check engine CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

LUBRICATION 0-14

SAE 5W-30 oils may be used during periods when

temperatures of 32° and below are to be expected.

Types of Oils

In service, crankcase oils may form sludge and varnish

and under some conditions, corrosive acids unless pro-

tected against oxidation.

To minimize the formation of these harmful products

and to assure the use of oil best suited for present day

operating conditions, automobile manufacturers have de-

veloped a series of sequence tests designed to evaluate

the ability of any oil to properly lubricate automobile

engines.

It is recommended that only those oils which are

certified by their suppliers as meeting or exceeding the

maximum severity requirements of these sequence tests

(or GM Standard 4745-M) be used in Chevrolet engines.

Certified sequence tested oils will be described as such

on their containers.

Maintaining Oil Level

The oil gauge rod is marked "Full" and "Add Oil."

These notations have broad arrows pointing to the level

lines.
The oil level should be maintained between the

two lines, neither going above the "Full" line nor under

the "Add Oil" line. DO NOT OVERFILL. After operating

vehicle allow a few minutes for oil to return to crankcase

before checking oil level.

Check the oil level frequently and add oil when

necessary.

Oil and Filter Change Intervals

NOTE:
Under prolonged dusty driving condi-

tions,
it is recommended that these operations

be performed more often.

OIL

To insure continuation of best performance, low main-

tenance cost and long engine life, it is necessary to

change the crankcase oil whenever it becomes contami-

nated with harmful foreign materials. Under normal

driving conditions draining the crankcase and refilling

with fresh oil every 60 days or every 6000 miles which-

ever occurs first, is recommended.

It is always advisable to drain the crankcase only after

the engine has become thoroughly warmed up or reached

normal operating temperature. The benefit of draining is,

to a large extent, lost if the crankcase is drained when

the engine is cold, as some of the suspended foreign

material will cling to the sides of the oil pan and will not

drain out readily with the cold, slower moving oil.

OIL FILTER

Change engine oil filter every 6000 miles or every 6

months, whichever occurs first.

NOTE:
For Vehicles in heavy duty operation

involving continuous start-stop or prolonged idl-

ing, engine oil should be changed after 2500-

3000 miles of operation. The filter should be

changed after 5000-6000 miles of operation.
Crankcase Dilution

Probably the most serious phase of engine oil deterio-

ration is that of crankcase dilution which is the thinning

of the oil by fuel vapor leaking by pistons and rings and

mixing with the oil and by condensation of water on the

cylinder walls and crankcase.

Leakage of fuel, or fuel vapors, into the oil pan occurs

mostly during the "warming up" period when the fuel is

not thoroughly vaporized and burned. Water vapor enters

the crankcase through normal engine ventilation and

through exhaust gas blow-by. When the engine is not

completely warmed up, these vapors condense, combine

with the condensed fuel and exhaust gases and form acid

compounds in the crankcase.

As long as the gases and internal walls of the crank-

case are hot enough to keep water vapor from con-

densing, no harm will result. However, when the engine

is run in low temperatures moisture will collect and

unite with the gases formed by combustion resulting in

an acid formation. The acid thus formed is likely to

cause serious etching or pitting which will manifest itself

in excessively rapid wear on piston pins, camshaft

bearings and other moving parts of the engine, oftentimes

causing the owner to blame the car manufacturer or the

lubricating oil when in reality the trouble may be traced

back to the character of fuel used, or a condition of the

engine such as excessive blowby or improper carburetor

adjustment.

Automatic Control Devices to Minimize

Crankcase Dilution

All engines are equipped with automatic devices which

aid greatly in minimizing the danger of crankcase

dUution.

The thermostat, mounted in the cylinder head water

outlet, restricts the flow of water to the radiator until a

predetermined temperature is reached, thus minimizing

the length of time required to reach efficient operating

temperature, reducing the time that engine temperatures

are conducive to vapor condensation.

A water by-pass is included in the cooling system,

utilizing a hole in the front of, the cylinder block. This

allows a limited circulation of coolant, bypassing the

thermostat until thermostat opening temperatures are

reached. This system provides a uniform coolant tem-

perature throughout the engine, eliminating localized

hot-spots, improving exhaust valve life, provides fast

warmrup of lubricating oil and fast temperature rise in

the coolant which provides fast heater operation in cold

weather.

A thermostatic heat control on the exhaust manifold

during the warming up period, automatically directs the

hot exhaust gases against the center of the intake mani-

fold, greatly aids in proper vaporization of the fuel.

An automatic choke reduces the danger of raw or

unvaporized fuel entering the combustion chamber and

leaking into the oil reservoir.

An.
efficient crankcase ventilating system drives off

fuel vapors and aids in the evaporation of the raw fuel

and water which may find its way into the oil pan.

CRANKCASE BREATHER CAP

Clean and re-oil at every oil change..

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-15

CRANKCASE VENTILATION VALVE

VALVE TYPE

NOTE: Under prolonged dusty driving condi-

tions,
it is recommended that these operations

be performed more often. Every 12,000 miles

or 12 months the valve should be replaced.

Connecting hoses, fittings, flame arrestor and

crankcase breather cap (where used) should be

cleaned. At every oil change the system should

be tested for proper function and serviced, if

necessary.

FUEL FILTER

Replace filter element located in carburetor inlet if

flooding occurs, if engine surges during constant speed

operation (pulsating effect) or if poor performance is

experienced during acceleration or at higher speeds.

AIR CLEANER

NOTE: Under prolonged dusty driving condi-

tions,
it is recommended that these operations

be performed more often.

POLYURETHANE TYPE-

Every 12,000 miles clean element in solvent, squeeze

out solvent, then soak in engine oil and squeeze out

excess.

OIL WETTED PAPER ELEMENT TYPE-

First 12,000 miles inspect or test element; if satis-

factory, re-use element but recheck every 6,000 miles

until replaced. Element must not be washed, oiled,

tapped or cleaned with an air hose.

BATTERY TERMINAL WASHERS

Battery terminals have felt washers between top of

case and cable connections to minimize corrosive action

of battery acid. These felt washers should be saturated

with engine oil every 6,000 miles.

DISTRIBUTOR

4 and 6-Cylinder Engine—Remove distributor cap and

rotate lubricator 1/2 turn at 12,000 mile intervals. Re-

place at 24,000 mile intervals.

8-Cylinder Engine—Change cam lubricator end for end

at 12,000 mile intervals. Replace at 24,000 mile

intervals.

REAR AXLE AND 3-SPEED AND

OVERDRIVE, 4-SPEED TRANSMISSIONS

The passenger car operates under the most severe

lubrication conditions at high speed and requires a hypoid

lubricant which will meet this condition.

Recommended Lubricants

Standard Rear Axles—SAE 90 "Multi-Purpose" gear

lubricant.

Positraction Rear Axles—Use special Positraction

lubricant.
CAUTION: Straight Mineral Oil gear lubricants

must not be used in hypoid rear axles.

Transmissions—SAE 90 "Multi-Purpose" gear

lubricant.

The SAE 90 viscosity grade is recommended for year

round use. However, when extremely low temperatures

are encountered for protracted periods during the winter

months, the SAE 80 viscosity grade may be used.

"Multi-Purpose" Gear Lubricants

Gear lubricants that will satisfactorily lubricate hypoid

rear axles have been developed and are commonly re-

ferred to as ' 'Multi-Purpose" gear lubricants meeting

U.S.
Army Ord. Spec. MIL-L-2105B.

These lubricants can also be satisfactorily used in

manual transmissions.

CAUTION: With Positraction rear axles use

special Positraction lubricant.

"Multi-Purpose" gear lubricants must be manufac-

tured under carefully controlled conditions and the

lubricant manufacturer must be responsible for the

satisfactory performance of his product. His reputation

is the best indication of quality.

Lubricant Additions

The lubricant level in the axle and transmission hous-

ings should be checked periodically. (Every 6,000 miles.)

It is recommended that any additions required to bring

up the lubricant level be made using the same type lubri-

cant already in the housing.

When checking lubricant level in transmission or rear

axle the unit being cheeked should be at operating

temperature. With unit at operating temperature the

lubricant should be level with bottom of the filler plug

hole.
If the lubricant level is checked with the unit cold

the lubricant level should be 1/2 inch below the filler

plug hole.

Lubricant Changes

The rear axle lubricant does not require changing for

the life of the vehicle. If additions are needed, or when

refilling the axle after service procedures, use lubricants

described above.

POWERGLIDE TRANSMISSION

NOTE: Every 12,000 miles, it is recommended

that the Powerglide low band be adjusted as

specified in Section 7 of this manual.

Every 6,000 miles--Check fluid level on dipstick with

engine idling, selector lever in neutral position, parking

brake set and transmission at operating temperature. If

fluid level is below full mark on dip stick, adding a small

amount of Automatic Transmission Fluid, General Motors

Automatic Transmission Fluid (Part Numbers 1050568-

69,
70) is recommended. If this fluid is not obtainable,

use Automatic Transmission Fluid Type 'A' bearing the

mark AQ-ATF followed by a number and the suffix letter

'A'.
Recheck fluid level on dip stick and again add a

small amount of fluid if needed to bring level to full

mark. DO NOT OVERFILL.

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-5

them in their proper location. (See Figure 8)

12.
Refill radiator.

Defroster Duct

Figure 9 illustrates the defroster duct installation

on Chevrolet, Chevelle and Camaro vehicles.

Bowden Cobles

Bowden cable attachment should be made in the fol-

lowing manner:

1.
With the cables attached to the control assembly

and levers, move the levers to their fully left or

closed position.

2.
Attach cable wires to the heater valve levers and

tighten cable attaching bracket screws.

3.
Check for proper cable operation and readjust as

necessary.

Control Panel

Control panel installation is shown in Figures 10, 11,

and 12.

Fan Switch

Replacement

1.
Remove control assembly-to-instrument panel re-

inforcement attaching screws and push the control

assembly toward the front of the vehicle and down.

2.
Remove the two switch attaching screws and the

electrical connector.

3.
Replace switch, screws, and electrical connector.

4.
Place control assembly into instrument panel and

replace attaching screws.

Resistor

The resistor assembly is attached to the heater dis-

tributor assembly. It should "be replaced if low or

medium blower speed is inoperative. Remove the glove

box for access to the unit.
HEATER HOUSING

LOWER RIGHT HAND

RETAINER NUT

Fig.
6—Air Distributor Duct (Camaro)
Fig.
7—Access to Blower and Housing (Chevelle)

CHEVY II

Heater Assembly

Removal (Fig. 13)

1.
Drain radiator.

2.
From within engine compartment;

a. Remove heater hoses from heater inlet and outlet

connections.

b.
Remove three nuts around blower motor attaching

heater assembly to dash panel.

3.
From within vehicle:

a. Remove glove box and glove box door.

b.
Remove screw attaching distributor bracket to

dash.

c. Remove the screw attaching case bracket to the

adapter assembly bracket.

d. Carefully detach heater assembly from dash panel

and adapter assembly and lower it toward floor of

vehicle.

e. Disconnect all bowden cable connections, the

wiring connector and the defroster hoses.

4.
Remove the heater assembly from the vehicle.

Core Replacement

1.
'With the heater assembly removed from the vehicle,

remove the screws attaching the core cover to the

heater assembly.

2.
Remove the core mounting screws and remove the

core from the assembly.

3.
Replace with a new core and replace the core cover.

Installation

1.
Be sure the adapter seal and blower motor seal are

in place and set into place beneath the instrument

panel.

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-10

PLATE RETAINERS

CORE BRACKET SCREWS

Fig.
18—Corvette Heater Core Removal

7. Place a protective covering (waterproof if possible)

over the carpeting under the heater.

8. Remove the two bowden cables from the instrument

panel and disconnect the wiring connectors from the

blower switch and from the resistor.

9. Carefully work the heater assembly out from beneath

the dash.

Core Removal

1.
Remove the heater assembly as described above.
2.
Remove the sheet metal nuts which retain the core

mounting plate to the core housing.

3.
Remove the screws attaching the core brackets to

the core mounting plate and separate the core and

plate. .

Installation

1.
Assemble the core to plate with non-hardening

sealer. Attach the core mounting screws.

2.
Attach the core and plate assembly to the case with

the two sheet metal nuts. The assembly is ready for

installation as described below.

Heater Assembly Installation

1.
Carefully position the heater assembly in place on

inner surface of dash panel, then install the blower

and air inlet assembly on heater studs extending

through to the engine side of the panel. Attach the

seven stud nuts.

2.
Install electrical connectors to the blower switch and

resistor and reinstall the bowden cables to the

instrument panel.

3.
Replace the blower electrical connectors.

4.
Replace the heater hoses. (See Figure 20)

5. Replace the battery and the radiator supply tank.

6. Refill the radiator and check for leakage.

7. Check heater operation and make control adjustments

as necessary.

8. Replace the console panels and the glove

compartment.

CHEVROLET CHASSIS SERVICE MANUAL

HEATER
AND AIR
CONDITIONING
1A-13

AIR CONDITIONING

INDEX

Page

General Description
1A-13

Four-Season System
1A-13

Controls
1A-16

Comfortron System
. 1A-18

System Components
lA-19

Controls
1A-20

Universal System
. .
1A-21

Chevy
n
All-Weather System
•
1A-21

Corvette Four-Season System
. 1A-22

General Information
. . . 1A-26

Precautions
in
Handling R-12
1A-26

Precautions
in
Handling Refrigerant Lines
1A-28

Maintaining Chemical Stability
in the

Refrigeration System
1A-28

Gauge
Set 1A-29

Charging Station
IA-29

Leak Testing
the
System
1A-29

Vacuum Pump
1A-30

Availability
of
Refrigerant-12
. . 1A-30

Compressor
Oil 1A-31

Compressor Serial Number
1A-31

Inspection
and
Periodic Service
1A-31

Pre-Delivery Inspection
1A-31

6,000 Mile Inspection
1A-32

Periodic Service
, 1A-32

Installing Gauge
Set to
Check System Operation
....
1A-32

Performance Test
1A-32

Performance Data lA-r33

Comfortron System Operational Test
1A-33

Chevrolet Comfortron Tester
1A-34

Complete System Checks
1A-35

Maintenance
and
Adjustments ......
1A-37

Evaporator Comtrol Valve (POA)
.
1A-37
Page

Thermostatic Switch
1A-37

Expansion Valve
1A-41

Engine Idle Compensator
. . .
1A-42

Evacuating
and
Charging Procedures
1A-42

Purging
the
System
1A-42

Evacuating
and
Charging
the
System
1A-43

Checking
Oil . 1A-43

Component Replacement
and
Minor Repair
1A-45

Refrigerant Line Connections
1A-45

Repair
of
Refrigerant Leaks
1A-46

Preparing System
for
Replacement
of

Component Parts
. 1A-46

Foreign Material
in the
System
.
1A-47

Condenser
.
1A-48

Receiver-Dehydrator
1A-48

Evaporator
1A-49

Expansion Valve
1A-57

Evaporator Control Valve (POA)
1A-59

Thermostatic Switch
or
Blower Switch
. .
1A-59

All Weather-Pull Cable
1A-61

Blower Assembly
1A-62

Air Inlet Valve
.
1A-64

Blower
and
Evaporator Assembly
1A-64

Air Distributor Assembly
and
Outlet Ducts ...... 1A-64

Comfortron Automatic Control Components
1A-66

Collision Procedure lA-70

Four-Season Heater Components
1A-73

Comfortron Heater Components
. . . 1A-75

Compressor
1A-76

Wiring Diagrams
1A-78

Special Tools
.
1A-84

GENERAL DESCRIPTION

Four
air
conditioning systems
are
covered
in
this

section. They are:

1.
The
Four-Season System (Chevrolet, Chevelle,

Camaro and Corvette).

2.
The Comfortron System (Chevrolet).

3.
The All Weather System (Chevy n).

4.
The Universal System (Chevrolet, Chevelle, Chevy
n,

Camaro)

Underhood components (that
is, the
compressor,
con-

denser
and
receiver-dehydrator)
are
much
the
same
in

type,
location
and
method
of
attachment
on all of
the

above systems. The six-cylinder reciprocating compres-

sor
is
bracket-mounted
to the
engine
and
belt driven

from
the
crankshaft pulley.
The
condenser
is
mounted

ahead
of the
engine cooling radiator
and the
receiver-

dehydrator
is
mounted
in
the refrigerant line downstream

of
the
condenser.
All
cooling system components
are

connected by means
of
flexible refrigerant lines.

Evaporator size
and
location differ from system
to

system
as do
methods
of
temperature control
and air

supply
and
distribution.

FOUR-SEASON SYSTEM

The Four-Season system used
in the
Chevrolet,

Chevelle, Camaro,
and
Corvette vehicles
may be
iden-

tified
by the
fact that
it
uses
an
evaporator pressure

control known
as the POA
(Pressure Operated Absolute)

suction throttling valve.
Both
the
heating
and
cooling functions
are
performed

by this system.
Air
entering
the
vehicle must pass

through
the
cooling unit (evaporator)
and
through
(or

around)
the
heating unit,
in
that order, and the system
is

thus referred to
as a
''reheat" system.

The evaporator provides maximum cooling
of the air

passing through
the
core when
the air
conditioning sys-

tem
is
calling
for
cooling.
The
control valve acts in the

system only
to
control
the
evaporator pressure
so
that

minimum possible temperature
is
achieved without core

freeze-up.
The
valve
is
preset,
has no
manual con-

trol,
is
automatically altitude compensated,
and non-

repairable.

The heater core will be hot
at
all times since no water

valve
is
present
in
the system.

System operation
is as
follows (See Figure 24 and 25):

Air, either outside
air or
recirculated
air
enters
the

system
and is
forced through
the
system by the blower.

As
the air
passes through
the
evaporator core,
it

receives maximum cooling
if
the
air
conditioning controls

are calling
for
cooling. After leaving
the
evaporator,

the
air
enters
the
Heater
and Air
Conditioner Selector

Duct Assembly where,
by
means
of
manually operated

diverter doors,
it is
caused
to
pass through
or to
bypass

the heater core
in the
proportions necessary
to
provide

the desired outlet temperature. Conditioned airflow then

enters
the
vehicle through either
the
floor distributor

duct
or the
dash outlets. Remember that the heater core

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-19

Transducer

The transducer will produce a vacuum output that is

completely adjustable by varying the input voltage which

is provided by the amplifier. An increase in the applied

voltage results in a reduced vacuum output.

Power Servo

The power servo receives a vacuum signal from the

transducer, and it is capable of assuming any position

that is called for by the sensors, amplifier, and trans-

ducer. The power servo performs the following functions:

1.
Positions the temperature mix door via the tern-

perature door link. The position of this door~"de-

termihes the portions of hot and cold air being

blended and discharged into the car.

2.
Operates the power servo vacuum valve which de-

termines the air flow paths for heating and air

conditioning.

3.
Contains a printed circuit board which controls the

blower speed. The power servo position determines

the blower speed, but the control lever switch can

override the blower program depending upon the

customer's preference.

4.
Contains the "Hi" blower delay thermistor and the

"master delay thermistor".

Outside Air Diaphragm

When there is no vacuum applied to the hose, the out-

side air door is closed under spring tension. With the

door closed, air is taken from the inside of the auto-

mobile and re-circulated. Applying vacuum to the dia-

phragm opens the door for outside air.

Mode Door Diaphragm

Located behind the duct work, the mode door diaphragm

directs the air flow out either the air conditioning outlets,

the heater floor outlet, or both the heater and air con-

ditioning outlets. This is a push-pull type diaphragm

actuated by vacuum through two hoses and controlled by

the power servo vacuum switch.

Defroster Door

The defroster door is in the defog position until vacuum

is applied to the actuator to obtain either full heat or full

de-ice position.

High Blower Delay Thermistor

The high blower delay thermistor is located on the

power servo housing under the power servo vacuum valve

and printed circuit board assemblies. The function of the

thermistor is to operate the blower at a reduced speed

when the control is in the HI FRONT position until the

residual cold air is discharged from the duct work. This

function occurs when the blower first comes "on" in cold

weather.

Vacuum Tank

During heavy acceleration, the vacuum supply from
the carburetor drops. The vacuum tank, using a^ check

valve, stores vacuum so that under these conditions

vacuum will be available for the Comfortron.

Thermal Vacuum Valve (Hot Water Vacuum Switch)

When engine coolant temperature reaches 75°F, the

valve opens and supplies vacuum to the outside air door

if the system is calling for outside air.

Master Delay Thermister

This thermistor delays the initial operation of the

blower when the system is in the heat mode. In cold

weather this allows outside ram air to flow through the

system thereby purging the cold air in the ducts gradually

until the coolant reaches about 105°F. Then, the termis-

tor passes enough current to energize the master delay

relay which powers the blower at about nine volts.

Vacuum Relay Valve

This relay valve will shut off transducer vacuum to the

power servo whenever the vacuum from the engine intake

manifold falls below the vacuum in the power servo

supply line (engine stopped or operating at low manifold

vacuum). This causes the power servo to be held in

position when the vacuum supply falls too low to maintain

servo control.

Vacuum Bleeder

A vacuum bleeder insures that the outside air door will

close (diaphragm will bleed down) after the system has

been shut down. This prevents outside air from entering

when starting the system on a cold day before the engine

coolant temperature reaches 75°F.

Sun—Ambient Sensor

The sun-ambient sensor measures the temperature of

the air entering the air intake grille in front of the wind-

shield. The sensor is exposed to sun light so that it can

lower the in-car temperature slightly when the sun

is shining.

Ambient Switch

The ambient switch operates the air conditioning com-

pressor clutch. When the outside temperature is above

40° F. the switch will be closed and the compressor will

be running. This switch is included as| part of the sun-

ambient sensor assembly, but operates independently.

Resistor Assembly

The blower resistors are located in the evaporator

housing. The printed circuit board switch in the power

servo determines which of the resistors is being used,

and as in conventional systems, the resistors control the

blower speed.

System Operation

When starting the Comfortron System in cold weather,

the following sequence of events occurs:

1.
Initially the system is inoperative. In LO FRONT

position the master delay thermistor is warming

(self-heating because current is flowing through it)

CHEVROLET CHASSIS SERVICE MANUAL

HEATER
AND AIR
CONDITIONING
1A-31

FIVE
AMP

TIME DELAY

FUSE

CORD
TO

110
AC
SOURCE
PUMP

INLET
PUMP DISCHARGE

OUTLET

Fig.
44—Vacuum Pump

the use of weighing equipment necessary with the larger

drum. The single can Valve J-6271 can be used for com-

pleting the charge and for miscellaneous operations such
Fig.
45-R-12 Disposable Cans

as flushing. The valves are installed by piercing the top

seal of the cans.

Evacuating and charging procedures later in this sec-

tion will make use of the J-8393 Charging Station which

uses the 25 lb. drum of refrigerant.

COMPRESSOR OIL

Special refrigeration lubricant should be used in the

system. It is available in 1 quart graduated bottles

through Parts Stock. This oil is as free from moisture

and contaminants as it is possible to attain by commercial

processes. This condition should be preserved by im-

mediately capping the bottle when not in use.

See "Air Conditioning System Capacities" for the

total system oil capacity.

Due to the porosity of the refrigerant hoses and con-

nections, the system refrigerant level will show a definite

drop after a period of time. Since the compressor oil is

carried throughout the entire system mixed with the

refrigerant a low refrigerant level will cause a dangerous

lack of lubrication. Therefore the refrigerant charge in

the system has a definite tie-in with the amount of oil

found in the compressor and an insufficient charge may

eventually lead to an oil build-up in the evaporator.

COMPRESSOR SERIAL NUMBER

The compressor serial number is located on the serial

number plate on top of the compressor. The serial num-

ber consists of a series of numbers and letters. This

serial number should be referenced on all forms and

correspondence related to the servicing of this part.

INSPECTION AND PERIODIC SERVICE

PRE-DELIVERY INSPECTION

1.
Check that engine exhaust is suitably ventilated.

2.
Check the belt for proper tension.

3.
With controls positioned for operation of the system,

operate the unit for ten minutes at approximately

2000 rpm. Observe the clutch pulley bolt to see that

compressor is operating at the same speed as the
clutch pulley. Any speed variation indicates clutch

slippage.

Before turning off the engine, check the sight glass

to see that the.unit has a sufficient Refrigerant

charge. The glass should be clear, although during

milder weather it may show traces of bubbles. Foam

in.
the flow indicates a low charge. No liquid visible

indicates no charge.

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-32

5.
Check hose clamp connections. If clamp screw torque

is less than 10 lb. in., retighten to 20-25 lb. in. Do

not tighten to new hose specifications or hose leak-

age may occur.

6. If there is evidence of an oil leak, check the com-

pressor to see that the oil charge is satisfactory.

7.
Check the system controls for proper operation.

6000 MILE INSPECTION

1.
Check unit for any indication of a refrigerant leak.

2.
If there is an indication of an oil leak, check the

compressor proper oil charge.

3.
Check sight glass for proper charge of Refrigerant-

12.

4.
Tighten the compressor brace and support bolts and

check the belt tension.

5.
Check hose clamp connections as in step 5 above.

6. Check thermostatic switch setting (Universal and

All-Weather Systems.)

PERIODIC SERVICE

• Inspect condenser regularly to be sure that it is not

plugged with leaves or other foreign material.

Fig.
46—Compressor Connector Block—Typical
• Check evaporator drain tubes regularly for dirt or

restrictions.

• At least once a year, check the system for proper

refrigerant charge and the flexible hoses for brittle-

ness,
wear or leaks.

• Every 6000 miles check sight glass for low refriger-

ant level.

• Check belt tension regularly.

• Every week - during winter months or other periods

when the system is not being operated regularly- run

the system, set for maximum cooling, for 10 or 15

minutes to insure proper lubrication of seals and

moving parts.

INSTALLING GAUGE SET TO CHECK

SYSTEM OPERATION

Compressor Suction and Discharge Connector

Compressor connector assemblies used on all vehicles

are of the same basic design consisting of the inlet

(suction) and outlet (discharge) connections, gauge fittings

and muffler and, in general, the assemblies differ only in

the location of the gauge fittings.

On Universal and Four-Season Systems the outlet line

extends along side of and toward the front of the com-

pressor and the muffler in the line is bracket mounted to

the compressor body. In all Universal Systems the gauge

fittings for both low and high pressure sides of the sys-

tem are located in the connector body. On Four-Season

Systems the high pressure gauge fitting is located on the

muffler and the low pressure gauge fitting is on the POA

Valve.

The Chevy n All-Weather System compressor con-

nector assembly is similar to the Universal System

connector assembly described above except that the

muffler extends straight out from the connector and

is not bracket mounted to the compressor.

Universal and Chevy II All-Weather System

1.
Install Gauge Adapter (J-5420 or J-9459) onto the

high and low pressure hoses of the gauge set.

2.
With the engine stopped, remove the caps from the

cored valve gauge, connectors on the compressor

fittings block.

3.
Connect the gauge lines with adapters to the threaded

connectors on the compressor fittings block.

Four-Season and Comfortron Systems

Installation of the gauge set onto the Four-Season and

Comfortron systems is accomplished in the same manner

as outlined above except that system performance checks

must be performed with the low pressure hose line and

adapter attached to the fitting on the POA valve. Charging

procedures should be performed with the high pressure

gauge line connected to the high pressure gauge fitting

located on the outlet line muffler and the low pressure

gauge line attached to the POA fitting.

CAUTION: When removing gauge lines from

the compressor fittings block be sure to remove

the adapters from the fittings rather than the

gauge lines from the adapters.

PERFORMANCE TEST

This test may be conducted to determine if the system

is performing in a satisfactory manner and should be

used as a guide by the serviceman in diagnosing trouble

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-33

within the system. The following fixed conditions must be

adhered to in order to make it possible to compare the

performance of the system being tested with the stan-

dards below:

1.
Doors and windows closed. (Car inside or in shade.)

2.
Hood up and engine exhaust suitably ventilated.

3.
Vehicle in NEUTRAL with engine running at 2000

rpm.

4.
Air Conditioning controls set for -

• Maximum cooling.

• High blower speed.

5.
TEMP knob and AIR knob set for full recirculating

air. On Comfortron systems* move the control lever

to REAR and pull the white vacuum hose from the

transducer. Plug the hose. An alternate method is to

install the J-22368 Tester (described later in this

section) and operate it on MANUAL control to main-

tain maximum cooling and blower speed.

6. Gauge set installed.

7.
System settled out (run-in approximately
10
minutes).

8. A thermometer placed in front of vehicle grille and

another in the right hand diffuser outlet.

PERFORMANCE DATA

The following Performance Data define normal opera-

tion of the system under the above conditions. Relative

humidity does not appear in the tables because after

running the prescribed length of time on recirculated air

and maximum cooling, the relative humidity of the air

passing over the evaporator core will remain at ap-

proximately 35% to 40% regardless of the ambient

temperature or humidity.

Should excessive head pressures be encountered at

higher ambient temperatures, an 18" fan placed in front

of the vehicle and blowing into the condenser will provide

the extra circulation of air needed to bring the pressures

to within the limits specified.

NOTE: Higher temperatures and pressures will

occur at higher ambient temperatures, fti areas

of high humidity it is possible to have ther-

mometer and gauge readings approach but not

reach the figures listed in the performance

tables and still have a satisfactory operating

unit. However, it is important to remember that

low pressure has a direct relationship to nozzle

outlet temperature. If pressure is too low, ice

will gradually form on the evaporator fins, re-

stricting airflow into the passenger area and

resulting in insufficient or no cooling.

Four-Season and Comfortron System

Chevrolet and Camaro
Chevelle

(Refrigerant
Charge
=

Temperature
of Air

Entering Condenser

Engine rpm

Compressor

Head Pressure

Evaporator Pressure

at POA

Discharge Air Temp,

at Right Hand Outlet
3
Lbs. -

70°

145-

155

38-

41
80°

170-

180
12 02

90°
.)

100°

2000

205-

215

29.5 -

39-

42
41-

43
255-

265

30.5

42-

45
110°

260-

270

psi

43-

46
120°

295-

305

45-

48
(Refrigerant Charge =

Temperature of

Air Entering

Condenser

Engine rpm

Compressor Head

Pressure

Evaporator
Pressure

at
POA

Discharge Air

Temp, at Right

Hand Outlet
3 Lbs. -

70°

150

160

37-

40
80°

175

185
12 Oz.)

90° 100°

2000

210 250

220 260

29.5 - 30.5

37-

40
38-
39-

41 42
110°

280

290

psi

40-

44
120°

290

300

41-

45

Corvette

(Refrigerant Charge =

Temp, of Air

Entering Condenser

Engine rpm

Compressor

Head Pressure

Evaporator
Pressure

at
POA

Outlet
Air

Temperature

(at Right
Outlet)
3
Lbs.

70°

150-

170

38-

40
- 4 Oz.)

80°

175-

195

29

38-

40
90°

2000

200-

200
100°

i*pm

240-

260
110°

285-

300

5-
30.5 psi

40-

42
41-

43
43-

45
120°

325-

335

45-

47

Alt Weather System

Chevy II

(Refrigerant
Charge
=

Grille Air

Temperature

Engine rpm

Compressor Head

Pressure

Compressor Suction

Pressure**

Discharge Air Temp,

at R/H Outlet**
2-1/2 Lbs.)

70°

120-

140

13

32-

37
80°

150-

160

14
CO
OO
CO
CO
90°
100°

1500

175-

185

15

35-

40
220-

230

15

36-

41
110°

240-

250

19

37-

42
120°

265-

275

19

38-

43

**When Compressor Clutch Releases

COMFORTRON SYSTEM OPERATIONAL TEST

This test, designed as a quick check of total system

operation, must be made with the engine operating at

minimum of 2000 rpm and coolant warm. Wait several

seconds between operations to allow the system to move

through its sequence of operation and arrive at the pre-

scribed mode of operation.

1.
With control lever in the OFF position, and Tem-

perature Dial at 65°F.

a. System is turned OFF, there is no air flow from

any of outlets.

2.
Control lever in HI Front and Temperature Dial set

at65°F.

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-34

a. Blower comes on High speed.

b.
Cold air comes from A/C outlets.

3.
Rotate Temperature Dial to 85°F.

a. Blower speed will decrease to Low speed then

increase to Medium or High.

b.
Air temperature changes from Cold to Hot and

comes out heater outlet.

4.
Move control lever to LOW Front, with Temperature

Dial at 85°F. Blower operates at Low and Medium

speeds.

5.
Move control lever to Rear, set Temperature Dial

at 65°F.

a. Blower goes to High speed and maintains high

air flow.

b.
All air comes from A/C outlets.

6. Move control lever to DE-FOG.

a. Blower is on Medium or High Speeds.

b.
Air comes from Defroster and Heater Outlets.

7.
Move control lever to DE-ICE.

a. Blower is on High Speed.

b.
Air temperature goes to warm and most of air

comes from defroster nozzle, with small amount

of air coming from heater outlet.

c. Outside air door is open - (door valve is closed

to car body).

8. Move control lever to REAR (dial at 65°). Outside

air door moves outboard. (Door valve is open to

car body).

CHEVROLET COMFORTRON TESTER

The J-22368 Automatic Temperature Control Tester

when in AUTOMATIC position, may be used to perform
Comfortron system checks without disturbing normal car

operation.

Under MANUAL control tester allows the operator to

set and hold a predetermined blower speed
and.
temper-

ature. The tester can also be used to measure external

system voltages by using the probe.

To Install the Tester

1.
Remove the three-terminal male connector from the

Amplifier on the Comfortron control head.

2.
Plug this connector into the three terminal female

connector (with yellow wire)
on
the Tester.

3.
Plug the remaining three-terminal male connector

on the Tester into the Amplifier on the control head.

4.
Attach the black ground lead to any good ground

point available in the car.

5.
Remove the large vacuum hose from Transducer and

connect it to the Tester vacuum hose nipple.

6. Connect the Tester vacuum hose (short hose) to the

Transducer.

Quick Test Procedure

With the J-22368 Tester installed as outlined above,

the following quick checks may be made to pinpoint

the cause of system malfunctions. This quick check

procedure is reproduced on the "swing out" plastic

instruction card attached to the back of the Tester.

Before performing the checking procedure, start the

engine and allow to run on fast idle until operating

temperature is reached. Then set the dash control lever

to HI-FRONT position and the dash control Temperature

Dial to 75° and proceed with the following steps:

Step

1

2

3

4

5A

5B
Tester Settings

Rocker

Switch

Manual

Manual.

Manual

Manual

Manual

Auto-

matic
Voltage

Source

Sensor

Amplifier

or

Control

Cal.

Trans-

ducer

Amplifier

or

Control

Cal.

Amplifier

or

Control

Cal.
Manual

Control

150

150

a. Max.

Heat*

b.
Max.

Cold*

a. Max.

Cold*

b.
Max.

Heat*

Set to

150 for

Comfortron

System

Same as 5A.

Allow 5 min.

for system

to stabilize

with doors

and windows

closed.
Tester Should

Indicate:

Battery Voltage

Battery Voltage

0-4 Volts

8 Volts Min.

8 Volts Min.

0-3 in. Vac.

0-4 Volts

9 in. Min. Vac.

6.5 Volts

5.5 to 7.5 Volts
To Correct Abnormal Indication:

Check fuse and wiring.

Check for open in sensor circuit.

See Service Manual:

Malfunctioning Amplifier or Temperature

Dial.

Check for open or bad ground in trans-

ducer circuit or replace transducer.

Rotate car temperature dial until meter

reads 6.5 volts. Car temperature should

'•- indicate 75°. If not, see temperature

calibration which follows.

After 5 minutes of operation check for

defective sensor.

•This setting should result in HIGH blower speed. Refer to shop manual for further operational checks.

CHEVROLET CHASSIS SERVICE MANUAL