key AUDI TT ROADSTER 2016 User Guide

Downloaded from www.Manualslib.com manuals search engine 0
<t
0
N
,.....
N
....
0
,.....
Vl
CX) as
the windows cannot be opened from the
inside in an emergency.
(©) Note
- The windows can be operated for about ten
minutes after the ignition has been switch­
ed off. The window switches are only deacti­
vated when the driver&#39;s door or the passeng­
er&#39;s door is opened.
- When the doors are opened, or while the
soft top is being opened or closed, the win­
dows are automatically opened about
10mm.
Convenience open/close function
All the windows can be opened or closed at the
same time.
Convenience open function
&#34;&#34; Press and hold the� button on the remote
control key until all the windows have reached
the desired position.
Convenience close function
&#34;&#34; Press and hold the� button on the remote con-
trol key until all windows are closed ¢ ,& , or
Convenience close function with convenience
key*
&#34;&#34; Touch and keep your hand in contact with the
sensor* on the door handle until all the win­
dows and the soft top* are closed. Do not rest
your hand on the door handle while this is hap­
pening.
Adjusting settings for convenience open
function via infotainment system
&#34;&#34; Select the following on the infotainment sys­
tem: I MENU
I button
>Car> left control button
> Vehicle settings.
If you wish to use the convenience open function
for the windows, set Long press to open win­
dows to on. Doors
and windows
A WARNING
- Take care when closing the windows and the
soft top*. Careless or uncontrolled use can
cause injuries.
- For safety reasons, you should only use the
remote control key to open and close the
windows and soft top* when you are at least
2 metres away from the vehicle. To avoid in­
juries, always keep an eye on the windows
and the soft top* when pressing the I:@ but­
ton to close them. The windows and soft top
stop moving as soon as the I:@ button is re­
leased.
What to do after a malfunction
You can reactivate the one-touch open and close
function if it fails to operate.
&#34;&#34; Pull and hold the electric window switch until
the window is fully closed.
&#34;&#34; Release the switch and then pull it again for at
least one second.
Garage door opener
(Homelink)
Description
Applies to: vehicles with garage door opener (Homelink)
Fig. 27 Garage door opener: Examples of various devices
which can be activated
The garage door opener (Homelink) allows you
to activate garage doors, security systems, home
or office lighting and other electric devices by
means of control buttons inside your car. It com­
prises three buttons, integrated in the operating
unit above the interior mirror in the headliner, �
35

Downloaded from www.Manualslib.com manuals search engine Soft
top (folding roof)
� Note
- To avoid draining the vehicle battery, do not
operate the soft top repeatedly with the en­
gine switched off.
-A message will be displayed in the instru­
ment cluster if a soft top malfunction oc­
curs ¢ page 40.
- The soft top can also be operated manually
in the event of a malfunction ¢page 41,
Manual operation of the soft top. The cause
of the fault should be traced and rectified
by a qualified workshop as soon as possible.
- If you park the car with the soft top open,
remember that this leaves the interior ex­
posed to intruders and to potential damage
in sudden adverse weather. Lock any be­
longings you leave behind in the luggage
compartment. Close the soft top before you
leave the vehicle unattended.
- The windows in the doors are automatically
lowered slightly while the soft top is open­
ing/closing.
Convenience open/close function for soft
top
Fig. 31 Turning the key to activate the open and close
functions
Convenience open function at driver&#39;s door
lock
.. Press the@ button on the remote control key
to unlock the vehicle. .....
N
u..
a:,
.. Turn the key in the driver&#39;s door once to the un­
lock position CD ¢Fig. 31.
.. Within two seconds, turn the key a second
time and hold it in this position until the soft
top is fully open.
40 Convenience
close function at driver&#39;s door
lock
.. Turn the key in the driver&#39;s door once to the
lock position @¢ Fig. 31.
.. Within two seconds, turn the key a second
time and hold it in this position until the soft
top is completely closed.
The soft top stops moving immediately if you re­
lease the key. It is possible to operate this fea­
ture with the convenience key* up to a distance of
approximately 4 metres.
A WARNING
Please refer to the important safety notes
¢ A in Opening I closing the soft top on
page 39.
Driver messages
Soft top: operation not possible -
This message will appear if a malfunction occurs.
The soft top can be operated manually
¢page 41.
Soft top: operation currently not possible
If the soft top is operated repeatedly, the over­
load cut-off is activated for approx. 15 to 30 mi­
nutes. You can open/close the soft top again af­
ter this period.
Soft top: operation currently not possible.
Engine must be running
The power-operated soft top is deactivated if the
battery voltage is too low. You can open/close
the soft top again after starting the engine.
Soft top: operation currently not possible.
Outside temperature too low
The soft top cannot be opened at temperatures
below -15 °C.
Soft top: operation currently not possible.
Speed too high
For safety reasons, the power-operated soft top
cannot be opened at road speeds of over 50 km/
h. Reduce speed to open/close the soft top.
�

Downloaded from www.Manualslib.com manuals search engine Soft
top (folding roof)
Step 1: Raising the covers
Fig. 33 Covers closed
Fig. 34 Covers open
.., Disengage the push rod from the ball head
¢Fig. 33 .
.., Lift up the covers on both sides of the vehicle
¢Fig. 34.
Step 2: Releasing the soft top drive
Fig. 35 Luggage compartment: Tools for closing soft top
manually
42 Fig.
36 Driver&#39;s side: Hexagon key inserted
.., Open the boot lid.
.., Fold back the floor panel.
.., Remove the three plastic base panels
¢ page 58, Fig. 63 .
.., Take the screwdriver, the crank (D and the hex­
agon key@¢ Fig. 35 out of the vehicle&#39;s tool
kit
.., Insert the hexagon key in the screw and remove
the screw completely¢ Fig. 36. Then remove
the screw on the passenger&#39;s side.
Step 3: Closing the soft top
Fig. 37 Soft top in storage box
Fig. 38 Inside the front of the soft top: Removing the cov­
er
.., Lift the soft top out of the storage box ¢ ,&. .
.., Pull the soft top all the way up.
.,..

Downloaded from www.Manualslib.com manuals search engine Lights
and vision
[i]- Courtesy light position. The interior lights are
switched on and off automatically when this
function is activated.
It is no longer necessary to operate a switch to
turn on the reading lights. Simply swipe or tap
your finger on the light to switch it on or off. The
light can be dimmed by keeping your finger in
contact with the reading light after switching it
on.
Interior lights
Various optional lighting functions are available
for the vehicle interior. The settings for certain
functions can be adjusted on the infotainment
system. Select the following on the infotainment
system: I MENU I button > Car > left control but­
ton > Vehicle settings> Background lighting.
Instrument lighting
Fig. 44 Instrument lighting
The brightness of the lighting in the instrument
cluster and the centre console can be adjusted as
required.
.,. Briefly press the knob to release it.
.,. Turn the knob towards &#34;-&#34; or&#34;+&#34; to reduce or in­
crease the brightness of the lighting.
.,. Briefly press the knob again to engage it.
48 Clear
vision
Adjusting the exterior mirrors
Fig. 45 Driver&#39;s door: Adjuster knob for exterior mirrors
Turn the knob to the appropriate position:
Q/P - To adjust the exterior mirror (left or right
side). Move the knob in the desired direction.
(fill - To heat the mirrors (depends on the outside
temperature).
8 - To fold in the exterior mirrors*. One of the
infotainment settings allows you to control
whether or not the mirrors are folded in when
you lock the vehicle �page 31.
Tilt function for exterior mirror on passenger
side*
The mirror is tilted slightly to provide a better
view of the kerb when parking backwards. This
feature only works when the knob is in the posi­
tion for adjusting the mirror on the passenger
side.
You can adjust the tilted mirror surface by mov­
ing the knob in the desired direction. This new
position is automatically stored and assigned to
the remote control key when you take the car out
of reverse .
The mirror returns to its original position as soon
as you drive forwards at over 15 km/h or switch
off the ignition.
A WARNING
Convex or wide-angle* exterior mirrors give a
larger field of vision. However, they make ob-
jects look smaller and further away than they
�

Downloaded from www.Manualslib.com manuals search engine 0
<t
0
N
,.....
N
......
0
,.....
Vl
CX) Storage
Cup holders
Fig. 58 Cup holders
Fig. 59 Centre armrest raised: Cup holder*
Cup holder* underneath the centre armrest
&#34;&#34; Fold up the centre armrest ¢ page 55.
&#34;&#34;If necessary, fold back the plastic retainer
¢Fig. 59 .
.&_ WARNING
- Do not put any hot drinks in the cup holders
while the vehicle is moving. You could be
scalded if the hot liquid is spilt.
- Do not use cups, mugs or glasses made
from hard materials such as glass or porce­
lain. These could cause injury in the event of
an accident.
CD CAUTION
You should avoid putting open drinks contain­
ers in the cup holders. The drinks could other­
wise spill over and cause damage to e.g. the
electrical equipment or the seat covers. Seats
and storage
Further storage compartments
You will find several storage compartments and
retainers at various points in the vehicle:
- Storage compartments in the doors
- Storage compartment in the glove box. The
glove box can be locked with the emergency key
¢page 28.
- Storage compartment underneath the centre
armrest*
- Storage compartment at the front end of the
seats*. This compartment can hold objects
weighing up to 1 kg.
.&_ WARNING
- To avoid the risk of injuries, always keep the
glove box lid closed when driving.
- The storage compartments in the door trims
should only be used to store small objects.
Make sure that they are stored safely inside
the compartment, as otherwise they might
impair the protection offered by the side air­
bags.
Storage compartment between the
backrests
Fig. 60 Between the backrests: Storage compartment
&#34;&#34;To open the storage compartment, pull the
catch on the lid in the direction indicated (ar­
row) ¢ Fig. 60 and swivel the lid downwards.
&#34;&#34;To close the storage compartment, swivel the
lid upwards until it engages.
.&_ WARNING
To avoid the risk of injuries, always keep the
storage compartment lid closed when driving.
57

Downloaded from www.Manualslib.com manuals search engine Heating
and cooling
Heating and cooling
Air conditioner
Description
The air conditioner heats, cools and dehumidifies
the air inside the vehicle. It operates most effec­
tively with the windows closed. If the vehicle has
been standing in the sun, it may cool down faster
if you open the windows briefly to let the hot air
escape.
Pollution filter
The pollution filter removes impurities, such as
dust and pollen, from the air.
Key-coded settings
Certain settings will be automatically stored and
assigned to the remote control key in use.
® For the sake of the environment
If you wish to save fuel, switch off the cooling
mode on the air conditioner by pressing the
Controls for manual air conditioner
Applies to vehicles with manual air conditioner
Fig. 65 Manual air conditioner: Controls
The rotary controls and switches are used to con­
trol the functions. The LED in the corresponding
l l
May vary in different countries
60 !AIC!
button in the rotary control@. This will
also reduce emissions.
@ Note
- Keep the air intake slots in front of the
windscreen clear of snow, ice and leaves to
ensure unimpaired heating and cooling, and
to prevent the windows misting over.
- Condensation can drip off the air cooling
system and form a pool underneath the ve­
hicle. This is normal and does not indicate a
leak.
- If you notice, for instance, that the seat* or
rear window heating is not working, it may
have been temporarily switched off by the
power management function. These sys­
tems will be available again as soon as suffi­
cient electrical power is available.
@ Note
The air conditioner contains fluorinated
greenhouse gases. Further information is pro­
vided on a sticker in the engine compart­
ment 1
>.
button lights up when the function is switched
on.

Downloaded from www.Manualslib.com manuals search engine Heating
and cooling
The seat heating has three levels. The heat level
is indicated by an LED.
... To switch on the seat heating, press the� but­
ton once .
... To reduce the level, press the� button again .
... To switch off the seat heating, press the� but-
ton repeatedly until all the LEDs have gone out.
The seat heating automatically switches from
level 3 to level 2 after about 10 minutes.
When not to switch on the seat heating
Do not switch on the seat heating in the follow­
ing situations:
- Seat is unused
- A protective cover is fitted on the seat
- A child seat is fitted on the seat
- The seat is damp or wet
A WARNING
People with limited capacity to feel pain or
sense temperature could burn themselves
when using the seat heating. These people
must not use the seat heating -risk of injury!
CD CAUTION
To avoid damaging the heating elements of
the seat heating, please do not kneel on the
seat or apply sharp pressure at a single point.
Note
- The setting for the driver&#39;s seat heating is
assigned to the key in use.
- If the passenger&#39;s seat heating was on when
you last switched off the ignition, it will be
switched on automatically only if the igni­
tion is switched on again within 10 minutes.
64 Neck
heating
Applies to: vehicles with neck heating
The neck heating works when the engine is run­
ning.
Fig. 69 Driver&#39;s seat: Air outlets for neck heating
Fig. 70 Dashboard: Neck heating
The neck heating has three levels. The neck heat­
ing is switched on when you turn the knob clock­
wise ¢ Fig. 70. The LEDs above the seat symbol
indicate the blower level. To reduce the blower
level, turn the knob anti-clockwise. To switch off
the neck heating, turn the knob anti-clockwise
until all the LEDs have gone out.
The neck heating automatically switches from
level 3 to level 2 after about 6 minutes when the
soft top is closed.
A WARNING
- People with limited capacity to feel pain or
sense temperature could burn themselves
when using the neck heating. These people
must not use the neck heating -risk of in­
jury!
- If the air outlets in the seat ¢ Fig. 69 are
covered by items of clothing or similar while
the neck heating is on, the air that emerges
immediately afterwards can be very hot.
..,

Downloaded from www.Manualslib.com manuals search engine Starting
the engine
� Manual gearbox: Press the clutch pedal all the
way down and move the gear Lever into neutral.
� Vehicles with automatic gearbox: Press the
brake pedal and move the selector Lever to po­
sition P or N ¢ ,&..
� Press the ....,1s=
T_A_R _T_E_
N_G_I_N_ E-ST_O_PI
button. The
engine should start.
� Diesel engines can take a few seconds Longer
than usual to start on cold days. Please keep
your foot on the clutch pedal (manual gearbox)
or brake pedal (automatic gearbox) until the
engine starts. The indicator Lamp IJ Lights up
while the glow plugs are preheating.
If the engine fails to start immediately, the start­
er will be switched off automatically after a few
seconds. Try to start the engine again.
Start/stop system
Please note the information on ¢ page 71,
Start/stop sy
stem.
A WARNING
Never run the engine in confined spaces. The
exhaust gases are toxic -risk of poisoning!
CD CAUTION
Avoid high engine speeds, full throttle and ex­
treme load conditions until the engine has
reached its normal operating temperature;
otherwise this can damage the engine.
@) For the sake of the environment
Do not warm up the engine by running it with
the car stationary. You should drive off imme­
diately whenever possible. This will help avoid
unnecessary exhaust emissions.
ijj} Note
-Any noises which may be heard when the
engine is started are quite normal and no
cause for concern.
- If you leave the vehicle with the ignition
� switched
on, it will be switched off auto-
o
N
,.....
N
......
0
,.....
� 1}
This function is not available on all export versions. Driving
matically after a while. Please note that
electrical equipment such as the exterior
Lighting will also be switched off.
Switching off the engine
� Stop the vehicle.
� Vehicles with automatic gearbox: Move these­
lector Lever to position P.
� Press the !START
ENGINE STOP!
button
¢page 68, Fig. 72.
Steering lock1
)
The steering will be locked if you switch off the
engine with the !START
ENGINE STOP!
button,
move the selector lever to position P (on vehicles
with automatic gearbox*) and open the driver&#39;s
door.
The steering will be Locked if you switch off the
engine with the !START
ENGINE STOP!
button
and open the driver&#39;s door. The steering lock acts
as a theft deterrent.
Emergency Off function*
If necessary in an emergency, the engine can be
switched off while the vehicle is still moving at
speeds of 7 km/h and above. To switch off the
engine, press the !START E
NG I
N E
ST
OP!
button
twice in quick succession or hold it in for longer
than two seconds.
A WARNING
- Never switch off the engine until the vehicle
is stationary. Otherwise you may not have
the full benefit of the brake servo and pow­
er steering. You may need more strength to
steer and brake the vehicle than you nor­
mally would. This would mean a greater risk
of accidents and serious injury, because you
cannot steer and brake in the normal man­
ner.
- Always take the key with you when you leave
the vehicle. Otherwise the engine can be
started or power-operated equipment such
as the electric windows can be used. This
could result in serious injury.
liJI>
69

Downloaded from www.Manualslib.com manuals search engine Driving
CD CAUTION
If the engine has been working hard for a long
time, there is a risk of heat building up in the
engine compartment after the engine has
been switched off; this could cause engine
damage. For this reason, you should leave the
engine idling for about 2 minutes before
switching it off.
{(D Note
After the engine is stopped, the radiator fan
may remain on or turn itself back on for up to
10 minutes, even if the ignition is switched
off. This may occur for the following reasons:
- Residual heat has raised the coolant tem-
perature.
- Direct sunlight has additionally heated up
the engine compartment while the engine is
warm.
-Applies to vehicles with diesel particulate
filter: The emission control system is hot
because of the regeneration process, even
though the engine has not yet reached oper­
ating temperature.
Driver messages
Switch off ignition before leaving car. Battery is
being discharged
This message appears and the buzzer sounds if
you open the driver&#39;s door while the ignition is
switched on. Switch off the ignition to prevent
the battery from being discharged.
Pressing start/stop button again will switch off
engine.
This message appears if you press the
!START ENGINE STOP!
button while the vehicle is
moving.
Engine start system: fault. Please contact work­
shop
A fault has occurred when starting the engine au­
tomatically (automatic start function). Drive to a
qualified workshop soon and have the fault recti­
fied. Press and hold
the !START
ENGINE STOP!
button to start the engine.
70 II
Remote control key: hold back of key
against marked area. See owner&#39;s manual
This message appears if there is no convenience
key inside the vehicle or if the system cannot de­
tect or identify the key. This can happen, for ex­
ample, if the radio signal from the key is obstruc­
ted by a metal briefcase or similar, or if the key
battery is weak. Electronic equipment, such as
mobile phones, can also interfere with the radio
signal from the key.
The engine can still be started or stopped if this
happens (please refer to �page 71, Starting
the engine after a malfunction).
Ill Remote control key: key not recognised. Is
key still in vehicle?
If the indicator lamp Ill lights up and the mes­
sage appears, the convenience key was removed
from the vehicle while the engine was running. If
the convenience key is not in the vehicle you will
not be able to switch on the ignition or restart
the engine after it has been switched off. You will
also not be able to lock the vehicle from the out­
side.
Please press brake pedal
This message appears on vehicles with an auto­
matic gearbox if you try to start the engine with­
out first pressing the brake pedal.
Please press clutch pedal
This message appears on vehicles with a manual
gearbox if you try to start the engine without
first pressing the clutch pedal. The engine will
only start if you press the clutch pedal.
Please engage N or P
This message will appear if you try to start or
switch off the engine when the selector lever is
not in Nor P. The engine can then not be started
or switched off.
Shift to P, otherwise vehicle can roll away.
Doors do not lock if lever is not in P
For safety reasons, this message will appear and
a warning buzzer will sound if the selector lever
of the automatic gearbox is not in position P
when you switch off the ignition with the
�

Downloaded from www.Manualslib.com manuals search engine !START
E
NGIN E
STOP!
button. Put the selector
lever in position P; otherwise the vehicle can roll
away. If the lever is not in position P you will not
be able to lock the vehicle using the locking sen­
sor on the door handle or the convenience key.
Starting the engine after a malfunction
If the remote control key battery is exhausted or
if radio interference or a system malfunction oc­
curs, extra steps may be necessary in order to
start the engine.
Fig. 74 Steering column/remote control key: Starting the
engine after a malfunction
If the message t>>) Remote control key: hold back
of key against marked area. See owner&#39;s manual
is displayed, you can still start the engine man­
ually.
� Manual gearbox: Press the clutch pedal.
� Automatic gearbox: Press the brake pedal.
� Press the !START
ENGINE STOP!
button.
� Hold the remote control key against the symbol
y>>) ¢Fig. 74, as shown in the illustration. The
engine should start.
� If the engine does not start automatically,
press the !START
E
NGINE STOP!
button again.
@ Note
You can call up the driver message again by
pressing the !START
ENGINE STOP!
button.
Start/stop system Description
0 Applies
to: vehicles with start/stop system
� The start/stop system can help to save fuel and
8 reduce CO
2 emissions.
&#34;
Vl Driving
In start/stop mode, the engine is switched off
automatically when the vehicle stops, e.g. at
traffic lights. The ignition remains on during this
stop phase. The engine is automatically started
on demand.
The start/stop system is automatically activated
each time you switch on the ignition.
Basic conditions for start/stop mode
- The driver&#39;s door must be closed.
- The driver&#39;s seat belt must be buckled.
- The bonnet must be closed.
- The vehicle must have been moving at over 4
km/h since the last stop.
A WARNING
- Never switch off the engine until the vehicle
is stationary. Otherwise you may not have
the full benefit of the brake servo and pow­
er steering. You may need more strength to
steer and brake the vehicle than you nor­
mally would. This would mean a greater risk
of accidents and serious injury, because you
cannot steer and brake in the normal man­
ner.
- Always take the key with you when leaving
the vehicle -even if you only intend to be
gone for a short time. This is especially im­
portant if children are left in the car. They
might otherwise be able to start the engine
or use power-operated equipment such as
the electric windows -this could lead to in­
juries.
- To avoid injury, make sure that the start/
stop system is switched off before working
in the engine compartment ¢page 73.
CD CAUTION
Always switch off the start/stop system
¢page 73 before driving through water.
71