ignition CADILLAC ESCALADE 2021 Convenience & Personalization Guide

4
Lock
Press to lock all doors, fuel door and liftgate.
Unlock
Press to unlock the driver’s door and fuel door only or all doors and liftgate.
[ Remote Vehicle Start
Press twice to start the engine from outside the vehicle. After
entering the vehicle, press the ENGINE START/STOP button.
Rear Liftglass
Press twice to open the rear liftglass.
Power Liftgate
Press twice to open or close the power liftgate. Press once to stop power operation.
Vehicle Locator/Panic Alarm
Press and release to locate your vehicle. Press and hold for 3 seconds to activate the alarm. Press again to cancel the alarm.
Remote Power Windows
Press and hold the button to fully open the windows or the button to fully close the windows. To enable, go to Settings > Vehicle > Remote Lock, Unlock, and Start > Remote Window Operation.
Automatic Mirror Folding
To enable the automatic power folding mirrors, go to Settings > Vehicle > Comfort and Convenience > Remote Mirror Folding.
Note: To change or enable some settings, go to Settings > Vehicle > Remo\
te Lock, Unlock, and Start.
See Keys, Doors and Windows in your Owner's Manual.
REMOTE KEYLESS ENTRY
TRANSMITTER (KEY FOB)
KEYLESS ACCESS SYSTEM
The Keyless Access System enables operation of the doors and lift-gate without removing the Remote Keyless Entry transmitter (key fob) from your pocket or purse. The key fob must be within 3 feet of the liftgate or door being unlocked.
KEYLESS UNLOCKING
With the key fob within range:
Press the touchpad (A) on the back of the driver’s door handle to unlock the driver’s door or all doors and liftgate.
Press the touchpad on the back of a passenger door handle to unlock all doors and liftgate.
Press the Cadillac crest under the liftglass to open the liftgate.
KEYLESS LOCKING
With the key fob within range:
Press the Cadillac crest sensor (B) on the outside of a front door handle to lock all doors and liftgate immediately.
PASSIVE LOCKING
To have all doors lock automatically after the last door is closed, the ignition is off, and the key fob is removed from the vehicle, go to Settings > Vehicle > Remote Lock, Unlock, and Start > Passive Door Lock.
To have the driver's door or all doors unlock when using the touchpad on the driver's door handle, go to Settings > Vehicle > Remote Lock, Unlock, and Start > Passive Door Unlock.
See Keys, Doors and Windows in your Owner's Manual.
A
B

5
KEYLESS START
The Remote Keyless Entry trans-mitter (key fob) must be in the vehicle to turn on the ignition.
START
With the vehicle in Park or Neutral, press the brake pedal and then press and hold the ENGINE START/STOP
button to start the engine. The green indicator on the button will illuminate.
Note: If the key fob battery is weak, place the key fob in the front cupholder in the center console to enable the engine to start. Replace the key fob\
bat-tery as soon as possible.
STOP/OFF
Shift to Park and press the ENGINE START/STOP button to turn off the engine.
Retained Accessory Power will be available for 10 minutes to
operate the audio system until the driver’s door is opened and to operate the windows and sunroof♦ until any door is opened.
ACCESSORY MODE
With the engine off and the brake pedal NOT depressed, press the ENGINE START/STOP button to place the ignition system in the Accessory mode to operate the radio, windows and other accessories with the engine off. The amber indicator on the but-ton will illuminate.
See Driving and Operating in your Owner's Manual.
AUTO ENGINE STOP/START
Auto Stop is a fuel-saving feature that automatically turns off the engine when the brake pedal is pressed, the vehicle is at a complete stop, and operating conditions are met. In Auto Stop mode, an AUTO STOP message will display. When the brake pedal is released or the accelerator pedal is pressed, the engine will automatically restart.
The engine may remain running or restart when the vehicle is stopped if:
• A minimum vehicle speed was not reached prior to stopping.
• The engine or transmission is not at the required operating tem-perature.
• The outside temperature is not in the required operating range.
• The shift lever is in any gear other than Drive (D).
• The battery charge is low.
• The climate control system requires the engine to run based on the current settings.
• The Auto Stop has reached the maximum allowed time.
AUTO ENGINE STOP/START DISABLE
Press the $ Auto Stop button on the center console when the engine is running to turn off the stop/start system. The button indicator turns off when the system is disabled.
Auto Stop is turned on each time the vehicle is started.
Note: Disable Auto Engine Stop/Start when using the Rear Seat Media System for continuous play while driving.
See Driving and Operating in your Owner’s Manual.
♦ Optional equipment

RECALL FRONT SEAT MEMORY POSITIONS
Press and hold button 1, 2 or Exit until the set position is reached.
The memory/exit positions can be programmed to be recalled automatically when the ignition is turned on/off (for exit recall, the driver’s door must be opened).
To set the recall options, go to Settings > Vehicle > Seating Position > Seat Entry Memory and Seat Exit Memory.
2ND-ROW SEAT ADJUSTMENTS
To slide a 2nd-row seat, lift the front lever (E) on the side of the seat cushion.
To recline a 2nd-row seatback, lift the rear lever (F) on the side of the seat cushion and push on the seatback.
To fold a 2nd-row seat, lift the rear lever (F) on the side of the seat cushion or, from the 3rd-row seat, pull the strap on the
bottom of the seat-back. The seatback will fold forward. Lift the lever or pull the strap again to tumble the seat forward.
To return the seat to the upright position, pull down the seat and lift the seatback until it locks in place. Slide the seat rear-ward by using the lever (E) on the seat cushion.
Note: Do not slide the 2nd-row seat while folded.
See Seats and Restraints in your Owner’s Manual.
13
SEAT FEATURES
FRONT SEAT ADJUSTMENTS
A. Seat Adjustment
B. Seatback Recline
C. Lumbar Support
D. Seat Massage♦
SET FRONT SEAT MEMORY POSITIONS
With the ignition On or in Accessory mode:
1. Adjust the driver’s seat, power steering column and power outside mirrors to the desired positions.
2. Press and release the SET button on the driver’s door. A beep will sound.
3. Immediately press and hold button 1 or 2 until two beeps sound. Use the button that matches the Driver Information Center welcome message indicating driver 1 or 2.
To store seat and power steering column positions for exiting the vehicle, repeat the steps using the Exit button.
♦ Optional equipment
BC
D
E
A
F