wheel torque CHEVROLET CAMARO 1967 1.G Chassis Service Manual

CLUTCH
AND
TRANSMISSIONS
7-23

Assembly (Fig.
4X)

1.
With detent spring tang projecting
up
over
the 3rd

and
4th
shifter shaft cover opening install
the
first

and second detent
cam
onto
the
detent
cam
pivot
pin.

With
the
detent spring tang projecting
up
over
the

first
and
second shifter shaft cover hole install
the

3rd
and 4th
detent
cam,

NOTE:
The 1-2
detent
cam has a
.090" greater

contour
on the
inside detent notch.

2.

3.
Install detent
cam
retaining
"C"
ring
to
pivot shaft,

and hook spring into detent
cam
notches.

Install
1-2 and 3-4
shifter shaft assemblies
in
cover

being careful
not to
damage seals. Install both shift

forks
to
shifter shaft assemblies, lifting
up on
detent
cam
to
allow forks
to
fully seat into position.

4.
Install reverse detent ball
and
spring
to
cover, then

install reverse shifter shaft assembly
to
cover.

5.
Install outer shifter levers, flat washers, lock wash-

ers
and
bolts.

Installation

1.
Shift shifter levers into neutral detent (center) posi-

tion. Position cover gasket
on
case.

2.
Carefully position side cover into place making sure

the shift forks
are
aligned with their respective

mainshaft clutch sliding sleeves.

Install cover attaching bolts
and
tighten evenly
to

specified torque.

Remove filler plug
and add
lubricant specified
in

Section
0, to
level
of
filler plug hole.
3.

4.

ALUMINUM POWERGLIDE

INDEX

Page

General
Description
7-23

Maintenance
and
Adjustments .............. 7—23

Oil
Level Check
7-23

Periodic
Oil
Change
7-24

Periodic
Low
Band Adjustment
7-24

Manual
Shift Linkage Check
and
Adjust
7-24

Floor
Shift Linkage
7-25

Floor
Mounted Control Lever
and

Bracket
Assembly
7-29

Throttle
Valve Linkage
.... 7-29

Neutral
Safety Switch
.. . 7-30

Throttle
Return Check Valve (Dashpot)
7-30

Component
Parts Replacement
7-30

Transmission
Replacement .............. 7—30
Page

Other
Service Operations
7-32

Diagnosis
7-32

Warming
Up
Transmission
7-32

Shop
Warm
Up , 7-32

Road
Warm
Up 7-32

Checking
Fluid Level
and
Condition
7-32

Manual
Linkage
7-32

Oil
Leaks
7-33

Basic
Pressure Checks
7-33

Wide
Open Throttle Upshift Pressure Check
.... 7-33

Idle
Pressure
in
Drive Range
7-33

Manual
"Low"
Range Pressure Check .......
7-33

Drive
Range Overrun (Coast) Pressure
.
.......
7-33

Powerglide
Shift Points
. . 7-35

GENERAL DESCRIPTION

The case
and
converter housing
of the two
speed alumi-

num Powerglide Transmission
is a
single case aluminum

unit. When
the
manual control
is
placed
in the
drive
po-

sition,
the
transmission automatically shifts
to low
gear

for initial vehicle movement.
As the car
gains speed
and

depending
on
load
and
throttle position,
an
automatic shift

is made
to
high gear.
A
forced downshift feature
pro-

vides
a
passing gear
by
returning
the
transmission
to low

range.

The
oil
pump assembly
is a
conventional gear type
and

the
oil
pump housing
is of the
large diameter type acting

as
the
front bulkhead
of the
transmission.
The
torque

converter
is a
conventional three element welded design

bolted
to the
engine flywheel which drives through
a
two-

speed planetary gearset.
The
high clutch assembly
is

typical
of the
designs used
in
this type transmission.
The

aluminum Powerglide uses
an
output shaft mounted
gov-
ernor which requires
a
hole through
the
output shaft.
The

reverse clutch assembly
is a
multiple disc type clutch.

The steel plates
are
splined directly
to the
case while
the

face plates
are
splined
to the
internal
or
ring gear.
The

clutch piston operates within
the
rear portion
of the
case.

The internal diameter
of the
pistoh
is
sealed to
an
integral

hub portion
of the
case rear bulkhead.
The
outside
dia-

meter
is
sealed
to a
machined portion
of the
case.
The

piston
is
hydraulically applied
and is
released
by
separate

coil springs.
The
valve body assembly
is
bolted
to the

bottom
of the
transmission case
and is
accessible
for

service
by
removing
the oil pan
assembly.
The
valve

body consists
of an
upper
and
lower body located
on
either

side
of a
transfer plate.
The
vacuum modulator
is lo-

cated
on the
left rear face
of the
transmission case.
The

modulator valve bore
is
located
in the
upper valve body.

MAINTENANCE
AND
ADJUSTMENTS

OIL LEVEL CHECK

The transmission
oil
level should
be
checked period-

ically
as
recommended
in
Section
0. Oil
should
be
added

only when level
is on or
below
the
"ADD" mark
on the dip

stick with
oil hot or at
operating temperature.
The oil

level
dip
stick
is
located
at the
right rear
of the
engine
compartment. Fill with
oil
specified
in
Section
0.

In order
to
check
oil
level accurately,
the
engine should

be idled with
the
transmission
oil hot and the
control

lever
in
neutral (N) position.

It
is
important that
the oil
level
be
maintained
no

higher than
the
"FULL" mark
on the
transmission
oil

level gauge.
DO NOT
OVERFILL,
for
when
the oil
level

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-24

is at the full mark on the dip stick, it is just slightly be-

low the planetary gear unit. If additional oil is added,

bringing the oil level above the full mark, the planetary

unit will run in the oil, foaming and aerating the oil. This

aerated oil carried through the various oil pressure pas-

sages (low servo, reverse servo, clutch apply, converter,

etc.) may cause malfunction of the transmission assem-

bly, resulting in cavitation noise in the converter and

improper band or clutch application. Overheating may

also occur.

If the transmission is found consistently low on oil, a

thorough inspection should be made to find and correct

all external oil leaks.

PERIODIC OIL CHANGE

The transmission oil should be changed periodically as

recommended in Section 0, and whenever transmission is

to be removed from the vehicle for repairs.

1.
Run engine for one minute in neutral prior to chang-

ing.

2.
Be sure vehicle is level or raise from the rear only.

3.
Remove the oil pan drain plug and allow oil to drain

thoroughly into a pan or can.

Replace drain plug and refill with approximately two

quarts of oil specified in Section 0.

NOTE: To refill the transmission, remove dip

stick from oil filler tube and refill transmission

with oil specified in Section 0 using filler tube

and funnel J-4264. Then, after shifting into all

ranges at idle speed to fill all oil passages, the

engine should be run at 800-1000 rpm with the

transmission in Neutral until the oil warms up,

then add oil as required to raise the fluid level

to the full mark on the dip stick. Refill capacity

is approximately 2 qts.
4.

Fig.
1PG - Adjusting Low Band Using J-21848
PERIODIC LOW BAND ADJUSTMENT (Fig. 1PG)

Low band adjustment should be periodically performed

at 12,000 mile intervals, or sooner, as necessary if op-

erating performance indicates low band slippage.

1.
Raise vehicle and place selector lever in neutral.

2.
Remove protective cap from transmission adjusting

screw.

3.
a. On Corvette Models: Drop left exhaust pipe for

clearance.

b.
On Chevelle Models: To gain clearance between

underbody and transmission, it may be necessary

to remove rear mount bolts from crossmember,

and move transmission slightly toward passenger

side of vehicle. .

4.
Loosen adjusting screw lock nut 1/4 turn and hold in

this position with wrench.

5.
Using Special Tool J-21848 adjust band to 70 in. lbs.

and back off four (4) complete turns for a band which

has been in operation for 6,000 miles or more,.or

three (3) turns for one in use less than 6,000 miles.

CAUTION: Be sure to hold the adjusting screw

lock nut at 1/4 turn loose with a wrench during"

the.adjusting procedure.

6. Tighten the adjusting screw lock nut to specified

torque.

CAUTION: The amount of back-off is not an

approximate figure, it must be exact.

MANUAL SHIFT LINKAGE CHECK & ADJUST

(Column Type)

1.
The shift tube and lever assembly must be free in the

mast jacket. See Section 9 for alignment of steering

column assembly if necessary.

2.
To check for proper shift linkage adjustment, lift

the transmission selector lever towards the steering

wheel. Allow the selector lever to be positioned in

drive (D) by the transmission detent.

NOTE: Do not use the indicator pointer as a

reference to position the selected lever. When

performing linkage adjustment, pointer is ad-

justed last.

3.
Release the selector lever. The lever should be in-

hibited from engaging low range unless the lever is

lifted.

4.
Lift the selector lever towards the steering wheel,

and allow the lever to be positioned in neutral (N) by

the transmission detent.

5.
Release the selector lever. The lever should now

be inhibited from engaging reverse range unless the

lever is lifted.

6. A properly adjusted linkage will prevent the selector

lever from moving beyond both the neutral detent, and

the drive detent unless the lever is lifted to pass

over the mechanical stop in the steering column.

7.
In the event that an adjustment is required, place

the selector lever in drive (D) position as determined

by the transmission detent. See Steps 2 and 3.

8. Loosen the adjustment swivel at the cross-shaft,

and rotate the transmission lever so that it contacts

the drive stop in the steering column.

9. Tighten the swivel and recheck the adjustment. See

2 and 6.

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-31

with the "white" stripe painted on the engine

side of the flywheel outer rim, denoting the

"heavy" side of the engine.

1.
Mount transmission on transmission lifting equip-

ment installed on jack or other lifting device.

2.
Remove converter holding tool.

CAUTION: Do not permit converter to move

forward after removal of holding tool.

3.
Raise transmission into place at rear of engine and

install transmission case to engine upper mounting

bolts,
then install remainder of the mounting*bolts.

Torque bolts to 35 ft. lbs.

4.
Remove support from beneath engine, then raise

rear of transmission to final position.

5. Through flywheel cover opening align as closely as

possible the "white" flywheel balance mark stripe

and the "blue" painted stripe on the end of converter

cover and housing. If scribed during removal, align

scribe marks on flywheel and converter cover. In-

stall converter to flywheel attaching bolts. Torque

bolts to 15-20 ft. lbs.

6. Install converter under pan.

7. Reinstall transmission support crossmember to

transmission and frame.

8. Remove transmission lift equipment.

9. Connect propeller shaft to transmissions.

10.
Connect manual and TV control lever rods to

transmission.

11.
Connect oil cooler lines (if so equipped), vacuum

Fig.
13PG - Converter Holding Tool
modulato:* line, and speedometer drive cable to

transmission.

12.
Refill transmission through filler tube, using Funnel

J-4264 and following the recommended procedure

provided earlier in this section.

13.
Check transmission for proper operation and for

leakage. Check and, if necessary, adjust linkage.

CORVETTE POWERGLIDE TRANSMISSION

Replacement

1.
Disconnect battery ground cable.

2.
Remove ball end from transmission shift control

lever.

3.
Raise front and rear of vehicle.

4.
Insert a block of wood between the top of the dif-

ferential carrier housing and the underbody (to

prevent upward travel of the carrier when the car-

rier front support is disconnected).

5. Disconnect the differential carrier front support

from its frame bracket, by removing the nut on the

underside of the biscuit mount.

6. Pry the carrier downward to relieve load while re-

moving the two center mounting bolts from the

carrier front support. (To pry carrier downward

insert crowfoot end of a pry bar**hrough the open-

ing in the carrier front support, hooking end of bar

over top of the center mounting bolt pad cast in the

underside of the carrier).

7. Pivot carrier support downward for access to prop

shaft "U"-joint.

8. Disconnect prop shaft front and then rear
"U"
bolts.

9. Disconnect parking brake cable from ball socket at

idler lever located near center of underbody.

10.
Remove prop shaft by moving shaft forward.

11.
Remove left bank exhaust pipe.

12.
Remove right bank exhaust pipe and heat riser.

13.
Disassemble the transmission mount, as follows:

a. Remove the two bolts that attach rear mount

cushion to the rear mount bracket.

b.
Support engine under oil pan and raise engine to

remove load from rear mount cushion.

CAUTION: To avoid damage to oil pan, a suit-

able wide base, heavy wood platform should be

placed between the jack pad and the oil pan.

c. Remove the three transmission mount bracket-

to-crossmember bolts, then remove mount

bracket.

d. Remove the two bolts from mount pad to trans-

mission case and remove rubber mount cushion

and exhaust pipe "yoke".

14.
Disconnect oil cooler lines at transmission and

swing lines clear.

15.
Remove connector underpan.

16.
Remove converter to flywheel attaching bolts.

17.
At transmission disconnect vacuum modulator line

and speedometer cable.

18.
Disconnect transmission shift linkage from trans-

mission gearshift control lever. Remove shift lever.

19.
At transmission, remove throttle valve linkage and

disconnect neutral safety switch linkage, also re-

move the gearshift control linkage.

20.
Remove neutral safety switch from transmission

control bracket.

CHEVROLET CHASSIS SERVICE

CLUTCH AND TRANSMISSIONS 7-32

21.
Remove transmission output shaft slip yoke and in-

sert a plastic shipping plug in end of extension to

prevent spillage of transmission fluid.

NOTE:
The yoke is removed to avoid tearing

the heat reflecting pad on the underbbdy, when

the transmission is being removed.

22.
Remove bright metal ignition shielding from dis-

tributor area.

23.
Remove the transmission dip stick and tube

assembly.

24.
Disconnect transmission vacuum modulator line at

distributor advance line tee.

25.
Position transmission hoist under transmission and

attach safety chain to transmission.

26.
Remove transmission converter housing-to-engine

attaching foolts and slide transmission rearward.
NOTE:
Observe converter when moving trans-

mission rearward. If converter does not move

with the transmission, pry it free of flywheel

before proceeding.

27.
Install converter retaining strap.

28.
Lower and remove transmission from vehicle by

tilting the front down and to the right while inter-

mittently lowering the transmission to facilitate its

• removal.

29.
Reinstall transmission assembly by performing the

above steps in reverse order.

Bolt Torques

Transmission Case to Flywheel

Housing Bolts 35 ft. lbs.

Converter to Flywheel Bolts. . , . . 35 ft. lbs.

OTHER SERVICE OPERATIONS

Although certain operations, such as oil pan or gasket

replacement, valve body, governor, filler pipe "O" ring,

speedometer drive gear, case extension "0" ring and

rear oil seal, vacuum modulator, and servo cover or

gasket service may be performed from underneath the
vehicle without removing the Powerglide; their service

procedure is covered in the Passenger Overhaul Manual

and is not repeated here. Refer to the- Powerglide Sec-

tion of the Passenger Overhaul Manual for all other

service operations not covered here.

DIAGNOSIS

Proper operation of the Powerglide transmission may

be affected by a number of factors, all of which must be

considered when trouble in the unit is diagnosed.

Proper trouble diagnosis can only be accomplished

when performed in a thorough step by step procedure.

The following procedure has been devised and tested and

is recommended for all trouble diagnosis complaints and

if the service man will follow this checking procedure,

accurate and dependable diagnosis may be accomplished.

This will result in a savings of time, not only to the

service man, but to the customer as well.

WARMING UP TRANSMISSION

Before attempting to check and/or correct any com-

plaints on the Powerglide transmission it is absolutely

essential that the oil level be checked and corrected if

necessary. An oil level which is either too high or too

low can be the cause of a number of abnormal conditions

from excessive noise to slippage in all ranges.

It must be remembered that cold oil will slow up the

action of the hydraulic controls in the transmission. For

this reason a trouble or oil leak diagnosis should not be

attempted until the transmission has been warmed up by

either of the following procedures:

Shop Warm Up

1.
Connect tachometer to engine.

2.
Set parking brake tight and start engine.

3.
Place selector light in
"D"
(drive) range.

4.
Adjust carburetor idle speed adjusting screw to run

engine at approximately 750 rpm and operate in this

manner for two minutes. At the end of two minutes

of operation, the transmission will be sufficiently

warmed up for diagnosis purposes.
NOTE:
At this point, readjust the engine idle

speed to 450-475 rpm in
"D"
range.

Road Warm Up

Drive the car approximately 5 miles with frequent

starts and stops.

NOTE:
At this point, make sure the engine idle

speed is set to 450-475 rpm in
"D"
range.

CHECKING FLUID LEVEL AND CONDITION

After transmission has been warmed up, check the

fluid level with the engine idling, parking brake set and

control lever in "N" (neutral). If the fluid level is low,

add fluid to bring level up to the full mark on gauge rod,

CAUTION: If fluid level is too high, fluid may

be aerated by the planet carrier. Aerated fluid

will cause turbulence in the converter which will

result in lost power, lower stall speed and lower

pressures in control circuits. Lower fluid level

to full mark, then shut off engine to allow air

bubbles to work out of fluid.

When checking oil level, aburned smell and discolora-

tion indicate burned clutches or bands and the transmis-

sion will have to be removed.

MANUAL LINKAGE

Manual linkage adjustment and the associated neutral

safety switch are important from a safety standpoint.

The neutral safety switch should be adjusted so that the

engine will start in the Park and Neutral positions only.

With the selector lever in the Park position, the park-

ing pawl should freely engage and prevent the vehicle

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-37

LI.
- LI Range can be selected at any vehicle speed,

and the transmission will shift to second gear

and remain in second until vehicle speed is re-

duced to approximately 40 MPH, .depending on

axle ratio. LI Range position prevents the trans-

mission from shifting out of first gear.
It is very important that any communication concerning

the Turbo Hydra-Matic always contain the transmission

serial number and that all transmission parts returned

to Chevrolet Motor Division always be tagged with the

transmission serial number.

MAINTENANCE AND ADJUSTMENTS

TRANSMISSION FLUID

Transmission fluid level should be checked with trans-

mission warm and selector lever in "P" Park position,

every time engine oil level is checked or as specified in

Section 0 when engine oil is changed.

CAUTION: Since the Turbo Hydra-Matic trans-

mission is very sensitive to oil level, special

precautions should be taken when checking the

oil level, to insure against an overfifE

Transmission fluid should be changed as specified in

Section 0.

FLUID LEVEL INDICATOR

The fluid level indicator is located in the filler pipe at

the right rear corner of the engine. To bring the fluid

level from the add mark to the full mark add 1 pint.

Fluid level should be to the full mark with transmission

at normal operating temperature. With cold fluid the

level should be at the add mark or slightly below.

SHIFT CONTROL LINKAGE ADJUSTMENT

Adjust linkage as shown below and in Figure 2.

1.
The shift tube and lever assembly must be free in the

mast jacket See Section 9 for alignment of steering

column assembly if necessary.

2.
To check for proper shift linkage adjustment, lift the

transmission selector lever towards the steering

wheel. Allow the selector lever to be positioned in

drive (D) by the transmission detent.

NOTE: Do not use the indicator pointer as a

reference to position the selector lever. When

performing linkage adjustment, pointer is ad-

justed last.

3.
Release the selector lever. The lever should be in-

hibited from engaging low range unless the lever is

lifted.

4.
Lift the selector lever towards the steering wheel,

and allow the lever to be positioned in neutral (N) by

the transmission detent.

5.
Release the selector lever. The lever should now be

inhibited from engaging reverse range unless the

lever is lifted.

6. A properly adjusted linkage will prevent the selector

lever from moving beyond both the neutral detent,

and the drive detent unless the lever is lifted to pass

over the mechanical stop in the steering column.

See schematic diagram.

7.
In the event that an adjustment is required, place the

selector lever in drive (D) position as determined by

the transmission detent. See Steps 2 and 3.

8. Loosen the adjustment swivel at the cross-shaft, and
rotate the transmission lever so that it contacts the

drive stop in the steering column.

9. Tighten the swivel and recheck the adjustment. See

Steps 2 and 6. -

l(h Readjust indicator needle if necessary to agree with

the transmission detent" positions. See Section 9.

11.
Readjust neutral safety switch if necessary to pro-

vide the correct relationship to the transmission de-

tent positions. See Section 12.

12.
When properly adjusted the following conditions must

be met by manual operation of the steering column

shift lever:

a. From reverse to drive position travel, the trans-

mission detent feel must be noted and related to

indicated position on dial.

b.
When in drive and reverse positions, pull lever

rearward (towards steering wheel) and then re-

lease. It must drop back into position with no

restrictions.

NEUTRAL SAFETY SWITCH ADJUSTMENT

The neutral safety switch must be adjusted so that the

car will start in the park or neutral position, but will not

start in the other positions. For replacement refer to

Section 12 of this Manual.

DRAINING AND REFILLING TRANSMISSION

Drain oil immediately after operation before it has had

an opportunity to cool.

To drain oil proceed as follows:

1.
Remove bottom pan attaching screws, pan, and gas-

ket.

2.
Remove oil strainer. Remove "O" ring seal from

pick-up pipe and discard.

3.
Discard strainer if dirty.

4.
Install new "O" ring seal on pick-up pipe and install

strainer and pipe assembly.

5.
Thoroughly clean bottom pan.

6.. Affix new gasket to bottom pan with petroleum jelly.

7.
Install bottom pan with attaching screws and torque

to specifications;

8. If only the pan has been removed, pour approximately

7-1/2 pints of fluid into the transmission. If the

valve body has also been removed use 9-1/2 pints.

After a complete overhaul approximately 19 pints

are required. Be sure container, spout, or funnel is

clean.

9. Start engine and let idle (carburetor off fast idle

step).
Place selector lever in P position and apply

hand brake.

10.
With transmission warm (approximately 150°F), add

fluid to bring level to full mark on indicator.

CAUTION: Do not overfill. Foaming will re-

sult.

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-2

Fig.
1—Cover
Attaching Bolts—Chevy li Shown

ADJUSTMENTS

STEERING
GEAR

Before any adjustments are made to the steering gear

in an attempt to correct such conditions as shimmy,

loose or hard steering etc., a careful check should be

made of front end alignment, shock absorbers, wheel

balance and tire pressure for possible cause.

Correct adjustment of the steering gear is very im-

portant. Perform adjustments following the sequence

listed below,

1.
Remove pitman arm nut and mark relation of pitman

arm position to sector shaft. Remove pitman arm

with Tool J- 6632 as shown in Figure 2.

2.
Loosen the pitman shaft lash adjuster screw locknut

and turn the adjuster screw a few turns in a counter-

clockwise direction (fig. 3). This removes the load
Fig. 2—Removing Pitman Arm

imposed on the worm bearings by the close meshing

of rack and sector teeth. Turn steering wheel gently

in one direction until stopped by gear, then back away

about one turn.

CAUTION: Do not turn steering wheel hard

against stops when steering relay rod is discon-

nected as damage to ball guides may result.

3.
All except Corvette and telescopic columns:

a. Disconnect steering column harness at chassis

wiring connector plug.

b.
Remove horn cap or ornament and using an inch

pound torque wrench and socket on steering wheel

nut, measure torque required to keep the wheel

in motion.

LASH ADJUSTER

SCREW

LOCK NUT

WORM BEARING

ADJUSTER
\

WORM

ADJUSTER

Fig.
3—Steering Gear Adjustment Points

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-3

Fig.
4-Checking Wheel PuI!-Corvette

c. If torque does not lie within limits given in speci-

fications at rear of manual, adjustment is

necessary.

4.
Corvette and telescopic columns:

a. Use Tool J-5178 to measure.pull at rim of wheel

required to keep wheel in motion (fig. 4).

b.
If pull does not lie within limits given in specifi-

cations in rear of manual, adjustment of worm

bearings is necessary.

NOTE:
If vehicle is equipped with a tilt steer-

ing column, it will be necessary to disconnect

the steering coupling to obtain a torque reading

of the steering column. This torque should then

be subtracted from any reading taken on the

gear.

5. To adjust worm bearings, loosen worm bearing ad-

juster locknut and turn worm bearing adjuster shown

in Figure 3 until there is no perceptible end play in

worm. Check pull at steering wheel, readjusting: if

necessary to obtain proper pull. Tighten locknut and

recheck pull. If the gear feels "lumpy" after adjust-

ment of worm bearings, there is probably damage in

the bearings due to severe impact or to improper

adjustment and the gear must be disassembled for

replacement of damaged parts.

6. After proper adjustment of worm is obtained and all

mounting bolts securely tightened, adjust lash ad-

juster screw. First turn the steering wheel gently

from one stop all the way to the other, carefully

counting the total number of turns. Then turn wheel

back exactly half way, to center position. Turn lash

adjuster screw clockwise to take out all lash in gear

teeth, and tighten locknut. Check pull at steering

wheel taking highest reading as wheel is turned

through center position. See specifications in rear of

manual for proper sector lash adjustment. Readjust

if necessary to obtain proper pull.
NOT MORE THAN

T/a INCH FROM

CENTERLINE

Fig.
5—Steering Wheel Alignment

NOTE:
If maximum specification is exceeded,

turn las£ adjuster screw counterclockwise, then

come up on adjustment by turning the adjuster in

a clockwise motion.

7. Tighten locknut then recheck pull, as it must lie be-

tween specified readings.

Fig.
6—Adjusting Steering Ratio—Corvette

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-4

8. Reassemble pitman arm to sector shaft, lining up

marks made during disassembly. Refer to torque

specifications at rear of manual for correct torque

value.

9. Install horn cap or ornament and connect steering

column harness at chassis connector.

NOTE:
Chevy.n models are equipped with a

shim at the frame to steering gear mounting

bolts.
Shims may be removed or installed as

required for proper steering gear alignment.

STEERING WHEEL ALIGNMENT AND

HIGH POINT CENTERING

1.
Set front wheels in straight ahead position. This can

be checked by driving vehicle a short distance on a

flat surface to determine steering wheel position at

which vehicle follows a straight path.

2.
With front wheels set straight ahead, check position

of mark on wormshaft designating steering gear high

point. This mark should be at the top side of the shaft

at 12 o'clock position and lined up with the mark in

the coupling lower clamp.

3.
If gear has been moved off high point when setting

wheels in straight ahead position, loosen adjusting

sleeve clamps on both left and right hand tie rods,

then turn both sleeves an equal number of turns in

the same direction to bring gear back on high point.

CAUTION: Turning the sleeves an unequal
number of turns or in differential directions will

disturb the toe-in setting of the wheels.

4.
Readjust toe-in as outlined in Section 3 (if necessary).

5. With wheels in a straight ahead position and the

steering gear on highpoint, check the steering wheel

alignment by measuring the distance from each hori-

zontal spoke to the horizontal centerline of the

steering wheel (fig. 5). If the horizontal spokes are

over 1-1/8 inches from the horizontal position the

wheel should be removed and centered. (See steering

wheel removal in this section.)

TOE-IN ADJUSTMENT

Adjust the steering linkage for proper toe-in setting as

outlined in Section 3.

CORVETTE STEERING RATIO (Fig. 6)

The Corvette steering ratio may be changed as follows:

CAUTION: Do not use the rearward hole in the

steering arm with power steering equipment or

interference may result.

1.
Remove tie rod ball stud nut at steering arm and

disconnect tie rod from steering arm.

2.
Move tie rod end to forward hole for 17.6:1 ratio

(fast ratio) or rear hole for 20.2:1 ratio (standard

ratio).

3.
Install tie rod stud nut and tighten securely. Repeat

operation on opposite steering arm.

COMPONENT REPLACEMENT AND REPAIRS

STEERING WHEEL

REGULAR PRODUCTION (Fig. 7)

Removal

1.
Disconnect steering column harness from chassis

wiring harness at connector (fig. 8).

2.
Pull out horn button cap or center ornament and

retainer.

3.
Remove three screws from the receiving cup.

4.
Remove the receiving cup, belleville spring, bushing,

and pivot ring.

5. Remove the steering wheel nut and washer.

6. Using Tool J-2927, install centering adapter on

steering shaft, thread puller anchor screws into

threaded holes provided in steering wheel. Turn

center bolt of tool clockwise to remove steering

wheel (fig. 9).

Installation

CAUTION: Direction signal control assembly

must be in "neutral position when assembling

steering wheel to prevent damage to cancelling

cam and control assembly.

1.
With directional cancelling cam and horn contact as-

sembly in place, set wheel onto steering shaft.
Fig. 7—-Regular Wheel and Horn Attachments

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-5

Fig.
8—Steering Column Wiring Connector

Secure with washer and nut. Refer to torque speci-

fications at rear of manual for correct torque values.

Install belleville spring (with dish of spring up), pivot

ring, bushing and receiving cup with screws.

Install retainer and horn button cap or center

ornament.

Connect steering column harness to chassis wiring

connector.

Fig.
9—Removing Steering Wheel with J-2927
Fig.
10—Simulated Wood Steering Wheel and Attaching Parts

SIMULATED WOOD (Fig. 10)

Removal

1.
Disconnect steering column harness from chassis

wiring harness at connector.

2.
Remove horn cap assembly by pulling up.

3.
Remove contact assembly attaching screws and re-

move contact assembly.

NOTE:
If steering wheel only is to be replaced,

perform step 4. If directional signal cancelling

cam is to be replaced, omit step 4 and proceed

with steps 5 and 6.

4.
Remove remaining screws from steering wheel and

remove wheel from hub assembly.

5. Remove steering wheel nut and washer.

6. Using Tool J-2927, install centering adapter on

steering shaft, thread puller anchor screws into

threaded holes provided in hub assembly. Turn

center bolt of tool clockwise to remove hub

assembly.

Installation

CAUTION: Directional signal control assembly

must be in neutral position when assembling hub

assembly to prevent damage to cancelling cam

and control assembly.

1.
With directional cancelling cam and horn contact in

place, install hub assembly on steering shaft. Secure

with washer and nut. Refer to torque specifications

at rear of manual for correct torque value.

2.
Attach steering wheel to hub assembly using the six

attaching screws and tighten securely.

3.
Place horn contact on steering wheel and attach with

three screws. Tighten securely.

4.
Snap horn button in place.

5. Connect steering column harness to chassis wiring

connector.

CORVETTE TELESCOPING (Fig. 11)

Removal

1.
Disconnect steering column harness at wiring

connector.

2.
Pry off horn button cap.

3.
Remove three screws securing horn contact to spacer

and hub.

4.
Remove two screws securing lock screw to lock

knob,
and remove lock screw, lock knob, and spacer.

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-6

Fig.
11
—Corvette Telescoping Wheel Option

5.

7.
NOTE:
If steering wheel only is to be replaced,

perform Step 5 below only. If directional signal

cancelling cam is to be replaced, omit Step 5

and proceed with Steps 6 and 7.

Remove six screws securing steering wheel to hub

and remove wheel.

Remove nut and washer from shaft and using steering

wheel puller Tool J-2927, remove steering wheel and

hub from vehicle.

Slide cancelling cam and spring off shaft.

Installation

NOTE:
Refer to torque specifications at rear of

manual for correct torque values.

1.
If necessary, slide cancelling cam and spring on end

of shaft.

2.
If hub was removed from steering wheel, attach hub

to steering wheel with screws removed during dis-

assembly.

3.
Place steering wheel and hub assembly in position

and secure to column with washer and nut.

4.
Position spacer on steering wheel.
5. Position lock knob on steering wheel.

6. Install lock screw through lock knob, turn into shaft,

and adjust to lock position.

7. Attach spacer to wheel with three screws.

8. Place lock knob in lock position and attach to lock

screw with two screws.

9. Remove three screws holding spacer. Attach horn

contact to spacer and steering wheel with three

screws.

10.
Install horn button cap.

11.
Connect steering column harness at chassis plug.

STEERING COUPLING (Fig. 12)

Removal

NOTE:
Chevy n models are equipped with a

clamp arrangement rather than the conventional

"rag joint" steering coupling. Refer to Steering

Gear - Chevy II, for service procedures.

1.
Remove nuts and washers securing steering coupling

to flanged end of steering column (fig. 12).

2.
Remove coupling clamp bolt (fig. 12) and slightly

spread coupling clamp.

CHEVROLET CHASSIS SERVICE MANUAL