display CADILLAC DTS 2008 1.G Owners Manual

Press a button to turn on the desired feature. A light on
that button will display to show which feature is on.
There are three temperature settings for each feature.
A column of three lights next to the buttons will
display which setting the feature is in: high, medium or
low. Three lights indicate the highest setting, two
lights for medium and one light for the lowest setting.
When you press a button, the feature will turn on at the
highest setting. Each time you press the button, the
feature will go down one temperature setting.
To turn the feature off, keep pressing the button until
the display lights turn off.
If your vehicle has remote vehicle start and is started
using the remote keyless entry transmitter, the front
heated seats will be turned on to the high setting if it is
cold outside. See “Remote Vehicle Start” under
Remote Keyless Entry (RKE) System Operation on
page 2-5. When the key is inserted into the ignition and
the ignition is turned on, this feature will turn off.
To turn it back on, press the desired button.Memory Seat, Mirrors and Steering
Wheel
Your vehicle may have the memory package.
The controls for this feature are located on the driver’s
door panel, and are used to program and recall
memory settings for the driver’s seat, outside mirror,
and the steering wheel position if the vehicle has
the power tilt wheel and telescopic steering feature.
To save your positions in memory, do the following:
1. Adjust the driver’s seat, including the seatback
recliner and lumbar, both outside mirrors, and
the steering wheel to a comfortable position.
2. Press and hold button 1 until two beeps sound
through the driver’s side front speaker to let you
know that the position has been stored.
1-4

Rear Seats
Heated Seats
Your vehicle may have heated rear seats.
To operate the rear heated seats, the ignition
must be on.
The buttons are located on
the rear doors.
I(Heated Seatback):Press to turn on the heated
seatback.
J(Heated Seat and Seatback):Press to turn on the
heated seat and seatback.
Press a button to turn on the desired feature. A light on
that button will display to show which feature is on.There are three temperature settings for each feature.
A column of three lights next to the buttons will
display which setting the feature is in: high, medium or
low. Three lights indicate the highest setting, two
lights for medium and one light for the lowest setting.
When you press a button, the feature will turn on at the
highest setting. Each time you press the button, the
feature will go down one temperature setting.
To turn the feature off, keep pressing the button until
the display lights turn off.
Rear Seat Pass-Through Door
Your vehicle has a pass-through door that provides
access to the trunk from the rear seats. See “Rear Seat
Pass-Through Door” underTrunk on page 2-12.
1-9

Q(Lock):Press to lock all the doors. If enabled
through the Driver Information Center (DIC), the parking
lamps may ash once to indicate locking has occurred,
or the horn may chirp when
Qis pressed again
within ve seconds from the previous press of the lock
button. SeeDIC Vehicle Customization on page 3-87
for additional information. If the vehicle has the content
theft-deterrent system, pressing
Qmay also arm it.
SeeContent Theft-Deterrent on page 2-19.
"(Unlock):Press to unlock the driver’s door. If"is
pressed again within ve seconds, all remaining doors
will unlock. The interior lamps will come on and stay
on for 20 seconds or until the ignition is turned on.
If enabled through the DIC, the parking lamps will ash
twice to indicate unlocking has occurred. SeeDIC Vehicle
Customization on page 3-87. Pressing
"on the RKE
transmitter may disarm the content theft-deterrent
system. SeeContent Theft-Deterrent on page 2-19.
V(Remote Trunk Release):Press and hold for
about one second to release the trunk lid. The
transmission must be in PARK (P) for this feature to
operate.
L(Vehicle Locator/Panic Alarm):Press and release
to locate your vehicle. The turn signal lamps will ash
and the horn will sound three times.
Press and hold
Lfor more than two seconds to
activate the panic alarm. The turn signal lamps will ash
and the horn will sound repeatedly for 30 seconds.
The alarm will turn off when the ignition is moved
to ON/RUN or
Lis pressed again. The ignition
must be in LOCK/OFF for the panic alarm to work.
Matching Transmitter(s) to Your
Vehicle
Each RKE transmitter is coded to prevent another
transmitter from unlocking your vehicle. If a transmitter
is lost or stolen, a replacement can be purchased
through your dealer/retailer. All transmitters need
to be re-coded to match the new transmitter.
The lost transmitter will no longer work after the new
transmitters are re-coded. The vehicle can have a
maximum of eight transmitters matched to it. See
RELEARN REMOTE KEY underDIC Operation and
Displays on page 3-70.
2-6

Battery Replacement
Replace the battery if the REPLACE BATTERY IN
REMOTE KEY message displays in the DIC. See
“REPLACE BATTERY IN REMOTE KEY” underDIC
Warnings and Messages on page 3-75for additional
information.
Notice:When replacing the battery, do not to touch
any of the circuitry on the transmitter. Static from
your body could damage the transmitter.
To replace the battery:
1. Separate the halves of the transmitter with a at,
thin object inserted into the notch, located above
the metal base.
2. Remove the old battery. Do not use a metal object.
3. Insert the new battery, positive side facing up.
Replace with a CR2032 or equivalent battery.
4. Put the transmitter back together tightly.
2-7

Programmable Automatic Door
Locks
Your vehicle is programmed so that, when the doors are
closed, the ignition is on, and the shift lever is moved
out of PARK (P), all the doors will lock. The doors
will unlock every time you stop the vehicle and move
the shift lever into PARK (P).
If someone needs to get out while your vehicle is not
in PARK (P), have the person use the manual lock knob
or power door lock switch. When the door is closed
again, it will not lock automatically. Use the manual lock
knob or power door lock switch to lock the door.
With the vehicle in PARK (P) and the ignition on, the
door locks can be programmed through prompts
displayed on the Driver Information Center (DIC). These
prompts allow the driver to choose various lock and
unlock settings. For programming information, seeDIC
Vehicle Customization on page 3-87.
Rear Door Security Locks
Your vehicle has security locks that prevent passengers
from opening the rear doors from the inside.
The rear door security locks are located on the inside
edge of each rear door. You must open the rear doors to
access them.
To assist you in nding the lock, your vehicle will have
one of the following:
To use these locks, do the following:
1. Turn the knob to the vertical position to engage
the lock.
2. Close the door.
3. Do the same for the other rear door.
2-11

Ignition Positions
With the ignition key in the ignition, the key can be
turned to four different positions:
In order to shift out of PARK (P), ignition must be in the
ON/RUN or ACC/ACCESSORY and the regular brake
pedal must be applied.
Notice:Using a tool to force the key from the
ignition switch could cause damage or break the
key. Use the correct key and turn the key only with
your hand. Make sure the key is in all the way. If
none of this works, then your vehicle needs service.A (LOCK/OFF):This is the only position in which the
ignition key can be inserted or removed. This position
locks the ignition and transmission and steering column.
It is a theft-deterrent feature.
If the steering wheel is locked, move it from right to left
and turn the key to ACC/ACCESSORY. If none of
this works, then your vehicle needs service.
B (ACC/ACCESSORY):This position lets the radio
and windshield wipers operate while the engine is off.
To use ACC/ACCESSORY, turn the key clockwise.
C (ON/RUN):This position is where the key returns to
after the vehicle is started. This position displays
some of the warning and indicator lights.
The battery could be drained if you leave the key in the
ACC/ACCESSORY or ON/RUN position with the engine
off. You may not be able to start your vehicle if the battery
is allowed to drain for an extended period of time.
D (START):This position starts the engine.
A warning chime will sound and the Driver Information
Center (DIC) will display DRIVER DOOR OPEN
when the driver’s door is opened if the ignition is in
LOCK/OFF, ACC/ACCESSORY and the key is in the
ignition. SeeDIC Warnings and Messages on page 3-75
for more information.
2-23

Mirrors
Automatic Dimming Rearview Mirror
The vehicle has an automatic dimming rearview
mirror with a compass display. The mirror may also
have OnStar
®controls and/or Intellibeam™. For more
information on OnStar, seeOnStar®System on
page 2-49. For more information on Intellibeam™ see
“Intellibeam Intelligent High-Beam Headlamp Control
System” underExterior Lamps on page 3-32.
O(On/Off):If the vehicle has this button, press to
turn the automatic dimming feature on or off.
Automatic Dimming Mirror Operation
Automatic dimming reduces the glare of lights from
behind the vehicle. The dimming feature comes on and
the indicator light illuminates each time the vehicle is
started.
Cleaning the Mirror
Do not spray glass cleaner directly on the mirror. Use a
soft towel dampened with glass.
Compass
Compass Operation
AUTO3/O(Auto Highbeam or On/Off):The
vehicle may have one of these buttons. Press and
hold AUTO
3for approximately three seconds or
press
Oto turn the compass on or off.
When the ignition is turned ON and this feature is on,
the compass displays in the mirror after a few seconds.
Compass Calibration
If the letter C should ever appear in the compass
display window, the compass may need to be calibrated.
If the correct compass direction does not show on the
display, there may be a strong magnetic eld interfering
with the compass, such as a magnetic antenna
mount, magnetic note pad holder or a similar magnetic
item. Remove the interference and calibrate the
compass, if calibrating is needed.
The compass can be placed in calibration mode
manually by pressing and holding AUTO
3orO
depending on the vehicle, until a C is shown in the
compass display.
To calibrate, drive the vehicle in a small circle slowly
until the display reads the correct direction.
2-36

Compass Variance
The mirror is set to zone eight. If you do not live in zone
eight or drive out of the area, the compass variance
needs to be changed to the appropriate zone.
To adjust for compass variance do the following:
1. Find the current location and variance zone number
on the following zone map.
2. Press and hold AUTO
3orOdepending on the
vehicle, until a zone number displays.
3. Once the zone number displays, press AUTO
3or
Omultiple times until the correct zone number
displays. Stop pressing the button and the mirror
returns to normal operation. If C appears in the
compass window, the compass may need
calibration. See Compass Calibration listed
previously.
2-37

The front display is located on top of the instrument panel
to the right of the driver. The front display will have either
three or six lights to provide distance and system
information. With Adaptive Cruise control (ACC), it will
have three lights along with the ACC lights. Without ACC,
it will have six lights. High-toned beeps from the front
speakers are for objects detected near the front bumper.
The rear display is located near the rear window and
can be seen by looking over your right shoulder.
The rear display uses three color-coded lights to provide
distance and system information. Low-toned beeps
from the rear speakers are for the rear bumper.
How the System Works
UFRPA comes on automatically when the shift
lever is moved out of PARK (P). The system does
not work at a forward or reverse speed greater than
5 mph (8 km/h).
To be detected, objects must be at least 10 inches
(25.4 cm) off the ground and below hood or trunk level.
Objects must also be within 4 feet (1.2 m) in front of
your vehicle and 8 feet (2.5 m) from your rear bumper.
This distance may be less during warmer or humid
weather.
When backing, if objects are detected at the same time
near both the front and rear bumpers, both color-coded
light displays will notify you of objects close to each
bumper. If there are objects detected near both bumpers,
the beeps will only be sounded to notify that objects are
close to the rear bumper. However, if while you are
backing and an object comes within 1 ft (0.3 m) of the
front bumper, and at the same time there is another
object further than 1 ft (0.3 m) from the rear bumper, then
the beeps will only be sounded to notify you of the closer
object that is near the front bumper.
The system can be disabled using the Driver Information
Center (DIC). See “Parking Assist” underDIC Operation
and Displays on page 3-70for more information. Front Parking Assist
Display
Rear Parking Assist
Display
2-41

Moving Forward
When the vehicle is started, the front display will briey
illuminate to let you know the system is working.
The following describes what will occur with the front
display as you get closer to a object detected in the front
of your vehicle:
Description English Metric
amber/amber lights
ACC — one amber light4 ft 1.2 m
four amber lights
ACC — two amber lights40 in 1.0 m
four amber/ two red lights
ACC — two amber
lights/one red light23 in 0.6 m
four amber/ two red lights
and beep for
three seconds
ACC — two amber
lights/one red light and
beep for three seconds1 ft 0.3 m
Backing
URPA comes on automatically when the shift lever is
moved into REVERSE (R). The rear display will then
briey illuminate to let you know the system is working.
The following describes what will occur with the rear
display as you get closer to an object detected in
the rear of your vehicle:
Description English Metric
amber light 8 ft 2.5 m
amber/amber lights 40 in 1.0 m
amber/amber/red lights 23 in 0.6 m
amber/amber/red lights
ashing and beep for
three seconds1 ft 0.3 m
The system can be disabled through the Driver
Information Center (DIC). See “Parking Assist” under
DIC Operation and Displays on page 3-70for more
information.
2-42