reset CADILLAC ELDORADO 2002 10.G User Guide

2-79

AVG MPH (Reset): Press the SKIP INFO button to
display the AVG MPH (Average Speed), then press
and hold the NO INFO RESET button until 0.0 AVG
MPH is displayed.

TIMER: This feature is like a stopwatch in that
you can clock the time it takes to get from one point
to another.
To operate, press the SKIP INFO button to display
TIMER. Each of the fields for the hours, minutes and
seconds are two numeric digits.
Once TIMER OFF 00:00:00 is displayed, press the
NO INFO RESET button to toggle between ON and
OFF. Once the TIMER is in OFF, press and hold
NO INFO RESET to reset the timer. If you will be
starting and stopping your vehicle
-- during a trip
for instance
-- the TIMER feature will automatically
start timing where it left off when you last stopped.
To reset it, press and hold the NO INFO RESET
button until the display reads TIMER 00:00:00.
Press the SKIP INFO button to exit from the
TIMER function.
ENGLISH/METRIC (Reset): Press the SKIP INFO
button to display ENGLISH/METRIC RESET,
then press the NO INFO RESET button to select.
The display will change from English (miles) to
metric (kilometers).

OIL LIFE LEFT (Reset): Press the SKIP INFO
button to display the OIL LIFE LEFT, then press and
hold the NO INFO RESET button until 100% OIL
LIFE LEFT is displayed. (This only needs to be reset
after you have had the oil changed.)
FUEL DOOR: Press this button to open the fuel
door. (This feature will work only when the shift lever is
in PARK (P) and the VALET lockout feature is turned
off, regardless of whether or not the vehicle is running.)
TRUNK: Press this button to open the trunk.
(This feature will work only when the shift lever is
in PARK (P) and the VALET lockout feature is
turned off, regardless of whether or not the vehicle
is running.)

2-80 DIC Messages
These messages will appear if there is a problem sensed
in one of your vehicle's systems. Vehicles that are first
sold in Canada will have a number after each message.
This number helps to identify the message which is
only displayed in English.
Pressing the INFO or NO INFO RESET button(s)
will remove most of the following messages from the
DIC display:
APPLY BRAKE TO SHIFT
- 46: This message
will appear if your vehicle is in PARK (P) for about
15 seconds and the brake is not pressed. On the climate
control panel, press the OFF button (next to the MODE
button) and the down arrow on the PASS TEMP button
for about five seconds. Hold the same two buttons to
display the message again.
BATTERY NOT CHARGING
- 7: This message will
appear if the battery is not being charged. Have the
electrical system checked by your dealership at your
earliest convenience.BATTERY VOLTAGE HIGH
- 8: This message
shows that the electrical charging system is
overcharging (more than 16 volts). To avoid being
stranded, have the electrical system checked by your
dealership. You can reduce the charging overload by
using the accessories. Turn on the lamps and radio, set
the climate control on AUTO and the fan speed on HI,
and turn the rear window defogger on. You can monitor
battery voltage on the DIC by pressing the SKIP INFO
button. The normal range is 11.5 to 15.5 volts when the
engine is running.
BATTERY VOLTAGE LOW
- 6: This message
will appear when the electrical system is charging
less than 10 volts or if the battery has been drained.
If this message appears immediately after starting,
it is possible that the generator can still recharge the
battery. The battery should recharge and may take a
few hours to do so. Consider using an auxiliary charger
to boost the battery after returning home or to a final
destination. (Be sure to follow the manufacturer's
instructions when using a battery charger.)

2-81
If this message appears and stays on while driving or
after starting your vehicle, have it checked immediately
to determine the cause of this problem. To help the
generator recharge the battery quickly, you can reduce
the load on the electrical system by turning off the
accessories. You can monitor battery voltage on the
DIC by pressing the SKIP INFO button. The normal
range is 11.5 to 15.5 volts.
CHANGE ENGINE OIL
- 82: This means that
the life of the engine oil has expired and it should be
changed within 200 miles (322 km). See ªEngine Oilº
in the Index. After an oil change, the Oil Life Indicator
must be reset. See ªOil Life Indicator, How to Resetº
in the Index.
CHANGE TRANS FLUID
- 47: This message will
appear when it is time to replace the transaxle fluid.
See ªMaintenance Scheduleº in the Index for the proper
fluid and change intervals.CHECK BRAKE FLUID LEVEL
- 37: This message
will display if the ignition is in RUN to inform the
driver that the brake fluid level is low. Have the brake
system serviced by a technician as soon as possible.
See ªBrake System Warning Lightº in the Index.
CHECK COOLANT LEVEL
- 2: This message
will appear when there is a low level of engine coolant.
Have the cooling system serviced by a technician as
soon as possible.
CHECK FUEL GAUGE
- 39: This message will
appear when the fuel supply is less than 3.5 gallons
(13.2 L) remaining. A single chime will also sound
when this message is displayed.
CHECK GAS CAP
- 61: This message will appear
if the gas cap has not been fully tightened. You should
recheck your gas cap to ensure that it's fully tightened.

2-83
ENGINE HOT - A/C OFF - 16: This message
displays when the engine coolant becomes hotter than
the normal operating temperature. To avoid added strain
on a hot engine, the air conditioning compressor is
automatically turned off so that air conditioned air is
not delivered. If the coolant temperature returns to
normal, you must select AC to return to a normal A/C
compressor operation. If this message continues to
appear, have the system repaired as soon as possible to
avoid compressor damage.
ENGINE MISFIRE
-- EASE OFF GAS
PEDAL
- 114: An engine misfire has occurred.
You'll need to ease off the gas pedal.
ENGINE OVERHEATED, STOP ENGINE
- 42:
This message will appear when the engine has overheated.
Stop and turn the engine off immediately to avoid severe
engine damage. See ªEngine Overheatingº in the Index.
A multiple chime will also sound when this message
is displayed.
ENGINE POWER REDUCED
- 41: This message
informs you that your vehicle is reducing engine power
because the transaxle is being placed in gear under
conditions that may cause damage to the vehicle
powertrain or vehicle acceleration.FUEL LEVEL LOW
- 11 : This message serves as
a warning that the fuel level in the tank is critically low.
Stop for fuel soon.
HEADLAMPS SUGGESTED
- 23: If it's dark enough
outside and Twilight Sentinel is off, a HEADLAMPS
SUGGESTED message will display on the DIC.
This message informs the driver that turning on the
exterior lamps is recommended even though the
Daytime Running Lamps (DRL) are still illuminated
(it's become dark enough outside to require the
headlamps and/or other exterior lamps).
ICE POSSIBLE
- 13: This message appears when
the outside air temperature is cold enough to create icy
road conditions.
LOW REFRIG A/C OFF
- 12: This message means
that the air conditioning system detects a refrigerant
level that is low enough to cause damage to the air
conditioning compressor. Have the air conditioning
system serviced if this message appears.
MONITORED SYSTEMS OK
- 1: This message only
appears in the ªrecallº mode by pressing the NO INFO
RESET button. It lets you know that no other messages
are stored or are currently active.

2-85
SERVICE CHARGING SYSTEM - 102: This
message will display when a problem with the charging
system has been detected. Have your vehicle serviced at
your dealership.
SERVICE ELECTRIC SYS
- 106: This message will
display if an electrical problem has occurred within the
Powertrain Control Module (PCM). Have your vehicle
serviced by your dealership.
SERVICE FUEL SYSTEM
- 101: The PCM has
detected a problem within the fuel system when this
message appears. See your dealership for service.
SERVICE IDLE CONTROL
- 107: A problem with
the idle control has occurred when this message displays.
Drive your vehicle to the dealership for service.
SERVICE RIDE SYS
- 84: This message is displayed
to indicate that the suspension system is not operating
properly. To correct this problem, have your vehicle
serviced at your dealership.SERVICE STEERING SYS
- 127: This message
is displayed when a problem has been detected in the
magnetic variable speed assist steering system.
Service is required. A single chime will also sound
when this message is displayed.
SERVICE TRANSMISSION
- 100: If a problem
is detected with the transaxle, this message will appear.
Have your vehicle checked by your dealership.
SERVICE VEHICLE SOON
- 3: If a problem is
detected with the transaxle, this message will appear.
Have your vehicle checked by your dealership.
SERV STABILITY SYS
- 54: If you ever see the
SERV STABILITY SYS message, it means there
may be a problem with your stability enhancement
system. If you see this message, try to reset the system
(stop, turn off the engine, then start the engine again).
If the SERV STABILITY SYS message still comes on,
it means there is a problem. You should see your dealer
for service. Reduce your speed and drive accordingly.
A single chime will also sound when this message
is displayed.

2-87
TOP SPEED FUEL OFF - 111 : This message will
appear when the PCM senses that the maximum speed
for your vehicle has been reached. The speed of your
vehicle will decrease several mph as the fuel supply is
cut off. This allows your vehicle to stay in a stable
operating range.
TRACTION ENGAGED
- 91: When your traction
control system is limiting wheel spin, the TRACTION
ENGAGED message will be displayed. Slippery road
conditions may exist if this message is displayed, so
adjust your driving accordingly. This message will stay
on for a few seconds after the traction control system
stops limiting wheel spin.
TRACTION OFF
- 89: This message will be displayed
after the traction control has been turned off.
TRACTION READY
- 90: This message informs
the driver that the traction control system is available.
This occurs when the traction on/off button in the glove
box has been returned to ON (pressing the button once
turns the traction control system off; pressing the button
again turns the system back on). This message also
self
-cancels after five seconds.TRACTION SUSPENDED
- 56: This message
displays when the traction control system has been
temporarily shut off because your vehicle's brakes
have overheated. This message does not indicate a
problem with your vehicle's traction control system.
After a few minutes, the traction control system will be
available again and the TRACTION READY message
will appear.
TRANS FLUID RESET
- 48: With the engine not
running and the ignition on, press and hold the OFF and
rear defog buttons located on the climate control panel
until the TRANS FLUID RESET message appears on
the DIC (between five and 20 seconds).
TRANS HOT IDLE ENG
- 112: This message
indicates that the transaxle fluid in your vehicle is too
hot. Stop and allow your vehicle to idle until it cools
down or until this message is removed.
TRUNK OPEN
- 24: This message indicates that the
trunk is open when your vehicle's ignition is in RUN.

2-88
TURN SIGNAL ON - 20: This message is a reminder,
after driving about 1 mile (1.6 km/h), that you have the
turn signal on. A multiple chime will also sound when
this message is displayed.
VEHICLE OVERSPEED
- 52: This message is
displayed when the vehicle speed exceeds a certain limit
as required by some export countries. A continuous
chime will also sound when this message is displayed.
VEHICLE SPEED LIMITED TO XXX MPH
(KM/H)
- 113: A failure in the suspension control
system has occurred when this message appears.
The Powertrain Control Module (PCM) determines
the speed your vehicle is limited to. Have your vehicle
serviced if this message appears. (The XXX indicates
the speed your vehicle is limited to.)
Memory and Personalization Features
(If Equipped)
Your vehicle may be equipped with the following
features that can be individually programmed, or
personalized, for up to two drivers. For a brief
description of the features, look up each feature in
the Index for a page reference.
Entering Feature Programming
To enter the feature programming mode,
do the following:
1. Turn the ignition to RUN.
2. Press and hold the SKIP INFO and NO INFO
RESET buttons at the same time until the first
programmable feature is displayed.

2-89
Programmable Automatic Door Locks
This feature allows you to program the way the vehicle's
doors lock and unlock.
Programmable Modes
Mode 1 (DOORS LOCK IN GEAR): All doors
automatically lock when shifted out of PARK (P).
No automatic door unlock.
Mode 2 (DRIVR UNLOCK IN PARK): All doors
automatically lock when shifted out of PARK (P).
Only the driver's door automatically unlocks when
shifted into PARK (P).
Mode 3 (DRIVR UNLOCK KEY OFF): All doors
automatically lock when shifted out of PARK (P).
Only the driver's door automatically unlocks when
the ignition key is turned to OFF.
Mode 4 (DOORS UNLOCK IN PARK): All doors
automatically lock when shifted out of PARK (P) and
unlock when shifting into PARK (P).
Mode 5 (DOORS UNLOCK KEY OFF): All doors
automatically lock when shifted out of PARK (P).
All doors automatically unlock when the ignition key
is turned to OFF.Before your vehicle was shipped from the factory, it was
programmed to enable Mode 1 and Mode 4. The modes
to which the vehicle was programmed may have been
changed since it left the factory. To determine the modes
to which the vehicle is programmed or to program the
vehicle to different modes, do the following:
1. Enter feature programming following the
instructions listed previously.
2. A yes or no response must be made after each mode
is displayed in order to continue to the next mode.
Press the YES TRIP RESET button to indicate yes,
or press the NO INFO RESET button to indicate no.
Once you have indicated the mode that you want
with a yes response, FEATURE ON will appear on
the display. FEATURE OFF appears when you
indicate a no response, and the display will advance
to the next mode.
LGHTS FLSH AT UNLOCK will appear once a
mode has been selected for the automatic door locks.
If you press the SKIP INFO button, the menu will
advance to the next feature available for programming.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-90
Lock/Unlock Confirmation
This personalization feature allows the driver to program
the parking lamps to flash when the buttons on the
remote keyless entry transmitter are pressed, to program
the horn to sound when the button with the lock symbol
is pressed and/or to program the exterior lamps to turn on
when the button with the unlock symbol is pressed on the
remote keyless entry transmitter.
Programmable Modes
Mode 1 (LGHTS FLSH AT UNLOCK): Parking
lamps flash twice when the button with the unlock
symbol on the remote keyless entry transmitter is pressed.
Mode 2 (LIGHTS FLASH AT LOCK): Parking lamps
flash once when the button with the lock symbol on the
remote keyless entry transmitter is pressed.
Mode 3 (HORN SOUNDS AT LOCK): Horn sounds
when the button with the lock symbol on the remote
keyless entry transmitter is pressed.Mode 4 (EXT LIGHTS AT UNLOCK): Exterior
lamps turn on when the button with the unlock symbol
on the remote keyless entry transmitter is pressed
and it is dark outside. These lamps stay on for about
20 seconds or until the key is turned to OFF.
Before your vehicle was shipped from the factory, it was
programmed to enable Mode 1 and Mode 2. The modes
to which the vehicle was programmed may have been
changed since it left the factory. To determine the modes
to which the vehicle is programmed or to program the
vehicle to different modes, do the following:
1. Enter feature programming following the
instructions listed previously.
2. Press the SKIP INFO button until LOCK/UNLOCK
appears on the display.
3. Press YES TRIP RESET to select this feature for
programming. Mode 1 described previously will
appear on the display once a yes response is made.

2-91
4. A yes or no response must be made after each mode
is displayed in order to continue to the next mode.
Press the YES TRIP RESET button to indicate yes,
or press the NO INFO RESET button to indicate no.
Once you have indicated the mode that you want
with a yes response, FEATURE ON will appear on
the display. FEATURE OFF appears when you
indicate a no response, and the display will advance
to the next mode.
REMOTE RECALL MEMORY will appear
once a mode has been selected for lock/unlock
confirmation feature.
If you press the SKIP INFO button, the menu will
advance to the next feature available for programming.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.Remote Recall Memory (If Equipped with
Memory Personalization)
Memory settings that have been previously programmed
(climate control settings, radio preset settings, exterior
lighting choices, remote confirmation choices and
programmable automatic door lock choices) can be
recalled by using the remote keyless entry transmitter
or by placing the key in your vehicle's ignition.
Programmable Modes
Mode 1 (REMOTE RECALL MEMORY):
The previously programmed driver's seat and mirror
positions are automatically recalled when the button
with the unlock symbol on the remote keyless entry
transmitter is used to unlock the vehicle.
Mode 2 (KEY IN RECALL MEMORY):
The previously programmed driver's seat and mirror
positions are automatically recalled when the ignition
is turned to RUN.