set clock CHEVROLET CAMARO 1967 1.G Chassis Owner's Manual

STEERING 9-10

SECTOR SHAFT SEAL REPLACEMENT

A faulty seal may be replaced without removal of

steering gear from car by removing pitman arm as out-

lined under Maintenance and Adjustments--Steering Gear

Adjustments and proceed as follows:

1.
Loose lash adjuster lock nut and turn lash adjuster

screw several turns counterclockwise.

2.
Remove three cap screws holding side cover to gear

bushing.

3.
Pull side cover and sector shaft from gear housing

as a unit. Do not separate side cover from sector

shaft.

4.
Pull sector shaft seal from gear housing using

hooked tool or pliers.

5. Coat new seal with chassis grease and position in

sector shaft bore.

6. Place a socket or piece of pipe of suitable diameter

on top of seal and drive seal into bore by tapping

pipe or socket with soft hammer.

7. Install sector shaft side cover assembly, being care-

ful not to damage new seal with splines on end of

shaft; splines may be wrapped with a few turns of

tape to prevent this.

8. Install new side cover gasket and align side cover on

gear housing and install cap screw.

9. Perform steering gear adjustment and install pitman

arm as outlined under Maintenance and Adjustments.

STEERING COLUMN

All models are equipped with new energy absorbing

steering columns. The columns are of five basic designs

as follows:

1.
Syncromesh. The syncromesh column is used on

models with standard, column mounted, conventional

shift levers. The shift tube, within the outer mast

jacket, includes two lower shift levers for connection

to the transmission control linkage.

2.
Automatic and floor shift. This column is used on

models equipped with column mounted powerglide

shift levers, or models with floor shift. If the ve-

hicle has the column mounted powerglide shift con-

trol, the inner shift tube has a single lower shift

lever for connection to the transmission control

linkage. On floor shift models, no lower shift levers

are present on the shift tube.

3.
Tilt wheel option. The upper end and steering shaft

of this column is specially designed to accommodate

the optional tilt steering wheel.

4.
Standard Corvette Column. The standard Corvette

column is similar in design to the Automatic and

Floor Shift column used on other models, except

no shift tube is used. Other differences are pointed

out in the disassembly and assembly procedures for

Standard Corvette column.

5. Telescopic wheel option. The upper end and steering

shaft of this column is specially designed to ac-

commodate the optional telescoping steering wheel.

To perform service procedures on steering column

upper end components, it is not necessary to remove the

column from the vehicle. The steering wheel, horn com-

ponents, turn signal switch, upper housing with bearing,

shift control lever, hazard warning knob, and upper shift

bowl may all be removed with the column remaining in

the vehicle. When servicing the above components, omit

the removal procedure and proceed with the applicable
disassembly procedures. Because of the numerous dif-

ferences in steering column types, be sure to refer to the

set of instructions below which apply to the exact column

to be serviced:

CAUTION: The outer mast jacket, shift tube, _

steering shaft, and instrument panel column

mounting b
racket

are designed as energy ab-

sorbing units. Because of the design of these

components, it is absolutely necessary to handle

the column with care when performing any serv-

ice operation required. Avoid hammering, jar-

ring, dropping, or leaning on any portion of the

column.

Removal

1.
Disconnect steering column harness at connector.

Disconnect neutral safety switch and back-up lamp

switch connectors if so equipped.

Remove steering wheel as outlined in this section.

Remove nuts and washers securing flanged end of

column to steering gear. On Chevy H models, re-

move nut and clamp bolt securing lower end of steer-

ing column to steering gear.

Disconnect transmission control linkage, if so

equipped, from lower column shift tube, levers.

Chevrolet and Chevy II only: Remove screws at-

taching upper and lower mast jacket covers together.

On Chevrolet, remove screws attaching lower cover

to instrument panel (figs. 15 and 18). Remove lower

cover.

Chevelle only: Remove screws securing mast jacket

trim cover to instrument panel and remove cover

(fig. 15).

Corvette, only: Remove screws securing escutcheon

to instrument panel. Remove screws securing upper

and lower covers together and remove covers.

On Chevrolet and Chevelle columns with Powerglide

shift levers, loosen set screw at six o'clock position

at bottom of column and remove the transmission

shift indicator pointer (fig. 15).

9. Chevrolet only (fig. 19):

a. Remove screws securing cover trim to dash

panel and remove cover trim.
2.

3.

4.

5.

6.

7.

8.

Fig.
18—Mast Jacket Cover Attachments—Chevy II

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-4

b.
hand lamp until the string is positioned over the

crossarm centerline. Turn the screw clockwise

in making the final adjustment to take up play in

the headlamp mechanism.

Repeat the above procedure on the right-hand

lamp to complete the horizontal adjustment of the

headlamps.

VERTICAL ADJUSTMENT

8. a. Numeral "2" (fig. 5) should appear in the "down"

window of each aimer. If not, loosen knob at

underside of aimer arm and slide back and forth

until the numeral does appear.

NOTE:
This setting will give a 2" drop of the

headlamp high beam spot centerline on a screen

placed 25 feet forward of the vehicle. Check

state laws for proper vertical setting.

b.
Turn headlamp vertical aim screw (fig. 5) on left-

hand unit counter-clockwise until the bubble is at

the inner end of the glass tube. Then turn screw

clockwise until bubble is centered in tube.

c. Repeat this procedure on right-hand headlamp

unit to complete vertical adjustment of lamps.

9. Recheck the string at the ends of each crossarm for

correct setting and the bubble on each aimer for

centered position.

10.
Remove the aimers by pulling on the suction cup tabs

through the openings in the aimers (fig. 6).

11.
With headlamps properly aimed, replace headlamp

bezels.

HOW TO SELECT A LEVEL AIMING AREA

1.
Select area you believe to be level.

2.
Remove headlamp bezels and install Aimers on each

headlamp (fig. 3) making sure aiming lugs engage

smoooth inner ring of the Aimer.
"
To install Aimer,

press firmly on the knob extending out from the cen-

ter of the Aimer base. This forces the suction cup

into place on the Sealed Beam unit.:

3.
Loosen the slider knob beneath the aimer arm and

set the numeral "2" in the DOWN view window (fig.

7).
Back vertical lamp adjustment out on each lamp

until bubble is outside of black line of vial, then cen-

ter bubble in between black line of vial by turning

clockwise.
VERTICAL AIMING SCREW

VIEW WINDOWS

BUBBLE

Fig.
6 - Removing Aimer from Headlamp
Fog.
7- Selecting Level Aiming Area

4.
After botli bubbles are centered, turn the car around

end for end, making sure the tires are in the spots

made on the floor before the car was moved.

.5.
If the bubbles are still within the two outside black

marks on the vials, the floor is level enough to use

the Aimer as it comes from the factory.

NOTE:
A quick level check can be made by

using the T-3 Safety-Aimer as a level. Use

with a true eight to ten foot two by four as an

extension. Make sure pads on base of Aimer

are used. Place the board where you expect the

wheels to be and take readings as outlined above.

6. If either bubble moves outside the black lines of the

vial there is too much slant to the floor. Try driving

the car in at different angles onto the aiming area.

If bubbles can
not
be centered follow procedure under

"How to Compensate for Unlevel Floor."

NOTE:
When level portion of floor is obtained,

mark tire spots on floor so spots can be used

next time without calibrating Aimer.

TO COMPENSATE FOR UNLEVEL FLOORS

If your floor is not level within the limits specified, the

T-3 Aimer can be calibrated to compensate for the error

in the floor. Follow this procedure with both aimers.

1.
Drive the car onto the area for which you wish to

compensate the aimers, and install the aimers in

place on the headlamps.

2.
Loosen knob beneath the aimer arm and move the

slider until the bubble is centered.

3.
Record the numeral in the view window. (This nu-

meral is to be used only for recalibration.)

4.
Move the slider to a position halfway between this

recorded numeral and the numeral "2" in the
DOWN

window. (This numeral is used only in recalibration

and not for headlamp aiming.)

5.
Recalibrate aimers by turning screw shown in Figure

8 until the bubble is centered.

6. The T-3 Aimers are now calibrated for the selected

area. All future aiming must be done in the same

area and with the car pointed in the same direction.

Mark the tire spots on the floor so that other vehi-

cles can be located in the same position.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-19

VIEW A
•CONTACT SUPPORT

DRIVE SLOT IN LINE

WITH HOLE IN SWITCH

PAWL
CONTACT POINT B

CONTACT SUPPORT

DRIVE SLOT IN LINE

WITH HOLE IN SWITCH

FLOOR SHIFT

(EXCEPT CAMARO)
COLUMN SH

Fig.
31 - Neutral Safety Switches

PARKING BRAKE ALARM SWITCH REPLACEMENT

Corvette (Fig. 33)

1.
Remove seat belt retainer and parking brake cover

assembly from center console.

2.
Disconnect wire from brake alarm switch.

3.
Remove retaining screw and switch from

reinforcement.

4.
Position new switch to reinforcement and install re-

taining screw.

5. Connect switch wire and check operation of switch.

6. Install cover and seat belt retainer assembly.

Chevrolet, Chevelle, Chevy II and Camaro (Fig. 34)

1.
Disconnect wiring connector at switch terminal.

2.
Remove nut and lock washer or retaining bolt and

disengage switch from brace.

3.
To install, reverse removal procedure.

INSTRUMENT PANEL COMPARTMENT

LAMP/SWITCH REPLACEMENT

1.
Disconnect battery ground cable.

2.
Reach into glove box, depress bulb in end of switch
and turn counterclockwise to remove bulb.

3..
Remove switch from socket. Carefully detach wire

and terminal from switch.

NOTE:
On some model switches, the wire and

terminal cannot be detached from the switch

making it necessary to cut and splice the switch

wire.

4.
Insert wire and terminal into new switch.

5. Push switch into place and install bulb by setting it in

place, depressing and turning it clockwise.

CIGARETTE LIGHTER REPLACEMENT

Chevrolet, Chevy II, Camaro and Corvette (Fig. 23)

1.
Disconnect battery ground cable.

2.
Disconnect wire connector at rear of lighter unit

under dash.

3.
Remove retainer from rear of housing assembly and

disengage lighter unit from panel.

4.
To install, reverse removal procedure.

Chevelle (Fig. 35)

1.
Disconnect battery ground cable.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-24

1.
Temperature Gauge

2.
Instrument Cluster Lamp

3.
R.H. Directional Indicator

4.
Ammeter Gauge
Fig. 39- Optional Gauge Cluster

5. Fuel Gauge

6. L.H. Directional Indicator

7. Tachometer

8. "Brake" Indicator

9. "Bright" Indicator
10.
Oil Pressure Fitting

11.
Chassis Harness Connector

12.
Clock Assembly

13.
Printed Circuit

NOTE:
Observe carefully the stack up of the

internal parts of the fuel gauge assembly.

5. To install, reverse removal procedure.

CLOCK OR TACHOMETER REPLACEMENT

NOTE:
The tachometer is a self-contained, all

transistor unit requiring very little service

other than keeping the terminal nuts clean and

tight. The unit is not serviceable and must be

replaced, if defective.

1.
Remove instrument cluster as previously described

in this section.

2.
For clock replacement, remove clock set shaft knob

at front of console.

3.
Remove cluster lamps from cover, circuit attaching

screws, and terminal nuts at circuit to gauge attach-

ing points.

4.
Move printed circuit away from gauge and remove

screws retaining
•_
gauge or clock to the cluster

housing.
•5.
Remove unit, from housing and cover plate from

gauge unit.

6/To install, reverse removal procedure.

AMMETER TEMPERATURE AND OIL PRESSURE

GAUGES REPLACEMENT

1.
Remove instrument cluster as previously described

iii this section.

2.
Remove instrument lamps, attaching screws or nuts

and wiring connections as required.

3.
Remove gauge assembly backing plate retaining

screws and remove gauge assembly from cluster

housing.

4.
Remove terminal nuts and/or screws retaining gauge

to the backing plate and separate plate from the

gauge.
•

5. To install, reverse removal procedure.

OIL PRESSURE INDICATOR

If the light does not come on when the ignition switch is

turned on, or if the light comes on and remains on after

the engine is started, one or more of the following condi-

tions is indicated:

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-27

Fig.
41 - Instrument Panel Installation — Chevelle

terminals from rear of cluster assembly (figs. 43

and 44).

12.
Remove four screws retaining upper section of dus-

ter housing to panel and remove cluster from the in-

strument panel and to a suitable working area for

necessary service (fig. 42).

Installation

1.
Position cluster assembly to rear of panel and install

four upper retaining screws.

2.
Connect cluster lamps, wiring connectors and wiring

harness assembly to the cluster assembly.

3.
Position instrument panel assembly into console

(hold panel at center and install center screws) and

install upper and lower retaining screws.

NOTE:
At this point temporarily reconnect

battery and check operation of cluster.

4.
Working under the console, install four lower screws

retaining lower section of cluster cover to rear of

panel.

5. Install radio brace screw at rear of radio.

6. Connect speedometer cable to speedometer and speed

warning device control knob.

7. Install A/C distributor duct and connect A/C hoses to

duct (if so equipped).

8. Install mast jacket upper support clamp.

9. Position steering shaft in the steering coupling and

install retaining bolt.

10.
Tighten mast jacket lower clamp (refer to Steering,

Section 9 for spring tension adjustment).

11.
Connect battery ground cable.

FUEL GAUGE AND/OR AMMETER

REPLACEMENT

1.
Disconnect battery ground cable.

2.
On air conditioned models, disconnect hose and re-

move air outlet from panel.

3.
Disconnect wiring connectors and cluster lamps from

rear of gauge assembly.

4.
Remove mounting plate retaining screws (3) and re-
move fuel gauge from rear of cluster housing.

5. Remove terminal nuts (3) securing gauge to template

and replace gauge.

6. To install, reverse the removal procedure.

CLOCK REPLACEMENT

1.
Disconnect battery ground cable.

2.
Remove clock set shaft knob retaining nut and knob.

3.
Disconnect wiring connector at clock terminal and

cluster lamp from clock housing. On A/C models,

disconnect hose from air distributor duct.

4.
Remove two screws retaining clock housing to

cluster cover and remove clock.

5. To install, reverse removal procedure.

SPEEDOMETER REPLACEMENT

1.
Disconnect battery ground cable.

2.
Remove instrument cluster assembly as previously

outlined in this section.

3.
Remove screws (8) attaching cover to rear of cluster

housing.

4.
Remove two screws attaching speedometer assembly

to cluster cover and carefully remove speedometer

head.

NOTE:
Servicing of the speedometer assembly

should be performed by an authorized
AC
speed-

ometer service station.

5. To install, reverse removal procedure.

SPEEDOMETER CABLE

Replacement or Lubrication

1.
Disconnect the speedometer cable from the speedom-

eter head. Remove the old cable by pulling it out

from speedometer
, end
of conduit.

NOTE:
If old cable is broken it may be neces-

sary to remove lower piece from transmission

end of conduit.

2.
Lubricate the lower 3/4 of cable with speedometer

cable lubricant and push the cable into the conduit.

Connect the upper end to the speedometer head and

road test vehicle for proper speedometer operation.

Fig.
42 - Instrument Cluster Installation

CHEVROLET CHASSIS SEtVKE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-32

Fig.
47-
Instrument Clyster Wiring

1.
Instrument Cluster Bulb

2.
R.H. Directional Indicator

3. Bright Indicator

4.
Gen Indicator
5. Temp Indicator

6. Oil Indicator

7. L.H. Directional Indicator
8. Fuel Gauge Connector

9. Instrument Panel Wiring

Harness
10.
Clock Assembly (11700-800)

11.
Cover (exc. 11700-800)

12.
Plate (exc. 11700-800)

13.
Brake Alarm
indicator

wise wiring and lamp connections may be

damaged."~ ' ""

6. To install, position cluster to console opening and

connect all wiring and lamp connections.

7. Position cluster in console and attach speedometer

cable to the speedometer head.

8. Install eight screws retaining cluster to console.

9. Install mast jack upper clamp assembly.

10.
Connect battery ground cable and check operation of

instruments and gauges.

FUEL GAUGE REPLACEMENT

1.
Disconnect battery ground cable.

2.
Disconnect cluster lamp and wiring harness connec-
5.
tions at rear of gauge.

Remove two screws retaining gauge to rear of

cluster housing and remove gauge from housing.

Remove terminal nuts attaching gauge unit to cover

plate and remove unit, from plate.

To install, reverse the removal procedure*

CLOCK REPLACEMENT

1.
Disconnect battery ground cable.

2.
Remove clock set shaft, knob retaining screw and

knob from set shaft.

3.
Disconnect wiring and lamp connections "from rear

o£ clock.

4.
Remove two screws attaching clock to rear of hous-

ing and remove clock from cluster housing.

CHevnou-r ousst

ELECTRICAL-BODY AND CHASSIS 12-34

5. To replace, reverse the removal procedure.

SPEEDOMETER REPLACEMENT

1.
Remove instrument cluster as previously described

in this section.

2.
Remove clock set shaft knob.

3.
Remove eight screws securing cluster housing to

bezel trim panel. Separate parts carefully observing

stack up of parts.

4.
Remove two screws securing speedometer head to

rear of cluster housing.

NOTE:
Servicing of the speedometer head

should be performed by an authorized AC Speed-

ometer Service Station.

5. To install, reverse the removal procedure..

SPEEDOMETER CABLE

Replacement or Lubricatibn

1.
Disconnect the speedometer cable from the speed-

ometer head. Remove the old cable by pulling it out

from speedometer end of conduit.

NOTE:
If old cable is broken it may be neces-

sary to remove lower piece from transmission

end of conduit.

2.
Lubricate the lower 3/4 of cable with speedometer

cable lubricant and push the cable into the conduit.

Connect the upper end to the speedometer head and

road test vehicle for proper speedometer operation.

INDICATOR LIGHT REPLACEMENT

To replace any indicator or cluster bulb, unsnap the

proper socket from rear of instrument cluster, remove

and replace bulb, and reinsert unit into rear of cluster

housing.

OIL PRESSURE INDICATOR

If the light does not come on when the ignition switch
is turned on, or if the light comes on and remains on

after the engine is started, one or more of the following

conditions is indicated:

• Low oil pressure

• High engine temperature

• Defective wiring or switch

Switch Replacement

1.
Disconnect wiring harness connector from sender

unit terminal (located in block above starter on

L-6 engines and at left front of distributor on V-8

engines).

2.
Remove sender unit, replace with new unit, and

; check operation.

GENERATOR INDICATOR

1.
Ignition on, engine not running and telltale light off.

a. Indicator bulb burned out, replace bulb.

b.
Open circuit or loose connection in the telltale

light circuit.

2.
Telltale light stays on after engine is started.

a. If indicator light does not go out at engine idle

speed, refer to Charging Systems under Engine

Electrical, Section 6Y.

TEMPERATURE (COOLING SYSTEM) INDICATOR

The temperature indicator circuit consists of two re-

motely located units, indicator gauge and engine sender

unit. The indicator gauge on all models uses a single

red light to indicate an overheated engine condition.

Engine Sender Unit Replacement

1.
Drain engine cooling system to a level below unit.

2.
Remove sender unit (located in the inlet manifold

near water pump housing on V-8 engines and in the

cylinder head near an exhaust port on L-6 engines)

and replace with new unit.

3.
Refill cooling system and check operation of unit.

CORVETTE INSTRUMENTS AND GAUGES

INDEX

Page

General Description ., 12-34

Service Operations . 12-35

Instrument Cluster ., 12-35

Fuel Gauge 12-35
Speedometer/Tachometer Service. 12-35

Temperature Gauge 12-35

Ammeter/Oil Pressure Gauges 12-35

GENERAL DESCRIPTION

All Corvette instruments and gauges are conveniently

located in the dash-mounted cluster. The entire cluster

is removable to permit servicing of the various instru-

ments and gauges. The indicator and cluster illuminating

bulbs may be replaced without removing the cluster from

the panel.
Regular maintenance is not required on the instrument

cluster or its components other than maintaining clean

and keeping the speedometer and tachometer cables

properly lubricated.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-41

HAZARD WARNING

SWITCHES

Fig.
55- Directional Signal Switches

erating six to eight lamps simultaneously depending ve-

hicle series and model.

DIRECTIONAL SIGNAL SWITCH REPLACEMENT

All steering columns except tilt and telescoping.

Chevrolet, Chevelle, Chevy II and Camaro (Fig. 56)

1.
Disconnect battery ground cable.

2.
Disconnect signal switch wiring from chassis har-

ness at multiple connector under instrument panel.

3.
Remove steering wheel assembly as outlined in Sec-

tion 9, Steering.

4.
Remove shift lever roll pin and shift lever from

column (if applicable).

5. Push in hazard warning switch knob and unscrew

knob.
Remove switch lever arm.

6. On Chevy U and Camaro models equipped with auto-

matic transmission remove column mounted dial in-

dicator housing and lamp assembly (if applicable).

7. Remove mast jacket lower trim cover retaining

screws and remove trim cover(s).

8. On Chevrolet and Chevelle models equipped with

automatic transmission loosen set screw and remove

quadrant dial pointer (if applicable).

9. Remove retaining
"C"
ring from upper steering shaft

using snap ring remover Tool J-22569 (Refer to

Steering, Section 9). Slide thrust and wave washers

from steering shaft.
10.
Loosen three signal switch mounting screws until

assembly can be rotated counterclockwise.

NOTE:
Do not remove three screws from as-

sembly until unit is on the bench.

11.
Rotate switch assembly counterclockwise and pull

unit from top of mast jacket. Allow unit to hang

from end of column.

Fig.
56 - Standard Steering Column

CHEVROLET CHASSIS SERVICE

SPECIFICATIONS

HEATING
AND AIR
CONDITIONING

SECTION
1A

Compressor

Make Frigidaire

Type
. 6
Cylinder Axial

Displacement

Four-Season
12.6
Cu.
In.

Universal
and
Ail-Weather
.... .10.8 Cu. In.

Rotation Clockwise

Compressor Suction
and
Discharge

Connector Bolt Torque
.......
25 ft lbs.

Compressor Clutch Coil

Ohms
(at
80°F.).
4.18-4.38

Amps
(at
80°F.)
2.86 @ 12
Volts

Torques

Rear Head
to
SheU Stud
Nut 23 lb. ft

Shaft Mounting
Nut 15 lb. ft

Belt Tension.
See
Tune-Up Chart
System Capacities

Refrigerant
R-12

Four-Season
and
Comfortron

Systems.
............
3 lbs., 12 oz.

Universal Systems

Chevrolet, Chevelle,
and
Camaro.
... 3 lbs.

Chevy
n 2 lbs. 8 oz.

All-Weather System
2 lbs. 8 oz.

Compressor
Oil 525
Viscosity

All Systems
11 oz.

Fuses

Comfortron Systems
.

Four-Season Systems
.

Universal Systems
. .

All-Weather System.
.
Fuse

Block

25
amp.

25
amp.

25
amp.

25
amp.
In

Line

30
amp.

30
amp.

20
amp.

20
amp.

SECTION
3

WHEEL ALIGNMENT SPECIFICATIONS (Vehicle
dt
Curb Weight)

Caster*

Camber*

Steering Axis

Inclination

tToe-In (Total)

Wheel Bearing

Adjustment

Preload

End Movement
Chevrolet

Pos.
3/4° ± 1/2°

Pos.
1/4° ± 1/2°

7-1/2° ± 1/2°

@l/8"
to 1/4"

12 ft lbs.

zero

.001"
to .008"
Chevelle •

(SS and El Camino)

Neg. 1/2° ± 1/2°

(All others)

Neg. 1° ± 1/2°

Pos.
1/2° ± 1/2°

8-1/4° ± 1/2°

1/8" to 1/4"

12 ft lbs.

zero

.001"
to .008"
Chevy n

Pos.
1° ± 1/2°

Pos.
1/2° ± 1/2°

7° ± 1/2°

1/4" to 3/8"

12 ft lbs.

zero

.000"
to .004"
Corvette

Pos.
1° ± 1/2°

Pos.
3/4° ± 1/2°

7° ± 1/2°

3/16" to 5/16"

12 ft lbs.

zero

.001"
to .008"
Camaro

Pos.
1/2° £ 1/2°

Pos.
1/4° ±1/2°

8 3/4° ± 1/2°

1/8" to 1/4"

12 ft lbs.

zero

.001"
to .008"

•Must not vary more than 1/2° from side to side.

@Toe-In (Total) should be 5/16" to 7/16" after rebuild using new bushings and ball joints.

tAdjust Toe-in with steering gear on straight ahead location after camber and caster have been set Any change

in caster and camber settings will affect toe; always recheck and set toe to specifications.

LET CHASSIS SERVICE MANUAL