ignition CHEVROLET CAMARO 1967 1.G Chassis Service Manual

CLUTCH AND TRANSMISSIONS 7-32

21.
Remove transmission output shaft slip yoke and in-

sert a plastic shipping plug in end of extension to

prevent spillage of transmission fluid.

NOTE:
The yoke is removed to avoid tearing

the heat reflecting pad on the underbbdy, when

the transmission is being removed.

22.
Remove bright metal ignition shielding from dis-

tributor area.

23.
Remove the transmission dip stick and tube

assembly.

24.
Disconnect transmission vacuum modulator line at

distributor advance line tee.

25.
Position transmission hoist under transmission and

attach safety chain to transmission.

26.
Remove transmission converter housing-to-engine

attaching foolts and slide transmission rearward.
NOTE:
Observe converter when moving trans-

mission rearward. If converter does not move

with the transmission, pry it free of flywheel

before proceeding.

27.
Install converter retaining strap.

28.
Lower and remove transmission from vehicle by

tilting the front down and to the right while inter-

mittently lowering the transmission to facilitate its

• removal.

29.
Reinstall transmission assembly by performing the

above steps in reverse order.

Bolt Torques

Transmission Case to Flywheel

Housing Bolts 35 ft. lbs.

Converter to Flywheel Bolts. . , . . 35 ft. lbs.

OTHER SERVICE OPERATIONS

Although certain operations, such as oil pan or gasket

replacement, valve body, governor, filler pipe "O" ring,

speedometer drive gear, case extension "0" ring and

rear oil seal, vacuum modulator, and servo cover or

gasket service may be performed from underneath the
vehicle without removing the Powerglide; their service

procedure is covered in the Passenger Overhaul Manual

and is not repeated here. Refer to the- Powerglide Sec-

tion of the Passenger Overhaul Manual for all other

service operations not covered here.

DIAGNOSIS

Proper operation of the Powerglide transmission may

be affected by a number of factors, all of which must be

considered when trouble in the unit is diagnosed.

Proper trouble diagnosis can only be accomplished

when performed in a thorough step by step procedure.

The following procedure has been devised and tested and

is recommended for all trouble diagnosis complaints and

if the service man will follow this checking procedure,

accurate and dependable diagnosis may be accomplished.

This will result in a savings of time, not only to the

service man, but to the customer as well.

WARMING UP TRANSMISSION

Before attempting to check and/or correct any com-

plaints on the Powerglide transmission it is absolutely

essential that the oil level be checked and corrected if

necessary. An oil level which is either too high or too

low can be the cause of a number of abnormal conditions

from excessive noise to slippage in all ranges.

It must be remembered that cold oil will slow up the

action of the hydraulic controls in the transmission. For

this reason a trouble or oil leak diagnosis should not be

attempted until the transmission has been warmed up by

either of the following procedures:

Shop Warm Up

1.
Connect tachometer to engine.

2.
Set parking brake tight and start engine.

3.
Place selector light in
"D"
(drive) range.

4.
Adjust carburetor idle speed adjusting screw to run

engine at approximately 750 rpm and operate in this

manner for two minutes. At the end of two minutes

of operation, the transmission will be sufficiently

warmed up for diagnosis purposes.
NOTE:
At this point, readjust the engine idle

speed to 450-475 rpm in
"D"
range.

Road Warm Up

Drive the car approximately 5 miles with frequent

starts and stops.

NOTE:
At this point, make sure the engine idle

speed is set to 450-475 rpm in
"D"
range.

CHECKING FLUID LEVEL AND CONDITION

After transmission has been warmed up, check the

fluid level with the engine idling, parking brake set and

control lever in "N" (neutral). If the fluid level is low,

add fluid to bring level up to the full mark on gauge rod,

CAUTION: If fluid level is too high, fluid may

be aerated by the planet carrier. Aerated fluid

will cause turbulence in the converter which will

result in lost power, lower stall speed and lower

pressures in control circuits. Lower fluid level

to full mark, then shut off engine to allow air

bubbles to work out of fluid.

When checking oil level, aburned smell and discolora-

tion indicate burned clutches or bands and the transmis-

sion will have to be removed.

MANUAL LINKAGE

Manual linkage adjustment and the associated neutral

safety switch are important from a safety standpoint.

The neutral safety switch should be adjusted so that the

engine will start in the Park and Neutral positions only.

With the selector lever in the Park position, the park-

ing pawl should freely engage and prevent the vehicle

CHEVROLET CHASSIS SERVICE MANUAL

SECTION 12

ELECTRICAL-BODY AND CHASSIS

CONTENTS
OF
THIS
SECTION

Page
Page

System 12-1

Instruments and Gauges 12-21

Directional Signal 12r40
Windshield Wipers and Washers 12-44

Wiring Diagrams 12-56

Special Tools 12-60

LIGHTING SYSTEM

INDEX

Page

General Description
!2-i

Maintenance and Adjustments
•.................. 12-2

Headlamp Adjustment......................
12-3

Headlamp Panel Travel Adjustment.
12-5

Service Operations.
. . .. 12-5

Front Lighting
12-5

Headlamp
. 12_5

Parking Lamp
12-5

Fender Lamp
. 12_^

Headlamp Panel
12-8

Headlamp Panel Motor
^2-9

Rear Lighting
l2-10

Tail, Stop and Directional Lamps
12-10
Page

Backing Lamps
12-14

License Plate Lamp
12-14

Automatic Transmission Quadrant Lamp
12-14

Seat Separator Console Lamps
. 12-15

Lighting Switch
. . 12-15

Wiper Switch.
12-15

Stoplight Switch
12-15

Dimmer Switch
12-15

Backing Lamp Switches
12-15

Neutral Safety Switches
12-17

Parking Brake Alarm Switch
................. 12-19

Instrument Panel Compartment Lamp/Switch
12-19

Cirgarette Lighter
12-19

GENERAL DESCRIPTION

.
The lighting system includes: the main lighting switch,

stop light, dimmer, and backing lamp switches, head-

lamps, parking lamps, stop, tail and directional lamps,

instrument illumination and indicator lamps, and the

necessary wiring to complete the various circuits. A

fuse panel provides convenient power take offs and fuse

clips for the appropriate circuits (fig. 1).

Chevrolet and Chevelle headlamp installation is all

new in that the headlamps are located in the radiator

support with adjusting screws and springs. Eliminating

the need for having separate headlamp housings. Chev-

rolet and Chevelle headlamp retainers and springs are

interchangeable.

Chevy n headlamp housings are new because of revised

front end styling and Corvette front end lighting is basi-

cally carryover.

Front fender lamps have been added as an option for

Chevrolet models and as standard equipment on Caprice

series.

Camaro models use single headlamps and the Rally

Sport model headlamps are covered by a retractable

section of the grille when lamps are not used. The sec-

tion of the grille covering the headlamps folds back when

lights are required; the headlamps are stationary. The

covering is retracted by a small electric motor mounted

to the headlamp housing. The headlamps are automat-

ically uncovered when the headlight switch is pulled "ON"

for illumination. If at any time the electrical circuit

becomes inoperative, the lamps can be uncovered manu-

ally. The ignition switch must be
"ON"
in order to close

the headlamp doors.

Parking lamp for Chevelle and Chevrolet models are
new due to revised front end sheet metal and bumper

styling. Parking lamps are located in the bumper on

Chevrolet, Chevelle and Chevy n models

Camaro parking lamps are located in the radiator

grille except for the Rally Sport models on which the

parking lamps are in the valance panel. For styling

reasons, the lens is white and an amber glass bulb is

used. All Camaro parking lamps require a separate

ground wire to assure a good ground contact because of

the plastic grille and painted contact surfaces.

The Chevrolet tail, stop, and directional lamps are in

one housing with a three section lens design on Impala

and Caprice sedans. The center lens for Impala series

is the back-up lamp. The center lens on the Caprice is

a tail lamp with the back-up lamps being located in the

rear bumper. Chevrolet station wagons have three indi-

vidual housings with three lenses, the center lamp being

the back-up. Biscayne and Bel-Air sedans have a single

housing and lens for tail, stop, and directional lamp with

a similarly constructed back-up lamp inboard and adja-

cent to it.

Chevelle tail, stop, and directional lamps are a single

lens design that follows through with the rear fender

styling. The back-up lamp is located in r.ear bumper.

Camaro models except Rally Sport have tail lamps

with integral back-up lamps mounted inboard of the rear

fenders between the trunk opening and bumper. The

Rally Sport model has dual tail lamps in the rear housing

and valance mounted back-up lamps.

Corvette, Chevy n, and Corvair tail and directional

signal lights are carryover. The Corvette has new back-

up lamps center mounted above the license plate opening.

CHEVROLET CHASSIS SERVICE

ELECTRICAL-BODY AND CHASSIS 12-2

FJg.
1 - Fuse Panel Assembly

All power window and tailgate circuits require the igni-

tion switch to be "ON" to open or close the windows un-

like past model designs which were operated independ-

ently of the ignition switch.

The windshield wiper and washer switch is new in that

washer button in the center of the knob has been deleted
and its function will be accomplished by pushing the knob.

A set screw is used to retain the knob to the shaft.

In addition to fuses, the wiring harness incorporates

fusible links to protect the wiring. Links are used rather

than a fuse in wiring circuits that are not normally fused,

such as the ignition circuit. Fusible links in the Chevro-

let wiring are four gauge sizes smaller than the cable it

is designed to protect. The links are marked on the

insulation with wire gauge size because of the heavy insu-

lation which makes the link appear a heavier gauge than it

actually is.

Engine compartment wiring harness incorporate sev-

eral fusible links. Each link is identified with its gauge

size.
A fusible link is a length of special wire (normally

four wire gauges smaller than the circuit it is protecting)

used in wiring circuits that are not normally fused, such

as the ignition circuit. The same size wire with a spe-

cial hypalon insulation must be used when replacing a

fusible link.

The links are:

1.
The pigtail lead at the battery positive cable (except

Corvette) is a 14 gauge, brown fusible link protecting

the 10 gange battery charging circuit. This wire is

an integral part of the battery cable assembly and

servicing requires replacing the complete battery

cable assembly. On Corvette models this link is

installed as a molded splice at the solenoid "Bat"

terminal and servicing requires splicing in a new

link.

2.
A 16 gauge black fusible link is located at horn relay

to protect all unfused wiring of 12 gauge or larger.

It is a serviceable piece with an in-line connector

and is not integral with the wiring harness.

3.
The generator warning light and field circuitry (16

gauge wire) is protected by a fusible link (20 gauge

orange wire) used in the "battery feed to voltage

regulator #3 terminal" wire. The link is installed

as a molded splice in the generator and forward lamp

harness and is serviced by splicing in a new 20 gauge

wire as required.

4.
The ammeter circuit on all models is protected by

two orange, 20 gauge wire fusible links installed as

molded splices in the circuit at the junction block or

the solenoid "Bat" terminal (Corvette only) and at the

horn relay. Each link is serviced by splicing in a

new 20 gauge wire as required.

The wiring harnesses use a standarized. color code

common to all Chevrolet vehicles. Under the color code,

the color of the wire designates a particular circuit. The

harness title indicates the type of harness, single of mul-

tiple wire, and also describe the location of the harness.

The body harness is a flat, solid wire assembly and is

routed through the vehicle near the center of the body.

Composite wiring diagrams (figs. 104 thru 124) are in-

cluded at the end of this section.

MAINTENANCE AND ADJUSTMENTS

Maintenance of the lighting units and wiring system

consists of an occasional check to see that all wiring

connections are tight and clean, that the lighting units are

tightly mounted to provide good ground and that the head-

lamps are properly adjusted. Loose or corroded con-

nections may cause a discharged battery, difficult start-

ing, dim lights, and possible damage to generator and

regulator. Wire harnesses must be replaced if insulation

becomes burned, cracked, or deteriorated. Whenever it
is necessary to splice a wire or repair one that is bro-

ken, always use solder to bond the splice. Always use

rosin flux solder on electrical connections. Use insulat-

ing tape to cover all splices or bare wires.

When replacing wires, it is important that the correct

size be used. Never replace a wire with one of a smaller

size.

Each harness and wire must be held securely in place

by clips or other holding devices to prevent chafing or

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-21

2.
Remove ash tray, retainer attaching screws and

retainer.

3.
Remove Air Conditioning distributor
duct'
retaining

screws and duct.

4.
Remove heater and/or Air Conditioning control panel

assembly retaining screws and push panel assembly

from console.

NOTE:
If interference between control panel

and radio is encountered, loosen radio retaining

nuts.

5. Remove radio control knobs, bezels and retaining

nuts.

6. Disconnect radio wiring harness and antenna lead-in.

7. Remove radio rear brace attaching screw and re-

move ra(Jio from vehicle.

8. Remove ignition switch bezel nut using Tool J-7607

and push switch rearward.

9. Disconnect cigarette wiring connector.

10.
Remove cigarette lighter retainer and lighter as-

sembly from console.

11.
To install, reverse removal procedure.
Fig.
35 - Cigarette Lighter — Chevelle

CHEVROLET INSTRUMENTS AND GAUGES

INDEX

Page

General Description 12-21

Service Operations 12-22

Instrument Cluster........................ 12-22

Instrument Cluster Lamps 12-22

Printed Circuit .
* •
12-22

Speedometer 12-22

Speedometer Cable 12-23

Fuel Gauge 12-23
Page

Clock 12-24

Tachometer 12-24

Ammeter . . 12-24

Temperature Gauge 12-24

Oil Pressure Gauge 12-24

Oil Pressure Indicator 12-24

Generator Indicator 12-26

Temperature Indicator 12-26

GENERAL DESCRIPTION

The standard instrument cluster on all models contains

seven circular housings consisting of: a speedometer;

fuel gauge; oil pressure, generator and temperature indi-

cators; right and left directional signal indicators; brake

warning and high beam indicators; and includes a clock

on deluxe models. An optionally available instrument

cluster provides special instrumentation which includes

in addition to the speedometer and clock: a tachometer;

fuel, oil pressure, ammeter and engine temperature

gauges; which replace the standard fuel gauge and indi-

cator lights. The brake warning indicator is relocated

to the tachometer dial face and the high beam and direc-

tional indicators are positioned in the speedometer dial

face.

Instrument cluster removal is recommended before at-

tempting to service the printed circuit and gauges even

though some units may be accessible from behind the

cluster. Limited working space under the instrument

panel increases the possibility of electrical malfunctions

due to poor connections, and damaged or improperly in-

stalled printed circuit. The printed circuit is service-

able but not repairable and requires complete
replacement.

The brake warning light serves a dual purpose. It

functions as an indicator when the parking brake is ap-

plied and also warns if a malfunction (loss of hydraulic

pressure) should occur in the brake system. The two

separate switches, which provide the signal to operate the

indicator, are located at the parking brake support and in

the hydraulic brake line at the master cylinder. Service

of the brake pressure, differential switch unit at the

master cylinder is described in Section 5 of this manual.

All indicator and cluster illumihating lamps may be

replaced without removing the cluster from the vehicle.

The bulbs are installed in plastic holders which lock into

the cluster housing and make contact with the printed

circuit. An instrument lamp is used to illuminate the

ignition switch. A special fibre optic lucite wiring

transmits light from the lamp to the switch.

Regular maintenance is not required on the instrument

cluster or its components other than maintaining clean,

tight electrical connections, replacing defective parts and

keeping the speedometer cable properly lubricated.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-23

IGNITION SWITCH LIGHTING

VIEW A

1.
Clock Knob Assembly

2.
Instrument Cluster Lamps

3. R.H. Directional Indicator

4.
"Gen'*
Indicator

5. Fuel Gauge
Fig.
38 - Instrument Cluster Connections

6. L.H. Directional

Indicator

7. "Hot" indicator

8. "Brake" Indicator

9. "Bright" Indicator
10.
"Oil Press" Indicator

11.
Clock Cover (jl5,0OQ)

12.
Clock Assembly (16,000)

1.3; Printed Circuit

14.
Instrument Panel Connector

3.
Remove screws retaining speedometer to the housing

and remove speedometer from rear cover.

NOTE:
Servicing of the speedometer assembly

should be performed by an authorized
AC
Speed-

ometer Service Station.

4.
To install, reverse the removal procedure.

SPEEDOMETER CABLE

Replacement or Lubrication

1.
Disconnect the speedometer cable from the speedom-

eter head. Remove the old cable by pulling it out

from speedometer end of conduit.

NOTE:
If old cable is broken it may be neces-

sary to remove lower piece from transmission

end of conduit.
2.
Lubricate the lower 3/4 of cable with speedometer

cable lubricant and push the cable into the conduit.

Connect the upper end to the speedometer head and

road test vehicle for proper speedometer operation.

FUEL GAUGE REPLACEMENT

1.
Remove instrument cluster as previously described

in this section.

2.
Remove cluster lamps from gauge cover plate and

remove terminal nuts attaching circuit to gauge.

3.
Carefully move printed circuit away from gauge and

remove screws retaining gauge assembly to the

cluster housing.

4.
Remove gauge assembly from cluster housing and

remove three terminal nuts attaching gauge to the

cover plate.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-24

1.
Temperature Gauge

2.
Instrument Cluster Lamp

3.
R.H. Directional Indicator

4.
Ammeter Gauge
Fig. 39- Optional Gauge Cluster

5. Fuel Gauge

6. L.H. Directional Indicator

7. Tachometer

8. "Brake" Indicator

9. "Bright" Indicator
10.
Oil Pressure Fitting

11.
Chassis Harness Connector

12.
Clock Assembly

13.
Printed Circuit

NOTE:
Observe carefully the stack up of the

internal parts of the fuel gauge assembly.

5. To install, reverse removal procedure.

CLOCK OR TACHOMETER REPLACEMENT

NOTE:
The tachometer is a self-contained, all

transistor unit requiring very little service

other than keeping the terminal nuts clean and

tight. The unit is not serviceable and must be

replaced, if defective.

1.
Remove instrument cluster as previously described

in this section.

2.
For clock replacement, remove clock set shaft knob

at front of console.

3.
Remove cluster lamps from cover, circuit attaching

screws, and terminal nuts at circuit to gauge attach-

ing points.

4.
Move printed circuit away from gauge and remove

screws retaining
•_
gauge or clock to the cluster

housing.
•5.
Remove unit, from housing and cover plate from

gauge unit.

6/To install, reverse removal procedure.

AMMETER TEMPERATURE AND OIL PRESSURE

GAUGES REPLACEMENT

1.
Remove instrument cluster as previously described

iii this section.

2.
Remove instrument lamps, attaching screws or nuts

and wiring connections as required.

3.
Remove gauge assembly backing plate retaining

screws and remove gauge assembly from cluster

housing.

4.
Remove terminal nuts and/or screws retaining gauge

to the backing plate and separate plate from the

gauge.
•

5. To install, reverse removal procedure.

OIL PRESSURE INDICATOR

If the light does not come on when the ignition switch is

turned on, or if the light comes on and remains on after

the engine is started, one or more of the following condi-

tions is indicated:

CHEVROLET CHASSIS SERVICE MANUAL

10

27

18

1.
To R. H. Door Jamb Switch

2.
To Inst. Pane! Compt. Light

3. To Heater Control

4. Heater Control Lamp

5. To Ignition Switch

6. To Seat Separator Harness Conn.

7. Inst. Cluster Conn.

8. To Directional Signal Conn.

9.
Door Jamb Switch to Light Switch Conn,
Fig.
40 - Instrument Panel Wiring

10.
To Wiper Switch

11.
To Light Switch Conn.

12.
To Gen. and Fwd. LP. Harness Asm,

13.
To Light Switch

14.
Courtesy Lamp

15.
To Dome Lamp Conn.

16.
ToL.H. Door Jam Switch

17.
Gen. and Fwd Harness Conn.

18.
To Paricing Brake Alarm Switch
19.
To Rear Door Jamb Switch

20.
To Fisher Body Conn.

21.
To Stop Lamp Switch

22.
To Back-Up Lamp Switch

23.
To Directional Signal Flasher

24.
To Cigarette Lighter

25.
To Heater Resistor

26.
Directional Signal Flasher

27.
Door Jamb Switch

ELECTRICAL-BODY
AND
CHASSIS
12-26

•
Low oil
pressure

• High engine temperature

• Defective wiring
or
switch

connector from sender

in block above starter
on

and
at
left front
of
distributor
on V-8
Sending Unit Replacement

1.
Disconnect wiring harness

unit terminal (located

L-6 engines

engines).

2.
Remove sender unit using Tool J-21757
or 12
point

socket, replace with
new
unit
and
check operation.

GENERATOR INDICATOR

1.
Ignition
on,
Engine
not
Running
and
Telltale Light

Off.

• Indicator bulb burned out, replace bulb.

• Open circuit
or
loose connection
in the
telltale

light circuit.

2.
telltale Light Stays
on
after Engine
is
Started.
If indicator light does
not go out at
engine idle

speed, refer
to
Charging Systems under Engine

Electrical, Section
6Y.

TEMPERATURE (COOLING SYSTEM) INDICATOR

The temperature indicator circuit consists
of two re-

motely located units, indicator gauge
and
engine sender

unit.
The
indicator gauge, located
in the
instrument

panel, consists
of a
red light which will indicate
an
over-

heated engine condition.

Engine Sender Unit Replacement

1.
Drain engine cooling system
to a
level below unit.

2.
Remove sender unit (located
in the
inlet manifold

near water pump housing
on V-8
engines and
in the

cylinder head near
an
exhaust port
oh L-6
engines)

and replace with new unit.

3.
Refill cooling system
and
check operation
of
unit.

CHEVELLE INSTRUMENTS AND GAUGES

INDEX

Page

General Description
* *
i2-26

Service Operations
12-26

Instrument Panel
12-26

Instrument Cluster.
12-26

Fuel Gauge and/or Ammeter
12-27

Clock,
i 12-27

Speedometer
12-27
Page

Speedometer Cable
.
. 12-27

Temperature Gauge
12-29

Oil Pressure Gauge
12-29

Indicator Lights.
. 12-29

Oil Pressure Indicator
12-29

Generator Indicator
. . 12-29

• Temperature Indicator
12-29

GENERAL DESCRIPTION

The Chevelle instrument cluster assembly consists
of:

a speedometer;
a
fuel gauge;
a
generator,
an
engine
tem-

perature and an
oil
pressure indicator lamp, and includes

a clock
on
deluxe models.
On
super sport models,
am-

meter, coolant temperature
and oil
pressure gauges
re-

place
the
appropriate indicator lights. Except
for the

speedometer,
all of the
indicator lamps, instruments
and

gauges
of
these clusters may
be
serviced without remov-

ing
the
instrument cluster assembly from
the
vehicle.

In addition
to the
instrument indicator lamps,
a
brake

warning lamp
is
included
in the
cluster
as
standard

equipment.
The
indicator
is
connected
to the
parking
brake
and
brake pressure differential switches
and

serves
a
dual function.
It
lights when the parking brake

is applied
and
also when
the
brake pedal
is
applied,
if a

malfunction should occur
in the
brake system
due to a

loss
of
hydraulic pressure. Servicing
of the
hydraulic

pressure differential switch
is
covered
in
Section
5 of

this manual.

Regular maintenance
is not
required on the instrument

cjLuster
or its
components other than maintaining dean

and tight electrical connections, replacing defective parts

and keeping
the
speedometer cable properly lubricated.

SERVICE OPERATIONS

INSTRUMENT PANEL ASSEMBLY

INSTRUMENT CLUSTER (Figs.
41
thru
44)

Removal

1.
Disconnect battery ground cable.

2.
Remove steering coupling bolt and disconnect steer-

ing shaft from coupling.

3.
Loosen mast jacket lower clamp.

4.
Remove
air
conditioning center distributor duct
(if

so equipped).

5. Remove radio rear support bracket screw.

6. Remove mast jacket upper support clamp and retain-

ing bolts from lower support (refer
to
Section
9,

Steering).
CAUTION: Cover mast jacket
and
parl

brake handle with
a
suitable material
to
prevc

scratching.

7.
Disconnect speedometer cable
at
rear
of
cluster

housing
and
speed warning control knob
at
panel
(if

so equipped).

8. Remove instrument panel retaining screws (nine

upper and five lower).
.

9. Working under the console remove four lower retain-

ing screws from instrument cluster housing.

10.
Pull instrument panel assembly from console and
lay

forward on mast jacket.

11.
Disconnect wiring harness, cluster lamps and wiring

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-29

Fig.
43b - Speed Warning Device

TEMPERATURE AND/OR OIL PRESSURE

GAUGE

1.
Disconnect battery ground cable.

2.
Remove ash tray and ash tray retainer.

3.
Disconnect A/C hose from the distributor duct.

4.
Disconnect wiring connectors and lamp bulbs from

rear of gauge.

5. Disconnect oil pressure pipe fitting from rear of oil

pressure gauge.

6. Remove (3) screws retaining gauge assembly to

cluster cover and disengage unit from cover.

7. Remove (4) retaining nuts and remove gauge from

template.

8. To install, reverse removal procedure.

INDICATOR LIGHT REPLACEMENT

To replace any indicator or cluster bulb, unsnap the

proper socket from rear of instrument cluster, remove

and replace bulb, and reinsert unit into rear of cluster

housing.
OIL PRESSURE INDICATOR

If the light does not come on when the ignition switch is

turned on, or if the light comes on and remains on after

the engine is started, one or more the following condi-

tions is indicated:

• Low oil pressure

• Defective wiring or switch

• High engine temperature

Switch Replacement

1.
Disconnect wiring harness connector from sender

unit terminal (located in block above starter on L-6

engines and at left front of distributor on V-8

engines).

2.
Remove sender unit using Tool J-21757, replace with

new unit, and check operation.

GENERATOR INDICATOR

Ignition on, Engine not Running and

Telltale Light Off

1.
Indicator bulb burned out, replace bulb.

2.
Open circuit or loose connection in the telltale light

circuit.

Telltale Light Stays on after Engine is Started

If indicator light does not go out at engine idle speed,

refer to' Charging Systems under Engine Electrical,

Section 6Y.

TEMPERATURE
(COOLING
SYSTEM)
INDICATOR

The temperature indicator circuit, consists of two re-

motely located units, indicator gauge and engine sender

unit. The indicator gauge on all models uses a single

red light to indicate an overheated engine condition.

Engine Sender Unit Replacement

1.
Drain engine cooling system to a level below unit.

2.
Remove sender unit (located in the inlet manifold

near water pump housing on V-8 engines and in the

cylinder head near an exhaust port on L-6 engines)

and replace with new unit.

3.
Refill cooling system and check operation of unit.

CHEVROLET CHASSIS SERVICE MANUAL

VIEW
A

VIEW
B

(13700-800)

Fig. 44
-
Instrument Panel Wiring Harness

1.
R.H. Door Jamb Switch

2.
To Instrument Panel

Compartment Light

3. Heater Control Lamp

4.
Ignition Switch Connector

5. Cigarette Lighter

Connector
6. W/S Wiper Switch

Connector

7. Light Switch Connector

8.
L.H.
Door Jamb Switch

9.
To
Body Harness Connector

10.
Parking Brake Alarm

Switch Connector
11.
Directional Signal Switch

Connector

12.
Backing Lamp Switch

Connector

13.
Stop-Lamp Switch

Connector

14.
Flasher Unit
15.
Heater Control Switch

Connector

16.
Heater Resistor Connector

17.
Console Courtesy Lamp

Connector

18.
Neutral Safety Switch

Connector