ECO mode CHERY TIGGO 2009 Service Repair Manual

Downloaded from www.Manualslib.com manuals search engine •Digit #8 The eighth digit of the VIN code represents the restraint rystem:
A represents manual safety belts.
B represents manual safety belts plus air bags in the front row.
• Digit #9 The ninth digit of the VIN code is the check digit:
It is to check accuracy of VIN record, and is made out through computation after confirming the other six-
teen digits of the VIN.
• Digit #10 The tenth VIN position represents the model year code:
5 represents the year 2005.
• Digit #11 The eleventh VIN position represents the assembly plant code:
D represents the Chery Automobile Co., Ltd.
• Digits #12, #13, #14, #15, #16, #17 The last six VIN positions represent the production sequence number.
This represents the actual production number of the vehicle.
VEHICLE IDENTIFICATION NUMBER (VIN)
01–12Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine DIAGNOSING ELECTRICAL FAILURES
Performing Efficient Electrical Circuit Diagnosis and Troubleshooting
STEPDESCRIPTION
Step 1 Obtain detailed information about the conditions and the environment when the electrical
incident occurred.
Step 2 Operate the affected system, road test the vehicle if necessary.
Verify the parameter of the incident.
If the problem cannot be duplicated, refer to “Electrical Failure Simulation Tests”.
Step 3 Gather the proper diagnostic material including the following:
•
Electrical Power Supply Routing Diagram
• System Operation Descriptions
• Applicable Service Manual Sections
• Check for any Service Bulletins
Identify where to begin diagnosis based upon your knowledge of the system operation
and the customer comments.
Step 4 Inspect the system for mechanical binding, loose connectors or wiring damage.
Determine which circuits and components are involved and diagnose using the Electrical
Power Supply Routing Diagram and Harness Layouts.
Step 5 Repair the circuit or replace the component as necessary.
Step 6 Operate the system in all modes. Verify the system functions properly under all conditions.
Confirm you have not inadvertently created an additional new incident during your
diagnosis or repair steps.
Electrical Circuit Simulation Tests
Often the symptom is not present when the vehicle is brought in for service. If possible, re-create the conditions
present at the time of the incident. Doing so may help avoid a No Trouble Found Diagnosis. The following illustrates
tests to simulate the conditions/environment under which the owner experiences an electrical incident.
The tests are broken into the seven following topics:
•
Vehicle Vibration Test
• Heat Sensitive Test
• Freezing Test
• Water Intrusion Test
• Electrical Load Test
• Cold or Hot Start Up Test
• Voltage Drop Test
NOTE :
Always get a thorough description of the incident from the customer. It is important for simulating the conditions of
the problem.
Vehicle Vibration Test
The problem may occur or become worse while driving on a rough road or when the engine is vibrating (idle with A/C
on). In such a case, check for a vibration related condition. Refer to the following vehicle areas:
Connectors & Harness
• Determine which connectors and wiring harness would affect the electrical system you are inspecting. Gently
shake each connector and harness while monitoring the system for the incident you are trying to duplicate. This
test may indicate a loose or poor electrical connection.
NOTE :
Connectors can be exposed to moisture. It is possible for a thin film of corrosion to form on the connector terminals.
A visual inspection may not reveal this without disconnecting the connector. If the problem occurs intermittently, per-
haps the problem is caused by corrosion. It is a good idea to disconnect, inspect and clean the terminals on related
connectors in the system.
01–16Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Electronic Engine Control Input & Output Device Failure Modes
NUMBER ITEMFAILURE MODECORRECTION
1 CKP•
Engine is hard to start.
• The engine RPM will be limited after the engine starts.
• The highest RPM is less than 3800.
• Excessive exhaust emissions.
• No ignition signal to the ECM.
• The tachometer does not work.
• Rough engine operation. Replace
2 CMP•
The fuel injector ON time may vary from 720 degrees to 360
degrees.
• The sensor output is not correct, the MIL light will turn on
when with the second revolution after the engine starts.
• Engine is hard to start.
• The highest RPM is less than 4000. Replace
3 APPS•
The MIL light will turn on.
• Poor acceleration.
• The engine RPM will be limited after the engine starts. Replace
4 ECT•
Engine hard to start when cold.
• Engine hard to start when hot.
• Poor driving capability.
• If the sensor circuit is shorted to power, the engine will run
under the default values.
• The temperature gauge indicates too high.
• The temperature gauge indicates too low.
• The cooling fan operates continuously on high speed.
• The high temperature warning lamp will flash when the IP
indicates low temperature. Replace
5 MAF•
The cooling fan will operate for approximately 60 seconds on
high speed after the ignition switch is turned off.
• Poor acceleration.
• Poor driving capability. Replace
6 O2 Sensor •
Poor fuel economy.
• Excessive exhaust emissions.
• Sluggish acceleration.
• Poor driving capability. Replace
7 Knock Sensor •
The engine produces an engine knock.
• Overheated engine.
• Excessive exhaust emissions.
• Poor fuel economy.
• Lack of engine power.
• Internal engine damage. Replace
8 ECM•
Unstable engine idle.
• Poor acceleration.
• Unable to start.
• High engine idle.
• The engine exhaust exceeds emission standards.
• Engine is hard to start.
• Air conditioner does not operate.
• Fuel injector control failure.
• Engine stalls out. Replace
9 Ignition Coil •
Unstable idle.
• Lack of engine power.
• Poor fuel economy

.
• Excessive exhaust emissions.
• Weak spark. Replace
GENERAL INFORMATION
03–4Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine NUMBER ITEMFAILURE MODECORRECTION
10 Fuel Injector •
Unstable idle.
• Lack of engine power.
• Poor acceleration.
• Engine will not start.
• Plugged injector. Replace
11 TPS•
Poor acceleration.
• The MIL light will turn on. Replace
12 EVAP•
The engine base fuel closed-loop control self-learning will be
shut off.
• The engine idle air control self-learning will be shut off.
• Unstable idle or high idle. Replace
13 Fuel Pump •
Noisy fuel pump operation.
• Poor acceleration.
• Engine will not start. Replace
14 MAP•
Poor acceleration.
• Unstable idle.
• Rough engine operation. Replace
15 IAT•
Intake air temperature will be equal to the coolant
temperature. Replace
16 Cooling Fan •
High engine temperature.
• Poor air conditioner performance. Replace
17 Accelerator
Sensor •
Misfire
• Poor driving capability.
• Rough engine operation. Replace
Specifications
Torque Specifications
DESCRIPTION
TORQUE (N·m)
Engine Coolant Temperature (ECT) Sensor 20
Knock Sensor 20
Oxygen Sensors 45
Crankshaft Position (CKP) Sensor 10
Camshaft Position (CMP) Sensor 7
Air Flow Sensor Bolts 5
Engine Control Module (ECM) Bolts 10
Accelerator Pedal Position (APP) Sensor 11
Electronic Throttle Control Actuator 10
Vehicle Speed Sensor 10
Manifold Absolute Pressure (MAP) Sensor 6
GENERAL INFORMATION
03
03–5Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Electronic Engine Control Input & Output Device Failure Modes
NUMBER ITEMFAILURE MODECORRECTION
1 CKP•
Engine is hard to start.
• The engine RPM will be limited after the engine starts.
• The highest RPM is less than 3800.
• Excessive exhaust emissions.
• No ignition signal to the ECM.
• The tachometer does not work.
• Rough engine operation. Replace
2 CMP•
The fuel injector ON time may vary from 720 degrees to 360
degrees.
• The sensor output is not correct, the MIL light will turn on
when with the second revolution after the engine starts.
• Engine is hard to start.
• The highest RPM is less than 4000. Replace
3 APPS•
The MIL light will turn on.
• Poor acceleration.
• The engine RPM will be limited after the engine starts. Replace
4 ECT•
Engine hard to start when cold.
• Engine hard to start when hot.
• Poor driving capability.
• If the sensor circuit is shorted to power, the engine will run
under the default values.
• The temperature gauge indicates too high.
• The temperature gauge indicates too low.
• The cooling fan operates continuously on high speed.
• The high temperature warning lamp will flash when the IP
indicates low temperature. Replace
5 MAF•
The cooling fan will operate for approximately 60 seconds on
high speed after the ignition switch is turned off.
• Poor acceleration.
• Poor driving capability. Replace
6O
2Senser •
Poor fuel economy.
• Excessive exhaust emissions.
• Sluggish acceleration.
• Poor driving capability. Replace
7 Knock Sensor •
The engine produces an engine knock.
• Overheated engine.
• Excessive exhaust emissions.
• Poor fuel economy.
• Lack of engine power.
• Internal engine damage. Replace
8 ECM•
Unstable engine idle.
• Poor acceleration.
• Unable to start.
• High engine idle.
• The engine exhaust exceeds emission standards.
• Engine is hard to start.
• Air conditioner does not operate.
• Fuel injector control failure.
• Engine stalls out. Replace
9 Ignition Coil •
Unstable idle.
• Lack of engine power.
• Poor fuel economy.
• Excessive exhaust emissions.
• Weak spark. Replace
GENERAL INFORMATION
03–230Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine NUMBER ITEMFAILURE MODECORRECTION
10 Fuel Injector •
Unstable idle.
• Lack of engine power.
• Poor acceleration.
• Engine will not start.
• Plugged injector. Replace
11 TPS•
Poor acceleration.
• The MIL light will turn on. Replace
12 EVAP•
The engine base fuel closed-loop control self-learning will be
shut off.
• The engine idle air control self-learning will be shut off.
• Unstable idle or high idle. Replace
13 Fuel Pump •
Noisy fuel pump operation.
• Poor acceleration.
• Engine will not start. Replace
14 MAP•
Poor acceleration.
• Unstable idle.
• Rough engine operation. Replace
15 IAT•
Intake air temperature will be equal to the coolant
temperature. Replace
16 Cooling Fan •
High engine temperature.
• Poor air conditioner performance. Replace
17 Accelerator
Sensor •
Misfire
• Poor driving capability.
• Rough engine operation. Replace
Specifications
Torque Specifications
DESCRIPTION
TORQUE (N·m)
Engine Coolant Temperature Sensor 20
Knock Sensor 20
Oxygen Sensors 45
Crankshaft Position Sensor 10
Camshaft Position Sensor 7
Air Flow Sensor 5
Engine Control Module 10
Accelerator Pedal Position Sensor 11
Electronic Throttle Control Actuator 10
Vehicle Speed Sensor 10
GENERAL INFORMATION
03
03–231Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Electronic Engine Control Input & Output Device Failure Modes
NUMBER ITEMFAILURE MODECORRECTION
1 CKP•
Engine is hard to start.
• The engine RPM will be limited after the engine starts.
• The highest RPM is less than 3800.
• Excessive exhaust emissions.
• No ignition signal to the ECM.
• The tachometer does not work.
• Rough engine operation. Replace
2 CMP•
The fuel injector ON time may vary from 720 degrees to 360
degrees.
• The sensor output is not correct, the MIL light will turn on
when with the second revolution after the engine starts.
• Engine is hard to start.
• The highest RPM is less than 4000. Replace
3 APPS•
The MIL light will turn on.
• Poor acceleration.
• The engine RPM will be limited after the engine starts. Replace
4 ECT•
Engine hard to start when cold.
• Engine hard to start when hot.
• Poor driving capability.
• If the sensor circuit is shorted to power, the engine will run
under the default values.
• The temperature gauge indicates too high.
• The temperature gauge indicates too low.
• The cooling fan operates continuously on high speed.
• The high temperature warning lamp will flash when the IP
indicates low temperature. Replace
5 MAF•
The cooling fan will operate for approximately 60 seconds on
high speed after the ignition switch is turned off.
• Poor acceleration.
• Poor driving capability. Replace
6O
2Sensor •
Poor fuel economy.
• Excessive exhaust emissions.
• Sluggish acceleration.
• Poor driving capability. Replace
7 Knock Sensor •
The engine produces an engine knock.
• Overheated engine.
• Excessive exhaust emissions.
• Poor fuel economy.
• Lack of engine power.
• Internal engine damage. Replace
8 ECM•
Unstable engine idle.
• Poor acceleration.
• Unable to start.
• High engine idle.
• The engine exhaust exceeds emission standards.
• Engine is hard to start.
• Air conditioner does not operate.
• Fuel injector control failure.
• Engine stalls out. Replace
9 Ignition Coil •
Unstable idle.
• Lack of engine power.
• Poor fuel economy.
• Excessive exhaust emissions.
• Weak spark. Replace
GENERAL INFORMATION
03
03–443Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine NUMBER ITEMFAILURE MODECORRECTION
10 Fuel Injector •
Unstable idle.
• Lack of engine power.
• Poor acceleration.
• Engine will not start.
• Plugged injector. Replace
11 TPS•
Poor acceleration.
• The MIL light will turn on. Replace
12 EVAP•
The engine base fuel closed-loop control self-learning will be
shut off.
• The engine idle air control self-learning will be shut off.
• Unstable idle or high idle. Replace
13 Fuel Pump •
Noisy fuel pump operation.
• Poor acceleration.
• Engine will not start. Replace
14 MAP•
Poor acceleration.
• Unstable idle.
• Rough engine operation. Replace
15 IAT•
Intake air temperature will be equal to the coolant
temperature. Replace
16 Cooling Fan •
High engine temperature.
• Poor air conditioner performance. Replace
17 Accelerator
Sensor •
Misfire
• Poor driving capability.
• Rough engine operation. Replace
Specifications
Torque Specifications
DESCRIPTION
TORQUE (N·m)
Engine Coolant Temperature Sensor 20
Knock Sensor 20
Oxygen Sensors 45
Crankshaft Position Sensor 20
Camshaft Position Sensor 10
Air Flow Sensor 8
Engine Control Module 10
Electronic Throttle Control Actuator 10
Vehicle Speed Sensor 10
Coolant Temperature Sensor (For Instrument Cluster) 14
GENERAL INFORMATION
03–444Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine DP0 Transaxle Control Module (TCM) Connector Pin-Out Table
TCM Pin-Out Table
PINCIRCUIT IDENTIFICATION PINCIRCUIT IDENTIFICATION
1 + EVS 29-
2 Flow Control Solenoid Valve (+) 30-
3 -31Shift 2
4 -32Shift 3
5 -33Shift 4
6 -34P/N Switch
7 Shift Solenoid Valve 3 35-
8 Shift Solenoid Valve 4 36Sequential (-)
9 Shift Solenoid Valve 2 37Sequential (+)
10 Shift Solenoid Valve 1 38CAN-H
11 Shift Lock 39CAN-L
12 Fluid Cooler Flow Control 40Winter Mode
13 Shift Solenoid Valve 5 41-
14 Shift Solenoid Valve 6 42MFS Switch
15 -43Brake Switch
16 Brake Switch 44-
17 -45Turbine Shaft (+)
18 -46Turbine Shaft (-)
19 CDE EVM PTG 47Secondary Shaft (-)
20 Torque Converter Lock Solenoid Valve
(CDE EVM PRSN) 48
Secondary Shaft (+)
21 -49 -
22 -50 -
23 -51 -
24 Regulated Sensor Supply 52-
25 Sensor (GND) 53Fluid Temperature Sensor (-)
26 Pressure Adjust Solenoid Valve (+EVM) 54 Fluid Temperature Sensor (+)
27 Ignition Switch 55Fluid Pressure Sensor
28 GND 56BATT
GENERAL INFORMATION
08–18Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine On Board Diagnostic Logic
•Self-diagnosis detection logic.
DTC NO. DTC DEFINITION DTC DETECTION
CONDITION DTC SET
CONDITION POSSIBLE CAUSES
22 Input speed sensor Vehicle is driving •
The Transaxle
Control Module
(TCM) will set this
DTC when the TCM
didn’t received pulse
signal from the input
shaft speed sensor
for above 1 seconds
when the vehicle is
driving for 30 km/h
at 3 or 4 gear.
• If the DTC was
set for 4 times, then
the A/T will be
locked in 3rd gear
(D gear) or shifted
to low gear when in
sports mode. •
Input shaft speed
sensor
• The retainer of
deceleration clutch
• Harness or
connectors (The
sensor circuit is open
or shorted)
• TCM
DTC Confirmation Procedure:
Before performing the following procedure, confirm that battery voltage is more than 12 V.
• Turn ignition switch off.
• Connect the X-431 scan tool to the Data Link Connector (DLC) - use the most current software available.
• Turn ignition switch on, with the scan tool, view and erase stored DTCs in the TCM.
• Start the engine and warm it to normal operating temperature.
• Drive the vehicle up to 10 km/h or more.
• With the scan tool, select view DTC and data stream.
• If the DTC is detected, the DTC condition is current. Go to Diagnostic Procedure - Step 1.
• If the DTC is not detected, the DTC condition is intermittent (See Diagnostic Help and Intermittent DTC Trou-
bleshooting in Section 08 Transaxle & Transfer Case for more information).
NOTE :
While performing electrical diagnosis & testing, always refer to the electrical schematics for specific circuit
and component information.
DIAGNOSIS & TESTING
08–164Chery Automobile Co., Ltd.