lock CADILLAC DEVILLE 1997 7.G Manual Online

Downloaded from www.Manualslib.com manuals search engine When you put the cap back on, turn it to the right
(clockwise) until you hear
a clicking sound. Make sure
you fully install the cap.
NOTICE:
If you need a new cap, be sure to get the right
type. Your dealer can get one
for you. If you get
the wrong type, it may not
fit or have proper
venting, and your fuel tank and emissions system
might be damaged.
Checking Thiw~s Under the Hood
A CAU I ION: I
r- - I
An electric fan under the hood can start up and
injure you even when the engine is not running.
Keep hands, clothing and tools away from any
underhood electric fan.
Things that burn can get on hot engine parts and
start a fire. These include liquids like gasoline,
oil, coolant, brake fluid, windshield washer and
other fluids, and plastic or rubber. You or others
could be burned. Be careful not to drop or spill
things that will burn onto a hot engine.
6-7
I

Downloaded from www.Manualslib.com manuals search engine Checking Engine Oil
111 out the dipstick and clean it with a paper towel or
cloth, then push it back in all the way. Remove it again,
keeping the tip down, and check the level.
When to Add Oil
If the oil is at or below the ADD line, then you’ll
need to add at least one quart of oil. But you must use
the right kind. This part explains what kind of oil to use.
For crankcase capacity, see “Capacities and
Specifications”
in the Index.
I NOTICE:
Don’t add too much oil. If your engine has so
much oil that the oil level gets above the upper
mark that shows the proper operating range,
your engine could be damaged.
The oil fill cap is located
behind the radiator on the
passenger’s side of the
engine. Turn the cap
counterclockwise to
remove it.
Be sure to fill it enough to put the level somewhere in
the proper operating range. Push the dipstick all the way
back in when you’re through.
6-11

Downloaded from www.Manualslib.com manuals search engine To get the right reading, the fluid should be at normal
operating temperature, which is 1
80 OF to 200 OF
(82°C to 93°C).
Get the vehicle warmed up by driving about
15 miles
(24
km) when outside temperatures are above 50°F
(10°C). If it's colder than 50°F (lO"C), you may
have to drive longer.
Checking the Fluid Level
Park your vehicle on a level place. Keep the
engine running.
With the parking brake applied, place the shift lever
in PARK
(P).
With your foot on the brake pedal, move the shift
lever through each gear range, pausing for about
three seconds in each range. Then, position the shift
lever in PARK (P).
0 Let the engine run at idle for three to five minutes. Then,
without shutting off the engine, follow
these steps:
1. The black transaxle fluid cap is located next to the
radiator hose and below the air cleaner assembly on the driver's side of the engine. Remove the air
cleaner assembly
so you can reach the transaxle fluid
cap. The assembly is attached to the vehicle by two
fasteners. Simply lift up on the air cleaner assembly
to remove
it. Find the transaxle fluid cap and turn it
counterclockwise to remove. Pull out the dipstick
and wipe it with a clean rag or paper towel.

Downloaded from www.Manualslib.com manuals search engine Checking Coolant
The surge tank is located next to the engine block on the
passenger’s side of the engine.
The cooling system
is under a lot of pressure when it is
hot.
If the CHECK COOLANT LEVEL message
appears on the DIC, you will need to add coolant.
”urning the surge tank pressure cap when the
engine and radiator are hot can allow steam and
scalding liquids to blow out and burn you badly.
Never turn the surge tank pressure cap
-- even a
little
-- when the engine and radiator are hot.
When your engine is cold, the coolant level should be at
the FULL COLD mark, which is
2.5 inches (6.4 cm)
below the base
of the fill neck. Use a flashlight as
necessary to see into the tank.
..... ......................... ................. ................... . ... ............ ............. ..I.. ... .................. ..................................... *....I. ...... . .”... ... ”.. ...... ...... .......... ....... ..... ................... ”
If this message comes on, it means you’re low on
engine coolant.
6-23

Downloaded from www.Manualslib.com manuals search engine A
2. Turn the headlamp housing socket counterclockwise
to unlock the socket from the lamp housing. 3. Disconnect the socket from the harness by separating
the locking
clip.
4. Install the new bulb and socket to the wiring harness
connector. Make sure that the harness is locked to the
bulb socket.
6-32

Downloaded from www.Manualslib.com manuals search engine Front Turn Signal Lamps
1. The turn signal lamps are located below the
headlamps.
To access, lift off the headlamp cover
(see Step
1 under “Headlamps”).
2. Turn the housing socket clockwise to unlock the
socket from the lamp housing.
3. Remove the turn signal
replace the bulb. lamp
housing socket and
6-36

Downloaded from www.Manualslib.com manuals search engine Center High-Mounted Stoplamp (CHMSL)
1. Lift the trim cover to remove.
2. Twist the socket counterclockwise and remove the
socket and bulb from the
housing.
3. Replace the bulb.
Reverse the steps to reassemble the stoplamp assembly.

Downloaded from www.Manualslib.com manuals search engine Rear Turn Signal Lamps and Taillamps
1. Loosen the upper Tom@ screw, but don't remove it.
2. Gently tilt the top portion of the lamp housing to
access the bulb sockets.
If you can't access the lower
bulb socket, remove the lamp housing completely.
I
3. Press the bulb socket housing lever and rotate the
socket counterclockwise to remove it.
6-38

Downloaded from www.Manualslib.com manuals search engine 4. Replace the bulb by pressing and turning it
counterclockwise.
5. Once you have installed the new bulb and socket into
the lamp housing, insert the tab on the lower portion
of the lamp housing first, then gently fit the rest of
the housing in place.
Windshield Wiper Blade Replacement
It’s a good idea to clean or replace the wiper blade
assembly on a regular basis or when worn. For proper
windshield wiper blade length and type, see “Normal Maintenance Replacement Parts” later in this section.
To
replace the wiper blade assembly:
1. Turn the ignition key to ACCESSORY and turn the wipers on. Position the wipers
on the windshield in
the
“mid” wipe position. Then with the door open,
turn the key to
OFF.
2. Insert a screwdriver into the slot as shown and press
down to release the wiper blade assembly.
3. Align the wiper arm pin with the hole on the wiper
blade assembly and snap it into place to install.
6-39

Downloaded from www.Manualslib.com manuals search engine MaxiF'usesIRelay Center
The MaxiFuses and relays are located next to the engine
compartment fuse block on the driver's side
of the
engine.
If a MaxiFuse should blow, have your vehicle
serviced by your Cadillac dealer immediately.
RELAY CENTER IDENTIFICATION
RELAY
Fuse
BODY 1
BODY 2
BODY 3
Usage
Real Time Dampening (RTD)
Fuse, Convenience Fuse, BATT
Fuse, Passenger and Driver Seat
Belt Comfort Solenoids, Trunk
and Fuel Door Release Solenoids
and Relays, Door Lock/Unlock
Relays, DPR Relay, Park Lamp
Relay, Right and Left Park Fuse,
Rear Fog Lamp Relay
Defog Relay, Pull-Down Fuse, Right and Left Heated Seat Fuse,
Electronic Level Control (ELC)
FuseRelay, Antenna Fuse, Heated
Mirror Fuse
Controlled Power Relay,
Controlled Power Back-up Relay,
Cluster Fuse, Platform Zone
Module (PZM) Fuse, Radio Fuse,
DAB Relay, Trunk and Fuel Door
Release Relay, High Beam Relay,
Comfort Fuse, Controlled Power
Relay, AMP Bose Only Fuse,
Right and Left Bose Relay