check engine CHEVROLET CAMARO 1996 4.G User Guide

Downloaded from www.Manualslib.com manuals search engine Turn Signal and Lane Change Indicator
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the lever all the way up or down.
When the
turn is finished, the lever will return automatically.
An arrow on the instrument
panel will flash in the
direction
of the turn or
lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete
your lane change. The lever will return by
itself when you release it. As
you signal a turn
or a lane change, if the arrows don’t
flash but just stay on, a signal bulb may be burned out
and other drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident.
If the arrows don’t go on at all when you
signal a turn, check the fuse (see “Fuses and Circuit
Breakers” in the Index).
Headlamp High/Low Beam Changer
To change the headlamps
from low beam to high or
high to low, pull the turn
signal lever all the way
toward you.
Then release it.
When
the high beams
are on, this light on the
instrument panel also
will be
on.
2-44

Downloaded from www.Manualslib.com manuals search engine Power Remote Control Mirror (Option) Convex Outside Mirror
Your
passenger’s side mirror is convex. A convex
mirror’s surface
is curved so you can see more from the
driver’s seat.
A convex mirror can make things (like other
vehicles) look farther
away than they really are.
If you cut too sharply into the right lane, you
could hit a vehicle on
your right. Check your
inside mirror or glance over your shoulder
before changing lanes.
The power mirror control is on the driver’s door. To
adjust either mirror, turn the switch to left (L) or
right
(R). Then use the control to adjust the mirror.
The control only works when the ignition switch is in
the
RUN or ACC positions, or when RAP is present.
(See “Retained Accessory Power”
in the Index.)

Downloaded from www.Manualslib.com manuals search engine T-Top Sunshades
An improperly installed T-Top panel may fall
into or
fly off the vehicle. You or others could be
injured. After installing a T-Top panel, always
check that it is firmly attached by pushing up on
the underside of the panel.
Reverse the steps above to install the T-top panels.
When installing panels,
be sure to align weatherstrips
properly. Panels incorrectly installed may leak.
I NOTICE:
High pressure car washes may cause water to
enter your vehicle. Never spray water directly
at
the roof panel joints. This will cause leaks.
1. Start with the panel marked DRIVER FRONT.
Unlatch the driver’s side T-top, raise
it halfway and
close the latch handle.
2. With the top raised and resting on the center roof
rail, slide the flat edge of the sunshade panel (with
the vinyl side
to the glass) between the glass and
plastic trim, making
sure the edge marked DRIVER
FRONT is pointing to the front of the vehicle.
3 LA

Downloaded from www.Manualslib.com manuals search engine /'
3. Open the latch and close the T-top. Check to see if
there are any gaps showing. Unlatch the T-top and
adjust the sunshade as required.
4. Once the sunshade is installed properly, you can
stick the Velcro@ buttons
on the glass for a proper fit
every time
you install the sunshades. To do this, first
remove the T-top with the sunshade installed and
place it upside down on a table or bench. Take care
not to scratch the glass.
L
5. Pull the sunshade back a little and remove the
backing paper from the Velcro buttons. Push the
sunshade back into place, sticking the Velcro
to
the glass.
6. Install the T-top, close the latch and lock
the T-top. Repeat the above steps for the
passenger-side sunshade.
2-65

Downloaded from www.Manualslib.com manuals search engine Warning lights come on when there may be or is a
problem with one
of your vehicle’s functions. As you
will
see in the details on the next few pages, some
warning lights come on briefly when you start the
engine just
to let you know they’re working. If you are
familiar with this section, you should not be alarmed
when this happens.
Gages can indicate when there may be or is a problem
with one of your vehicle’s functions. Often gages and
warning lights work together
to let you know when
there’s a problem with your vehicle.
When
one of the warning lights comes on and stays on
when
you are driving, or when one of the gages shows
there may be
a problem, check the section that tells you
what
to do about it. Please follow this manual’s advice.
Waiting
to do repairs can be costly -- and even
dangerous.
So please get to know your warning lights
and gages. They’re a big help.
Safety Belt Reminder Light
When the key is turned to RUN or START, a tone will
come
on for about eight seconds to remind people to
fasten their safety belts, unless the driver’s safety belt is
already buckled.
~
The safety belt light will
also come on and stay
on until the driver’s belt
is buckled.
2-76

Downloaded from www.Manualslib.com manuals search engine Air Bag Readiness Light
There is an air bag readiness light on the instrument
panel, which shows AIR BAG. The system checks the
air bag’s electrical system for malfunctions. The light
tells you if there is an electrical problem. The system
check includes the air bag sensors, the air bag modules,
the wiring and the crash sensing and diagnostic module.
For more information on the air bag system, see “Air
Bag” in the Index.
AIR
BAG
You will see this light flash
for a few seconds when you
turn your ignition to
RUN
or START. Then the light
should go
out. This means
the system
is ready.
If the air bag readiness light doesn’t come on when you
start your vehicle, or stays on, or comes on when you
are driving, your air bag system may not work properly.
Have your vehicle serviced right away.
Voltmeter
You can read battery
voltage
on your voltmeter.
If it reads less than 11 volts
or more than
16 volts while
your engine is running, and
it stays there, you may
have a problem with the
electrical charging system.
Have it checked right away. Driving with the voltmeter
reading in
a warning zone could drain your battery.
If you idle your engine for a while, the voltmeter reading
might move into the low voltage zone (indicated by red
dots).
If the reading stays in the low voltage zone while you
are driving, you may have a problem with the electrical
charging system. Have it checked.
While the voltmeter
reads in
the low voltage zone, your battery may not be
able
to power certain electrical accessories, like ABS. (If
this happens, your ABS INOP light will come on. See
“Anti-Lock Brake System Warning Light” in this section.)
If you must drive a short distance with the voltmeter
reading in a warning zone,
turn off all your accessories,
including your air conditioning system and audio system.
2-77

Downloaded from www.Manualslib.com manuals search engine Low Coolant Light (VI3 Engine)
This warning light should
come on while you are
starting
your engine. If the
light doesn’t come on, have
it repaired.
Your Camaro
is equipped with a LOW COOLANT
indicator that is designed to detect when the coolant
level
drops below the set limit. If the low coolant level
sensor (on
the radiator) detects that the level drops while
the engine is running, the
LOW COOLANT indicator
will light and remain lit until the ignition switch is
turned to the
OFF position. Check the coolant level
and add coolant as needed. The
LOW COOLANT
light might stay on after filling
the radiator. Turn the ignition switch to the
OFF
position, then restart the engine to verify that the LOW
COOLANT light goes out. See “Engine Coolant” in
the Index.
1 NOTICE:
Driving with the LOW COOLANT light on could
cause your Chevrolet to overheat. See “Engine
Overheating” in the Index.
Your Chevrolet could
be damaged, and it wouldn’t be covered by
your warranty.
2-82

Downloaded from www.Manualslib.com manuals search engine Malfunction Indicator Lamp
(Service Engine Soon
Light)
Your Chevrolet is equipped
with a computer which
monitors operation
of the
SERVICE
fuel, ignition and emission
control systems.
This system is called OBD I1 (On-Board
Diagnostics-Second Generation) and is intended
to assure that emissions are at acceptable levels for
the life of the vehicle, helping to produce a cleaner
environment. (In Canada, OBD
I1 is replaced by
Enhanced Diagnostics.) The SERVICE ENGINE SOON
light comes on to indicate that there is a problem and
service is required. Malfunctions often will be indicated
by the system before any problem is apparent, which
may prevent more serious damage to your vehicle. This
system is also designed to assist your service technician
in correctly diagnosing any malfunction.
NOTICE:
If you keep driving your vehicle with this light
on, after a while, your emission controls may not
work as well, your fuel economy may not be as
good and your engine may not run as smoothly.
This could lead to costly repairs that may not be
covered by your warranty.
This light should come on, as a check to show you it is
working, when the ignition is
on and the engine is not
running. If the light doesn’t come on, have it repaired.
This light will
also come on during a malfunction in one
of two ways:
0
0
Light Flashing -- A misfire condition has been
detected. A misfire increases vehicle emissions and
may damage the emission control system on your
vehicle. Dealer or qualified service center diagnosis
and service is required.
Light On Steady -- An emission control system
malfunction has been detected on your vehicle.
Dealer or qualified service center diagnosis and
service may be required.
2-83

Downloaded from www.Manualslib.com manuals search engine Have you recently changed brands of fuel?
If
so, be sure to fuel your vehicle with quality fuel (see
“Fuel” in the Index). Poor fuel quality will cause your
engine not to run as efficiently as designed. You may
notice this as stalling after start-up, stalling when you
put the vehicle into gear, misfiring, hesitation on
acceleration or stumbling
on acceleration. (These
conditions may
go away once the engine is warmed up.)
This will be detected by the system and cause the light
to turn on.
If you experience this condition, change the fuel brand
you
use. It will require at least one full tank of the
proper fuel to turn the light
off.
If none of the above steps have made the light turn off,
have your dealer or qualified service center check the
vehicle. Your dealer has the proper test equipment and
diagnostic tools to fix any mechanical
or electrical
problems that may have developed.
Engine Oil Pressure Gage
5.7L LT1 Engine 3800 L36 Engine
This gage tells you if there could be a problem with your
engine oil pressure.
The engine oil pressure gage shows the engine oil
pressure in psi (pounds per square inch)
in the United
States, or kPa (kilopascals)
in Canada, when the engine
is running. Oil pressure should be
20 to 80 psi (140 to
550 kPa). On the 3.8L engine, the oil pressure should be
between
20 and 120 psi (140 to 827 kPa). It may vary
with engine speed, outside temperature and oil viscosity,
2-85

Downloaded from www.Manualslib.com manuals search engine but readings above the red area show the normal
operating range. Readings in the red area tell you that
the engine is low on oil,
or that you might have some
other oil problem. See “Engine Oil” in the Index.
-
Don’t keep d ling if the oil pressure is low. If
you do, your engine can become so hot that it
catches
fire. You or others could be burned.
Check your oil
as soon as possible and have your
vehicle serviced.
I NOTICE:
Damage to your engine from neglected oil
problems can be costly and is not covered by
your warranty.
Low Oil I.’
LOW OIL
This warning light should
come
on while you are
starting your engine.
If the
light doesn’t
come on, have
it repaired.
If the light stays on after starting your engine, your
engine oil level may be too
low. You may need to add
oil. See “Engine Oil” in the Index.
I NOTICE:
The oil level monitoring system only checks the
oil level when you are starting your engine. It
does not keep monitoring the level once the
engine is running.
Also, the oil level check only
works when the engine has been turned
off long
enough for the oil to drain back into the oil pan.
2-86 -