wipers CADILLAC DEVILLE 1998 7.G Owners Manual

Downloaded from www.Manualslib.com manuals search engine New Vehicle 66Break-In” Ignition Positions
NOTICE:
Your vehicle doesn’t need an elaborate
“break-in.” But it will perform better in the long
run
if you follow these guidelines:
0
e
0
Don’t drive at any one speed -- fast or
slow
-- for the first 500 miles (805 km).
Don’t make full-throttle starts.
Avoid making hard stops for the first
200 miles (322 km) or so. During this time
your new brake linings aren’t yet broken
in. Hard stops with new linings can mean
premature wear and earlier replacement.
Follow this breaking-in guideline every
time you get new brake linings.
Don’t tow
a trailer during break-in.
See “Towing
a Trailer’’ in the Index for
more information.
C
A E
With the ignition key in the ignition switch, you can turn
the switch to five different positions.
ACCESSORY (A): This position lets you use things
like the radio and the windshield wipers when the
engine is
off. To get into ACCESSORY, push in the key
and turn it toward you. The steering wheel will remain
locked, just as it was before you inserted the key.
2-18

Downloaded from www.Manualslib.com manuals search engine Flash-To-Pass Windshield Wipers
This lets you use the high-beam headlamps to signal the
driver in front
of you that you want to pass.
Pull the turn signal lever toward you to use. When
you do:
If the headlamps are either off or in the DRL mode,
the high-beam headlamps will turn on. They'll stay
on as long as you hold the lever there. Release the
lever to turn them
off.
If the headlamps are on low beam, they will shift to
high beam and stay there. Pull the lever toward you
to return to low beam.
a If the headlamps are on high beam, they will switch
to low beam. To return to high beam, pull the lever
toward you.
WIPER: Turn the band on the turn signal lever to
control
the wipers.
MIST: Turn the band toward you and then release it for
a single wiping cycle. For more cycles, hold the band
on
- MIST longer.
LO or HI: Turn the band away from you to either LO
(low speed) or to HI (high speed), depending on the
wiper speed you want.

Downloaded from www.Manualslib.com manuals search engine DELAY: You can set the wiper speed for a long or short
delay between wipes with this setting. Move the band to
the DELAY position. The closer you move it to
LO, the
shorter the delay. (DeVille Only)
OFF: Turn the band to OFF to turn off the wipers.
Be sure to clear ice and snow from the wiper blades
before using them.
If they’re frozen to the windshield,
carefully loosen or thaw them.
If the blades do become
damaged, get new blades or blade inserts.
Heavy snow or ice can overload the wiper motor. A
circuit breaker will stop the motor until it cools. Clear
away snow or ice to prevent an overload.
Rainsense Wipers (DeVille d’Elegance and
DeVille Concours Only)
This moisture sensor is mounted on the passenger’s
interior side
of the windshield behind the rearview
mirror and
is used to automatically operate the wipers
by monitoring the amount
of moisture that is on
the windshield. The Rainsense system can be activated by turning the
wiper stalk to one of the five sensitivity levels within the
AUTO DELAY area. The AUTO DELAY position
closest to
OFF is the lowest sensitivity setting. This
allows more water to collect on the windshield between
wipes. Rotating the stalk away from you to the other
AUTO DELAY settings increases the sensitivity
of the
system and frequency
of wipes. A single wipe will occur
each time you
turn the wiper stalk to a higher sensitivity
level.
An initial wipe occurs when you turn the ignition
on as a reminder that Rainsense is active. The windshield wipers
also remain in a “high park” position (the wipers
will stop on the windshield rather than their fully rested
position), even when the ignition is turned
off.
2-37

Downloaded from www.Manualslib.com manuals search engine The Rainsense wipers operate in a delay mode as well as
a continuous low or high speed depending on the
amount of moisture and the sensitivity level. The MIST
and “wash” cycles operate as normal and
are not
affected by the Rainsense function.
NOTICE:
The wipers must be turned off when going
through a car wash to avoid damage.
It is important to note that the Rainsense wiping feature
(AUTO
DELAY) can be overridden at any time by
manually changing the wiper control to
LO or HI speed.
Note that if you ever need
to replace the windshield,
make sure it is Rainsense compatible.
Windshield Washer
In freezing weather, don’t use your washer until
the windshield is warmed. Otherwise the washer
fluid can
form ice on the windshield, blocking
your vision.
At the top of the turn signaVmultifunction lever, there is
a paddle with the word PUSH on it. To spray washer
fluid
on the windshield, press and release this paddle.
The wipers will clear the windshield and either
stop or
return to your preset speed. For more washer cycles,
press and hold the paddle.
LOW WASHER FLUID will be displayed on the Driver
Information Center
(DIC) when the washer fluid reaches
a low level.
2-38

Downloaded from www.Manualslib.com manuals search engine Exterior Lamps
The control on the left side of the instrument
panel controls these
lamp systems:
0 Headlamps
0 Taillamps
Parking Lamps
0 Sidemarker Lamps
0 License Plate Lamp
Underhood Lamp
Fog Lamps (DeVille Concours Only)
Instrument Panel Lights
0 Interior Courtesy Lamps Pull the lamp control knob out to the
first stop to turn on
the parking and taillamps, sidemarker lamps and
instrument panel lights. Pull the knob out all the way to
turn
on the headlamps. Push the control knob all the way
back
in to turn the lamps and lights off.
Cluster lighting as well as instrument panel backlighting
will dim only when
it is dark outside.
Wiper Activated Headlamps
This feature activates the headlamps and parking lamps
after the windshield wipers have been in use for
approximately
20 seconds.
In order to operate the wiper activated headlamps, the
twilight sentinel must be turned on. This feature lights
the way in poor weather and it also makes your vehicle
more visible to other drivers. If the wiper activated
headlamps are on, and the ignition switch is turned off,
the wiper activated headlamps will immediately turn
off.
The wiper activated headlamps will deactivate if you
turn
off the twilight sentinel or if the windshield wipers
have been turned
off for a period of one or two seconds.
2-42

Downloaded from www.Manualslib.com manuals search engine Windshield Wiper Blade
Replacement
It’s a good iaea to clean or replace the wiper blade
assembly on a regular basis or when worn. For proper
windshield wiper blade length and type, see “Normal
Maintenance Replacement Parts” later in this section.
To replace the wiper blade assembly:
1. Turn the ignition to ACCESSORY and turn the
wipers on. Position the wipers on the windshield in
the
“mid” wipe position. Then with the door open,
turn the ignition to
OFF.
2. Insert a screwdriver into the slot as shown and press
down to release the wiper blade assembly.
3. Align the wiper arm pin with the hole on the wiper
blade assembly and snap it into place to install.
Headlamp Aiming
Your vehicle has the composite headlamp system. These
headlamps have horizontal and vertical aim indicators.
The
aim has been pre-set at the factory and should need
no further adjustment.
If your vehicle is damaged in an accident and the
headlamp aim seems to be affected, see your dealer.
Headlamps on damaged vehicles may require
recalibration of the horizontal aim by your dealer.
To check the aim, the vehicle should be properly
prepared as follows:
Place the vehicle on a level pad or surface.
The vehicle should not have any snow, ice or mud
The vehicle should be fully assembled and all other
work stopped while headlamp aiming is being done.
attached to it.
6-38

Downloaded from www.Manualslib.com manuals search engine Headlamp Wiring
The headlamp wiring has an individual fuse which is
powered by a MaxiFuse?
An electrical overload will
cause the lamps to go on and
off, or in some cases to
remain
off. If this happens, have the headlamp wiring
checked right away.
MaxiFuse
is a registered trademark of Little Fuse ,
Incorporated.
Windshield Wiper Fuses
The windshield wiper motor is powered by a MaxiFuse.
If the motor overheats due to heavy snow, etc., the
wipers will stop until the motor cools.
If the overload,
is caused by some electrical problem, be sure to have
it fmed.
Power Windows and Other Power Options
Circuit breakers protect the power windows and other
power accessories. When the current load
is too heavy,
the cifcuit breaker opens and closes, protecting the circuit until the problem
is fixed or goes away.
MaxiFusesLRelay Center
The MaxiFuses and relays are located next to the engine
compartment fuse b1oc.k on the driver’s side
of the
engine.
To access the compartment fuse block, remove
the shroud cover.
If a MaxiFuse should blow, have your
vehicle serviced by your dealer immediately.
1GEi-j
(BODYPI
(BODY3)
[-I
(LAMPS)
(7)
[iGGG)
[sEATs]
IGN1 J
(F)
(BRAKESJ
[CooLS-l
p, RELAY
Q
STARTER

Downloaded from www.Manualslib.com manuals search engine Engine Compartment Fuse Block - COR LPS INT LPS CIG LTFI~ CIG LTR2
L HDLP Lo R HDLP LO L HDLP HI R HDLP HI
, HDLPS , I HAZARD I I STOP , I MIRROR , I DRL ,
IGN O(ENG) WIPERS
FUSE CENTER IDENTIFICATION
AJC COMP PCM(BAT) PARKIREV
000 AIC COMP RELAY , ECS I IPCM(IGN)I , DIS ,
CRUISE
RELAY
The fuse block is located next to the air cleaner on the
driver’s side of the engine. Lift the cover to gain access.
Fuse
DRL
COR LPS
Usage
Daytime Running Lamps
Cornering Lamp Switch, Right and
Left Cornering Lamps, Right and
Left Position Lamp Relays (Export)

Downloaded from www.Manualslib.com manuals search engine Fuse
IGN- 1
WIPERS
A/C COMP
PCM (BAT)*
PARKREV
ECS*
Usage
Rear Ignition- 1 Relay, Fog Lamp
Relays (DeVille Concours Only),
Control Power Back-up, DlU
Relay, Ignition Switch in Steering
Column, Injectors, ECS Fuse, PCM
Fuse, DIS Fuse
Accessory Relay, Wiper Switch
AC Compressor Relay, Cooling Fan
Relays 1,2,3, Compressor Clutch
PCM
TCC and Exterior Travel Brake
Switch, Reverse Relay, Right and
Left Back-up Lamps,
Electrochromic Mirror (in Header),
Park Relay, Brake Transaxle-Shift
Interlock (BTSI) Switch, BTSI, PZM
Transaxle Shift Solenoids, Mass
Airflow, Canister Purge, PCM,
Linear Exhaust Gas Recirculation (EGR), Front Ignition-
1 Relay
Fuse Usage
PCM (IGN)* Powertrain Control Module (PCM)
DIS*
CRUISE
INJ*
Electronic Ignition Control Module Stepper Motor Cruise Control,
Power Steering Pressure Switch, Low Refrigerant Pressure
Cutoff Switch
Injectors 1,4,6,7
INJ* Injectors 2, 3, 5, 8
FUEL PUMP* PCM, Fuel Pump Relay, Fuel Pump
FUEL PUMP* Fuel Pump
OXY SEN1 * Oxygen Sensor Front, CAT Front
Oxygen Sensor
OXY SEN2* Oxygen Sensor Rear, Catalytic Converter (CAT) Rear
0
xygen Sensor
* Do not alter OBD I1 related fuses or circuit breakers.
6-63

Downloaded from www.Manualslib.com manuals search engine Radio Personalization .......................... 3-36
Radio Reception
................................ 3-38
Radio Theft-Deterrent Feature
..................... 3-36
Radios
............................. 3.14.3.18. 3.22
Rain. Driving In
................................ 4-17
Rainsense Wipers
............................... 2-37
RAP
......................................... 2-19
ReadingLamps
................................ 2-47
Rear Compartment Fuse Block
....................... 6-64
Door Security Locks
........................... 2-6
Outside Seat Position
.......................... 1-3 1
Storage Armrest .............................. 2-55
Window Defogger
............................ 3-12
Rear
Turn Signal Lamp Bulb Replacement ........... 6-36
Rearview Mirrors
..................... 2-48,2-49, 2-52
Recirculation
............................... 3-5, 3-9
Reclining Front Seatbacks
......................... 1-4
Refrigerants, Air Conditioning
.................... 6-67
Fuel Door Release
............................. 6-6
Keyless Entry
................................. 2-7
Trunk Release ................................ 2- 11
Remote Recall Memory .......................... 2-93
Remove Key Message
........................... 2-86
Normal Maintenance Parts
...................... 6-67
Seatpassengers
.............................. 1-31
Towing
................................. 5-9, 5-13
Remote
Replacement Bulbs
...................................... 6-66
Wheel ...................................... 6-47
Replacing Safety Belts
........................... 1-53
Reporting Safety Defects
.................... 7-12, 7-13
Checking
................................... 1-53
Child
....................................... 1-37
Head
........................................ 1-5
Replacing
Parts After a Crash ................... 1-53
Retained Accessory Power
........................ 2-19
Reverse, Automatic Transaxle
..................... 2-24
Right Front Passenger Position
.................... 1-21
RKE Personalization Features
..................... 2-92
Roadside Service
................................ 7-5
Rocking Your Vehicle
........................... 5-36
Rotation, Tires
................................. 6-43
Restraints
RKE .......................................... 2-1
Safety Belt Extender
............................ 1-53
Safety Belts
.................................... 1-6
Adults
...................................... 1-11
Center Passenger Position
...................... 1-29
Children
.................................... 1-34
How
to Wear Properly ......................... 1-11
Incorrect Usage
......................... 1-5 1, 1-52
Incorrect Usage
.............................. 1-16
Care ....................................... 6-51
DriverPosition ............................... 1-11
Extender
.................................... 1-53
LapBelt
.................................... 1-29
. 1~ . 8-9