CHEVROLET EXPRESS 1996 1.G Owners Manual

Downloaded from www.Manualslib.com manuals search engine 8. Then replace the pressure cap. At any time during
this procedure
if coolant begins to flow out of the
filler neck, reinstall the pressure cap. Be sure the
arrows
on the pressure cap line up like this.
Engine Fan Noise
Your vehicle has a clutched engine cooling fan. When the
clutch is engaged,
the fan spins faster to provide more air
to cool the engine. In most every day driving conditions,
the fan
is spinning slower and clutch is not fully engaged.
This improves fuel economy and reduces fan noise.
Under heavy vehicle loading, trailer towing and/or high
outside temperatures, the fan speed increases
as the clutch
more
fully engages. So you may hear an increase in fan
noise. This
is normal and should not be mistaken as the
transmission slipping
or making extra shifts. It is merely
the cooling system functioning properly. The fan will
slow down when additional cooling is not required and
the clutch partially disengages.
You may also hear this Fan noise when you start
the engine. It will go away as the fan clutch
partially disengages.
5-19

Downloaded from www.Manualslib.com manuals search engine If a Tire Goes Flat
It’s unusual for a tire to “blow out” while you’re driving,
especially if you maintain your tires properly. If air goes
out of a tire, it’s much more likely to leak out slowly.
But
if you should ever have a “blowout,” here are a few
tips about what
to expect and what to do:
If a front tire fails, the flat tire will create a drag that
pulls the vehicle toward that side. Take your foot off the
accelerator pedal and grip the steering wheel firmly.
Steer to maintain lane position, and then gently brake to
a stop well out of the traffic lane.
A rear blowout, particularly on a curve, acts much like a
skid and may require the same correction you’d use in a
skid. In any rear blowout, remove your foot from
the
accelerator pedal. Get the vehicle under control by
steering the way
you want the vehicle to go. It may be
very bumpy and noisy, but you can still steer. Gently
brake
to a stop -- well off the road if possible.
If a tire goes flat, the next part shows how to use your
jacking equipment
to change a flat tire safely.
Changing a Flat Tire
If a tire goes flat, avoid further tire and wheel damage
by driving slowly to a level place. Turn
on your hazard
warning flashers.
I
Changing a tire can cause an injury. The vehicle
can slip
off the jack and roll over you or other
people. You and they could be badly injured.
Find a level place to change your tire.
To help
prevent the vehicle from moving:
1. Set the parking brake firmly.
2. Put the shift lever in PARK (P).
3. ”urn off the engine.
To be even more certain the vehicle won’t move,
you can put blocks at the front and rear
of the
tire farthest away from the one being changed.
That would be the tire on the other side of the
vehicle, at the opposite end.
5-20

Downloaded from www.Manualslib.com manuals search engine Removing the Spare Tire and Tools
The following steps will tell you how to use the jack and
change a tire.
Your spare tire is stored underneath the rear of your
vehicle. You will use the ratchet
and extension to lower
the spare tire.
5-21

Downloaded from www.Manualslib.com manuals search engine NOTICE:
Never remove or restore a tire frondto a stowage
position under the vehicle while the vehicle
is
supported by a jack. Always tighten the tire
fully against the underside of the vehicle when restowing
A flat rear tire reduces clearance to remove the spare
tire. If there is less than
12 inches (30.48 cm) between
the ground and the rear bumper or any trailer hitch, jack
up the vehicle
until the flat tire is off the ground.
(See “Removing
the Flat Tire” and “Installing the
Spare Tire,’’ Steps
4 through 8, in this section.)
Unless your vehicle has a flat rear tire, do not remove
or
restore a tire from/to a stowage position under the
vehicle while the vehicle is supported by a jack. Always
tighten the tire
fully against the underside of the vehicle
when restowing.
If you have a vehicle which was completed from a cab
and chassis, refer to the information from the body
suppliedinstaller.
The spare tire
is a full size tire, like the other tires on
your vehicle.
For cargo vans, the jack
is secured
in the rear
Remove the retaining wing bolt and lift
it off the
mounting bracket. Set the jack and jacking equipment
near the
flat tire.
5-22

Downloaded from www.Manualslib.com manuals search engine For passenger vans, the jack is secured on the rear
passenger side floor
of the vehicle.
Remove the retaining wing
bolt and lift it out of the
mounting bracket. Set the jack and jacking equipment
near the flat tire.
The ratchet has an UP side and a DOWN side.
5-23

Downloaded from www.Manualslib.com manuals search engine Attach the ratchet, with the DOWN side facing you, to
the extension. The extension has a socket end and a flat
chisel end.
Put the flat end
of the extension on an angle through the
hole
in the rear door frame, above the bumper. Be sure
the flat end connects into the hoist shaft.
Turn the ratchet counterclockwise to lower the spare tire
to the ground.
If you are changing a flat rear tire and the
vehicle is already jacked up, use the jack handle and
extension
to hook the cable. Then pull the spare from
beneath the vehicle.
If the retainer pulls out, hook the inside
of the wheel and
pull the spare tire out from under
the vehicle.
When the tire has been lowered, tilt the retainer at the
end
of the cable and pull it through the wheel opening.
I NOTICE:
To help avoid vehicle damage, do not drive
vehicle before the cable
is restored.
5-24

Downloaded from www.Manualslib.com manuals search engine Jacking Tool Storage
A. Socket
B. Jack Handle
C. Ratchet
D. Jacking Tool Storage Box
E. Jack Handle Extension The
tools
you’ll be using include the jack (A), jack
handle extension
(B), jack handle (C), socket (D) and
the ratchet
(E).
5-25

Downloaded from www.Manualslib.com manuals search engine Removing the Wheel Covers and Locking
Wheel
Nuts
1. You will need to take off the wheel nut caps to reach
your wheel nuts.
2. Loosen the plastic nut caps with the ratchet and
socket and remove them. Make sure the DOWN
side faces you.
5-26

Downloaded from www.Manualslib.com manuals search engine Removing the Flat Tire and Installing the
Spare Tire
3. Remove the center cap.
I. With the DOWN side Facing you, use the ratchet and
socket
to loosen all the wheel nuts. Don't remove
them yet.
5-27

Downloaded from www.Manualslib.com manuals search engine 2. The jack has a bolt on the end. AtLach the socket end
of the extension to the jack bolt.
Attach the ratchet to the extension with the UP side
facing
you.
3. Rotate the ratchet clockwise. That will raise the jack
lift head a little.
Front Position
5-28