display AUDI TT COUPE 2014 Owners Manual

Downloaded from www.Manualslib.com manuals search engine 0
N The
positions of the engine oil dipstick and en­
gine oil filler cap ¢Fig. 211 (items @and @)
may be different on some engine versions.
Engine oil
Choosing the correct engine oil grade
The service interval display in the instrument
cluster of your vehicle will inform you when it is
time for an oil change. We recommend having
the oil changed by a qualified workshop.
If you have to top up the oil between oil changes,
use the grades of oil specified in the table in ac­
cordance with VW standards. You will need to
know whether
- the vehicle is being serviced based on the flexi­
ble or fixed oil change service (see Last service
record in Service Schedule).
- the vehicle has a petrol or diesel engine (see
sticker on inside of fuel tank flap).
- a diesel particulate filter is fitted on the vehicle
(see Delivery Inspection section of Service
Schedule).
Oil Change Serv-
Oil Change Serv-
ice (flexible)
ice (fixed)
Petrol VW50400 vw
502 00
engine Alternatively:
vw 504 ooa)
Diesel VW50700 With
diesel par-
engine ticulate
filter:
VW 507 00
Without diesel
particulate filter:
vw 505 01
Alternatively: vw 507 oob
>
al When using fuel complying with EN 228 or DIN 51626-1
b) When using fuel complying with EN 590 or DIN 51628
CD} Note
If the oil grades specified in the table are not
available, you can use one of the following
....
� grades
as a substitute. To prevent damage to
� the
engine, this should not be done more
.... Checking
and topping up fluids
than once between oil changes and no more
than 0.5 Litres should be used.
- Petrol engines: ACEA A3 or API SN (API SM)
standard
- Diesel engines: ACEA C3 or API CJ-4 stand­
ard
(©) Note
- For China: Only oil complying with VW
standard 502 00 with viscosity SAE 5W-40
may be used on vehicles with a petrol en-
gine.
- The flexible oil change service is not availa­
ble in all countries.
Checking the engine oil level
Fig. 212 Guide for oil dipstick
Checking oil level
.,. Park your vehicle on a Level surface.
.,. Allow the warm engine to run briefly at idling
speed and then switch off the ignition.
.,. Wait approx. two minutes.
.,. Pull out the dipstick. Wipe the dipstick with a
clean cloth and insert it again, pushing it in as
far as it will go.
.,. Then pull the dipstick out again and check the
oil level ¢ Fig. 212. If the oi L Level is too Low,
add more engine oil¢ page 224.
Oil level in area 0
.,. Do not top up oil.
Oil level in area @
.,. Oil can be topped up. After topping up the oil (£)
(£)
N
0
co
(Il
Level should be in area 0·
..,
223

Downloaded from www.Manualslib.com manuals search engine Checking
and topping up fluids
Oil level in area @
.. Oil
must be topped up. After topping up the oil
Level should be in area 0-
Depending on how you drive and the conditions
in which the car is used, oil consumption can be
up to 0.5 Ltr./1000 km. Oil consumption is Likely
to be higher for the first 5000 km. For this rea­
son the engine oil Level must be checked at regu­
lar intervals, preferably when filling the tank and
before a journey.
Topping up the engine oil "t::r.
Fig. 213 Engine compartment: Engine oil filler cap
.. Switch off the engine.
.. Unscrew cap� from oil filler opening
¢Fig. 213, ¢page 222, Fig. 211.
.. Carefully
add 0.5 Litres of suitable oil
¢page 223. 0
N
N
(X)
cc
.. After two minutes check the oil Level once again
¢ page 223, Checking the engine oil Level.
.. If
the oil Level is too Low, add more engine oil.
.. Replace the oil filler cap carefully and push the
dipstick all the way in.
_& WARNING
- Ensure that no oil comes into contact with
hot engine components when topping up:
this could cause a fire.
- Wash your skin thoroughly if it comes into
contact with engine oil.
CD CAUTION
- The oil Level must never be above area 0, as
this may result in damage to the catalytic
converter or to the engine. Contact a qua Li-
224 fied
workshop to extract the engine oil if
necessary
- No additives should be used with engine oil.
Any damage caused by the use of such addi­
tives would not be covered by the factory
warranty.
@ For the sake of the environment
- Never pour oil down drains or into the
ground.
- Always observe statutory requirements
when disposing of empty oil canisters.
Cooling system
Coolant
The engine cooling system is filled at the factory
with a mixture of conditioned water and coolant
additive. This coolant must not be changed.
The coolant Level is monitored via a warning Lamp
on the infotainment display ¢page 12. However,
we re com mend that it shou Ld be checked occa­
sionally.
If you do need to top up the coolant, use a mix­
ture of water and coolant additive. We recom­
mend mixing coolant additive with distilled wa­
ter .
Coolant additive
The coolant additive contains anti-freeze and cor­
rosion protection agent. Only use one of the fol­
lowing coolant additives. It is possible to mix
these additives.
Coolant additive Specification
G12++ TL
774 G
G13 TL
774 J
Only if the above
grades are not availa- TL
774 F
ble: G12+
The amount of coolant additive which needs to
be mixed with the water depends on the temper­
atures to be expected in the winter season. If the
anti-freeze concentration is too Low, the coolant
can freeze and cause engine damage.

Downloaded from www.Manualslib.com manuals search engine Checking
and topping up fluids
Brake fluid
&
8cm DOT 4 0
0
Fig. 215 Engine compartment: Cap of brake fluid reservoir
Checking brake fluid level
The brake fluid Level must be between the MIN
and MAX marks on the reservoir ¢ page 222,
Fig. 211.
If the Level goes down noticeably in a short time,
or drops below the MIN mark, there may be a
Leak in the brake system. Obtain professional as­
sistance. The brake fluid Level is also monitored
via a warning Lamp on the infotainment display
¢page 11.
In right-hand drive vehicles the brake fluid reser­
voir is on the other side of the engine compart­
ment.
Changing brake fluid
Your vehicle's Service Schedule will tell you the
regular intervals at which the brake fluid is due
for renewal. We recommend that you have the
brake fluid changed by a qualified workshop dur­
ing a service.
A WARNING
- Brake fluid is poisonous; it must be stored in
the sealed original container in a safe place
out of the reach of children.
- Heavy use of the brakes may cause a vapour
Lock if the brake fluid is left in the system
for too Long. This would seriously affect the
efficiency of the brakes and the safety of the
car -risk of accident!
226 CD
CAUTION
Brake fluid must not be allowed to come into
contact with the vehicle's body, otherwise it
will attack the paintwork.
Battery General notes
ALL work on batteries requires specialist knowl­
edge.
The battery is virtually maintenance-free. It is
checked as part of the Inspection Service.
When an airbag is triggered, the battery will, un­
der certain circumstances, be disconnected from
the on-board power supply for safety reasons
¢ .&.. in General notes on airbag system on
page 209.
Disconnecting the battery
The battery should always be Left connected. If
the battery is disconnected, some of the vehicle's
functions will become inoperative (e.g. electric
windows). These functions will require resetting
after the battery is reconnected. For this reason,
the battery should only be disconnected from the
vehicle's electrical system when absolutely nec­
essary.
If the vehi cle is not used for long periods
If you do not drive your vehicle for a period of
several days or weeks, the power management
will gradually shut off the on-board systems one
by one, or reduce the amount of current they are
using. This Limits the amount of power consumed
and helps to ensure reliable starting even after a
Long period ¢ page 106. Certain convenience fea­
tures, such as interior Lighting or electric seat ad­
justment, may not be available. These functions
will be restored when you switch on the ignition
and start the engine. Even though some systems
are deactivated automatically, certain electrical
equipment continues to draw current even when
the ignition is off. If the vehicle is Left standing
for several months, this can result in total bat-
tery discharge. If the battery is allowed to dis­
charge completely, an internal chemical reaction
..,_

Downloaded from www.Manualslib.com manuals search engine 0
N
co
....
\D L/'l
N
L/'l
.... the
battery, we recommend that the replacement
battery used is of the same make and type as the
original-equipment battery. After changing the
battery, the power management system must be
initialised by a qualified workshop to ensure that
the replacement battery is charged to an opti­
mum level.
A replacement battery must have the same ca­
pacity, voltage (12 V) and current rating. It must
also have the same dimensions as the original,
factory-fitted battery and have sealed caps. The
battery must comply with the standards
TL 825 06 (dated April 2008 or later) and
VW 7 50 73 (April 2010 or later).
Since the battery is difficult to access, we recom­
mend having it replaced by an Audi dealer or
qualified workshop.
CD CAUTION
- Your vehicle is equipped with a special deep
cycle battery (e.g. AGM type). The on-board
electronic systems may develop problems if
you fit a different type of battery. For this
reason, if you need to replace the vehicle
battery, make sure that the specifications of
the new battery match the original exactly.
- Make sure that the vent hose is always at­
tached to the original opening on the side of
the battery. Gases or battery acid can other­
wise escape and possibly cause damage.
- The battery holder and clamps must always
be correctly secured.
- Before starting any work on the battery, al­
ways observe the warnings listed under
¢ page 227, Important safety warnings for
handling a car battery.
@ For the sake of the environment
"S Batteries contain toxic substances including
sulphuric acid and lead. They must be dis­
posed of appropriately and must not be put
together with ordinary household waste.
Make sure the battery removed from the vehi­
cle cannot tip over. Otherwise, sulphuric acid
could escape. Checking
and topping up fluids
Windscreen washer
N
N
co
al
Fig. 217 Engine compartment: Cap of windscreen washer
container
The container for the windscreen washer Q con­
tains the cleaning fluid for the windscreen and
the headlight washer system* ¢ Fig. 217,
¢page 222, Fig. 211. Container capacity
¢page 258.
Clean water should be used when topping up. If
possible, use soft water to prevent scaling on the
washer jets. Always add washer fluid to the water
(with anti-freeze additive in winter).
CD CAUTION
- Never put in radiator anti-freeze or other
additives.
- Never use washer fluid which contains paint
thinners or solvents as it can damage the
paintwork.
Service interval display
The service interval display detects when the
next service is due for your vehicle.
Fig. 218 Instrument cluster display: Service interval dis­
play (example)
There are two service interval display levels:
229

Downloaded from www.Manualslib.com manuals search engine Checking
and topping up fluids
- Inspection or oil change reminder: After acer­
tain mileage, a service reminder will appear on
the infotainment display each time the ignition
is switched on/off¢ Fig. 218. The distance or
time remaining will be shown briefly.
- Inspection or oil change due: When your vehi­
cle is due for an inspection, oil change or both,
the corresponding reminder Inspection due!,
Oil change due! or Oil change and inspection
due! will appear briefly after you switch the ig­
nition on/off.
Checking the service intervals
You can look up the distance and time remaining
until the next oil change and next service inspec­
tion. Select the following on the infotainment
system: I MENU I button > Car > left control button
> Se rvicing & checks > Service intervals. You can­
not check the service interval for the first 500 km
or so after resetting the display or when your ve­
hicle is new.
CD CAUTION
- Keeping to the correct service intervals is
most important for the service life and re­
sidual value of the vehicle (and especially
for the life of the engine). Services must al­
ways be carried out promptly, even if the
mileage is low.
- The time until the next oil change is not
counted down if the battery is disconnec­
ted. If your vehicle is out of service for an
extended period, please refer to the Service
Schedule for details of the next service
date.
230

Downloaded from www.Manualslib.com manuals search engine 0
N
co
....
\D Lfl
N
Lfl
.... lamp
[Bl and a message on the infotainment dis­
play. If only one tyre is affected, the display will
indicate its position.
Each time you change a tyre, change the wheels
round or change the tyre pressures on your vehi­
cle (e.g. when switching from partial load to full
load and vice-versa), you must store the new tyre
pressures on the infotainment system
¢ page 235. Monitoring of the tyre pressures is
based on the tyre pressures you have stored. The
inflation pressures recommended for your vehicle
are given on the tyre pressure sticker
¢ page 233, Fig. 220.
The rolling circumference and vibration can
change and cause a tyre pressure warning if:
- The inflation pressure in one or more tyres is
too low.
- The tyre has suffered structural damage.
- The wheels were changed or the tyre pressures
were changed and the new tyre pressures were
not stored ¢ page 235.
- You are driving with the temporary spare
wheel*.
Indicator lamps
RI]- Loss of pressure on one or more tyres¢ A.
Check and change or repair the tyre(s). Check and
adjust the inflation pressures of all four tyres
again and store the new tyre pressures on the in­
fotainment system¢ page 235.
ffim (Tyre Pressure Monitoring System) Tyre
pressure: fault. See owner's manual -If� ap­
pears and the indicator lamp [Bl in the instru­
ment cluster display flashes for approx. one mi­
nute and then remains lit after you have switched
on the ignition or while you are driving, there is a
fault in the system. Try to store the correct tyre
pressures ¢ page 235. If the indicator lamp
does not go out or if it comes on again after a
short time, drive to a qualified workshop without
delay and have the fault rectified.
&_ WARNING
- If the tyre pressure loss indicator appears
on the display, slow down immediately and
avoid any severe braking or steering ma- Wheels
and tyres
noe uvres. As soon as you can do so safely,
stop and check the tyres and the tyre pres­
sures.
- It is the driver's responsibility to ensure that
the tyre pressures are correct. For this rea­
son you must check the tyre pressures regu­
larly.
- Under certain conditions (e.g. driving at
high speeds, on ice and snow or on poor
road surfaces) the tyre pressure loss indica­
tor may not appear immediately.
- Run-flat tyres* may only be used on vehicles
which were originally equipped with this
type of tyre.
- If a malfunction occurs in the ESC system,
the tyre pressure loss indicator may also be
out of action.
- When driving with snow chains, a system
malfunction can occur.
- The tyre pressure loss indicator on your Audi
is specially matched to tyres with the mark­
ing "AO" or "RO" ¢ page 231. We recom­
mend that you use these tyres.
Storing tyre pressure settings
Applies to vehicles: with tyre pressure loss indicator
When you change a tyre or the tyre pressure on
your vehicle, you must confirm the change on the
infotainment system.
� Before storing the new tyre pressures, check
that the current pressures on all four wheels
correspond to the specified values and adapt
the pressures to the current load ¢ page 232.
� Switch on the ignition.
� Select the
following on the infotainment sys­
tem: I MENU I button >Car> left control button
> Servicing & checks > Tyre pressure loss indi­
cator.
@ Note
Do not store the tyre pressures if you are driv­
ing with snow chains. Otherwise, a system
malfunction may occur .
235

Downloaded from www.Manualslib.com manuals search engine Care
of vehicle and cleaning
Component Situation Remedy
Paintwork Paint damage Refer
to the vehicle data sticker for the paint no. and touch
up using a paint pen¢ page 257
Fuel overflow
Rinse with water without delay
Surface rust Surface rust remover, apply wax afterwards; contact your
qualified workshop with any questions
Corrosion Have
it removed by your qualified workshop
Water no longer
Apply wax (at least twice a year)
pearls off clean paint-
work
Paint has lost its Treat
with a suitable polish; finish with wax coating if pol-
shine, gloss cannot
ish does not contain wax compounds
be restored by waxing
Residues, e.g. insects,
Remove immediately using water and a micro-fibre cloth
bird droppings, resin-
ous tree sap, road salt
Fat-based stains, e.g.
Remove immediately using mild detergent a
>
and a soft
cosmetics or sun lo- cloth
tion
Carbon parts Dir
t/deposits
Interior: Same treatment as plastic parts
Exterior: Same treatment as painted parts
a) Mild detergent: not more than two tablespoons of pH-neutral detergent to one litre of water
Cleaning the interior
Component Situation Remedy
Windows Dirt/deposits Glass
cleaning agent, then wipe dry
Ornamental trim/ Dirt/deposits
Mild detergent a
>
mouldings
Plastic parts Dirt/deposits
Damp cloth
Heavier dirt/deposits Mild
detergent a
>
; solvent-free plastic cleaning
agent if necessary
Displays/instru- Dirt/deposits
Soft cloth with LCD cleaner; dust deposits in the
ment cluster lower
area of the instrument cluster can be re-
moved with a soft brush.
Controls and dis- Dirt/deposits
Soft brush, then soft sponge with mild detergent a
>
plays Seat belts Dirt/deposits
Mild detergent a
>
(allow to dry before retracting)
238

Downloaded from www.Manualslib.com manuals search engine 0
N
co
....
\D L/'l
N
L/'l
.... ,&.
WARNING
Never attempt to repair a fuse or replace a
blown fuse by fitting a fuse with a higher am­
pere rating. This could damage the electrical
system -risk of fire!
CD CAUTION
If a newly replaced fuse blows again after a
short time, the electrical system must be
checked by a qualified workshop as soon as
possible.
@ Note
- Unassigned fuse locations are not shown in
the tables below.
- Some of the items of equipment listed in
the tables below are only fitted on certain
models or are optional extras.
Fuses in vehicle interior
Fig. 246 Interior: Fuse layout
No. Electrical
equipment
F3 ESC
control unit
F4 Central computer (MIB-2)
FS Gateway No.
F6
F7
F8 F9
FlO Fll
F12
F13
F14
FlS
F16
F17
F18
Fl9
F20
F23
F25
F26
F28
F29
F31
F32 F33
F34
F35
F36 F37
F38 F39 Fuses
and bulbs
Electrical equipment
Anti-theft alarm system
Air conditioner console, selector lever (au-
tomatic gearbox), auxiliary heating, relay
coil for rear window heating
Diagnostics, switch for electronic parking
brake, light switch, rain/light sensor, inte-
rior lighting
Steering column switch module
Display
Haldex coupling
MMI system
Control unit for suspension control
Air conditioner blower
Electric steering column lock
MMI system
Instrument cluster
Reversing camera
Control unit for convenience key system
Electric lumbar support adjuster
Exterior lighting (right side), on-board
computer (right side)
Door/s, driver's side (e.g. electric windows)
Seat heating
Media socket for AMI High
On-board computer
On-board computer (left side)
Driver assistance systems
Airbag Electrical socket relay, interior sound, re-
versing light switch, temperature sensor,
oil level sensor
Diagnostics, headlight range control, air
quality sensor, automatic anti-dazzle mir-
rors
Corn ering light (right side)/ LED headlight
(right side)
Cornering light (left side) / LED headlight
(left side)
Engine control unit, ESC control unit
Door(s), passenger's side (e.g. electric win-
dows)
255

Downloaded from www.Manualslib.com manuals search engine Accessories
and modifications to the vehicle
Device Text message
Possible reme-
dy
Infotainment Some
func-
Switch on the
display tions
of the in-
ignition. If the
fotainment component
system are cur- protection is
rently unavail- still not deacti-
able. Please vated, contact
switch on the a
qualified
ignition. workshop.
Environmental compati­
bility
Environmental protection is a top priority in the
design, choice of materials and production of
your new Audi.
Design measures for economical recycling
- Modular construction to facilitate dismantling
- Plastic parts and elastomers are labelled in ac-
cor dance with ISO 1043, ISO 11469 and ISO
1629
Choice of materials
- Nearly all materials used can be recycled
- Similar types of plastics grouped together for
easy recycling
- Recycled materials used in manufacture
- Reduced vapour emissions from plastics
- CFC-free refrigerant in air conditioner
Compliance with the laws prohibiting the use of:
Cadmium, asbestos, lead, mercury , chrome VI
and other substances such as flame retardants
and plasticisers.
Manufacturing methods
- Using recycling material for manufacturing
plastic parts
- Solvent-free cavity sealing
- Solvent-free wax for protecting the vehicles in
transit
- Solvent-free adhesives
- No CFCs used in production
- Surplus materials used extensively for energy
conversion and building materials
- Overall water consumption reduced
262 -
Heat recovery systems
- Water-soluble paint

Downloaded from www.Manualslib.com manuals search engine Numbers
and
Symbols
360 °
display . . . . . . . . . . . . . . . . . . . . . . . . . .
94
A
A/C (automatic air conditioner) . . . . . . . . . . .
55
A/C (manual air conditioner) . . . . . . . . . . . . . 54
ABS see Anti-Lock brake system 102
Accelerator pedal . . . . . . . . . . . . . . . . . . . . . 200
Accepting an entry suggestion . . . . . . . . . . 114
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . .
260
Active Lane assist . . . . . . . . . . . . . . . . . . . . . .
84
Driver messages . . . . . . . . . . . . . . . . . . . . . .
86
Indicator Lamp . . . . . . . . . . . . . . . . . . . . . . .
85
Setting steering vibration . . . . . . . . . . . . . .
87
Setting time of warning................
87
Switching on/off . . . . . . . . . . . . . . . . . . . . .
85
Adaptive Light Indicator lamp . . . . . . . . . . . . . . . . . . . . . . . 17
Adjusting volume
Multi-function steering wheel.. . . . . . .
20, 21
Airbag .............................. 209
Deactivating front passenger's airbag . . . 211
Front airbags . . . . . . . . . . . . . . . . . . . . . . . 210
Head-protection airbag . . . . . . . . . . . . . . . 215
Side airbags . . . . . . . . . . . . . . . . . . . . . . . . 214
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . 14
Air conditioner (automatic)
Adjusting air outlets . . . . . . . . . . . . . . . 55, 56
Air distribution, air outlets . . . . . . . . . . . . . 55
Air recirculation mode . . . . . . . . . . . . . . . . . 56
AUTO (automatic mode) . . . . . . . . . . . . . . . 55
Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55
Defrosting windows . . . . . . . . . . . . . . . . . . .
56
Drive select . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Key-coded settings . . . . . . . . . . . . . . . . . . . .
55
Rear window heating . . . . . . . . . . . . . . . . . .
56
Selecting temperature . . . . . . . . . . . . . . . . . 55
Air conditioner (manual) Adjusting air outlets . . . . . . . . . . . . . . . 54, 56
� Adjusting
temperature . . . . . . . . . . . . . . . . 54
� Air
distribution, air outlets . . . . . . . . . . . . . 54
,-j
� Air
recirculation
mode . . . . . . . . . . . . . . . . . 54
� Blower
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
,-j Index
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Defrosting windows . . . . . . . . . . . . . . . . . . . 54
Key-coded settings. . . . . . . . . . . . . . . . . . . . 53
Rear window heating . . . . . . . . . . . . . . . . . . 54
Air distribution, setting
Automatic air conditioner . . . . . . . . . . . . . .
55
Manual air conditioner . . . . . . . . . . . . . . . . .
54
Air outlets, adjusting . . . . . . . . . . . . . . . . . . .
56
Air recirculation mode
Automatic air conditioner . . . . . . . . . . . . . .
56
Manual air conditioner . . . . . . . . . . . . . . . . .
54
Alarm system
see Anti-theft alarm system . . . . . . . . . 25,
31
All-season tyres
see ALL-weather tyres . . . . . . . . . . . . . . . . .
233
All-weather Lights . . . . . . . . . . . . . . . . . . . . . . 3 7
All-weather tyres . . . . . . . . . . . . . . . . . . . . . 233
Alterations to the vehicle . . . . . . . . . . . . . . .
260
Alternative frequency (radio) . . . . . . . . . . . . 166
Alternative route . . . . . . . . . . . . . . . . . . . . . 155
Alternator (warning lamp) . . . . . . . . . . . . . . . 13
AMI see Audi music interface .......... 174,
175
Annou ncements (traffic programme) . . . . . 190
Anti-dazzle exterior mirrors . . . . . . . . . . . . . .
42
Anti-dazzle interior mirror . . . . . . . . . . . . . . .
42
Anti-freeze Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Winds creen washer system . . . . . . . . . . . . 229
Anti-lock brake system . . . . . . . . . . . . . . . . .
102
Anti-theft alarm system . . . . . . . . . . . . . . . . . 31
Anti-theft wheel bolts . . . . . . . . . . . . . . . . . 244
Armrest, front . . . . . . . . . . . . . . . . . . . . . . . . .
47
Ashtray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
A5R
see Traction control system . . . . . . . . . . . . 102
Assigning function to button (multi-function
steering wheel) . . . . . . . . . . . . . . . . . . . . . . . . 20
Audi connect . . . . . . . . . . . . . . . . . . . . . . . . .
137
Activating . . . . . . . . . . . . . . . . . . . . . . . . . .
137
Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . .
140
Configuring . . . . . . . . . . . . . . . . . . . . . . . .
143
Connecting a mobile phone . . . . . . . . . . . .
137
Connection settings . . . . . . . . . . . . . . . . . .
187
Data protection . . . . . . . . . . . . . . . . . . . . .
146
Functions . . . . . . . . . . . . . . . . . . . . . . . . . .
140
263