ignition CADILLAC SRX 2008 1.G Owners Manual

Stowable Seat
If your vehicle has a third row seat, it is a power
folding seat.
The head rests must be removed before folding the
third row seat, seeHead Restraints on page 1-9.
The buttons to operate the power folding third row seat
are inside the liftgate and behind the second row seat on
the passenger’s side of the vehicle.
e:Press to tilt the seatback forward or rearward.
f:Press to fold the seat.
Notice:Folding a rear seat with the safety belts
still fastened may cause damage to the seat or
the safety belts. Always unbuckle the safety belts
and return them to their normal stowed position
before folding a rear seat.Before folding or unfolding the third row seat, all of the
following conditions must be met:
The liftgate or passenger’s side rear door must
be open.
The unlock button on either the remote keyless entry
transmitter or the door must be pressed three times
to enable the rear seat for two minutes, or the ignition
must be in ON/RUN or ACC/ACCESSORY.
The vehicle must be in PARK (P).
The vehicle cannot have a low battery.
After the seat is folded, fold the panel on the seat
forward at on the oor.
If the seat’s path is blocked it will stop and back away.
Press the button again to return the seat to its previous
position.
Before returning the third row seat to the passenger
seating position, the panel must be folded back upon
itself. Press and hold one of the power folding seat
buttons and the seat will unfold into the seating position.
If the seat is not unfolded fully into the seating position,
a chime will sound when the vehicle is shifted out of
PARK (P). This indicates that the seat is not ready
for a passenger.
Replace the head rests.
1-12

Servicing Your Airbag-Equipped
Vehicle
Airbags affect how your vehicle should be serviced.
There are parts of the airbag system in several places
around your vehicle. Your dealer/retailer and the service
manual have information about servicing your vehicle
and the airbag system. To purchase a service manual,
seeService Publications Ordering Information on
page 7-17.
{CAUTION:
For up to 10 seconds after the ignition is turned
off and the battery is disconnected, an airbag
can still inate during improper service. You
can be injured if you are close to an airbag when
it inates. Avoid yellow connectors. They are
probably part of the airbag system. Be sure to
follow proper service procedures, and make
sure the person performing work for you is
qualied to do so.
Adding Equipment to Your
Airbag-Equipped Vehicle
Q:Is there anything I might add to or change
about the vehicle that could keep the airbags
from working properly?
A:Yes. If you add things that change your vehicle’s
frame, bumper system, height, front end or side
sheet metal, they may keep the airbag system from
working properly. Changing or moving any parts
of the front seats, safety belts, the airbag sensing
and diagnostic module, steering wheel, instrument
panel, roof-rail airbag modules, ceiling headliner
or pillar garnish trim, front sensors, side impact
sensors, rollover sensor module, or airbag wiring
can affect the operation of the airbag system.
1-70

Keys...............................................................2-3
Remote Keyless Entry (RKE) System................2-4
Remote Keyless Entry (RKE) System
Operation...................................................2-5
Remote Vehicle Start......................................2-7
Doors and Locks............................................2-10
Door Locks..................................................2-10
Central Door Unlocking System......................2-10
Power Door Locks........................................2-10
Delayed Locking...........................................2-11
Programmable Automatic
Door Locks...............................................2-11
Rear Door Security Locks..............................2-12
Lockout Protection........................................2-12
Power Liftgate..............................................2-13
Windows........................................................2-16
Power Windows............................................2-17
Sun Visors...................................................2-20
Theft-Deterrent Systems..................................2-20
Theft-Deterrent System..................................2-20
PASS-Key
®III+............................................2-22
PASS-Key®III+ Operation..............................2-22Starting and Operating Your Vehicle................2-24
New Vehicle Break-In....................................2-24
Ignition Positions..........................................2-25
Retained Accessory Power (RAP)...................2-26
Starting the Engine.......................................2-26
Adjustable Throttle and Brake Pedal................2-28
Engine Coolant Heater..................................2-28
Automatic Transmission Operation...................2-30
Tow/Haul Mode............................................2-33
Parking Brake..............................................2-34
Shifting Into PARK (P)...................................2-36
Shifting Out of PARK (P)...............................2-38
Parking Over Things That Burn.......................2-38
Engine Exhaust............................................2-39
Running the Engine While Parked...................2-40
Mirrors...........................................................2-41
Automatic Dimming Rearview
Mirror with OnStar
®...................................2-41
Automatic Dimming Rearview Mirror with
OnStar
®and Compass...............................2-41
Outside Power Heated Mirrors........................2-43
Outside Automatic Dimming Mirror..................2-44
Park Tilt Mirrors............................................2-44
Outside Convex Mirror...................................2-44
Section 2 Features and Controls
2-1

Keys
{CAUTION:
Leaving children in a vehicle with the ignition
key is dangerous for many reasons, children
or others could be badly injured or even killed.
They could operate the power windows or
other controls or even make the vehicle move.
The windows will function with the keys in the
ignition and they could be seriously injured
or killed if caught in the path of a closing
window. Do not leave the keys in a vehicle
with children.
The key can be used for the ignition and door locks.
If you ever lose your keys, your dealer/retailer will
be able to assist you with obtaining replacements.
Notice:If you ever lock your keys in your vehicle,
you may have to damage the vehicle to get in.
Be sure you have spare keys.
If you are locked out of your vehicle, contact Roadside
Service. SeeRoadside Service on page 7-8for more
information.
2-3

You can program your vehicle so that the exterior lamps
will ash when you unlock the doors with the RKE
transmitter. SeeDIC Vehicle Customization on page 3-62
for more information on programming this feature.
If your vehicle is programmed for remote conrmation,
the doors must be closed for this feature to work.
If a door is open, remote conrmation will be canceled.
/(Remote Vehicle Start):Your vehicle may be
started from outside the vehicle using the RKE
transmitter. SeeRemote Vehicle Start on page 2-7.
L(Panic Alarm):Press and release this button to
locate your vehicle. The turn signal lamps will ash and
the horn will sound three times. Press and hold this
button for more than two seconds to activate the panic
alarm. The turn signal lamps will ash and the horn
will sound repeatedly for 30 seconds. The alarm will
turn off when the ignition is turned to ON/RUN or
the alarm button is pressed again. The ignition must
be in LOCK/OFF for the panic alarm to work.
&(Power Liftgate):Press and hold this button
on the RKE transmitter to open and close the liftgate.
The taillamps will ash and a chime will sound to
indicate when the liftgate is opening and closing.
Matching Transmitter(s) to
Your Vehicle
Each RKE transmitter is coded to prevent another
transmitter from unlocking your vehicle. If a transmitter
is lost or stolen, a replacement can be purchased
through your dealer/retailer. Remember to bring any
additional transmitters with you so that all of them
can be re-coded to match the new transmitter. Once your
dealer/retailer has coded the new transmitter, the lost
transmitter will not unlock your vehicle. Each vehicle can
have a maximum of eight transmitters matched to it.
See RELEARN REMOTE KEY underDIC Operation and
Displays on page 3-48
Battery Replacement
Under normal use, the battery in your RKE transmitter
should last about four years.
The battery is weak if the transmitter will not work at the
normal range in any location. If you have to get close to
your vehicle before the transmitter works, it is probably
time to change the battery.
The REPLACE BATTERY IN REMOTE KEY message in
the vehicle’s DIC will display if the RKE transmitter
battery is low. See “REPLACE BATTERY IN REMOTE
KEY” underDIC Warnings and Messages on page 3-53.
2-6

To manually shut off a remote start:
Aim the RKE transmitter at the vehicle and
press the remote start button until the
parking lamps turn off.
Turn on the hazard warning ashers.
Turn the ignition switch on and then off.
The remote vehicle start feature provides two separate
starts, each with 10 minutes of engine running, or it
provides one start with 10 minutes of engine running
that may be extended 10 more minutes. If you press
and release the transmitter lock button and then
press and hold the remote start button on the RKE
transmitter again before the rst 10 minutes of engine
running time has expired, 10 minutes are added to
the remaining minutes. For example, if the lock button
and then the remote start buttons are pressed again
after ve minutes of the engine run time, 10 minutes
are added and you now have 15 minutes of engine
running. The added ten minutes are considered
a second remote vehicle start.Once two remote starts or a single start with a time
extension have been used, the vehicle must be started
with the ignition key before you can use the remote
start feature again.
The remote vehicle start feature will not operate if the
key is in the ignition, the hood is not closed, or if there
is an emission control system malfunction.
The engine will turn off during a remote vehicle start
if the coolant temperature gets too high, or the oil
pressure is too low.
Your vehicle was shipped from the factory with the
remote vehicle start system enabled. The system may
be disabled through the Driver Information Center (DIC).
See “REMOTE START” underDIC Vehicle
Customization on page 3-62for additional information.
SeeEngine Exhaust on page 2-39for important
safety information when using remote start in a
closed garage.
2-9

Delayed Locking
With this feature, you can delay the actual locking
of the doors.
When the power door lock switch or the lock button on
the remote keyless entry transmitter is pressed when
the key is not in the ignition and the driver’s door
is opened, a chime will sound three times indicating
that delayed locking is active.
When all the doors are closed, the doors will lock
automatically after ve seconds. If a door is reopened
before ve seconds have elapsed, the ve second timer
will reset itself once all the doors are closed again.
You can press the door lock switch or the lock button
on the remote keyless entry transmitter again to override
this feature and lock the doors immediately.
You can turn this feature off using the Driver Information
Center (DIC). When delayed locking is off, the doors
will lock immediately when you press the power
door lock switch or the lock button on the remote keyless
entry transmitter. SeeDIC Vehicle Customization
on page 3-62for more information.
Programmable Automatic
Door Locks
Your vehicle is programmed so that when the doors
are closed, the ignition is on and the shift lever is
moved out of PARK (P), all the doors will lock. The front
doors will remain unlocked from inside the vehicle.
The doors will unlock every time you stop the vehicle
and move the shift lever back into PARK (P).
If someone needs to exit the vehicle once the doors
are locked, have that person use the manual lever
or power door lock switch for the rear doors. When
the door is closed again, it will not lock automatically.
Use the manual lever or the power door lock switch
to lock the door.
The power door locks can be programmed through
prompts displayed on the Driver Information
Center (DIC). These prompts allow you to choose
various lock and unlock settings. For more information
on programming, seeDIC Vehicle Customization
on page 3-62.
2-11

Rear Door Security Locks
Your vehicle has rear door security locks. These prevent
passengers from opening the rear doors from the inside.
The rear door security
locks are located on
the inside edge of each
rear door. The rear
doors must be open
to access them. The
label showing lock
and unlock positions
is located near the lock.
To set the locks, do the following:
1. Insert the key into the security lock slot and
turn it so the slot is in the horizontal position.
2. Close the door.When you want to open a rear door when the security
lock is on, do the following:
1. Unlock the door using the remote keyless entry
transmitter, if the vehicle has one, the power door
lock switch, or by lifting the rear door manual lock.
2. Open the door from the outside.
To cancel the rear door security lock, do the following:
1. Unlock the door and open it from the outside.
2. Insert the key into the security lock slot and turn
it so the slot is in the vertical position.
Lockout Protection
If the power door lock switch is pressed when the key
is in the ignition and a door is open, all the doors
will lock and only the driver’s door will unlock. If you
close the doors, they can be locked by using the
Remote Keyless Entry (RKE) transmitter. Be sure to
remove the key from the ignition when locking your
vehicle.
This feature can be overridden by pressing the
lock button on the RKE transmitter or by pressing
the power lock switch a second time. Lock Label shown
2-12

Power Windows
{CAUTION:
Leaving children, helpless adults, or pets in a
vehicle with the windows closed is dangerous.
They can be overcome from extreme heat in
warm or hot weather and suffer permanent
injuries or even death from heat stroke.
Leaving children in a vehicle with the ignition
key is dangerous for many reasons, children or
others could be badly injured or even killed.
They could operate the power windows or other
controls or even make the vehicle move. The
windows will function with the keys in the
ignition and they could be seriously injured or
killed if caught in the path of a closing window.
Do not leave keys in a vehicle with children.
When there are children in the rear seat use the
window lockout button to prevent unintentional
operation of the windows.The power window
switches are located
on the armrest near
each window.
Press the switch to the rst position to lower the
window to the desired level. Pull the switch up
to raise the window.
Your vehicle has Retained Accessory Power (RAP)
that allows you to use the power windows once
the ignition has been turned off. For more information,
seeRetained Accessory Power (RAP) on page 2-26.
2-17

Express-Down Window
This feature is on all windows. Press the switch to
the second position and release the switch to activate
the express-down feature. To stop the window as
it is lowering, press down or pull up briey on the
switch again.
Express-Up Window
This feature is on all windows. Pull the switch up to the
second position and release the switch to activate
the express-up feature. To stop the window as it is
raising, pull up or press down briey on the switch again.
Programming the Power Windows
If the battery on your vehicle has been recharged,
disconnected, or is not working, you will need to
reprogram each power window for the express-up
feature to work. Before reprogramming, you will need
to replace or recharge your vehicle’s battery.To program each window, follow these steps:
1. With the ignition in ON/RUN, ACC/ACCESSORY,
or when Retained Accessory Power (RAP) is
active, close all doors.
2. Press and hold the power window switch until the
window is fully open.
3. Pull the power window switch up until the window
is fully closed.
4. Continue pulling the switch up for approximately
two seconds after the window is completely
closed.
The window is now reprogrammed. Repeat the process
for the other windows.Express Window Anti-Pinch Feature
If any object is in the path of the window when
the express-up is active, the window will stop at the
obstruction and auto-reverse to a preset factory position.
Weather conditions such as severe icing may also
cause the window to auto-reverse. The window
will return to normal operation once the obstruction
or condition is removed.
2-18