horn CADILLAC ESCALADE ESV 2009 Owners Manual

Remote Keyless Entry (RKE)
System Operation The Remote Keyless Entry (RKE) transmitter functions
work up to 195 feet (60 m) away from the vehicle.
There are other conditions which can affect the
performance of the transmitter. See Remote Keyless
Entry (RKE) System on page 2-4 . The following functions may be available if this vehicle
has the RKE system:
Q (Lock): Press to lock all the doors.
If enabled through the Driver Information Center (DIC),
the turn signal lamps ash once to indicate locking
has occurred. If enabled through the DIC, the horn
chirps when
Q is pressed again within three seconds.
See DIC Vehicle Customization on page 3-65 for
additional information.
Pressing
Q arms the content theft-deterrent system.
See Content Theft-Deterrent on page 2-21 .
K (Unlock): Press once to unlock only the driver door.
If
K is pressed again within three seconds, all
remaining doors unlock. The interior lamps may come
on and stay on for 20 seconds or until the ignition
is turned on.
If enabled through the DIC, the turn signal lamps ash
twice to indicate unlocking has occurred. See DIC
Vehicle Customization on page 3-65 . If enabled through
the DIC, the exterior lights turn on briey if it is dark
enough outside. See “APPROACH LIGHTING” under
DIC Vehicle Customization on page 3-65 .With Remote Start and
Power Liftgate and
Liftglass (Without
Remote Start Similar)
2-5

Pressing
K on the RKE transmitter disarms the content
theft-deterrent system. See Content Theft-Deterrent on
page 2-21 .
/ (Remote Vehicle Start): For vehicles with this
feature, press
/ to start the engine from outside the
vehicle using the RKE transmitter. See Remote Vehicle
Start on page 2-8 for additional information.
& (Power Liftgate): Press and hold to open and
close the liftgate. The taillamps ash and a chime
sounds to indicate when the liftgate is opening and
closing.
m (Liftglass): Press and hold to open the liftglass.
L (Vehicle Locator/Panic Alarm): Press and release
to locate the vehicle. The turn signal lamps ash and
the horn sounds three times.
Press and hold
L for more than two seconds to activate
the panic alarm. The turn signal lamps ash and the horn
sounds repeatedly for 30 seconds. The alarm turns off
when the ignition is moved to ON/RUN or
L is pressed
again. The ignition must be in LOCK/OFF for the panic
alarm to work. The vehicle comes with two transmitters. Each
transmitter will have a number on top of it, “1” or “2”.
These numbers correspond to the driver of the vehicle.
For example, the memory seat position for driver 1
will be recalled when using the transmitter labeled “1”, if
enabled through the DIC. See Memory Features on
page 1-7 and DIC Vehicle Customization on page 3-65
for more information.
Programming Transmitters to the
Vehicle Only RKE transmitters programmed to this vehicle
will work. If a transmitter is lost or stolen, a replacement
can be purchased and programmed through your
dealer/retailer. When the replacement transmitter is
programmed to this vehicle, all remaining transmitters
must also be reprogrammed. Any lost or stolen
transmitters will no longer work once the new transmitter
is programmed. Each vehicle can have up to eight
transmitters programmed to it. See “Relearn Remote
Key” under DIC Operation and Displays on page 3-48 for
instructions on how to match RKE transmitters to the
vehicle.
2-6

Theft-Deterrent Systems Vehicle theft is big business, especially in some cities.
This vehicle has theft-deterrent features, however,
they do not make it impossible to steal.
Content Theft-Deterrent Your vehicle has a content theft-deterrent alarm system.
This is the security light.
To arm the theft-deterrent system:
1. Open the door.
2. Lock the door with the Remote Keyless Entry (RKE)
transmitter or the power door lock switch. The
security light will come on to inform the driver the
system is arming. If a door is open when the doors
are locked, the security light will ash.
If the delayed locking feature is turned on, the
theft-deterrent system will not start the arming
process until the last door is closed and the delay
timer has expired. See Delayed Locking on
page 2-10 . 3. Close all doors. The security light should go off
after about 30 seconds. The alarm is not armed
until the security light goes off.
If a locked door is opened without using the RKE
transmitter, a ten second pre-alarm will occur. The
horn will chirp and the lights will ash. If the key is not
placed in the ignition and turned to START or the door is
not unlocked by pressing the unlock button on the RKE
transmitter during the ten second pre-alarm, the alarm will
go off. Your vehicle’s headlamps will ash and the horn
will sound for about 30 seconds, then will turn off to save
the battery power.
The theft-deterrent system will not activate if the doors
are locked with the vehicle’s key or the manual door lock.
It activates only if you use the power door lock switch with
the door open or the RKE transmitter. You should also
remember that you can start your vehicle with the correct
ignition key if the alarm has been set off.
To avoid setting off the alarm by accident:
If you do not want to activate the theft-deterrent
system, the vehicle should be locked with the
door key after the doors are closed.
Always unlock the doors with the RKE transmitter.
Unlocking a door any other way will set off the
alarm if it is armed.
If you set off the alarm by accident, press unlock on the
RKE transmitter or place the key in the ignition and turn it
to START to turn off the alarm. The alarm will not stop if
you try to unlock a door any other way.
2-21

Testing the Alarm To test the alarm:
1. From inside the vehicle, lower the driver’s window
and open the driver’s door.
2. Activate the system by locking the doors with the
power door lock switch while the door is open, or
with the RKE transmitter.
3. Get out of the vehicle, close the door and wait for
the security light to go out.
4. Then reach in through the window, unlock the door
with the manual door lock and open the door.
This should set off the alarm.
While the alarm is set, the power door unlock switch will
not work.
If the alarm does not sound when it should but the
headlamps ash, check to see if the horn works.
The horn fuse may be blown. To replace the fuse,
see Fuses and Circuit Breakers on page 6-106 .
If the alarm does not sound or the headlamps do
not ash, the vehicle should be serviced by your
dealer/retailer. PASS-Key ®
III+ Electronic
Immobilizer The PASS-Key III+ system operates on a radio
frequency subject to Federal Communications
Commission (FCC) Rules and with Industry Canada.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation of the device.
Changes or modications to this system by other than
an authorized service facility could void authorization to
use this equipment.
PASS-Key III+ uses a radio frequency transponder in
the key that matches a decoder in the vehicle.
2-22

Instrument Panel Overview .............................. .3-4
Hazard Warning Flashers ............................... .3-6
Horn ............................................................ .3-6
Tilt Wheel .................................................... .3-6
Heated Steering Wheel .................................. .3-6
Turn Signal/Multifunction Lever ........................ .3-7
Turn and Lane-Change Signals ....................... .3-8
Headlamp High/Low-Beam Changer ................. .3-8
Flash-to-Pass ................................................ .3-9
Windshield Wipers ......................................... .3-9
Rainsense™ II Wipers .................................. .3-10
Windshield Washer ...................................... .3-11
Rear Window Wiper/Washer .......................... .3-12
Cruise Control ............................................. .3-13
Exterior Lamps ............................................ .3-16
Headlamps on Reminder ............................... .3-21
Daytime Running Lamps (DRL) ...................... .3-21
Automatic Headlamp System ......................... .3-21
Fog Lamps ................................................. .3-22
Instrument Panel Brightness .......................... .3-23
Dome Lamps .............................................. .3-23
Dome Lamp Override ................................... .3-23
Entry Lighting .............................................. .3-23
Exit Lighting ................................................ .3-23
Reading Lamps ........................................... .3-24
Electric Power Management .......................... .3-24 Battery Run-Down Protection ......................... .3-25
Accessory Power Outlet(s) ............................ .3-25
Ashtray(s) and Cigarette Lighter ..................... .3-26
Analog Clock .............................................. .3-26
Climate Controls ........................................... .3-27
Dual Automatic Climate Control System .......... .3-27
Outlet Adjustment ........................................ .3-31
Rear Air Conditioning and Heating System
and Electronic Climate Controls .................. .3-32
Warning Lights, Gages, and Indicators ........... .3-33
Instrument
Panel Cluster ............................... .3-34
Speedometer and Odometer .......................... .3-35
Trip Odometer ............................................. .3-35
Tachometer ................................................ .3-35
Safety Belt Reminders .................................. .3-35
Airbag Readiness Light ................................. .3-36
Passenger Airbag Status Indicator .................. .3-37
Charging System Light ................................. .3-38
Brake System Warning Light ......................... .3-39
Antilock Brake System (ABS) Warning Light .... .3-40
StabiliTrak ®
Indicator Light ............................ .3-40
Engine Coolant Temperature Gage ................. .3-41
Tire Pressure Light ...................................... .3-41
Malfunction Indicator Lamp ............................ .3-42
Oil Pressure Light ........................................ .3-44Section 3 Instrument Panel
3-1

The main components of the instrument panel are the following:
A. Outlet Adjustment on page 3-31 .
B. Turn Signal/Multifunction Lever on page 3-7 .
C. Instrument Panel Cluster on page 3-34 .
D. Hazard Warning Flashers on page 3-6 .
E. Shift Lever and Range Selection Mode.
See Automatic Transmission Operation
on page 2-29 .
F. Tow/Haul Mode on page 2-33 .
G. Driver Information Center (DIC) on page 3-47 .
H. Analog Clock on page 3-26 .
I. Audio System(s) on page 3-75 .
J. StabiliTrak ®
System on page 5-6 . Rear Park Aid
Disable Button. See Ultrasonic Rear Parking
Assist (URPA) on page 2-42 .
K. Tilt Wheel on page 3-6 .
L. Exterior Lamps on page 3-16 . M. Dome Lamp Override on page 3-23 . Instrument
Panel Brightness on page 3-23 . Fog Lamps
on page 3-22 .
N. Automatic Transfer Case Control. See Escalade
Two-Mode Hybrid Supplement for more information.
O. Cruise Control on page 3-13 . Heated Steering
Wheel on page 3-6 (If Equipped).
P. Horn on page 3-6 .
Q. Audio Steering Wheel Controls on page 3-115 .
R. Dual Automatic Climate Control System on
page 3-27 .
S. Pedal Adjust Button. See Adjustable Throttle and
Brake Pedal on page 2-27 . Heated Windshield
Washer Fluid Button. See Windshield Washer
on page 3-11 . Power Assist Steps on page 2-16
(If Equipped).
T. Glove Box on page 2-62 .
3-5

Hazard Warning Flashers | (Hazard Warning Flasher): Press this button
located on top of the steering column, to make the front
and rear turn signal lamps ash on and off. This warns
others that you are having trouble. Press again to turn
the ashers off.
When the hazard warning ashers are on, the vehicle’s
turn signals will not work.
Horn To sound the horn, press the center pad on the steering
wheel.
Tilt Wheel The power tilt wheel
control is located on the
left side of the steering
column. Push the control up or down to tilt the steering wheel up
or down.
To set the memory position, see Memory Features on
page 1-7 .
Heated Steering Wheel For vehicles with a heated steering wheel, the button for
this feature is located on the steering wheel.
( : Press to turn the heated steering wheel on or off.
A light on the button displays when the feature is
turned on.
The steering wheel takes about three minutes to start
heating.
3-6

AUTO DOOR UNLOCK This feature allows you to select whether or not to
turn off the automatic door unlocking feature. It also
allows you to select which doors and when the doors
will automatically unlock. See Programmable Automatic
Door Locks on page 2-11 for more information.
Press the customization button until AUTO DOOR
UNLOCK appears on the DIC display. Press the
set/reset button once to access the settings for this
feature. Then press the customization button to scroll
through the following settings:
OFF: None of the doors will automatically unlock.
DRIVER AT KEY OUT: Only the driver’s door will
unlock when the key is taken out of the ignition.
DRIVER IN PARK: Only the driver’s door will unlock
when the vehicle is shifted into P (Park).
ALL AT KEY OUT: All of the doors will unlock when
the key is taken out of the ignition.
ALL IN PARK (default): All of the doors will unlock
when the vehicle is shifted into P (Park).
NO CHANGE: No change will be made to this feature.
The current setting will remain.
To select a setting, press the set/reset button while the
desired setting is displayed on the DIC. REMOTE DOOR LOCK This feature allows you to select the type of feedback
you will receive when locking the vehicle with the
Remote Keyless Entry (RKE) transmitter. You will not
receive feedback when locking the vehicle with the RKE
transmitter if the doors are open. See Remote Keyless
Entry (RKE) System Operation on page 2-5 for more
information.
Press the customization button until REMOTE DOOR
LOCK appears on the DIC display. Press the set/reset
button once to access the settings for this feature.
Then press the customization button to scroll through
the following settings:
OFF: There will be no feedback when you press the
lock button on the RKE transmitter.
LIGHTS ONLY: The exterior lamps will ash when you
press the lock button on the RKE transmitter.
HORN ONLY: The horn will sound on the second press
of the lock button on the RKE transmitter.
HORN & LIGHTS (default): The exterior lamps
will ash when you press the lock button on the RKE
transmitter, and the horn will sound when the lock button
is pressed again within ve seconds of the previous
command.
NO CHANGE: No change will be made to this feature.
The current setting will remain.
3-67

Sound the horn as you approach the top of the hill
to let opposing traffic know you are there.
Use headlamps even during the day to make the
vehicle more visible to oncoming traffic.
{ CAUTION: Driving to the top (crest) of a hill at full speed can
cause an accident. There could be a drop-off,
embankment, cliff, or even another vehicle. You
could be seriously injured or killed. As you near
the top of a hill, slow down and stay alert.
If the vehicle stalls, or is about to stall, and you cannot
make it up the hill:
Push the brake pedal to stop the vehicle and keep
it from rolling backwards and apply the parking
brake.
If the engine is still running, shift the transmission to
R (Reverse), release the parking brake, and slowly
back down the hill in R (Reverse).
If the engine has stopped running, you need to
restart it. With the brake pedal pressed and the
parking brake still applied, shift the transmission to P (Park) and restart the engine. Then, shift to
R (Reverse), release the parking brake, and slowly
back down the hill as straight as possible in
R (Reverse).
While backing down the hill, put your left hand on the
steering wheel at the 12 o’clock position so you can
tell if the wheels are straight and can maneuver as
you back down. It is best to back down the hill with
the wheels straight rather than in the left or right
direction. Turning the wheel too far to the left or right
will increase the possibility of a rollover.
Things not to do if the vehicle stalls, or is about to stall,
when going up a hill:
Never attempt to prevent a stall by shifting into
N (Neutral) to rev-up the engine and regain forward
momentum. This will not work. The vehicle can roll
backward very quickly and could go out of control.
Never try to turn around if about to stall when going
up a hill. If the hill is steep enough to stall the vehicle,
it is steep enough to cause it to roll over. If you
cannot make it up the hill, back straight down the hill.
If, after stalling, you try to back down the hill and decide
you just cannot do it, set the parking brake, put your
transmission in P (Park), and turn off the engine. Leave
the vehicle and go get some help. Exit on the uphill side
and stay clear of the path the vehicle would take if it rolled
downhill.
5-20

You have two minutes to match the rst tire/wheel
position, and ve minutes overall to match all four
tire/wheel positions. If it takes longer than two minutes, to
match the rst tire and wheel, or more than ve minutes
to match all four tire and wheel positions the matching
process stops and you need to start over.
The TPMS sensor matching process is outlined below:
1. Set the parking brake.
2. Turn the ignition switch to ON/RUN with the
engine off.
3. Press the Remote Keyless Entry (RKE) transmitter’s
LOCK and UNLOCK buttons at the same time for
approximately ve seconds. The horn sounds
twice to signal the receiver is in relearn mode
and TIRE LEARNING ACTIVE message displays
on the DIC screen.
4. Start with the driver side front tire. 5. Remove the valve cap from the valve cap stem.
Activate the TPMS sensor by increasing or
decreasing the tire’s air pressure for ve seconds,
or until a horn chirp sounds. The horn chirp,
which may take up to 30 seconds to sound,
conrms that the sensor identication code has
been matched to this tire and wheel position.
6. Proceed to the passenger side front tire, and repeat
the procedure in Step 5.
7. Proceed to the passenger side rear tire, and repeat
the procedure in Step 5.
8. Proceed to the driver side rear tire, and repeat the
procedure in Step 5. The horn sounds two times to
indicate the sensor identication code has been
matched to the driver side rear tire, and the TPMS
sensor matching process is no longer active. The
TIRE LEARNING ACTIVE message on the DIC
display screen goes off.
9. Turn the ignition switch to LOCK/OFF.
10. Set all four tires to the recommended air pressure
level as indicated on the Tire and Loading
Information label.
11. Put the valve caps back on the valve stems.
6-68