ESP CHEVROLET MONTE CARLO 1981 4.G User Guide

Downloaded from www.Manualslib.com manuals search engine The Mist feature, intended to remove incidental windshield spray such as from."
passing vehicles is activated by moving the control knob to the extreme left ,­
and holding it in this posnion. The wipers will continue to operate until tile
control knob is released and allowed to return to the OFF position . .
The washer system is operated by depressing the control knob for one or two
seconds in any position.
In the OFF position the wipers will oper,ate 3 to 5
times and then stop .
Ught Switch
The three-position light switch controls the headlights, taillights, parking ~ghts, sidemarker lights, instrument lights. and dome lights as shown. Instrument light
intensity can
be varied by turning knob clockwise or counterclockwise. Full
counterclockwise position turns on interior light An optional head lamp warning
chime sounds when the ignition key is. placed in either the OFF, ACC or LOCK
positions. , ....
. ,-"",,.
NOTICE: When the parking lamps or t)Hd1ampS .... to be operated with the key in the OFF position, the reminder-chime can be shUt-Of' by turning the light switch knob until the instrument elu.1er Ifghts are not on. '
The headlarnp circuit is protected by a circuit breaker in the light switch. An
overload on the breaker will,cau$e the lamps to "flicker" on and off. If this
condnion develops , have your ·headlamp wiring checked immediately. The
headlight beam changer is located in the Turn Signal Lever; for operation see
Section 2 under heading "Turo Signal and Headlight Beam Lever."
Headlight High ,Beam Indicator Ught
The he!).dlights of your vehicle have high and ... loW beams to provide you with
proper nighttime visibility for most driving condnions. The "low" beams are
used during most city driving . The
"high" beams are especially useful when
driving on dark roads sinCe they provide long range illumination . The headlight
beam indicator light (located on the speedometer face) will be
ON whenever
the high beams or "brights " are in use. The turn signal l<lver controls the
headlight beams and is described in "Steering Column Controls ."
Headlamp "ON" Warning Chime
The optional headlarrl> reminder chime provides' an audible warning thai the
main
light switch is in one 0/ the "on" posnions, either parking lights or
headlights. .
2-21

Downloaded from www.Manualslib.com manuals search engine SECTION 4
APPEARANCE CARE
CAUTION: Some cleaners may' be poisonous or flammable, and their Improper ' use
may cause personal injury Or damage the inside of the vehicle. Therefore. when-cleaning the inside -of the vehicle , DO NOT USE votatile cleaning solvents tueh _: acetone , lacquer thi"".r., enamel reducer., nail polish remover.; or suCh cleaning materials as laundry soaps, btl.eMs or reducing agents except .a noted in the fabric cleaning advice on stain removal which follows. NEVER use carbon tetrachloride, gasoline, 'benzene, or naphtha for any cleaning purpose.
Overexposure
to these vapors may result in 8 hNIIh problem. This is even more likely to occur in small, unventileled _spaces. tt is recommended thIIl ,II vehicle cf<!ors be opened 'or ventilatiOn whe~ ANY , cleaning agene. or other chemica. are_.used in the interior. Approved respiratory ,protection equipment rTi8y' be nMded. Follow the INInufllCturer's advice WHENEVER cleaning agents or other' chemlca'a are' used, inside or 9Utside the vehicle.
NonCE: To avoid possible permanent discoloration of white-or light colored seata, DO NOT let mat_58ls with unstab'e dyes corne in contact with seat trim materials until these materials are tota.Ny dry. (This Inch •• s C*1ain type$ of casual clothing , such as colored denims, corduroys, leather.and suedes; also decorative paper, etc.)
CARE AND CLEANING OF THE INTERIOR
With the use of modern trim materials, it is' VERY IMPOR.T~NT.)tJatyou use
proper
cleaning techniques and cleaners. Failing to do this on the first cleaning
may
result in water spots, spot rings ; or setting of stains or soilage, all of which
are
more difficultt'! remove.i~ ~~nd cleaning. . '
Some
of the foilo;';ing cleaning"insi,UctiOns are in CAPITAL LETIERS. These
are especially important and MUST be performed.
Dust
and loose dirllhatcollect on interior . fabrics should be removed oIIen with a vacuum cleaner or soft bristle brush . Wipe vinyl or leather trim regularly with
a clean damp
cloth. Normal trim soilage, spots, or stains can be cleaned with
these GM cleaners:
Dncrlptlon
G.M.Spot lifter 8 oz. (.237L)SoJvent Type . G.M. Multi-Purpose Powdered Cleaner
G.M. Part No.
1051398
6
lb. (2 .72 Kg) Foam TyPe 1050429 The above products are 'excellent cleaners when u:;ed properly.
They . are '
available through 'your' Author,zed dealer.
Remember these basic steps before cleaning :
1. Remove stains as quickly as possible before they become "set"
2. Use a clean cloth or sponge ; and change to a clean area often. (A SOFT
brush may be used if stains jlersist)
3 .
Use 'solvent-type cleaners only in a well ventilated area; also, do not
saturate the stained
area.
4-1

Downloaded from www.Manualslib.com manuals search engine COMPUTER COMMAND CONTROL SYSTEM
Your new vehicle has a special emission contrOl system, called the Computer
Command Control system. Some vehicleS sold in Canada also have the
Computer Command Control system. II your Canadian vehicle has a "CHECK
ENGINE" light,
it dOes have the Computer Command Control system.)
The Computer Command Control system monitors . the .exhaust stream with
an
oxygen sensor. Based on sensor signals, the electronic control module adjusts
the carburetor air-fuel ratio as needed. It is very important to use only
unleaded gasoline in vehicles equipped with the Computer COmmand Control
system . .Leaded gasoline will damage the oxygen sensor and may affect
. emission controL .
On
all vehicles with the COmpute r Command Control system, a "CHECK
ENGINE" ligtit
on the instrument panel is designed to come on during engine
starting, to
let you knowthe bulb .is working. (The light will stay on a'shdl1iime
after the. engine starts.) If. the light comes on while driving, service to the
Computer Command Control system may be. required. Although your vehicle
may
still be drivable,see yoyr dealer as SOon as possible for an inspection of
the system.
Continued
driving · Without having the Computer Command Control system
serviced could cause damage to the emiSsion control system. It could also aftect fuel economy and drivability. .. ..
ENGINE OIL AND FILTER RECOMMENDATIONS
Checking 011 Level ,>,-.. ,
The engine oil must be kept at the right level to. help assure proper lubrication
of your vehicle' .s engine.
It is the owner's responsibility to' cheCk the oil level at
regular': infervals '{such . 'as . "e~~Y"JHflLstop), according ·to ' the following instruct ions . It is normal for an engine-O to use Some oil, and most engines may
use
more oil when they are new . " .
• The best time to check' the engine Orffevel is when the oil IS warm, such as
during a
fuel stop. First, wait about 5 minutes for the oil to drain back to the oil pan. Then, pull out the dipstick on the side of the engine block (either
right or left). Wipe
it clean and. push the dipstick back down all the way.
Now,
pull out the dipstick and look at the oil level .on the dipstick.
Some dipsticks have "Add" and "Full" lines. Others are marked "Add lOt"
and "OperatlngRange ." In all cases, keep the oil level above the "Add" line_ Push the dipstick .oock down alilheway after taking the reading . Add oil , if needed . . .
• If you check the oil level when the oil is cold, do not iun the engine first.
The
cold oil will not drain back to the pan fast enough to give a tr ue oil
level. . .
Ch '
oosing the Right Quality on
Engine oils are labeled on'the containers with variOus API (Amercian Petroleum Institute) deSignations of·quality. Artewhigher-quality category of engine 011,
designation "SF", was introduced early in 1980. Be sure the oil you use has
the
API designation "SF," either alone or shown with other designations . Do not use oils labeled only SA, SB,SC, SO,' SE, CA, CB,CC, or CD; or oils
with a combination of any of these categories-like SE/CD.
5-3

Downloaded from www.Manualslib.com manuals search engine 4. Close the drain valve. Install the block drain plugs, if removed. Add water
until the system is
filled and run the engine until the upper radiator hose is
hot
again.
5. Repeat steps 3 and 4 several times until the drained liquid is nearly colorless.
6. Drain the system, then close the radiator drain valve tightly. Install block
drain plugs, if removed.
7. Disconnect all hoses from the coolant recovery tank. Remove the recovery
tank
and pour out any fluid. Scrub and clean the inside of the recovery
tank with soap and water. Flush it well with clean water, then drain it.
Reinstall the recovery tank and hoses.
8. Add enough water and ethylene glycol antifreeze (meeting GM
Specification 1899-M) to provide the required cooling, freezing and
c()rrosion protection, Use a solution that is at least 50 percent antifreeze out no mOre than 70 percent antifreeze. Fill the radiator to the base of the
filler neck
and fill the coolant recovery tank to the "Full Hot" mark. Put the
recovery tank cap back on.
9. Run the engine, with the radiator cap removed, until the upper radiator
hose is hot.
10. With the engine idling, add coolant to the radiator until it reaches the
bottom of the filler neck. Install the radiator cap, making sure the arrows on the cap line up with the overflow tube.
iI is the owner's responsibility to,
'. -Main)!!!n cooling system freeze protection at -3rC (-34'F) to ensure protection against corrosion and loss of coolant from boiling. (A 50/50
mixture of water and ethylene glycol antifreeze will provide freeze
protection to -37'C or -34'F.) You should do this even if you don't
expect freezing temperatures.
• Add ethylene glycol base' antifreeze that meets GM Specification 1899-M
when antifreeze haS to be added because of coolant loss or for more
protection against freezing at temperatures lower than -37'C (-34'F).
NOTICE: Do "otute methanol-base antifreeze, Of alcohol,or plain water alone, in your vehicle at any time. They will boil at a lower point than that at which the "TEMP"
light (or temperature gage) will warn of overheating,. and they do not provide proper protection against cOrrosion.
Radiator Pressure Cap
The radiator cap, a 105 kPa (15 psi) pressure type, must be installed tightly,
otherwise coolant may be lost and damage to engine may result from
overheating. Radiator pressure
caps should be checked periodically for proper
operation. If replacement is required, an AC cap is recommended.
Thermostat
The engine coolant temperature is controlled by a thermostat. It stops coolant
flow
through the radiator until a preset temperature is reached. This thermostat
is installed in the engine
coolant outlet on the engine block. The same thermostat is used in both winter and summer. When a replacement is needed, AC"Delco parts are recommended.
5-8

Downloaded from www.Manualslib.com manuals search engine STANDARD EXTRA B C o
TIRE-LOAD AND INFLATION PRESSURES
TIRE lOAO RAlliGE
-{METRIC SIZE TIRE) " -{METRIC SIZE T!RE) -(ALPKA-NUMIiRIC SJZETIRE) -(ALPHA-NUMERIC SIZE TIRE) -(ALPHA-NUMERIC SIZE TIRE)
MAXIMUM COLO INHATtoN "'E$SURE
2
40 kPI 280 kPa 220 kPa 2M! kPt 27S kP.
t 35 psi J (41 psi) (32 psi) (36 psi) (40 p.JiI
TIRE LOAD RANGE IS MOLDED Off TIRE. !SEE I UUSTRATIOff ON PAGE ,So11 fOR lOCATION ON THE TIRE S IDEWALl! .
4. Always use a tire pressure gage when checking inflation pressures (we
suggest
you purchase a quality pocket-type gage). Simply looking at the
tires to check inftation pressures is not enough , especially with radia l tires .
Underinflated radial tires may
look like correctly inflated radial tires. H the.
inflation pressure on a tire is often low , have your d9aler correct the cause.
) , I" , "
,
~ , ~ , , , , ) ,
,
,
'"
,
~
'"
,
0:: ~ , , ~ :0 , ,
PROPERLY INFlATED IMPROPERLV INRATED
l ___ ~_~)
y IlADIAL TIRE
5. Be sure to put the tire inflation valve caps back on, if so equipped. This
will help keep dirt · and moisture from getting into the valve core which
could cause a leak.
6. If an air loss occurs while driving, do not drive on the flat tire more than is
needed to stop safely. Driving even a short distance
ona flat tire can
damage a tire and wheel beyond repair.
Inspection and Rotation
Front and rear tires perlorm different jobs and can wear differently depending
on the types of roads driven , your driving habits, etc .
For longer tire
life, you should inspect and rotate your tires as recommended in
Section A of the Maintenance Schedule folder. Many car and tire dealers will perform a free tire inspection to look for uneven or abnormal tire wear (usually
caused
by wrong inflation pressures, lack of regular rotation, improper wheel
alignment, out
of balance tires, or poor driving habits).
After rotation , adjust the front
and. rear tire pressures (see the Tire Placard)
and be sure to check wheel nut tightness . (Wheel nuts should also be
tightened at certain intervals; see the Wheel Nut Torque Caution in "In Case of
Emergency" section,
page 3·7, for further information.)
5-13

Downloaded from www.Manualslib.com manuals search engine When replacing tires with those not having a TPC Spec. No., you should use
the same size,
load range, and constructiontype (bias, bias-bened, or radial)
as the original tires on your
vehicle . Although ~ is not generaly recommended ,
some alpha-size and metric-size tires can be interchanged. (For size
equivalency, contact your Chevrolet
dealer or a tire dealer) . A different size or
type of tire may affect ride,
handling, speedometer /odometer calibration,
vehicle ground clearance , and tire or tire chain clearance to the body or
chassis .
II replacing only a single tire, it should be paired on the same axle with the least worn tire of the other three.
UNIFORM TIRE QUALITY GRADING
The following information relates to the tire grading system developed by the
National Highway Traffic Safety' Adminlslration which will grade tires by
treadwear, traction and temperature performance.
TREADWEAR
The treadwear grade is a comparative rating based on the wear rate of the tire
when tested under
controlled conditions on a specified government test
course . For example, the tire graded 150 would wear one and a haij (1-1/2)
times as well on the government course as a tire graded 100. The relative
performance of tires depends upon the. actual conditions of their _ use , however ,
and may depart significanlly from the norm due to variations in driving habits , service practices and. differences in road characteristics and climate.
TRACTION -A, B,C
. T~~tr~ction grades, from highest to lowest are: A, B, and C. They represent
the ' fiie'sability to stop on wet pavement as measured under controlled
conditions on specified government test surfaces of asphalt and concrete . A
tire marked C may have poor traction performance .
Warning: Thetr.ction grade assigned to this tire is based on braking (straight-ahead) traction tests and· doellnot include cornerillg (turning) tractlon.
TEMPERATURE -A, B, C
The ·temperature grades are A (the highest), B, andC, representing the tire's
resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditio 'ns on a specified indoor laboratory test wheel.
Sustained 'high temperature can cause the material of the tire to degenerate
and reduce tire
life, and excessive temperature can lead to sudden tire failure .
The grade C corresponds to a level of performance which all passenger car
tires must meet under the Federat Motor Vehicle Safety Standard No.
109 . Grades B and A represent higher levels of performance on the laboratory test
wheel than the minimum required by law.
Warning: The
temperature grade for Ihis tire is established for a tire that
is properly inflated and not overloaded. Excessive speed, underinllaiion, or excessive loading, either separately or in combination, can cause heat
buildup and possible lire failure.
5-16

Downloaded from www.Manualslib.com manuals search engine AI Ihis lime your lires mayor may nol have a grade. These grades will be
molded on the sidewalls of passenger car lires over Ihe nexl several years
according to a schedule established by the Nalional Highway Traffic Safety Administration and the tire manufacturers.
While the lires available as standard or optional equipment on General
Motors
vehicles may vary with respect to these grades, all such tires
meet General Motors performance standards and have been approved
for useon General Motors vehicles.
All passenger car tires must conform to Federal safety requirements In addition to these grades.
You should
replace your tires when:
I. The lires are worn to a point where 1.6 millimeters (2/32 inch) or less
tread remains, or the cord or fabric
is showing . To help you detect this,
your tires have built-in tread wear indicators that appear between the tread
grooves when the tread is 1.6 millimeters (2/32 inch) or less. When the
indicators. appear in two or mors adjacent grooves at three. spots around Ihe tire, the tire should be replaced.
TREAD WEAR INDICATORS
lOAD RANG[
........ _.-' ;'CotfS1WC1l0N UtAMI'L[ TilE
2. The tread or sidewall is cracked, cut or snagged deep enough to expose
the cord or fabric.
3. The tire has a bump , bulge or split.
4. The tire has a puncture, cut, or other injury that can't be correctly repaired
because of the size or location of the injury.
Wheel Replacement
Damaged wheels must be rePlaced. For example, replace wheels if they are bent, cracked , or heavily rusted , or if _ wheel nuts ohen become loose. Also
replace wheels which leak air (except" some aluminum wheels which can be repaired-- see your authorized dealer).
Do not use bent wheels which have been -straightened, and do not use inner
tubes in leaking wheels designed for tubeless tires. Such wheels may have
structural damage
and could fail without warning. When replacing wheels for
any reason, the
new wheels should be equal in load limit, diameter, width,
offset. and mounting configurations to those
originally installed on your vehicle.
5-17

Downloaded from www.Manualslib.com manuals search engine SECTION 6
OWNER ASSISTANCE
Your satisfaction and goodwill are important to your dealer and to us. Normally, any problems with the sales transaction or the operation of your car
will be handled by your dealer's Sales or Service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can
occur. If your problem has not been handled to your satisfaction, we suggest
you follow these steps:
STEP ONE -Discuss your problem with a member of dealership
management. Complaints can often be quickly resolved at that level. If the
problem has already been reviewed with the Sales or Service manager, contact
the owner of the
dealership or the General Manager.
STEP TWO -Contact the Chevrolet Zone Office closest to you. (Zone offices are listed on the following pages.) In Canada, contact the General Motors Zone Office. If your problem cannot .be quickly resolved by the
dealership without further help, contact the Zone's Consumer Relations
Department, and provide them with:
• Your name, address and telephone number
• Vehicle Identification Number (This is available frornthe car registration or title, or the plate attached to the left top Of the instrument panel and visible
through the windshield.)
• Dealer's name and location.
• Vehicle's delivery date and present mileage.
• Nature of problem.
A convenient'formf~~your useis"il1clud8d in this section.
STEP THREE ~ Contact the Consumer Relations Representative,
Chevrolet Central Office, Chevrolet Motor Division, Warren, Michigan
48090 (313-492-5500). (In Canada, contact the Customer Services
Representative,
General Motors of Canada Ltd .. Oshawa, Ontario, L lJ 5Z6; 416/644-6624). The representative will review all the facts involved. Then, if it
is
felt some further action can be taken, the zone will be so instructed. In any
case, your contact will be acknowledged providing Chevrolet's position in the
matter.
When contacting the Zone or Central Office, please bear in mind that your
problem will likely be resolved in the dealerShip, using the dealer's facilities,
equipment and personnel. So it is suggested that you follow the above steps in
sequence when you have a problem.
Your purchase of a Chevrolet product is greatly appreciated by both your
dealer and Chevrolet. We want to help you any way we can to make sure you
are completely satisfied with your vehicle.
6-1