• Remove the dust cap from the valve of the
defective tire .
• Screw the hose (@onto the valve
(J)
¢ fig. 156.
• Insert the plug @¢fig . 155 into the socket
for the cigarette lighter.
• Switch on the ignition .
Inflating tire
• Move the switch @¢ fig. 156 on the elec­
tric air pump
l) to position I. After 5 mi­
nutes, tire pressure must have reached at
least 1.8 bar.
• Switch the e lectric air pump off -sw itch in
position
0. If the required tire pressure of at
least 1.8 bar has not been reached, follow
the instructions in the section
Re-inflating
tire.
Re-inflating tire
• Remove the hose from the valve and pull
the plug out of the socket.

~ Drive the vehicle slow ly 10 meters back­
ward or forward. This helps to distribute the
sealant better .
~ Remove the empty inflation bott le and
screw the hose ®¢
fig. 155 from the elec­
tric pump directly onto the valve.
~ Insert the plug©¢ fig. 155 into the socket
for the cigarette lighter.
~ Switc h on the igni tion.
~ Move the switch @¢ fig. 156 on the e lec­
tric a ir pump
ll to posi tion I. After 5 mi­
nutes, tire pressure must have reached at
least 1.8 bar.
~ Switch the electric a ir pump off - switch in
position
0 . If the requ ired tire pressure of at
least 1.8 bar has not been reached, it is not
poss ible to make a repa ir with the tire seal ­
ant. Seek professional ass istance.
Disassembling Tire Mobility System
~ Remove the hose from the valve and pu ll
the plug out of the socket.
~ Screw the dust cap onto the valve.
~ Place the empty sealant bottle back in the
original packag ing and clip it in place under
the floor so that no tire sealant can run out
into the vehicle.
~ Place the elect ric air pump in the luggage
compartment for the time being.
~ Start driving right away so that the sealant
is distributed in the tire.
A WARNING
-Follow the manufacturer's safety instruc­
t ions on the deca l for the air pump and
the sealant bott le.
- If a t ire pressure of 1.8 bar cannot be
achieved after pump ing for 5 m inutes,
the tire is too severely damaged. Do not
continue to drive .
- Seek profess ional assistance if it is not
poss ible to repair the tire with the tire
sealant.
l ) The e lectr ic air pump s hould never r un for longer than
6 min utes.
What do I do now? 223
(D Tips
-Do not operate the electric air pump for
more than 6 minutes witho ut stopping,
otherwise it can overheat. When the a ir
pump has coo led down, you can continue
to use it.
- If sealant has escaped, allow it to dry,
then you can peel it off.
Final check
App lies to vehicles: wit h Tire Mobility System
After driving for a short distance, tire
pressure must be checked
~ After d riving for about 10 m inutes, stop
and check the tire pressure.
~ If tire pressure is still at leas t 1.3 bar, in­
flate the tire to specified pressure (see driv­
ers side B -pillar), drive to the next repair
shop and have the tire and the sealant bot­
tle replaced.
~ If tire pressure is less than 1.3 bar, the t ire
is too severely damaged. Do not cont inue to
drive . Seek professional assistance.
A WARNING
If t ire pressure is less than 1.3 bar after
driving for 10 minutes, the tire is too se­
ve rely damaged. Do not continue to drive.
Seek professional ass istance .
(D Tips
After a tire repair, have the sealant bottle
replaced at a dealership. This restores full
funct iona lity to the Tire Mobility System.
-
•
•

230 Fuses and bulbs
-No. Equipment
24 Transmission (control unit)
25 Heater rear
window Coupe/
heated rear window Roadster
26 Driver's side power window
27 Passenger's side power window
28 Not used
29 Washer pump
30 Cigarette lighter
31 Starter
32 Steering column module
33 Instrument cluster
34 Radio navigation system, radio
35 Audio amplifier
36 Engine (control unit)
37 CAN (Gateway)
38 Cigarette lighter
39 Not used
40
------------4 l Not used
42
43 Not used
44
45 Not used
46
47 SOARS tuner, cell phone pack-
age, TV tuner
48
49 Not used
Fuse location, left side of engine
compartment Amps
15
30/20
30
30
-15
20
40 5
5
20/15
30
10 5
20
-
-
5
5
Fig. 167 Illust ration of fuse holder on left side of en·
gine compartment: fuses (without fuse cover)
Some of the equipment items listed are op-
t ional or only available on certain model con-
figurations.
Note that the following table is accurate at
the time of going to press and is subject to
change.
No. Equipment Amps
Fuse holder (black)
1 Not used
-2 Not used
3 Not used
4 Not used
Anti-theft warning system (sen-
'
5 sor), anti-theft warning system 5
(horn)
6 Headlamp
washer system
30
Electric fuel pumps (supply),
7 volume control valve/Interrelais 15/10 (5-cyl.)
8 Windshield wipers
30
9 Heated seats (driver and pas-
25
senger)
10 Lumbar
support (driver and
10
passenger)
11 Not used
12 Ventilation blower 40
Fuse holder (brown)
1 Not used
2 Electric fuel pump (5-cyl.) 30
3 Not used
Relay coil relay volume control
5 valve (4-cyl.)/02 sensors (5- 5/10
7 cyl.)
02 sensors
Positioning valves pre-wired en­
gine harness
Ignition coils
9 Engine (control unit)
10 Water pump delayed-off 10
10
20
25 10 ..,_.

No. Equipment Amps
11 Feed (brake peda l) 5
-
12 Activated charcoal filter/charge I pressure control valve 10
Bulbs
Replacing light bulbs
For your safety, we recommend that you have
your authori zed Audi dealer replace burned
out bulbs for you .
It is becoming increasingly more and more
difficult to replace vehicle light bulbs since in
many cases, other parts of the car must first
be removed before you are able to get to the
bulb . Th is appl ies especially to the l ight bulbs
in the front of your car which you can only
reac h through the engine compartment.
Sheet metal and bulb holders can have sharp
edges that can cause ser ious cuts, and parts
must be correctly taken apart and then prop­
e rly put back together to help p revent break­
age of parts and long term damage from wa­
ter that can enter housings that have not been properly resealed.
F or your safety, we recommend that you have
your author ized Audi dealer replace any bu lbs
for you, since your dealer has the p roper tools,
the correct b ulbs and the expertise.
Ga s di sc harg e lamp s (Xeno n light s}*:
Due to the high electrical voltage, have the
bulbs replaced by a qualified technician.
Headlights with Xenon light can be identified
by the high voltage sticker.
A WARNING
Contact with high-voltage components of
t he electrical system and improper re­
placement of gas discharge (Xenon) head­
light bulbs can cause serious personal in­
jury and death .
- Xenon bulbs are pressurized and can ex­
plode when being changed.
Fu ses and bulb s 231
-Changing Xenon lamps requires the spe­
cial tra ining, instructions and equip­
ment.
- On ly an authorized Audi dealer or other
qualif ied workshop should change the
bulbs in gas discharge lamps .
A WARNING .,.;
There are parts with sharp edges on the
openings and on the bulb holders that can
cause serious c uts.
- If you are uncertain about what to do,
have the work performed by an a uthor­
ized Audi dealer or othe r qualified work­
shop. Ser ious personal in ju ry may result
from imprope rly performed work.
(D Tips
- If you must replace the light bulbs your­
self, a lways remember that the eng ine
c ompartment of any vehi cle is a hazard­
ous area to work in. A lways read and
heed all WARN INGS
~page 174, Engine
compartment ¢&, .
-It is best to ask your authorized Audi
dealer whenever yo u need to change a
bulb .
•
•
-

232 Emergency situations
Emergency situations
General
This chapter is intended for trained emer­
gency crews and working personnel who
have the necessary tools and equ ipment to
perform these ope rations.
Starting by pushing or
towing
Q;) Note
Vehicle s with an automati c transmission
cannot be started by pushing or towing .
Starting with jumper
cables
If necessary, the engine can be started by
connecting it to the battery of another vehi­
cle.
If the engine should fail to start because of a
discha rged or wea k batte ry, the battery can be
connected to the battery o f
another vehicle,
using a
pair of jumper cables to start the en­
g ine .
Jumper cables
Use only jumper cab les of sufficiently
large cross section to safely carry the starter
cur rent. Refer to the manufacturer's specifica­
ti ons.
Use on ly jumper cables which have
insulated
termina l clamps and are properly marked for
d istinction :
plus(+) cable in most cases colo red red
minu s(-) cable
in most cases colo red black .
_& WARNING
Batterie s contain elec trici ty, a cid, and ga s.
Any of th ese c an cause ve ry seri ous or f ata l
inju ry . Follow the instructions below fo r
safe han dling of your ve hicle's battery.
- Alw ays s hield yo ur eyes and avoid lean ­
ing over the batte ry w henever possib le . -
A discharged battery can a lready freeze
at temperatures just be low 32 °F (0 °C).
Before connect ing a jumper cab le, the
frozen battery must be thawed com­
p letely, othe rwise it cou ld explode .
- Do not allow batte ry acid to contact eyes
or skin . Fl ush any contacted a rea wi th
water immediat ely .
- Imp roper use of a booster battery to
s tart a vehicle may cause an explosion.
- Vehicle batter ies generate explosive gas­
es . Keep sparks, flame and lighted ciga­
rettes away from ba tte ries .
- Do not try to jump start a ny ve hicle w ith
a low ac id leve l in the battery .
- The vo ltage of the booster batte ry m ust
a lso have a 12-Vo lt rat ing . The capacity
(A h) of the booster batte ry should not b e
lowe r than that of the discharged bat­
tery . U se o f batt erie s of d iffe ren t voltage
or subs tanti ally diffe ren t "Ah" rat ing
may c ause an exp losion and person al in­
ju ry .
- N ever ch arge a fr ozen bat te ry. Gas t rap ­
ped in the ice may ca use an ex plosion .
- N ever ch arge o r use a batt ery th at has
been fro zen. T he battery case may have
be weakened.
- Us e of batt erie s of di ffere nt vo lta ge or
substan tially differen t ca pa city (Ah) rat ­
i ng may cause an exp losion and injury.
T he capac ity (Ah) of the booster battery
should not be lower than that of the dis­
charged batte ry.
- Before you check anything in the engine
compartment, always read and heed a ll
W ARNI NGS
c::;,page 174, Engine com­
partment .
@ Note
-App lying a hig her voltage booster ba t­
tery will cause expens ive damage to se n­
sitive electronic components, such as
cont ro l units , relays, rad io, etc.
- There must be no electrical contact be­
twee n the vehicles as otherwise current
cou ld already start to flow as soo n as th e
posi tive (+) term inals are connect ed. ""

248 Index
Connecting ...... ..... ... .. .. .... . 190
Disconnecting . ....... ... .. .. .... . 190
Important warn ings . .... ... .. .... . 192
Locat ion 192
Low . .. .. .... ........... ........ . 156
Replacing the battery ......... .. ... 191
State of charge ..... .... .. .. .. .. .. . 156
W inte r operation .......... ... .. .. . 190
Working on the battery .. ...... .. .. . 192
Battery voltage ................ .... .. 19
Before driving . . . . . . . . . . . . . . . . . . . . . . . 90
Blended gasoline ........... ... .. .. . 176
Body cavity sealing . . . . . . . . . . . . . . . . . . 170
Boost . .. .. .. .. . .......... .. .. .... .. 28
Booster seats .............. ... .. .. . 138
Boost pressure indicator . ... .. .... .. . . 28
Brake fluid
Changing the brake flu id . .. .. .. .. .. .
190
Chec king the bra ke fluid level . .. .... . 189
What is the correct brake fl uid leve l? .. 189
What should I do if the brake fluid warn-
ing light comes on? .. ... .. .. ... ... .
189
Brake fl uid reservo ir ........ .. .. .... . 189
Brake system .............. .... .... . 189
Anti -lock brake system ........ .. .... 18
Brake ass ist system . .. .. .. .. .. .. .. . 150
Brake fl uid . ... .. ..... ... .. .. .. .. . 189
Brake flu id spec ifica tions for refill and re-
p la cemen t ... ......... .. .. .. .. .. .
190
Brake light defect ive . ... .. .. .... .. . . 20
Brake pads .. .. .. ..... ... .. .. .... . 159
General information . ... .. .. ... ... . 153
How does the moisture or road sa lt affect
the brakes? .............. .. .. .... .
153
Malfunc tio n . . . . . . . . . . . . . . . . . . . . . . . 14
Warn ing/ indicator l ights ....... .. .... 14
Worn brake pads symbol . . . . . . . . . . . . . 18
Break- in period ............ .. .. .. .. . 159
Brake pads ... ........... .. .. .... . 159
Tires
Bulbs
C
159
23 1
Califo rni a Proposit ion 65 Warning .. .. . 18 1
Battery specif ic .. ..... ... .. .. .... . 193
Capac it ies . .. ..... ........... ... .. . 240
Car care . ... .... .. ... .. .. ... .... . .. 164
Interior . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Plastic and vinyl . .... .. ..... ... .. .. 168
Care of ex ter ior .. .. ............. .. .. 164
Cargo area
refer to Luggage compartment ....... . 96
Cata lytic co nverter ... ... ..... ... .. .. 160
CD cha nger . .... .. ............. .... . 64
Certification . . . . . . . . . . . . . . . . . . . . . . . 246
Chang ing a flat t ire ... ... ..... ... .. .. 224
Chang ing engine oil ................ . 186
Chassis
Undercoating .. .. ............. .. ..
170
also refer to Audi magnet ic r ide .. .. .. . 78
Checking
Battery ac id leve l ... ... ..... ... .. ..
193
Engine coolant level . . . . . . . . . . . . . . . . 187
Checking t ire press ure ........... .. .. 2 02
Child restraint
Danger of using child rest raints in the
front seat . ...... ................ .
110
Child restraints
Where can I get additional informat ion
about child restraints and the ir use? ..
149
Child restraint system anchors . ... .. .. 143
Child saf ety . .. .. .. .. .. ...... ... .. .. 130
Co nvertib le loc king retractor ... .. .... 140
G ui dance fixtures for lower anc ho rages 1 4 5
Important sa fe ty instru ctions for using
child safety seats ... .... .... ... .. ..
133
Important things to know whe n driving
with children .... ............... ..
130
Installing a c hild restra int using the
LATCH system . . . . . . . . . . . . . . . . . . . . .
146
Mounting and releasing the anchorage
hook ...... ... .. .. ... ....... .... .
146
Tether anchors . .. ............. .... 14 7
Tether straps .. .. ............. .... 14 7
Child safety seat ..... ... ..... ... .. .. 135
Co nvertib le locking retractor ......... 140
Installing ... .. .. ... .. .. ... ..... .. 140
U nused safety be lts on the rear seat 135
Child safety seats
Booster seats .... ............... ..
138
Co nvertib le child seats ............ . 136
How do I properly i nstall a child safety
. h" l ? 133 seat in my ve 1c e .............. .. . .