clock CHEVROLET CAMARO 1967 1.G Chassis Owner's Guide

STEERING 9-2

Fig.
1—Cover
Attaching Bolts—Chevy li Shown

ADJUSTMENTS

STEERING
GEAR

Before any adjustments are made to the steering gear

in an attempt to correct such conditions as shimmy,

loose or hard steering etc., a careful check should be

made of front end alignment, shock absorbers, wheel

balance and tire pressure for possible cause.

Correct adjustment of the steering gear is very im-

portant. Perform adjustments following the sequence

listed below,

1.
Remove pitman arm nut and mark relation of pitman

arm position to sector shaft. Remove pitman arm

with Tool J- 6632 as shown in Figure 2.

2.
Loosen the pitman shaft lash adjuster screw locknut

and turn the adjuster screw a few turns in a counter-

clockwise direction (fig. 3). This removes the load
Fig. 2—Removing Pitman Arm

imposed on the worm bearings by the close meshing

of rack and sector teeth. Turn steering wheel gently

in one direction until stopped by gear, then back away

about one turn.

CAUTION: Do not turn steering wheel hard

against stops when steering relay rod is discon-

nected as damage to ball guides may result.

3.
All except Corvette and telescopic columns:

a. Disconnect steering column harness at chassis

wiring connector plug.

b.
Remove horn cap or ornament and using an inch

pound torque wrench and socket on steering wheel

nut, measure torque required to keep the wheel

in motion.

LASH ADJUSTER

SCREW

LOCK NUT

WORM BEARING

ADJUSTER
\

WORM

ADJUSTER

Fig.
3—Steering Gear Adjustment Points

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-3

Fig.
4-Checking Wheel PuI!-Corvette

c. If torque does not lie within limits given in speci-

fications at rear of manual, adjustment is

necessary.

4.
Corvette and telescopic columns:

a. Use Tool J-5178 to measure.pull at rim of wheel

required to keep wheel in motion (fig. 4).

b.
If pull does not lie within limits given in specifi-

cations in rear of manual, adjustment of worm

bearings is necessary.

NOTE:
If vehicle is equipped with a tilt steer-

ing column, it will be necessary to disconnect

the steering coupling to obtain a torque reading

of the steering column. This torque should then

be subtracted from any reading taken on the

gear.

5. To adjust worm bearings, loosen worm bearing ad-

juster locknut and turn worm bearing adjuster shown

in Figure 3 until there is no perceptible end play in

worm. Check pull at steering wheel, readjusting: if

necessary to obtain proper pull. Tighten locknut and

recheck pull. If the gear feels "lumpy" after adjust-

ment of worm bearings, there is probably damage in

the bearings due to severe impact or to improper

adjustment and the gear must be disassembled for

replacement of damaged parts.

6. After proper adjustment of worm is obtained and all

mounting bolts securely tightened, adjust lash ad-

juster screw. First turn the steering wheel gently

from one stop all the way to the other, carefully

counting the total number of turns. Then turn wheel

back exactly half way, to center position. Turn lash

adjuster screw clockwise to take out all lash in gear

teeth, and tighten locknut. Check pull at steering

wheel taking highest reading as wheel is turned

through center position. See specifications in rear of

manual for proper sector lash adjustment. Readjust

if necessary to obtain proper pull.
NOT MORE THAN

T/a INCH FROM

CENTERLINE

Fig.
5—Steering Wheel Alignment

NOTE:
If maximum specification is exceeded,

turn las£ adjuster screw counterclockwise, then

come up on adjustment by turning the adjuster in

a clockwise motion.

7. Tighten locknut then recheck pull, as it must lie be-

tween specified readings.

Fig.
6—Adjusting Steering Ratio—Corvette

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-4

8. Reassemble pitman arm to sector shaft, lining up

marks made during disassembly. Refer to torque

specifications at rear of manual for correct torque

value.

9. Install horn cap or ornament and connect steering

column harness at chassis connector.

NOTE:
Chevy.n models are equipped with a

shim at the frame to steering gear mounting

bolts.
Shims may be removed or installed as

required for proper steering gear alignment.

STEERING WHEEL ALIGNMENT AND

HIGH POINT CENTERING

1.
Set front wheels in straight ahead position. This can

be checked by driving vehicle a short distance on a

flat surface to determine steering wheel position at

which vehicle follows a straight path.

2.
With front wheels set straight ahead, check position

of mark on wormshaft designating steering gear high

point. This mark should be at the top side of the shaft

at 12 o'clock position and lined up with the mark in

the coupling lower clamp.

3.
If gear has been moved off high point when setting

wheels in straight ahead position, loosen adjusting

sleeve clamps on both left and right hand tie rods,

then turn both sleeves an equal number of turns in

the same direction to bring gear back on high point.

CAUTION: Turning the sleeves an unequal
number of turns or in differential directions will

disturb the toe-in setting of the wheels.

4.
Readjust toe-in as outlined in Section 3 (if necessary).

5. With wheels in a straight ahead position and the

steering gear on highpoint, check the steering wheel

alignment by measuring the distance from each hori-

zontal spoke to the horizontal centerline of the

steering wheel (fig. 5). If the horizontal spokes are

over 1-1/8 inches from the horizontal position the

wheel should be removed and centered. (See steering

wheel removal in this section.)

TOE-IN ADJUSTMENT

Adjust the steering linkage for proper toe-in setting as

outlined in Section 3.

CORVETTE STEERING RATIO (Fig. 6)

The Corvette steering ratio may be changed as follows:

CAUTION: Do not use the rearward hole in the

steering arm with power steering equipment or

interference may result.

1.
Remove tie rod ball stud nut at steering arm and

disconnect tie rod from steering arm.

2.
Move tie rod end to forward hole for 17.6:1 ratio

(fast ratio) or rear hole for 20.2:1 ratio (standard

ratio).

3.
Install tie rod stud nut and tighten securely. Repeat

operation on opposite steering arm.

COMPONENT REPLACEMENT AND REPAIRS

STEERING WHEEL

REGULAR PRODUCTION (Fig. 7)

Removal

1.
Disconnect steering column harness from chassis

wiring harness at connector (fig. 8).

2.
Pull out horn button cap or center ornament and

retainer.

3.
Remove three screws from the receiving cup.

4.
Remove the receiving cup, belleville spring, bushing,

and pivot ring.

5. Remove the steering wheel nut and washer.

6. Using Tool J-2927, install centering adapter on

steering shaft, thread puller anchor screws into

threaded holes provided in steering wheel. Turn

center bolt of tool clockwise to remove steering

wheel (fig. 9).

Installation

CAUTION: Direction signal control assembly

must be in "neutral position when assembling

steering wheel to prevent damage to cancelling

cam and control assembly.

1.
With directional cancelling cam and horn contact as-

sembly in place, set wheel onto steering shaft.
Fig. 7—-Regular Wheel and Horn Attachments

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-5

Fig.
8—Steering Column Wiring Connector

Secure with washer and nut. Refer to torque speci-

fications at rear of manual for correct torque values.

Install belleville spring (with dish of spring up), pivot

ring, bushing and receiving cup with screws.

Install retainer and horn button cap or center

ornament.

Connect steering column harness to chassis wiring

connector.

Fig.
9—Removing Steering Wheel with J-2927
Fig.
10—Simulated Wood Steering Wheel and Attaching Parts

SIMULATED WOOD (Fig. 10)

Removal

1.
Disconnect steering column harness from chassis

wiring harness at connector.

2.
Remove horn cap assembly by pulling up.

3.
Remove contact assembly attaching screws and re-

move contact assembly.

NOTE:
If steering wheel only is to be replaced,

perform step 4. If directional signal cancelling

cam is to be replaced, omit step 4 and proceed

with steps 5 and 6.

4.
Remove remaining screws from steering wheel and

remove wheel from hub assembly.

5. Remove steering wheel nut and washer.

6. Using Tool J-2927, install centering adapter on

steering shaft, thread puller anchor screws into

threaded holes provided in hub assembly. Turn

center bolt of tool clockwise to remove hub

assembly.

Installation

CAUTION: Directional signal control assembly

must be in neutral position when assembling hub

assembly to prevent damage to cancelling cam

and control assembly.

1.
With directional cancelling cam and horn contact in

place, install hub assembly on steering shaft. Secure

with washer and nut. Refer to torque specifications

at rear of manual for correct torque value.

2.
Attach steering wheel to hub assembly using the six

attaching screws and tighten securely.

3.
Place horn contact on steering wheel and attach with

three screws. Tighten securely.

4.
Snap horn button in place.

5. Connect steering column harness to chassis wiring

connector.

CORVETTE TELESCOPING (Fig. 11)

Removal

1.
Disconnect steering column harness at wiring

connector.

2.
Pry off horn button cap.

3.
Remove three screws securing horn contact to spacer

and hub.

4.
Remove two screws securing lock screw to lock

knob,
and remove lock screw, lock knob, and spacer.

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-8

DIAL

UPPER COVER

FASTENER

CHEVROLET
SCREW

CHEVELLE

Fig.
15—Powerglide Indicator Connection—Chevrolet and Chevelle

6.
Chevrolet and Chevelle only:

a. Remove lower mast jacket cover (fig. 15).

b.
If vehicle is equipped with Powerglide, remove

indicator pointer wire by removing screw from

six o'clock position at bottom of mast jacket (fig.

15).
Work indicator wire out of position and

remove.

Remove instrument panel column mounting bracket

attaching hardware and remove bracket.

CAUTION: Do not allow steering column to

hang down from dash panel area or distortion to

column will result. When instrument panel

mounting bracket is removed, be sure column is

supported in its normal position.

NOTE:
The following step requires two men,

one in the driver's seat and one at engine

compartment.

8

Lift steering column upward enough to permit re-

moval of steering coupling from steering gear.

Mechanic at engine compartment can pilot column

shift levers, if so equipped, through dash panel open-

ing as column is listed. If it is necessary to leave

the vehicle at this point, place steering column in

correct mounted position and loosely install instru-

ment panel mounting bracket to support column.

9. Remove steering coupling from vehicle.

Installation

1.
Lift steering column enough to provide clearance and

loosely install steering coupling on steering gear

shaft. Be sure column is supported in its normal

mounted position at all times when not moving for

clearance. Mechanic at engine compartment can

pilot column shift levers through dash panel opening

as column is moved.

2.
Slide steering coupling into correct installed position

and install clamp bolt (fig. 12).
3.
Secure steering coupling to flanged end of steering

column with washers and nuts. Maintain coupling ad-

justment shown in Figure 16.

4.
Install instrument panel column mounting bracket.

Refer to torque specifications at rear of manual for

correct torque values.

5. Chevrolet and Chevelle only:

a. If vehicle is equipped with Powerglide, work shift

indicator pointer wire into position on column and

secure with screw at six o'clock position at bot-

tom of mast jacket (fig. 15).

b.
Install mast jacket lower cover (fig. 15).

6. Connect steering column harness at connector plug.

Connect back-up lamp/neutral safety switch plug, if

so equipped.

7. Inside vehicle, install seal, protective covers, and

trim cover or boot (fig. 13). On Corvette models the

' covers are installed in the engine compartment side.

8. Connect transmission controls to shift levers at

bottom of column if so equipped.

CHEVROLET

CHEVELLE

CORVETTE
CAMARO

Fig.
16—Steering Coupling Clearance Adjustment

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-10

SECTOR SHAFT SEAL REPLACEMENT

A faulty seal may be replaced without removal of

steering gear from car by removing pitman arm as out-

lined under Maintenance and Adjustments--Steering Gear

Adjustments and proceed as follows:

1.
Loose lash adjuster lock nut and turn lash adjuster

screw several turns counterclockwise.

2.
Remove three cap screws holding side cover to gear

bushing.

3.
Pull side cover and sector shaft from gear housing

as a unit. Do not separate side cover from sector

shaft.

4.
Pull sector shaft seal from gear housing using

hooked tool or pliers.

5. Coat new seal with chassis grease and position in

sector shaft bore.

6. Place a socket or piece of pipe of suitable diameter

on top of seal and drive seal into bore by tapping

pipe or socket with soft hammer.

7. Install sector shaft side cover assembly, being care-

ful not to damage new seal with splines on end of

shaft; splines may be wrapped with a few turns of

tape to prevent this.

8. Install new side cover gasket and align side cover on

gear housing and install cap screw.

9. Perform steering gear adjustment and install pitman

arm as outlined under Maintenance and Adjustments.

STEERING COLUMN

All models are equipped with new energy absorbing

steering columns. The columns are of five basic designs

as follows:

1.
Syncromesh. The syncromesh column is used on

models with standard, column mounted, conventional

shift levers. The shift tube, within the outer mast

jacket, includes two lower shift levers for connection

to the transmission control linkage.

2.
Automatic and floor shift. This column is used on

models equipped with column mounted powerglide

shift levers, or models with floor shift. If the ve-

hicle has the column mounted powerglide shift con-

trol, the inner shift tube has a single lower shift

lever for connection to the transmission control

linkage. On floor shift models, no lower shift levers

are present on the shift tube.

3.
Tilt wheel option. The upper end and steering shaft

of this column is specially designed to accommodate

the optional tilt steering wheel.

4.
Standard Corvette Column. The standard Corvette

column is similar in design to the Automatic and

Floor Shift column used on other models, except

no shift tube is used. Other differences are pointed

out in the disassembly and assembly procedures for

Standard Corvette column.

5. Telescopic wheel option. The upper end and steering

shaft of this column is specially designed to ac-

commodate the optional telescoping steering wheel.

To perform service procedures on steering column

upper end components, it is not necessary to remove the

column from the vehicle. The steering wheel, horn com-

ponents, turn signal switch, upper housing with bearing,

shift control lever, hazard warning knob, and upper shift

bowl may all be removed with the column remaining in

the vehicle. When servicing the above components, omit

the removal procedure and proceed with the applicable
disassembly procedures. Because of the numerous dif-

ferences in steering column types, be sure to refer to the

set of instructions below which apply to the exact column

to be serviced:

CAUTION: The outer mast jacket, shift tube, _

steering shaft, and instrument panel column

mounting b
racket

are designed as energy ab-

sorbing units. Because of the design of these

components, it is absolutely necessary to handle

the column with care when performing any serv-

ice operation required. Avoid hammering, jar-

ring, dropping, or leaning on any portion of the

column.

Removal

1.
Disconnect steering column harness at connector.

Disconnect neutral safety switch and back-up lamp

switch connectors if so equipped.

Remove steering wheel as outlined in this section.

Remove nuts and washers securing flanged end of

column to steering gear. On Chevy H models, re-

move nut and clamp bolt securing lower end of steer-

ing column to steering gear.

Disconnect transmission control linkage, if so

equipped, from lower column shift tube, levers.

Chevrolet and Chevy II only: Remove screws at-

taching upper and lower mast jacket covers together.

On Chevrolet, remove screws attaching lower cover

to instrument panel (figs. 15 and 18). Remove lower

cover.

Chevelle only: Remove screws securing mast jacket

trim cover to instrument panel and remove cover

(fig. 15).

Corvette, only: Remove screws securing escutcheon

to instrument panel. Remove screws securing upper

and lower covers together and remove covers.

On Chevrolet and Chevelle columns with Powerglide

shift levers, loosen set screw at six o'clock position

at bottom of column and remove the transmission

shift indicator pointer (fig. 15).

9. Chevrolet only (fig. 19):

a. Remove screws securing cover trim to dash

panel and remove cover trim.
2.

3.

4.

5.

6.

7.

8.

Fig.
18—Mast Jacket Cover Attachments—Chevy II

CHEVROLET CHASSIS SERVICE MANUAL

STEERING
9-13

Fig.
25—Removing
Wiring
Protector

will damage the column. If support fixture

J- 22573 is not used, frequently check position

of column in vise jaws to insure column is not

working free of jaws.

2.
Clamp column in a bench vise as shown in Figure

26.

3.
Slide upper bearing preload spring and cancelling

cam off end of shaft (fig. 26).

4.
Remove turn signal lever retaining screw and re-

J

/
P TT-T. ,,.. "~~ ••• -£;:«s-tu

4
• h ^•--
:z:--:vmM
UPPER
BEARING
PRELOAD
SPRING

Fig.
27—Upper
Bearing
Preload
Spring
and
Cancelling
Cam

move lever. Push hazard warning switch in, unscrew

and remove knob.

5. Drive out shift control lever retaining pin and re-

move shift lever.

6. Remove "C" retaining ring from upper steering

shaft using snap ring remover Tool J-22569 as shown

in Figure 28.

7. Slide thrust washer and wave washer off upper steer-

ing shaft (Fig. 28).

8. Loosen three turn signal switch mounting screws

until the switch cover can be rotated counterclock-

wise. It may be necessary to push on top of screws

to loosen the cover assembly.

NOTE:
Do not remove the three turn signal

switch screws completely unless it is necessary

Fig.
26—Column
Secured
in
Bench Vice
Fig.
28—Removing
or
Installing
"C"
Ring
Retainer

Using Tool
J-22569

CHEVROLET CHASSIS 3ERV1CI MANUAL

STEERING 9-14

Fig.
29—Removing Turn Signal Switch Cover from Column

to replace the turn signal switch, lockplate, or

upper bearing housing and bearing.

9. Rotate turn signal switch cover counterclockwise and

pull cover off top of jacket (Fig. 29).

10.
Remove shift lever bowl from top of jacket.

11.
If necessary, pry upper shift lever spring (fig. 30)

from bowl and discard spring. Remove bowl washer

(fig. 30).

12.
If necessary to service components within the signal

switch cover, remove the three signal switch mount-

ing screws completely from engagement with the

lockplate. Use care to control three springs as

screws are removed. -

13.
Remove turn signal switch and upper bearing housing

assembly from cover.

H

SHIFT
r

i

LEVER
a

SPRING
I^-BOWL

Sk WASHER
14.
Carefully pull steering shaft assembly from bottom

of column.

15.
Remove nuts securing back-up lamp switch to col-

umn and remove switch. Retain these mounting nuts.

16.
Remove three bolts securing reinforcing ring to

adapter just above the lower gearshift levers. It is

very important to retain these bolts for reassembly.

Use of the wrong size bolts during reassembly would

result in damage to the column.

17.
Remove reinforcing ring, adapter with bearing, first

and reverse shift lever, and spacer from lower end.

18.
Withdraw shift tube assembly from lower end.

19.
Remove the lower bowl bearing from the top end of

the jacket by inserting a suitable length of pipe or

wooden rod through the lower end and tapping the

- bearing out. This bearing may be reused in this col-

umn or discarded. It may not be used as a replace-

ment part in another column.

20.
If necessary, remove and discard lower bearing.

21.
If necessary, unwrap mesh cover from jacket.

Assembly—Syncromesh Column (Fig. 24)

1.
Apply a thin coating of lithium soap grease to all

friction surfaces.

2.
If lower bearing was removed, press a new lower

bearing into the adapter.

3.
If lower shift bowl bearing was removed from jacket,

press bowl bearing into top end of jacket.

4.
Insert the shift tube assembly into the lower end of

the jacket.

NOTE: Be sure friction surfaces of lower

levers and mating bearing surfaces are greased

before performing the next step.

5.
Assemble the lever spacer, first and reverse lever,

adapter with bearing, and reinforcing ring. Place

this assembly into position on the lower end of the

SHIM (ONE

ON EACH SIDE)

Fig.
30—Upper Shift Lever Spring and Bowl Washer
Fig.
31—Bottoming Shift Levers Using Spanner Wrench J-22568

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-15

jacket and loosely secure using the three bolts re- 8.

moved during disassembly.

Place a 0.005 maximum shim on each side of the 9.

shaft, between either one of the shift levers and the

spacer (fig. 31). 10.

Using spanner wrench J-22568 installed in spanner

holes in adapter, rotate the.adapter clockwise until

the shift levers are bottomed out (fig. 31). Bottom

the adapter against the jacket while rotating to re-

move end play. 11.
Tighten the three adapter bolts. Remove the two

0.005 shims.

Insert the steering shaft assembly into position

through the lower end of the jacket.

Attach the back-up lamp switch loosely to the jacket

using the same nuts removed during disassembly.

Install these nuts loosely, switch will be tightened to

the jacket when column is installed in vehicle and

shift levers are aligned.

If upper shift lever spring was removed, press a

10 9 8
6 5 4 3 2 1

Fig.
32—Column Mounted Powerglide Lever or Floor Shift Column—Exploded View

1.
Steering Wheel

Nut

2.
Screw

3. Retaining Ring

4.
Thrust Washer

5. Wave Washer
6. Turn Signal Switch

7. Upper Bearing Assembly

8. Cover

9. Spring

10.
Lock Plate

11.
Shift Lever Spring
12.
Bowl

13.
Bearing

14.
Mast Jacket

15.
Wiring Protector

16.
Shift Tube

17.
Washer
18.
Spring

19.
Bearing

20.
Retainer

21.
Steering Shaft

22.
Tolerance Ring

Kit

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-16

new upper shift lever spring into bowl pocket. Be

sure spring is seated in bowl pocket. Install bowl

washer (fig. 30).

12.
Insert the upper bearing housing assembly and the

turn signal switch assembly into the cover, feeding

the signal switch wires through the back of the

cover.

13.
Align the signal switch and bearing housing holes

with the holes in the cover. Install three mounting

screws through the holes.

14.
Slide three springs onto screw ends at rear of cover

and place lockplate in position over screws and

springs. Turn screws three turns into lockplate.

15.
Feed switch wire through the shift lever bowl and

place upper end assembly on top of bowl.

16.
Place the shift lever bowl and signal switch cover

assembly on top of jacket, aligning the tangs on the

I.D. of the lockplate with the slots in the top of the

jacket. Shift tube key should align in bowl keyway as

bowl is pushed ono

17.
Lock upper end assembly into position by pushing

down on the cover assembly and rotating assembly

fully clockwise. Tangs of lock plate must engage

slots in jacket.

18.
Tighten three turn signal switch mounting screws in

a gradual criss-cross sequence to avoid cocking the

lockplate.

19.
Slide wave washer and thrust washer over steering

shaft and against upper bearing housing.

20.
Start "C" retaining ring over steering shaft taper.

Complete installation of. retaining ring using snap

ring installer J-22659 as shown in Figure 28. Be

sure "C" retaining ring is completely seated into

steering shaft groove.

21.
-Place turn signal switch lever in position and secure

with screw. Screw hazard warning knob into position.

22.
Remove column from vise and pull wires flat against

jacket. Snap wire protector into place.

23.
If mesh cover was removed, wrap mesh cover around

jacket and secure with electricians or friction tape.

24.
Slide cancelling cam and upper bearing preload

spring onto end of shaft.

Disassembly—Column Mounted Power glide Lever or

Floor Shift Column (Fig. 32)

NOTE: In this procedure, automatic refers to a

column with a column mounted, Powerglide shift-

ing lever. Floor shift refers to a column taken

from a vehicle with conventional or Powerglide

floor shift controls.

1.
Unsnap and remove wiring protector and wiring clip.

CAUTION: Secure column in bench vise for

service one of two ways shown in Figure 26.

Clamping column in vise in any other manner

will damage the column. If support fixture

J^22573 is not used, frequently check position of

column in vise jaws to insure column is not

working free of jaws.

2.
Clamp column in a bench vise as shown in Figure 26.

3.
Slide upper bearing preload spring and cancelling

cam off end of shaft.

4.
On automatic columns removed from Chevy II or

Camaro, remove screws securing dial retainer to

column and remove retainer and dial (fig. 33). Slide
Fig.
33—Powerglide Dial Indicator Assembly—Chevy II

and Camaro

indicator out of shift bowl and remove indicator. Re-

move cap and bulb from turn signal switch housing.

5.
Remove turn signal lever retaining screw and re-

move lever. Push hazard warning knob in; unscrew

and remove knob.

6. On automatic columns, drive'out shift control lever

retaining pin and remove shift lever.

7.
Remove "C" retaining ring from upper steering

shaft using snap ring remover Tool J-22569 (fig. 28).

8. Slide thrust washer and wave washer off upper steer-

ing shaft (fig. 28).

9. Loosen three turn signal switch mounting screws

until the switch cover can be rotated counterclock-

wise.
It may be necessary to push on top of screws

to loosen the cover assembly. ,

NOTE: Do not remove the three turn signal

switch screws completely unless it is necessary

to replace the turn signal switch, lockplate, or

upper bearing housing and bearing.

10.
Rotate turn signal switch cover counterclockwise

and pull cover off top of jacket (fig. 29).

11.
If necessary, pry upper shift lever spring (fig. 30)

from bowl and discard spring.

12.
Remove shift lever bowl from top of jacket.

13.
If necessary to service components within the signal

switch cover, remove the three signal switch covers,

remove the three signal switch mounting screws

completely from engagement with the lockplate. Use

care to control three springs as screws are removed.

14.
Remove turn signal switch and upper bearing housing

assembly from cover.

15.
Carefully pull steering shaft assembly from bottom

of column.

16.
Remove securing back-up lamp/neutral start switch

to column, if so equipped, and remove switch. Retain

these mounting nuts.

CHEVROLET CHASSIS SERVICE MANUAL