torque CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

HEATER AND AIR CONDITIONING 1A-32

5.
Check hose clamp connections. If clamp screw torque

is less than 10 lb. in., retighten to 20-25 lb. in. Do

not tighten to new hose specifications or hose leak-

age may occur.

6. If there is evidence of an oil leak, check the com-

pressor to see that the oil charge is satisfactory.

7.
Check the system controls for proper operation.

6000 MILE INSPECTION

1.
Check unit for any indication of a refrigerant leak.

2.
If there is an indication of an oil leak, check the

compressor proper oil charge.

3.
Check sight glass for proper charge of Refrigerant-

12.

4.
Tighten the compressor brace and support bolts and

check the belt tension.

5.
Check hose clamp connections as in step 5 above.

6. Check thermostatic switch setting (Universal and

All-Weather Systems.)

PERIODIC SERVICE

• Inspect condenser regularly to be sure that it is not

plugged with leaves or other foreign material.

Fig.
46—Compressor Connector Block—Typical
• Check evaporator drain tubes regularly for dirt or

restrictions.

• At least once a year, check the system for proper

refrigerant charge and the flexible hoses for brittle-

ness,
wear or leaks.

• Every 6000 miles check sight glass for low refriger-

ant level.

• Check belt tension regularly.

• Every week - during winter months or other periods

when the system is not being operated regularly- run

the system, set for maximum cooling, for 10 or 15

minutes to insure proper lubrication of seals and

moving parts.

INSTALLING GAUGE SET TO CHECK

SYSTEM OPERATION

Compressor Suction and Discharge Connector

Compressor connector assemblies used on all vehicles

are of the same basic design consisting of the inlet

(suction) and outlet (discharge) connections, gauge fittings

and muffler and, in general, the assemblies differ only in

the location of the gauge fittings.

On Universal and Four-Season Systems the outlet line

extends along side of and toward the front of the com-

pressor and the muffler in the line is bracket mounted to

the compressor body. In all Universal Systems the gauge

fittings for both low and high pressure sides of the sys-

tem are located in the connector body. On Four-Season

Systems the high pressure gauge fitting is located on the

muffler and the low pressure gauge fitting is on the POA

Valve.

The Chevy n All-Weather System compressor con-

nector assembly is similar to the Universal System

connector assembly described above except that the

muffler extends straight out from the connector and

is not bracket mounted to the compressor.

Universal and Chevy II All-Weather System

1.
Install Gauge Adapter (J-5420 or J-9459) onto the

high and low pressure hoses of the gauge set.

2.
With the engine stopped, remove the caps from the

cored valve gauge, connectors on the compressor

fittings block.

3.
Connect the gauge lines with adapters to the threaded

connectors on the compressor fittings block.

Four-Season and Comfortron Systems

Installation of the gauge set onto the Four-Season and

Comfortron systems is accomplished in the same manner

as outlined above except that system performance checks

must be performed with the low pressure hose line and

adapter attached to the fitting on the POA valve. Charging

procedures should be performed with the high pressure

gauge line connected to the high pressure gauge fitting

located on the outlet line muffler and the low pressure

gauge line attached to the POA fitting.

CAUTION: When removing gauge lines from

the compressor fittings block be sure to remove

the adapters from the fittings rather than the

gauge lines from the adapters.

PERFORMANCE TEST

This test may be conducted to determine if the system

is performing in a satisfactory manner and should be

used as a guide by the serviceman in diagnosing trouble

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-45

• A very badly leaking compressor seal.

• Collision damage to the system components.

As a quick check on compressor oil charge, with the

engine off, carefully crack open the oil drain plug on the

bottom of the compressor. If oil comes out, the com-

pressor has the required amount of oil To further check

the compressor oil charge, should the above test show

insufficient oil, it is necessary to remove the compressor

from the vehicle, drain and measure the oil.

Checking Compressor Oil Charge

1.
Run the system for 10 minutes at 500-600 engine

rpm with controls set for maximum cooling and

high blower speed.

2.
Turn off engine, discharge the system, remove

compressor from vehicle, place it in a horizontal

position with the drain plug downward. Remove the

drain plug and, tipping the compressor back and

forth and rotating the compressor shaft, drain the

oil into a clean container, measure and discard the

oiL

3.
a. If the quantity drained was 4 fluid oz. or more,

add the same amount of new refrigerant oil to

the replacement compressor.

b.
If the quantity drained was less than 4 fluid oz.,

add 6 fluid oz. of new refrigeration oil to the

replacement compressor.

c. If a new service compressor is being installed,

drain all oil from it and replace only the amount

specified in Steps 3a and 3b above.

d. If a field repaired compressor is being installed,

add an additional 1 fluid oz. to the compressor.

4.
In the event that it is not possible to idle the com-

pressor as outlined in Step 1 to effect oil return to

it, proceed as follows:

a. Remove the compressor, drain, measure and

discard the oil.

b.
If the amount drained is more than 1-1/2 fluid

oz.
and the system shows no signs of a major

leak, add the same amount to the replacement

compressor.

c. If the amount drained is less than 1-1/2 fluid oz.

and the system appears to have lost an excessive

amount of oil add 6 fluid oz. of clean refrigeration

oil to replacement compressor, 7 fluid oz. to a

repaired compressor.

If the oil contains chips or other foreign ma-

terial, replace the receiver-dehydrator and flush
or replace all component parts as necessary. Add

the full specified volume of new refrigeration oil

to the system.

5.
Add additional oil in the following amounts for any

system components being replaced.

Evaporator 3 fluid oz.

Condenser . . . . ... . . . . . . 1 fluid oz.

Receiver-Dehydrator ....... 1 fluid oz.

NOTE: When adding oil to the compressor, it

will be necessary to tilt the rear end of the

compressor up so that the oil will not run out

of the suction and discharge ports. Do not set

the compressor on the shaft end.

Adding Oil to the System

The system should be completely assembled and un-

charged before adding oil. Use only uncontaminated

refrigerant oil (525 viscosity) and add as follows:

1.
Connect the low pressure line from the gauge set

to the low pressure gauge fitting on the P.O.A.

valve (Four-Season) or low pressure fitting on the

compressor connector Mock (Universal System).

2.
Connect the high pressure line from the charging

station gauge set to the compressor muffler or high

pressure side of the connector block.

3.
Disconnect the high pressure line from the gauge set,

make certain that the line is clean, and place the

end in a graduated container.

4.
Pour enough refrigerant oil into the container so

that the required volume may be drawn into the

system by the high pressure hose.

5.
Close the high pressure valve at the gauge set,

and open the low pressure valve.

6. Operate the vacuum pump to drop the pressure within

the system and cause atmospheric pressure to force

oil through the high pressure line into the system.

When the oil level has dropped the required volume,

pull the line out of the oil container and continue

vacuum pump operation to force the oil contained

in the line into the system.

7.
Shut off the vacuum pump and connect ttye high

pressure line to the gauge set. Open the high

pressure valve and evacuate the system through

the high and low pressure sides of the system.

Complete the charging operation as outlined in Step

10 under "Evacuating and Charging System".

COMPONENT REPLACEMENT AND MINOR REPAIRS

REFRIGERANT LINE CONNECTIONS

"O"
Rings

Always replace the "O" ring when a connection has

been opened. When replacing the "O" ring, first dip it

in refrigeration oil. Always use a backing wrench on

"O"
ring fittings to prevent the pipe from twisting and

damaging the "O" ring. Do not overtighten. Correct

torque specifications are as follows:
Metal

Tube

O.D.

1/4

3/8

1/2

5/8

3/4
Thread and

Fitting

Size

7/16

5/8

3/4

7/8

1-1/16
Steel

Tubing

Torque*

13

33

33

33

33
Alum.

Tubing

Torque*

6

12

12

20

25

* Pound Feet

CHEVROLET CHASSIS SERVICE

HEATER AND AIR CONDITIONING 1A-46

MAKE ANGULAR CUT

FOR HOSE REMOVAL

LOCATING

BEAD

SEALING

BEADS
LOCATING

BEAD
not to nick or score the sealing beads when

cutting off the hose. Cutting the hose lengthwise

may result in this problem.

Fig.
58—Hose Clamp Connections

NOTE:
Where steel to aluminum connections

are being made, use torque for aluminum tubing.

Hose Clamps (Fig. 58)

When hose clamp connections are encountered special

procedures are necessary for both installation and

removal.

Installation

1.
Coat tube and hose with refrigeration oil.

2.
Carefully insert hose over the three beads on the

fitting and down as far as the fourth, or locating,

bead. Hose must butt against this fourth bead.

CAUTION: Use no sealer of any kind.

3.
Install clamps on hose, hooking the locating arms

over the cut end of the hose.

4.
Tighten the hose clamp screw to 35-42 lb. in.

(except Corvette) 30-38 lb. in. (Corvette). DO NOT

RETORQUE.

Removal

1.
Carefully, with a sharp knife, make an angle cut in

the hose as shown in Figure 58. This should loosen

the hose so that it may be worked off the fitting.

2.
Cut off slit end of hose when reinstalling. Reinstall

as described above.

CAUTION: Use only approved refrigeration

hose. Never use heater hose. Use extreme care
REPAIR OF REFRIGERANT LEAKS

Any refrigerant leaks found in the system should be

repaired in the manner given below:

Leaks at "O" Ring Connection

1.
Check the torque on the fitting and, if too loose,

tighten to the proper torque. Always use a backing

wrench to prevent twisting and damage to the "O"

ring. Do not overtighten. Again leak test the joint.

2.
If the leak is still present, discharge the refrigerant

from the system as described under "Evacuating

and Charging Procedures."

3.
Inspect the ''O" ring and the fitting and replace if

damaged in any way. Coat the "O". ring before re-

installed with refrigerati6n oil and install carefully.

4.
Retorque the fitting, using a backing wrench, and

then add 1/2 to 1 lb. of R-12 to the system and

recheck for leaks.

CAUTION: Do not operate the system with this

small refrigerant charge.

5. Purge the system, thus removing the 1/2 to 1 lb.

installed in Step 4 above.

6. Evacuate and charge the system.

Leaks at Hose Clamp Connection

1.
Check the tightness of the clamp itself and tighten

if necessary. Recheck for leak.

2.
If leak has not been corrected discharge the system

and loosen clamp and remove hose from connection.

Inspect condition of hose and connector. Replace

scored or damaged parts.

3.
Dip end of new hose in refrigerant oil and carefully

reinstall over connector. Never push end of hose

beyond the locating bead. Properly torque the clamp.

4.
Recheck the system for leaks by installing 1/2 to 1

lb.
of R-12 into the system. Do not run compressor.

5. Purge. the system, thus removing the 1/2 to 1 lb.

installed in Step 4 above.

6. Evacuate and charge the system.

Compressor Leaks

If leaks are located around the compressor shaft seal

or shell, replacement of necessary seals should be made

as outlined under "Compressor" in the Chassis Overhaul

Shop Manual.

REFRIGERANT HOSE FAILURE

After a leak or rupture has occurred in a refrigerant

hose, or if a fitting has loosened and caused a consider-

able loss of refrigerant and oil, the entire system should

be flushed and recharged after repairs have been made.

Ji the system has been open to atmosphere for any pro-

longed period of time the receiver-dehydrator should be

replaced.

PREPARING SYSTEM FOR REPLACEMENT

OF COMPONENT PARTS

Air conditioning, like many other things, is farily

simple to service once it is understood. However, there

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-48

Fig.
60-Condenser Mounting (Chevy II)

2.
Remove the bumper, bumper filler panel, grille,

grille support, hood lock catch support and catch as

described in Section 11, "Chassis Sheet Metal".

3.
Disconnect connectors at condenser inlet and outlet

tubes and remove screws attaching refrigerant line

holding clips to the condenser baffle.

4.
Remove bolts attaching condenser through radiator

' support and slide condenser to the left and out of

vehicle.

5. Reverse these steps to reinstall new condenser.

6. Evacuate and charge the system. Add one fluid oz.

of refrigerant oil after installing a new condenser.

Corvette

Replacement (Production Engine)

1.
Remove the hood from the car, first scribing the

hinge attachment location.

2.
Purge the system of refrigerant.

Fig.
61—Condenser Mounting (Cdrnaro)
Fig.
62—Condenser Mounting (Corvette)

3.
Disconnect the inlet line connection at the condenser

inlet and the outlet line at the receiver-dehydrator.

Cap the receiver-dehydrator immediately.

4.
Remove the screws attaching the condenser to the

radiator support and carefully lift the unit from the

car.

5. Remove the receiver-dehydrator from the old con-

denser and install it, using a new "O" ring, on the

new condenser.

6. Set new condenser in place on the radiator support

and install the attaching screws, torquing them to

20 lbs. ft.

7. Make the inlet and outlet connections, using new

"O"
rings, and torque 13 lbs. ft.

8. Evacuate, charge and check the system. Add one

fluid oz. of refrigerant oil after installing a new

condenser.

Replacement (Optional Engine)

Replacement procedure remains much the same for the

installation supplied with the optional engine except for

the location of the receiver-dehydrator. Follow the steps

given above except that the outlet line must be removed

at the receiver outlet. (See Figure 64.)

RECEIVER-DEHYDRATOR

The receiver-dehydrator should be replaced if it has

been damaged through an accident or if it leaks or be-

comes restricted or clogged. Do not attempt to repair

the receiver-dehydrator.

The receiver-dehydrator is merely a moisture collect-

ing device and a refrigerant storage area and is the least

likely component of the system to cause a malfunction.

If at any time when examining the compressor oil,

moisture is found or there is an indication of moisture

at the expansion valve needle, the receiver-dehydrator

should be replaced as follows (fig. 63):

NOTE:
If the receiver-dehydrator is to be re-

used, cap the inlet and outlet connections

immediately. When installing a receiver-

dehydrator, do not uncap the connections until

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-49

CHEVROLET

CHEVELLE

CHEVY II

CAMARO
the last possible moment. Be certain that the

direction of flow is correct before connecting

the pipes.

Chevrolet, Chevelle, Chevy II, and Camaro

Replacement

1.
Remove the receiver inlet and outlet connections and

the two receiver to fender skirt attaching screws.

2.
Carefully remove the receiver-dehydrator from the

vehicle.

3.
Replace the new receiver~dehydrator assembly in

the vehicle and install all attaching screws and re-

frigerant lines.

4.
Add one fluid oz. refrigerant oil, evacuate and charge

the system.

Corvette

Replacement

1.
Purge the system of refrigerant.

2.
Disconnect the "O" ring inlet

hose clamp outlet connection

openings.

3.
Remove the receiver-dehydrator to radiator support

bracket screws (production engine) or receiver-

dehydrator to condenser bracket screws (optional

engine) and remove the unit from the car.

4.
Install the new receiver-dehydrator applying 30 in.

lbs.
torque to the attaching screws.
connection and the

and tape the hose

NOTE:
Do not uncap the new receiver-

dehydrator until the last instant before

installation.

5.

2.

3.

Fig.
63—
Receiver-Dehydrator Mounting (Chevrolet,

Chevelle/ Chevy II, Camaro)
Connect the high pressure lines at the inlet (use a

new "O" ring and torque connection to 13 ft. lbs.)

and outlet (torque screw to 25 in. lbs.).

6. Add one fluid oz. refrigerant oil, evacuate, charge

and check the system.

Sight Glass Replacement-All Vehicles

If damage to the sight glass should occur, a new sight

glass kit should be installed. The kit contains the sight

glass,
seal and retainer. (See Figure 65.)

1.
Purge system.

Remove the sight glass retainer nut using a screw

driver and remove old glass and seal.

Install the new glass and seal and retainer nut, being

careful not to turn the nut past the face of the hous-

ing. To do so may damage the "O" ring seal.

4.
Evacuate and recharge the system.

EVAPORATOR

Chevrolet and Camaro Four-Season System

The evaporator and blower case assembly is designed

so that the core may be removed without the need for

removing the entire unit from the vehicle. Instead,

only the side cover must be removed.

Removal and Installation of Entire Assembly

1.
Remove the inlet line at the expansion valve and the

suction throttling valve outlet connection.

2.
Remove the electrical connector from the blower

motor.

CHEVROLET CHASSIS SERVICE MANUAL

CORVETTE BODY 1B-27

CUT OFF PAINTED

PORTION OF CARTRIDGE NOZZLE

ALONG EDGE-OF PAINT LINE

ADHESIVE CAULKING

MATERIAL

Fig.
60—Applying Caulking Material to Glass

GARNISH MOLDINGS PLUS HEADLINER-

19437 MODEL

Figure 64 illustrates installation details of garnish

moldings and headlining.

Headlining is not cemented in place.

Removal of dome lamp and garnish moldings is

necessary.
J-NUT

FILLER PANEL

BODY REAR

Fig.
61—Installing Rear Glass
Fig.
62—Gas Tank Door and Rear Trim Plate

SEATS

Removal

1.
Remove bolt retaining each forward support to floor.

2.
Fold seat back forward.

3.
Loosen two bolts retaining each seat hold-down

bracket.

4.
Move seat forward and out of brackets.

Adjustments

Height of seats is adjustable at both front and rear by

means of shims or washers.

Angle of seat backrest may be changed by adjusting

stops located on lower edge of seat back.

BODY MOUNTING

Figure 65 illustrates underbody attachment-to-frame

body mounting brackets. Shims which are shown on

rear crossmember are cemented in place.

The torque of all body mounting bolts should be checked

periodically as an aid to preventing annoying squeaks

and rattles. AH bolts shown in Figure 65 should be

torqued to 45 lbs. ft.

BODY REPAIRS

GENERAL INSTRUCTIONS

The following gives information necessary for repair

of collision damage and performance of general main-

tenance on both the 19437 and 19467 Corvette bodies.

Included here is information dealing with availability of

repair panels, general installation procedures for in-

staUing panels and repairing damage to the body.

Repair of fiber glass reinforced plastic bodies is a

relatively easy matter if a few simple precautions are

observed.

In cases where welding must be done on steel parts

which are stiU installed on body, do not allow flame or

direct welding heat to come into direct contact with

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-3

by means of a lower control arm inner pivot cam; on the

Chevelle, Camaro and Corvette by means of upper control

arm inner support shaft shims.

Caster angle is adjusted, on the Chevrolet and Chevy n

by means of a strut rod which runs from the lower con-

trol arm forward to a frame brace; on the Chevelle,
Camaro and Corvette by means of upper control arm

inner support shaft shims.

A stabilizer bar is used on all Chevelle and Corvette

models. Chevrolet Impalas, station wagons and V-8

engine equipped models are fitted with the stabilizer bar.

UPPER CONTROL ARM

STABILIZER

SPRING
LOWER CONTROL ARM

STEERING KNUCKLE

Fig.
3 - Front Suspension - Corvette

MAINTENANCE AND ADJUSTMENTS

Maintenance intervals recommended for lubrication of

front suspension components have been fully covered in

Section 0 of this manual. Only actual adjustment proce-

dures will be covered here.

NOTE:
Unless otherwise indicated all proce-

dures will apply to all five vehicles covered in

this manual.

FRONT WHEEL BEARING ADJUSTMENT

Proper front wheel bearing adjustment has a definite

bearing on the safe operation of a vehicle. Improperly

adjusted front wheel bearings will result in a lack of

steering stability causing wheel wander, shimmy and ex-

cessive tire wear. Very accurate adjustment is possible

because the spindles are drilled both vertically and hori-

zontally and the adjusting nuts are slotted in all six sides.

NOTE:
Wheel bearings should not
be.
repacked

or adjusted as a part of "New Car Conditioning".
1.
With wheel raised, remove hub cap and dust cap and

then remove the cotter pin from the end of the

spindle.

2.
While rotating wheel, tighten spindle nut to 12 lbs. ft

torque.

3.
Back off adjusting nut one flat and insert cotter pin.

If slot and pin hole do not line up, back off the adjust-

ing nut an additional 1/2 flat or less as required to

insert cotter pin.

4.
Spin the wheel to check that it rolls freely and then

lock the cotter pin by spreading the end and bending

it around.

NOTE:
Bearings should have zero preload and

.001"
to .008" end movement when properly ad-

justed on Chevrolet, Chevelle, Camaro and Cor-

vette; .000" to .004" on Chevy H.

5.
Install dust cap, hub cap or wheel disc and lower

wheel.

6. Perform the same operation on each front wheel.

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-10

CHEVROLET, CHEVELLE, CAMARO AND CORVETTE (TYPICAL)
CHEVY H

Fig.
14- Shock Absorber

NOTE:
If necessary, tighten one more notch to

insert cotter pins.

3.
Place brake backing plate and wheel cylinder in posi*-

tion on steering knuckle and insert anchor pin.

4.
Place steering arm in position on back of steering

knuckle and insert two bolts through backing plate,

steering knuckle and steering arm. Install locknuts

and tighten. (See Specifications.)

5. Torque brake anchor pin (See Specifications).

6. Install brake shoes, except Corvette. (See Section 5.)

7. Install wheel hub, brake drum (or, on Corvette--

brake caliper and disc and hub assembly), wheel and

tire assembly over spindle.

8. Insert outer wheel bearing race and roller assembly,

washer and nut. Adjust front wheel bearing as shown

under Maintenance and Adjustments in this section.

Install new cotter pin, dust cap and hub cap.

9. Lower vehicle, recheck and readjust wheel alignment

where necessary.

SHOCK ABSORBER

Chevrolet, Chevelle, Comoro and Corvette (Fig. 14)

Removal

1.
With an open end wrench hold the shock absorber

upper stem from turning, and then remove the upper

stem retaining nut, retainer and rubber grommet.

2.
Remove the two bolts retaining the lower shock ab-

sorber pivot to the lower control arm and pull the

shock absorber assembly out from the bottom.

Installation

1.
With the retainer and rubber grommet in place over

the upper stem, install the shock abosrber (fully ex-
tended) up through the lower control arm and spring

so that the upper stem passes through the mounting

hole in the upper support arm.

2.
Install the rubber grommet, retainer' and attaching

nut over the shock absorber upper stem.

3.
With an open end wrench, hold the upper stem

from turning and tighten the retaining nut. (See

Specifications.)

4.
Install the two bolts attaching the shock abosrber

lower pivot to the lower control arm and tighten.

(See Specifications.)

Fig.
15 - Upper Control Arm Support Installed - Chevy II

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-11

Chevy II (Fig. 14)

Removal

1.
While vehicle weight is still on front wheels, position

support between upper control arm and frame side

rail (fig. 15).

NOTE: Bight side control arm support bracket

is illustrated in Figure 15. For left side, angled

support should be welded to reverse side of

plate.

2.
Raise vehicle and remove wheel and tire.

3.
Disconnect lower shock absorber mounting nuts, lock

washers and rubber washers from lower spring seat.

4.
Remove shock absorber upper mounting bracket

bolts.
Lift bracket and shock absorber assembly

from vehicle (fig. 16).

5.
Remove shock absorber from upper mounting bracket

and remove rubber bushings and washers.

Installation

1.
Assemble upper washer and rubber bushing to shock

absorber rod (refer to Figure 14).

2.
Assemble upper mounting bracket, bushing, washer

and nut to rod. Torque according to Specifications at

the end of this book.

3.
Install rubber washers to shock absorber lower seat

studs and insert shock absorber and upper bracket

assembly into shock absorber access hole, and posi-

tion to the lower spring seat. Install washers, nuts

and torque according to Specifications at the end of

this book.

NOTE: Shock absorber seat upper washers

must correctly pilot into spring seat.

4.
Install upper mounting bracket to spring tower and

torque nuts according to Specifications at the end of

this book.

STABILIZER BAR (FIG. 17)

Removal

1.
Raise vehicle and support both front wheels.

2.
Disconnect stabilizer bar from lower control arm.

Remove stabilizer bar brackets from the frame

(Chevrolet, Chevelle, Camaro and Corvette) or from

the front crossmember (Chevy n) and remove

stabilizer.
Fig.
16 - Removing Shock Absorber and Bracket - Chevy II

3.

Disconnect stabilizer link bolts, spacers and rubber

bushings from lower control arms.

4.
Inspect rubber stabilizer link bushings and Stabilizer

insulator bushings for aging. Replace if necessary.

Installation

1.
If new insulators
are necessary, coat stabilizer with

recommended rubber lubricant and slide frame bush-

ings into position.

2.
Insert stabilizer brackets over bushings and connect

to frame. Do not torque at this point. Connect sta-

bilizer ends to link bolts on lower control arms.

Torque bracket bolts and link nuts as shown in the

Specifications.

NOTE: Never get lubricant on outside of frame

stabilizer bar bushings or they may slip out of

brackets.

STRUT ROD (FIG. 18)

Chevrolet and Chevy II

Removal

1.
Raise vehicle to

clearance.
provide sufficient working

TYPICAL OF

CHEVROLET, CHEVELLE AND CAMARO
BRACKET LINK BOLT

CORVETTE
CHEVY H

Fig.
17- Stabilizer Bar

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-12

2.
Remove forward nut, retainer and rubber bushing

from front end of strut rod.

3.
Remove two nuts from strut rod to lower control arm

bolts and remove bolts and washers.

4.
Withdraw strut rod from bracket.

5. Remove remaining rubber bushing, retainer, sleeve

and nut from strut rod.

6. Inspect rubber bushings for aging and replace if

necessary. *•

Installation

1.
Screw rear nu$ on forward end of rod and position it

approximately 3/4" from end of threads. Install

rear retainer, sleeve and bushing on rod so raised

pilot diameter faces forward.

2.
Insert strut rod in bracket so pilot diameter on bush-

ing pilots in hole in bracket. Install forward bushing

on sleeve so raised pilot diameter faces rear to

enter hole in bracket, then install forward retainer

and nut on rod.

3.
Attach strut rod to top of lower control arm with two

bolts,
washers and nuts.

4.
Lower vehicle to floor, check caster and camber

angles and adjust where necessary. Torque nuts as

shown in Specifications.

FRONT SPRING

Chevrolet

Removal

1.
With an open end wrench hold the shock absorber

upper stem from turning, and then remove the upper

stem retaining nut, retainer and rubber grommet.
I IVi" rVi"i

\>. j ii

>
I

5'4

s

WOOD
BLOCK
USED

WITH
CHEVROLET
ONLY

Fig.
19
- Spring Removal Tools - Chevrolet, Chevelle and Comoro

2.
With the car supported by the frame so that the con-

trol arms hang free, remove the wheel and tire as-

sembly (replace one wheel nut to retain the brake

drum),
shock absorber, stabilizer bar to lower con-

trol arm link, strut rod to lower control arm attach-

ing, nuts, bolts and lock washers and tie rod end.

3.
Scribe the position of the inner pivot camber adjust-

ing cam bolt and then remove the nut, lock washer

and outer cam.

4.
Install a steel bar (fabricated as shown in Figure 19)

through the shock abosrber mounting hole in the

lower control arm so that the notch seats over the

bottom spring coil and the bar extends inboard and

under the inner bushing. Fit a 5" wood block (See

Figure 19) between the bar and the bushing as shown

in Figure 20.

5.
With suitable jack or hoist, lift up slightly on the end

of the bar to remove the tension from the inner pivot

cam bolt, which can then be removed.

Fig.
18-Strut Rod

Pig. 20 - Front Spring Removal - Chevrolet

CHEVROLET CHASSIS SERVICE MANUAL