light CADILLAC STS V 2007 1.G Repair Manual

Passenger Airbag Status Indicator............. 245
Charging System Light.............................. 247
Brake System Warning Light..................... 248
Anti-Lock Brake System Warning Light...... 249
Low Tire Pressure Warning Light.............. 249
Traction Control System (TCS)
Warning Light........................................ 250
Engine Coolant Temperature
Warning Light........................................ 251
Engine Coolant Temperature Gage............ 251
Malfunction Indicator Lamp........................ 252
Oil Pressure Light..................................... 255
Security Light............................................ 256
Fog Lamp Light......................................... 256
Lights On Reminder.................................. 256
Cruise Control Light.................................. 256
Highbeam On Light................................... 257
Fuel Gage................................................. 257Driver Information Center (DIC).................. 258
DIC Controls and Displays........................ 258
DIC Warnings and Messages.................... 264
Other Messages........................................ 279
Audio System(s)......................................... 280
Setting the Time........................................ 281
Radio with CD........................................... 282
Using an MP3........................................... 297
XM Radio Messages................................. 303
Navigation/Radio System........................... 305
Radio Personalization................................ 305
Theft-Deterrent Feature............................. 309
Audio Steering Wheel Controls.................. 310
Radio Reception........................................ 312
Care of Your CDs..................................... 313
Care of the CD Player.............................. 313
Diversity Antenna System.......................... 314
XM™ Satellite Radio Antenna System....... 314
Section 3 Instrument Panel
176

Power Tilt Wheel and Telescopic
Steering Column
The power tilt and
telescope wheel control
is located on the
outboard side of the
steering column.
To operate the power tilt feature, move the control
up or down to tilt the steering wheel up or down.
To set the memory position, seeVehicle
Personalization on page 148andMemory Seat,
Mirrors and Steering Wheel on page 169.
To operate the power telescope feature, move the
control forward or rearward and the steering
wheel moves toward the front or rear of the
vehicle.
Heated Steering Wheel
Your vehicle may have a heated steering wheel.
The button for this
feature is located on
the steering wheel.
Press the bottom of the button to turn the heated
steering wheel on or off. A light on the button
will display while the feature is on.
The steering wheel will take about three minutes
to reach its maximum temperature.
181

Raise or lower the lever until the arrow starts to
ash to signal a lane change. Hold it there until the
lane change is complete. The lever returns to its
original position when it is released.
Rapid ashing of arrows when signaling for a turn
or lane change may be caused by a burned-out
signal bulb. Other driver’s will not see the signal.
Replace burned-out bulbs to help avoid possible
accidents. Check the fuse and for burned-out bulbs
if the arrow fails to work when signaling a turn.
SeeFuses and Circuit Breakers on page 487for
more information.
Turn Signal On Chime
If the turn signal is left on for about 1 mile (1.6 km),
a warning chime will sound and the TURN
SIGNAL ON message will appear on the Driver
Information Center (DIC) display. See “Turn Signal
On” underDIC Warnings and Messages on
page 264for more information.
Headlamp High/Low-Beam Changer
Push forward on the turn signal/multifunction
lever to change the headlamps from low to high
beam. Pull the lever back and then release it
to change from high to low beam.
If you turn the vehicle off with the high beams on,
the next time you start your vehicle the low
beams will be on.
To re-activate high beams, pull lever toward you
and then push it forward again.
This light on the
instrument panel cluster
will be on, indicating
high-beam usage.
183

Heavy snow or ice can overload the wiper motor. A
circuit breaker will stop the motor until it cools down.
Clear away snow or ice to prevent an overload.
Your vehicle (STS-V only) is equipped with a
feature that disables the wiper system when the
hood is open and your vehicle is stopped. Opening
the hood will automatically park the wipers if
they are not parked. This prevents the wipers from
interfering with hood operation. Be sure the
hood is not opened when you require the vehicle’s
wipers out of the park position, such as when
changing the wiper blades.
Rainsense™ II Wipers
If your vehicle has this feature, the moisture
sensor is mounted on the interior side of the
windshield behind the rearview mirror. It is used to
automatically operate the wipers by monitoring
the amount of moisture build-up on the windshield.
Wipes occur as needed to clear the windshield
depending on driving conditions and the sensitivity
setting. In light rain or snow, fewer wipes will
occur. In heavy rain or snow, wipes will occur more
frequently. The Rainsense™ wipers operate in adelay mode as well as a continuous low or high
speed as needed. If the system is left on for long
periods of time, occasional wipes may occur
without any moisture on the windshield. This is
normal and indicates that the Rainsense™ system
is activated.
To activate the Rainsense™ system, turn the
wiper band to delay mode and select one of the
four sensitivity levels indicated on the wiper stalk.
The position closest to off is the lowest sensitivity
setting, level one. This allows more rain or snow to
collect on the windshield between wipes. Turning
the wiper band away from you to higher sensitivity
levels increases the sensitivity of the system and
frequency of wipes. The highest sensitivity setting,
level four, is closest to low. A single wipe will occur
each time you turn the wiper stalk to a higher
sensitivity level to indicate that the sensitivity level
has been increased.
Notice:Going through an automatic car wash
with the wipers on can damage them. Turn
the wipers off when going through an
automatic car wash.
190

The mist and wash cycles operate as normal and
are not affected by the Rainsense™ function.
The Rainsense™ system can be overridden at any
time by manually turning the wiper band to low
or high speed.
When Rainsense™ is active, the headlamps will
turn on automatically. The headlamps will turn
off again once the wipers turn off if it is light
enough outside. If it is dark, they will remain on.
SeeWiper Activated Headlamps on page 215.
Notice:Do not place stickers or other items
on the exterior glass surface directly in front of
the moisture sensor. Doing this could cause
the moisture sensor to malfunction.
Windshield Washer
K(Washer Fluid):The lever on the right side
of the steering column also controls the windshield
washer. There is a button at the end of the
lever. To spray washer uid on the windshield,
press the button and hold it. The washer will spray
until you release the button. The wipers will
continue to clear the window for about six seconds
after the button is released and then stop or
return to your preset speed.
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
If the uid in the windshield washer uid reservoir
is low, the message CHECK WASHER FLUID
will appear on the Driver Information Center (DIC)
display. It will take 60 seconds after the bottle
is relled for this message to turn off. For
information on the correct washer uid mixture to
use, seeWindshield Washer Fluid on page 404
andRecommended Fluids and Lubricants on
page 516.
191

If you apply your brakes, the cruise control will
shut off.
{CAUTION:
Cruise control can be dangerous where
you cannot drive safely at a steady speed.
So, do not use your cruise control on
winding roads or in heavy traffic.
Cruise control can be dangerous on
slippery roads. On such roads, fast
changes in tire traction can cause
excessive wheel slip, and you could lose
control. Do not use cruise control on
slippery roads.
If your vehicle is in cruise control when the
Traction Control System (TCS) begins to limit
wheel spin, the cruise control will automatically
disengage. SeeTraction Control System (TCS) on
page 323andStabiliTrak
®System on page 326.
When road conditions allow you to safely use
it again, you may turn the cruise control back on.
Setting Cruise Control
{CAUTION:
If you leave your cruise control on when
you are not using cruise, you might hit a
button and go into cruise when you do not
want to. You could be startled and even
lose control. Keep the cruise control switch
off until you want to use cruise control.
1. Move the cruise control switch to on.
2. Get up to the speed desired.
3. Press in the set button at the end of the lever
and release it.
4. Take your foot off the accelerator pedal.
This light on the
instrument panel cluster
will come on while
cruise control is on.
194

Reducing Speed While Using Cruise
Control
There are two ways to reduce your speed while
using cruise control:
Press in the button at the end of the lever until
you reach the lower speed desired, then
release it.
To slow down in very small amounts, briey
press the set button. Each time you do this,
you will go about 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase your speed.
When you take your foot off the pedal, the
vehicle will slow down to the cruise control speed
you set earlier.
Using Cruise Control on Hills
How well the cruise control works on hills depends
upon the vehicle speed, load, and the steepness of
the hills. When going up steep hills, you might have
to step on the accelerator pedal to maintain the
vehicle’s speed. When going downhill, you might
have to brake to keep the vehicle’s speed down.
Applying the brake will turn off the cruise control. If
you need to apply the brake due to the grade of the
downhill slope, you might not want to attempt to use
your cruise control feature.
Ending Cruise Control
To end a cruise control session, step lightly on the
brake pedal.
Stepping on the brake pedal will end the current
cruise control session only. Move the cruise control
switch to off to turn off the system completely.
Erasing Speed Memory
When you turn off the cruise control or the
ignition, the cruise control set speed memory
is erased.
196

Approaching and Following a Vehicle
The vehicle ahead
symbol will only appear
on the HUD when a
vehicle ahead is
detected in your path.
If this symbol does not appear, or disappears
briey, Adaptive Cruise Control will not respond to
vehicles you may see ahead.
{CAUTION:
When the Adaptive Cruise Control radar is
blocked by snow, ice, or dirt, it may not
detect a vehicle ahead. Adaptive Cruise
Control may not have time to slow your
vehicle enough to avoid a collision.
CAUTION: (Continued)
CAUTION: (Continued)
Do not use Adaptive Cruise Control when
the radar is blocked by snow, ice, or dirt.
Keep your radar clean. See “Cleaning the
System” later in this section.
Adaptive Cruise Control will, automatically, slow
your vehicle down when approaching a slower
moving vehicle. It will then adjust your speed to
follow the vehicle in front at the selected follow
distance. Your speed will increase or decrease to
follow the vehicle in front of you but will not
exceed the set speed. It may apply limited braking,
if necessary. When braking is active, your brake
lights will come on. It may feel or sound different
than if you were applying the brakes yourself. This
is normal.
205

Other Messages
There are three messages that may appear on the
DIC. They are SERVICE RADAR CRUISE,
RADAR CRUISE NOT READY and CLEAN
RADAR. These messages will appear to indicate
a problem with the Adaptive Cruise Control.
SeeDIC Warnings and Messages on page 264
for more information.
Cleaning the System
The radar can become blocked by snow, ice or
dirt. If so, you may need to turn off the engine and
clean the lens. Remember, do not use Adaptive
Cruise Control in icy conditions, or when visibility is
low, such as in fog, rain or snow.
The emblem/lens is located in the center of
the grille.
To clean the emblem/lens, wipe the surface with a
soft cloth. After cleaning the emblem/lens,
engage the Adaptive Cruise Control. If you are
unable to do so, see your dealer.
Headlamps
The exterior lamp control is located in the middle
of the turn signal/multifunction lever.
O(Exterior Lamp Control):Turn the control
with this symbol on it to operate the exterior lamps.
The exterior lamp control has four positions:
O(On/Off):Turn the control to this position to
turn off all lamps and automatic lighting features
including Daytime Running Lamps (DRL) and
IntelliBeam™.
211

This is a momentary switch that springs back to the
AUTO position when released. An AUTOMATIC
LIGHTS ON message appears on the DIC when
automatic lights are enabled or an AUTOMATIC
LIGHTS OFF message appears on the DIC when
the automatic lights are disabled.
AUTO (Automatic):Turn the control to this
position to put the headlamps in automatic mode.
AUTO mode, turns the exterior lamps on and
off depending upon how much light is available
outside of the vehicle.
Due to the switch design, the automatic lights may
be disabled even if the control is in the AUTO
position.
To enable automatic lighting do any of the
following:
Turn the headlamp control from AUTO to off
and release the switch. It returns back to the
AUTO position by itself.
Turn the headlamp control from the parking
lamp position to AUTO.
Turn the headlamp control from the headlamp
position to AUTO.To disable automatic lighting do any of the
following:
Turn the headlamp control from AUTO to off
and release the switch. It returns back to the
AUTO position by itself.
Turn the headlamp control from AUTO to the
parking lamp position.
Turn the headlamp control from AUTO to the
headlamp position.
Disabling automatic lighting disables the automatic
headlamp operation, DRL, and IntelliBeam™
High-Beams (if the vehicle has them).
;(Parking Lamps):Turn the control to this
position to turn on the parking lamps together with
the following:
Sidemarker Lamps
Taillamps
License Plate Lamps
Instrument Panel Lights
5(Headlamps):Turn the control to this position
to turn on the headlamps, together with the
previously listed lamps and lights.
212