fuel consumption CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

SECTION 6

ENGINE

CONTENTS
OF
THIS SECTION

Page

Engine Tune Up
6-1
Torque Sequence

Engine Mechanical
(In
Line)
6-12
Special Tools
. .

Engine Mechanical (V8)
6-24
Page

6-39

6-40

ENGINE TUNE UP

INDEX

Page

General Description
. 6-1

Mechanical Checks and Adjustments
6-1

Spark Plug Removal
6-1

Test Compression
6-1

Service and Install Spark Plugs
6-2

Service Ignition System
6-3

Service Battery
and
Battery Cables
6-5

Service Delcotron
and
Regulator
6-5

Service
Fan
Belt
6-5

Service Manifold Heat Valve
6-5

Tighten Manifold
6-5

Service Fuel Lines
and
Fuel Filter ..........
6-6

Service Cooling System
6-6

Check and Adjust Accelerator Linkage
6-6

Service Crankcase Ventilation
6-6

Service
Air
Injection Reactor System
6-6

Choke Adjustment
6-7
Page

Instrument Cheek-Out
6-7

Instrument Hook-Up.
. 6*7

Check and Adjust Dwell
6-7

Check Dwell Variation
6-7

Check and Adjust Timing
6-8

Adjust Idle Speed
and
Mixture
6-8

Additional Checks and Adjustments
. 6-8

Testing Crankcase Ventilation Valve
. 6-8

Testing Cranking Voltage
6-8

Cylinder Balance Test
. 6-8

Battery
6-8

Ignition
; 6-8

Carburetor
6-11

Fuel Pump
6-11

Cooling System
. 6-11

Cylinder Head Torque and Valve Adjustment
..... 6-11

GENERAL DESCRIPTION

The engine tune up
is
important
to the
modern automo-

tive engine with
its
vastly improved power and perform-

ance.
The
higher compression ratios, improved electri-

cal systems
and
other advances
in
design, make today1 s

engines more sensitive
and
have
a
decided effect
on

power, performance and fuel consumption.

It
is
seldom advisable
to
attempt
a
tune up
by
correc-

tion
of one or two
items only. Time will normally
be

saved
and
more lasting results assured
if the
technician

will follow
a
definite
and
thorough procedure
of
analysis

and correction
of all
items affecting power, performance

and economy.

The tune
up
will
be
performed
in
two parts.
The
first

part will consist
of
visual and mechanical checks and
ad-

justments;
the
second part will consist
of
an instrument

checkout that
can be
performed with
any one of the
units
of service equipment available
for
this purpose. Always

follow
the
instructions provided
by the
manufacturer
of

the particular equipment
to be
used.

Additional checks
and
adjustments
are
included
in the

latter part
of
this section
for use as
required. Many
of

these operations
can be
used
to
isolate and correct trou-

ble located during
the
tune up. Where conditions
are
UB-

covered requiring major corrective action, refer
to the

appropriate section
of
this manual
or the
Passenger

Chassis Overhaul Manual
for
detailed service informa-

tion.

Typical illustrations
and
procedures
are
used except

where specific illustrations
or
procedures
are
necessary

to clarify
the
operation. Illustrations showing bench
op-

erations
are
used
for
clarification however
all
operations

can
be
performed
on the
vehicle.

MECHANICAL CHECKS
AND
ADJUSTMENTS

Spark Plug Removal

Remove any foreign matter from around spark plugs
by

blowing
out
with compressed
air,
then disconnect wires

and remove plugs.

Test Compression
(Fig. 1)

The compression check
is
important because
an
engine

with
low or
uneven compression cannot
be
tuned success-
fully.
It is
essential that improper compression
be cor-

rected before proceeding with
the
engine tune
up.

1.
Remove
air
cleaner
and
block throttle
and
choke
in

wide open position.

2.
Hook
up
starter remote control cable
and
insert

compression gauge firmly
in
spark plug port.

CAUTION: Whenever
the
engine
is
cranked

CHEVROLET
C*
IS SERVICE MANUAL