CHEVROLET COBALT 2007 1.G Owners Manual

✍NOTES
141

Instrument Panel Overview
142

The main components of your instrument panel are the following:
A. Side Window Outlets. SeeClimate Control
System on page 158.
B. Air Outlets. SeeOutlet Adjustment on
page 161.
C. Turn Signal/Multifunction Lever. SeeTurn
Signal/Multifunction Lever on page 145.
D. Cruise Control Buttons (If Equipped) and
Driver Information Control Buttons. SeeCruise
Control on page 149andDriver Information
Center (DIC) on page 181.
E. Instrument Panel Cluster. SeeInstrument
Panel Cluster on page 165
F. Audio Steering Wheel Controls (If Equipped).
SeeAudio Steering Wheel Controls on
page 222.
G. Hazard Warning Flashers Button. SeeHazard
Warning Flashers on page 144.
H. Windshield Wiper/Washer Controls. See
Windshield Wipers on page 147andWindshield
Washer on page 148.
I. Audio System. SeeAudio System(s) on
page 192.J. Fog Lamp Button (If Equipped). SeeFog
Lamps on page 154.
K. Trunk Release. SeeTrunk on page 102.
L. Instrument Panel Brightness Control. See
Instrument Panel Brightness on page 154.
M. Horn. SeeHorn on page 144.
N. Cigarette Lighter (If Equipped). SeeAshtray(s)
and Cigarette Lighter on page 157.
O. Shift Lever (Manual Shown). SeeManual
Transaxle Operation on page 121and
Automatic Transaxle Operation on page 118.
P. Climate Controls. SeeClimate Control System
on page 158.
Q. Passenger Air Bag Status Indicator and Heated
Seats Button (If Equipped). SeePassenger
Airbag Status Indicator on page 168and
Heated Seats on page 11.
R. Glove Box. SeeGlove Box on page 136.
143

Hazard Warning Flashers
The hazard warning ashers let you warn the
police and others that you have a problem.
The front and rear turn signal lamps will ash
on and off.
The hazard warning
asher button is located
in the center of the
instrument panel.
Press the button to make the front and rear turn
signal lamps ash on and off. Press the button
again to turn the ashers off.While the hazard warning ashers are on, the turn
signals do not work.
The hazard warning ashers work no matter what
position the key is in, and even if the key is not
in the ignition switch.
Other Warning Devices
If you carry reective triangles, you can set them
up at the side of the road about 300 feet (100 m)
behind your vehicle.
Horn
To sound the horn, press the center pad on the
steering wheel.
144

Tilt Wheel
A tilt wheel allows you to adjust the steering wheel
before you drive. You can raise the steering wheel
to the highest level to give your legs more room
when you enter and exit the vehicle.
The lever that allows you to tilt the steering wheel
is located on the left side of the steering column.
To tilt the wheel, pull down the lever. Then move
the wheel to a comfortable position, pull up
the lever to lock the wheel in place.
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
GTurn and Lane-Change Signals. See
Turn and Lane-Change Signals on page 146.
53Headlamp High/Low-Beam Changer.
SeeHeadlamp High/Low-Beam Changer on
page 146.
Flash-to-Pass. SeeFlash-to-Pass on page 146.
OExterior Lamp Control. SeeHeadlamps on
page 152.
145

Turn and Lane-Change Signals
The turn signal has two upward (for right) and
two downward (for left) positions. These positions
allow you to signal a turn or a lane change.
To signal a turn, move the lever all the way up
or down. When the turn is nished, the lever will
return automatically.
An arrow on the
instrument panel
cluster will ash in the
direction of the turn
or lane change.
To signal a lane change, raise or lower the lever
until the arrow starts to ash. Hold it there until you
complete your lane change. The lever will return
by itself when you release it.
As you signal a turn or a lane change, if the arrows
ash rapidly, a signal bulb may be burned out and
other drivers will not see your turn signal. If a bulb is
burned out, replace it to help avoid an accident.If the arrows do not go on at all when you signal a
turn, check the fuse. SeeFuses and Circuit
Breakers on page 384.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high
beam, push the turn signal lever away from you.
When the high beams
are on, this light on
the instrument panel
cluster will also be on.
To change the headlamps from high beam to low
beam, pull the turn signal lever toward you.
Flash-to-Pass
This feature lets you use your high-beam
headlamps to signal a driver in front of you
that you want to pass.
To use it, pull the turn signal/multifunction lever
toward you until the high-beam headlamps
come on, then release the lever to turn them off.
146

Windshield Wipers
Use this lever, located on the right side of the
steering wheel, to operate the windshield wipers.
9(Off):Move the lever to this position to
turn off the windshield wipers.
&(Intermittent; Speed Sensitive Wipers):
Move the lever to this position for intermittent or
speed sensitive operation. The amount of delay
time varies between wiping cycles due to the delay
setting selected or the speed of the vehicle.
x(Delay):While the lever is in the intermittent
position, turn the intermittent adjust band with this
symbol on it up or down to select a shorter or longer
delay between wiping cycles. To the left of the
adjust band are bars, increasing in size from bottom
to top, that indicate the frequency of the wipes.
Smaller bars mean the wipers movement is less
frequent. Larger bars mean the movement is more
frequent.
6(Low Speed):Move the lever up to the
rst setting past intermittent, for steady wiping at
low speed.
1(High Speed):Move the lever up to the
second setting past intermittent, for wiping
at a high speed.
8(Mist):Move the lever all the way down to
this position for a single wiping cycle. Hold it there
until the windshield wipers start; then let go.
The windshield wipers stop after one wiping cycle.
If additional wiping cycles are needed, hold the
lever down longer.
147

Damaged wiper blades can prevent you from
seeing well enough to drive safely. Clear ice and
snow from the wiper blades before using them
to prevent damage.
If the wiper blades are frozen to the windshield,
carefully loosen or thaw them. If your blades
do become damaged, get new blades.
Heavy snow or ice can overload the wiper motor.
A circuit breaker stops the motor until it cools.
Clear away snow or ice to prevent an overload.
If the motor gets stuck, turn the wipers off,
clear away the snow or ice, and then turn the
wipers back on.
As an added safety feature, if the wipers are on
for more than 15 seconds, the vehicle’s headlamps
turn on automatically. They turn off 15 seconds
after the wipers are turned off.Windshield Washer
To wash the windshield, press the button at the
end of the lever until the washers begin.
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
When the button is released, the washers stop,
but the wipers continue to wipe about three times
or resume the previous speed.
148

Cruise Control
With cruise control, you can maintain a speed
of about 25 mph (40 km/h) or more without
keeping your foot on the accelerator. This can
really help on long trips. Cruise control does not
work at speeds below 25 mph (40 km/h).
{CAUTION:
Cruise control can be dangerous where
you cannot drive safely at a steady speed.
So, do not use your cruise control on
winding roads or in heavy traffic.
Cruise control can be dangerous on
slippery roads. On such roads, fast
changes in tire traction can cause
excessive wheel slip, and you could
lose control. Do not use cruise control
on slippery roads.
Setting Cruise Control
{CAUTION:
If you leave your cruise control on when
you are not using cruise, you might hit a
button and go into cruise when you do
not want to. You could be startled and
even lose control. Keep the cruise control
switch off until you want to use cruise
control.
The cruise control
buttons are located on
the left side of the
steering wheel.
149

J(On/Off):Press this button to turn the cruise
control system on and off.
RES+ (Resume):Press this button to resume a
set speed and to accelerate the speed.
SET– (Set):Press this button to set a speed and
to decrease the speed.
To set a speed do the following:
1. Press the on/off button to turn cruise control on.
The indicator light on the button will come on.
2. Get to the speed you want.
3. Press the SET– part of the control button
and release it. The CRUISE ENGAGED
message will appear on the Driver Information
Center (DIC) to show the system is engaged.
4. Take your foot off the accelerator pedal.
If the vehicle is in cruise control and the Traction
Control System (TCS) begins to limit wheel spin,
the cruise control will automatically disengage.
SeeEnhanced Traction System (ETS) on
page 234. When road conditions allow,
the cruise control can be used again.Resuming a Set Speed
Suppose you set the cruise control at a desired
speed and then you apply the brake. This, of
course, disengages the cruise control. To return to
the previously set speed, you do not need to go
through the set process again. Once you are going
about 25 mph (40 km/h) or more, you can press
the RES+ part of the button briey.
This will take you back up to your previously
chosen speed and stay there.
Increasing Speed While Using
Cruise Control
There are two ways to go to a higher speed.
1. Disengage the cruise control by applying the
brake pedal but do not turn it off. Accelerate
to a higher speed and reset the cruise control.
2. If the cruise control system is already engaged,
press the RES+ part of the button. Hold it there
until you get up to the speed desired, and then
release the button. To increase the vehicle
speed in very small amounts, press the RES+
part of the button briey and then release it.
Each time you do this, the vehicle will go
about 1 mph (1.6 km/h) faster.
150