check engine light CADILLAC ESCALADE ESV 2008 User Guide

Page 210 of 500

Oil Pressure Light
{ CAUTION: Do not keep driving if the oil pressure is low. If
you do, your engine can become so hot that it
catches re. You or others could be burned.
Check your oil as soon as possible and have
your vehicle serviced.
Notice: Lack of proper engine oil maintenance may
damage the engine. The repairs would not be covered
by your warranty. Always follow the maintenance
schedule in this manual for changing engine oil.
This light will come on
briey when you start your
engine. If it does not,
have your vehicle serviced. When the light comes on and stays on, it means that oil
is not owing through your engine properly. You
could be low on oil and you might have some other
system problem.
Security Light For information regarding
this light and the vehicle’s
security system, see
Content Theft-Deterrent on
page 2-21 .
Fog Lamp Light The fog lamp light will
come on when the fog
lamps are in use.
The light will go out when the fog lamps are turned off.
See Fog Lamps on page 3-21 for more information.
3-46

Page 218 of 500

CHECK TIRE PRESSURE This message displays when the pressure in one or
more of the vehicle’s tires needs to be checked.
This message also displays LEFT FRONT, RIGHT
FRONT, LEFT REAR, or RIGHT REAR to indicate which
tire needs to be checked. You can receive more than
one tire pressure message at a time. To read the other
messages that may have been sent at the same
time, press the set/reset button. If a tire pressure
message appears on the DIC, stop as soon as you can.
Have the tire pressures checked and set to those
shown on the Tire Loading Information label. See Tires
on page 5-56 , Loading Your Vehicle on page 4-35 ,
and Inflation - Tire Pressure on page 5-62 . The DIC also
shows the tire pressure values. See DIC Operation
and Displays on page 3-49 . If the tire pressure is low,
the low tire pressure warning light comes on. See
Tire Pressure Light on page 3-42 . DRIVER DOOR OPEN This message displays and a chime sounds if the driver
door is not fully closed and the vehicle is in a drive
gear. Stop and turn off the vehicle, check the door for
obstructions, and close the door again. Check to
see if the message still appears on the DIC.
ENGINE HOT A/C (Air Conditioning)
TURNED OFF This message displays when the engine coolant
becomes hotter than the normal operating temperature.
See Engine Coolant Temperature Gage on page 3-42 .
To avoid added strain on a hot engine, the air
conditioning compressor automatically turns off. When
the coolant temperature returns to normal, the air
conditioning compressor turns back on. You can
continue to drive your vehicle.
If this message continues to appear, have the system
repaired by your dealer/retailer as soon as possible
to avoid damage to the engine.
3-54

Page 222 of 500

SERVICE BRAKE SYSTEM This message displays along with the brake system
warning light if there is a problem with the brake system.
See Brake System Warning Light on page 3-40 . If this
message appears, stop as soon as possible and turn off
the vehicle. Restart the vehicle and check for the
message on the DIC display. If the message is still
displayed or appears again when you begin driving, the
brake system needs service as soon as possible.
See your dealer/retailer.
SERVICE BRAKES SOON This message displays if there is a problem with the
brake system. If this message appears, stop as soon as
possible and turn off the vehicle. Restart the vehicle
and check for the message on the DIC display. If
the message is still displayed or appears again when
you begin driving, the brake system needs service. See
your dealer/retailer.
SERVICE PARKING ASSIST This message displays if there is a problem with the
Ultrasonic Rear Parking Assist (URPA) system. Do not
use this system to help you park. See Ultrasonic
Rear Parking Assist (URPA) on page 2-48 for more
information. See your dealer/retailer for service. SERVICE STABILITRAK If your vehicle has StabiliTrak ®
and this message
displays, it means there may be a problem with the
StabiliTrak ®
system. If you see this message, try to reset
the system. Stop; turn off the engine for at least
15 seconds; then start the engine again. If this message
still comes on, it means there is a problem. You
should see your dealer/retailer for service. The vehicle
is safe to drive, however, you do not have the benet
of StabiliTrak ®
, so reduce your speed and drive
accordingly.
SERVICE SUSPENSION SYSTEM This message displays when the Road Sensing
Suspension (RSS) system is not operating properly.
Have your vehicle serviced by your dealer/retailer.
SERVICE THEFT DETERRENT SYSTEM This message displays when there is a problem with
the theft-deterrent system. The vehicle may or may not
restart so you may want to take the vehicle to your
dealer/retailer before turning off the engine. See
PASS-Key ®
III+ Operation on page 2-23 for more
information.
3-58

Page 223 of 500

SERVICE TIRE MONITOR SYSTEM This message displays if a part on the Tire Pressure
Monitor System (TPMS) is not working properly. The tire
pressure light also ashes and then remains on during
the same ignition cycle. See Tire Pressure Light on
page 3-42 . Several conditions may cause this message
to appear. See Tire Pressure Monitor Operation on
page 5-65 for more information. If the warning comes on
and stays on, there may be a problem with the TPMS.
See your dealer/retailer.
SERVICE TRACTION CONTROL If your vehicle has StabiliTrak ®
, this message displays
when there is a problem with the Traction Control
System (TCS). When this message displays, the system
will not limit wheel spin. Adjust your driving accordingly.
See your dealer/retailer for service. See StabiliTrak ®
System on page 4-6 for more information.
STABILITRAK OFF If your vehicle has StabiliTrak ®
, this message displays
when you turn off StabiliTrak ®
, or when the stability
control has been automatically disabled. To limit wheel
spin and realize the full benets of the stability
enhancement system, you should normally leave
StabiliTrak ®
on. However, you should turn StabiliTrak ®
off if your vehicle gets stuck in sand, mud, ice, or snow and you want to rock your vehicle to attempt to
free it, or if you are driving in extreme off-road conditions
and require more wheel spin. See If Your Vehicle is
Stuck in Sand, Mud, Ice, or Snow on page 4-33 . To turn
the StabiliTrak ®
system on or off, see StabiliTrak ®
System on page 4-6 .
There are several conditions that can cause this
message to appear.
One condition is overheating, which could occur if
StabiliTrak ®
activates continuously for an extended
period of time.
The message also displays if the brake system
warning light is on. See Brake System Warning
Light on page 3-40 .
The message could display if the stability system
takes longer than usual to complete its diagnostic
checks due to driving conditions.
The message displays if an engine or vehicle
related problem has been detected and the vehicle
needs service. See your dealer/retailer.
The message turns off as soon as the conditions that
caused the message to be displayed are no longer
present.
3-59

Page 224 of 500

TIGHTEN GAS CAP This message may display along with the check engine
light on the instrument panel cluster if the vehicle’s
fuel cap is not tightened properly. See Malfunction
Indicator Lamp on page 3-43 . Reinstall the fuel cap fully.
See Filling the Tank on page 5-7 . The diagnostic
system can determine if the fuel cap has been left off or
improperly installed. A loose or missing fuel cap
allows fuel to evaporate into the atmosphere. A few
driving trips with the cap properly installed should turn
this light and message off.
TIRE LEARNING ACTIVE This message displays when the Tire Pressure Monitor
System (TPMS) is re-learning the tire positions on
your vehicle. The tire positions must be re-learned after
rotating the tires or after replacing a tire or sensor.
See Tire Inspection and Rotation on page 5-69 ,
Tire Pressure Monitor System on page 5-64 , and
Inflation - Tire Pressure on page 5-62 for more
information.
TRACTION CONTROL OFF If your vehicle has StabiliTrak ®
, this message displays
when the Traction Control System (TCS) is turned
off. Adjust your driving accordingly. See StabiliTrak ®
System on page 4-6 for more information. TRANSMISSION HOT IDLE ENGINE Notice: If you drive your vehicle while the
transmission uid is overheating and the
transmission temperature warning is displayed on
the instrument panel cluster and/or DIC, you
can damage the transmission. This could lead to
costly repairs that would not be covered by
your warranty. Do not drive your vehicle with
overheated transmission uid or while the
transmission temperature warning is displayed.
This message displays along with a continuous chime if
the transmission uid in the vehicle gets hot. Driving
with the transmission uid temperature high can cause
damage to the vehicle. Stop the vehicle and let it
idle to allow the transmission to cool. This message
clears and the chime stops when the uid temperature
reaches a safe level.
TURN SIGNAL ON This message displays and a chime sounds if a turn
signal is left on for 3/4 of a mile (1.2 km). Move the turn
signal/multifunction lever to the off position.
3-60

Page 278 of 500

Avoid needless heavy braking. Some people drive
in spurts — heavy acceleration followed by heavy
braking — rather than keeping pace with traffic. This is
a mistake. The brakes might not have time to cool
between hard stops. The brakes will wear out much
faster if you do a lot of heavy braking. If you keep pace
with the traffic and allow realistic following distances,
you will eliminate a lot of unnecessary braking.
That means better braking and longer brake life.
If your vehicle’s engine ever stops while you are driving,
brake normally but do not pump the brakes. If you do,
the pedal could get harder to push down. If the
engine stops, you will still have some power brake
assist. But you will use it when you brake. Once the
power assist is used up, it can take longer to stop and
the brake pedal will be harder to push.
Adding non-dealer/non-retailer accessories can affect
your vehicle’s performance. See Accessories and
Modifications on page 5-3 . Antilock Brake System (ABS) Your vehicle has the Antilock Brake System (ABS), an
advanced electronic braking system that will help
prevent a braking skid.
When you start the engine and begin to drive away, ABS
will check itself. You might hear a momentary motor or
clicking noise while this test is going on. This is normal.
If there is a problem with
ABS, this warning light will
stay on. See Antilock
Brake System Warning
Light on page 3-41 .
Along with ABS, your vehicle has a Dynamic Rear
Proportioning (DRP) system. If there is a DRP problem,
both the brake and ABS warning lights come on
accompanied by a 10-second chime. The lights and
chime will come on each time the ignition is turned on
until the problem is repaired. See your dealer/retailer for
service.
4-4

Page 306 of 500

You can run the engine to keep warm, but be careful. { CAUTION: Snow can trap exhaust gases under your
vehicle. This can cause deadly CO (carbon
monoxide) gas to get inside. CO could
overcome you and kill you. You cannot see it
or smell it, so you might not know it is in your
vehicle. Clear away snow from around the
base of your vehicle, especially any that is
blocking the exhaust pipe. And check around
again from time to time to be sure snow does
not collect there.
Open a window just a little on the side of the
vehicle that is away from the wind. This will
help keep CO out.
Run your engine only as long as you must. This saves
fuel. When you run the engine, make it go a little
faster than just idle. That is, push the accelerator
slightly. This uses less fuel for the heat that you get and
it keeps the battery charged. You will need a
well-charged battery to restart the vehicle, and possibly
for signaling later on with the headlamps. Let the
heater run for a while.
4-32

Page 333 of 500

Service ........................................................... .5-3
Accessories and Modications ......................... .5-3
California Proposition 65 Warning .................... .5-3
California Perchlorate Materials Requirements .... .5-4
Doing Your Own Service Work ........................ .5-4
Adding Equipment to the Outside of Your
Vehicle ..................................................... .5-4
Fuel ............................................................... .5-5
Gasoline Octane ........................................... .5-5
Gasoline Specications ................................... .5-5
California Fuel .............................................. .5-5
Additives ...................................................... .5-6
Fuels in Foreign Countries .............................. .5-6
Filling the Tank ............................................. .5-7
Filling a Portable Fuel Container .................... .5-10
Checking Things Under the Hood ................... .5-10
Hood Release ............................................. .5-11
Engine Compartment Overview ...................... .5-12
Engine Oil .................................................. .5-14
Engine Oil Life System ................................. .5-16
Engine Air Cleaner/Filter ............................... .5-17
Automatic Transmission Fluid ........................ .5-20
Engine Coolant ............................................ .5-24
Coolant Surge Tank Pressure Cap ................. .5-26
Engine Overheating ...................................... .5-26 Overheated Engine Protection
Operating Mode ....................................... .5-28
Cooling System ........................................... .5-29
Engine Fan Noise ........................................ .5-33
Power Steering Fluid .................................... .5-34
Windshield Washer Fluid ............................... .5-35
Brakes ....................................................... .5-36
Battery ....................................................... .5-39
Jump Starting .............................................. .5-40
All-Wheel Drive ............................................. .5-45
Rear Axle ...................................................... .5-46
Front
Axle ..................................................... .5-47
Headlamp Aiming .......................................... .5-48
Bulb Replacement ......................................... .5-51
High Intensity Discharge (HID) Lighting ........... .5-51
Back-Up Lamps ........................................... .5-51
License Plate Lamp ..................................... .5-53
Replacement Bulbs ...................................... .5-53
Windshield Wiper Blade Replacement ............. .5-54
Tires ............................................................. .5-56
Tire Sidewall Labeling .................................. .5-57
Tire Terminology and Denitions .................... .5-59
Ination - Tire Pressure ................................ .5-62
High-Speed Operation .................................. .5-63
Tire Pressure Monitor System ........................ .5-64Section 5 Service and Appearance Care
5-1

Page 337 of 500

Fuel Use of the recommended fuel is an important part of the
proper maintenance of your vehicle. To help keep the
engine clean and maintain optimum vehicle
performance, we recommend the use of gasoline
advertised as TOP TIER Detergent Gasoline.
Gasoline Octane Use premium unleaded gasoline with a posted octane
rating of 91 or higher. You can also use regular
unleaded gasoline rated at 87 octane or higher, but
your vehicle’s acceleration could be slightly reduced,
and you might notice a slight audible knocking
noise, commonly referred to as spark knock. If the
octane is less than 87, you might notice a heavy
knocking noise when you drive. If this occurs, use a
gasoline rated at 87 octane or higher as soon as
possible. Otherwise, you could damage the engine.
If you are using gasoline rated at 87 octane or higher
and you hear heavy knocking, the engine needs service. Gasoline Specications At a minimum, gasoline should meet ASTM
specication D 4814 in the United States or
CAN/CGSB-3.5 or 3.511 in Canada. Some gasolines
contain an octane-enhancing additive called
methylcyclopentadienyl manganese tricarbonyl (MMT).
We recommend against the use of gasolines
containing MMT. See Additives on page 5-6 for
additional information.
California Fuel If your vehicle is certied to meet California Emissions
Standards, it is designed to operate on fuels that
meet California specications. See the underhood
emission control label. If this fuel is not available
in states adopting California emissions standards, your
vehicle will operate satisfactorily on fuels meeting
federal specications, but emission control system
performance might be affected. The malfunction
indicator lamp could turn on and your vehicle might fail
a smog-check test. See Malfunction Indicator Lamp
on page 3-43 . If this occurs, return to your authorized
dealer/retailer for diagnosis. If it is determined that
the condition is caused by the type of fuel used, repairs
might not be covered by your warranty.
5-5

Page 368 of 500

Brakes Brake Fluid The brake master cylinder
reservoir is lled with
DOT-3 brake uid. See
Engine Compartment
Overview on page 5-12
for the location of the
reservoir.
There are only two reasons why the brake uid level
in the reservoir might go down. The rst is that the brake
uid goes down to an acceptable level during normal
brake lining wear. When new linings are put in, the uid
level goes back up. The other reason is that uid is
leaking out of the brake hydraulic system. If it is, you
should have the brake hydraulic system xed, since
a leak means that sooner or later the brakes will
not work well. It is not a good idea to top off the brake uid. Adding
brake uid will not correct a leak. If uid is added when
the linings are worn, there will be too much uid
when new brake linings are installed. Add or remove
brake uid, as necessary, only when work is done on the
brake hydraulic system.
{ CAUTION: If you have too much brake uid, it can spill on
the engine. The uid will burn if the engine is
hot enough. You or others could be burned,
and your vehicle could be damaged. Add brake
uid only when work is done on the brake
hydraulic system. See “Checking Brake Fluid”
in this section.
When the brake uid falls to a low level, the brake
warning light will come on. See Brake System Warning
Light on page 3-40 .
Refer to the Maintenance Schedule to determine when
to check the brake uid. See Scheduled Maintenance
on page 6-4 .
5-36

Page:   < prev 1-10 11-20 21-30 next >