relay CHRYSLER CARAVAN 2000 Repair Manual

TEST TC-80ACONTINUED - REPAIRING - SOLENOID VALVE CONTROLLER SHORT CIRCUIT
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
KEY OFF. KEY ON. ERASE CODES.
TEST TC-80A DISCONNECT THE DOES THE DRB DISPLAY YES REPLACE THE FUEL
CONTINUED FROM FUEL PUMP ASSEMBLY "FUEL TIMING PUMP ASSEMBLY.*
PREVIOUS PAGE. CONNECTOR.** SOLENOID CONTROLLER
OPEN CIRCUIT"?
NO
KEY OFF.
DISCONNECT THE ECM REMOVE THE DIESEL
HARNESS POWER RELAY.
CONNECTORS.**
WITH A JUMPER WIRE, KEY ON. USING A REPAIR THE FUEL
CONNECT DIESEL POWER VOLTMETER MEASURE IS THE VOLTAGE YES TIMING SOLENOID
RELAY CONN. CAVITIES THE FUEL TIMING ABOVE 1.0 VOLTS? CONTROL CIRCUIT
30 AND 87 (IN PDC). SOLENOID CONTROL FOR A SHORT TO
FIG.1 CKT. FIG.2 VOLTAGE.*
NO
NOTE: BEFORE
REPLACING THE ECM, DID THE FUEL YES REPLACE THE ENGINE
PERFORM TEST NTC-3A INJECTION PUMP CONTROL MODULE.*
TO CHECK INTERNAL PASS TEST NTC-3A?
FUEL PUMP CIRCUITRY.
NO
REPLACE THE FUEL
INJECTION PUMP
ASSEMBLY.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
249
ProCarManuals.com

TEST TC-84ACONTINUED - REPAIRING - TERMINAL 15 PLAUSIBILITY AFTER START-UP
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-84A KEY OFF.
CONTINUED FROM DISCONNECT THE ECM
THE PREVIOUS HARNESS
PAGE. CONNECTORS.**
USING A VOLTMETER, NOTE: BE SURE TO IS THE VOLTAGE
MEASURE ALL ECM EXCLUDE CAVITIES ABOVE 2.0 VOLTS NO REPLACE THE ENGINE
HARNESS CONNECTOR 30,33,45 AND 51 FOR ANY OF THE CONTROL MODULE.*
CAVITIES EXCEPT FROM THIS STEP. MEASUREMENTS?
30,33,45 AND 51.
YES
IS VOLTAGE PRESENT REPAIR SHORT TO
AT ECM HARNESS NO VOLTAGE ON THE
CONNECTOR CAVITIES CIRCUIT THAT
2 OR 28? MEASURED ABOVE 2.0
VOLTS.*
YES
USING A VOLTMETER, REPAIR THE SHORT
REMOVE THE DIESEL MEASURE ECM HARNESS IS THE VOLTAGE YES TO VOLTAGE ON THE
POWER RELAY.** CONNECTOR CAVITY 2. ABOVE 2.0 VOLTS? DIESEL POWER RELAY
OUTPUT CKT.*
FIG.1
NO
TURN IGNITION OFF. THE DIESEL POWER REPAIR THE SHORT
USING AN OHMMETER, RELAY CONTROL CKT. IS THE RESISTANCE YES TO GROUND ON THE
MEASURE BETWEEN AT THE PDC. BELOW 5.0 OHMS? DIESEL POWER RELAY
GROUND AND... CONTROL CKT.*
FIG.2
NO
REPLACE THE DIESEL
POWER RELAY.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
261
ProCarManuals.com

TEST TC-91ACONTINUED - REPAIRING - VEHICLE SPEED SENSOR TROUBLE CODES
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-91A KEY OFF.
CONTINUED FROM
THE PREVIOUS DISCONNECT THE BCM
PAGE. "B" HARNESS
CONNECTOR.**
USING A VOLTMETER,
MEASURE THE VSS IS THE VOLTAGE YES REPLACE THE BODY
TURN IGNITION ON. SIGNAL CKT. BELOW 5.0 VOLTS? CONTROL MODULE.*
FIG.1
NO
KEY OFF.
REMOVE THE DIESEL
DISCONNECT THE ECM POWER RELAY.*
HARNESS
CONNECTORS.* FIG.2
WITH A JUMPER WIRE, KEY ON. USING A REPAIR THE VSS
CONNECT DIESEL POWER VOLTMETER, MEASURE IS THE VOLTAGE NO SIGNAL CIRCUIT FOR
RELAY CONNECTOR THE VSS SIGNAL CKT. ABOVE 1.0 VOLT? A SHORT TO
CAVITIES 30 AND 87 VOLTAGE.*
(IN PDC). FIG.2 FIG.1
YES
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
277
ProCarManuals.com

TEST TC-94ACONTINUED - REPAIRING - VEHICLE THEFT ALARM TROUBLE CODES
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-94A
CONTINUED FROM
THE PREVIOUS TURN IGNITION OFF.
PAGE.
DISCONNECT THE
DISCONNECT THE ECM BODY CONTROL
HARNESS MODULE HARNESS
CONNECTORS.** CONNECTORS.**
USING AN OHMMETER, BETWEEN THE BCM
MEASURE RESISTANCE AND THE ECM. IS THE RESISTANCE YES REPAIR THE OPEN
OF THE IMMOBILIZER ABOVE 5.0 OHMS? IMMOBILIZER SIGNAL
SIGNAL CIRCUIT... CIRCUIT.*
FIG.1
NO
ENGINE CONTROL REPAIR THE
MEASURE RESISTANCE MODULE HARNESS IS THE RESISTANCE YES IMMOBILIZER SIGNAL
BETWEEN THE ... CONNECTOR CAVITY BELOW 5.0 OHMS? CIRCUIT FOR A
38 AND GROUND. SHORT TO GROUND.*
NO
WITH A JUMPER WIRE,
REMOVE THE DIESEL CONNECT DIESEL POWER
POWER RELAY.** RELAY CONN. CAVITIES
30 AND 87 (IN PDC).
FIG.2
USING A VOLTMETER, REPAIR THE
MEASURE ECM IS THE VOLTAGE YES IMMOBILIZER SIGNAL
TURN IGNITION ON. HARNESS CONNECTOR ABOVE 1.0 VOLT? CIRCUIT FOR A
CAVITY 38. SHORT TO VOLTAGE.*
FIG.1
NO
CONTINUE TEST
TC-94A ON THE
NEXT PAGE.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
283
ProCarManuals.com

TEST TC-94ACONTINUED - REPAIRING - VEHICLE THEFT ALARM TROUBLE CODES
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-94A TURN IGNITION OFF. RECONNECT ONLY THE
CONTINUED FROM ENGINE CONTROL
THE PREVIOUS INSTALL THE DIESEL MODULE HARNESS
PAGE. POWER RELAY. CONNECTORS.
KEY ON. MEASURE
USE AN AMMETER IN AMPERAGE FROM BCM IS THE AMPERAGE NO REPLACE THE ENGINE
THE FOLLOWING HARNESS CONNECTOR BETWEEN 1.0 AND CONTROL MODULE.*
STEP. CAVITY 72 TO GROUND. 1.4 MA?
FIG.1
YES
KEY ON. USING THE DRB
OSCILLOSCOPE
RECONNECT THE BODY FUNCTION, SELECT
CONTROL MODULE "LAB SCOPE".
HARNESS CONNECTORS.
SET VOLTAGE RANGE SET TIME RANGE TO
TO +20.0V. SET 0.1S/DIV.
PROBE TO X10.
FIG.2 FIG.3
KEY ON. USING NOTE: A VALID
OSCILLOSCOPE LEAD, IMMOBILIZER SIGNAL
BACKPROBE ECM WILL CYCLE HI AND
HARNESS CONNECTOR LO SIMILAR...
CAVITY 38. FIG. 1
DOES THE DRB
TO THE PATTERN DISPLAY SHOW THE YES REPLACE THE ENGINE
SHOWN IF FIGURE 3. 12 VOLT CONTROL MODULE.*
IMMOBILIZER SIGNAL
CYCLING HI AND LO?
NO
REPLACE THE BODY
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
285
ProCarManuals.com

TEST NTC-2ACHECKING GLOW PLUG OPERATION
Perform TEST NTC-1A Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
THE 2.5L DIESEL GLOW PLUG RELAY #1 GLOW PLUG RELAY #2
START TEST ENGINE UTILIZES SUPPLIES POWER TO SUPPLIES POWER TO
NTC-2A. TWO GLOW PLUG THE GLOW PLUGS IN THE GLOW PLUGS IN
RELAYS... CYLINDERS #1 & #4. CYLINDERS #2 & #3.
PERFORM THIS TEST
ON GLOW PLUG RELAY
#1 THEN REPEAT TURN IGNITION OFF.
TEST FOR GLOW PLUG
RELAY #2.
DISCONNECT EACH KEY ON. USING THE
GLOW PLUG HARNESS DRB, ACTUATE THE
CONNECTOR. GLOW PLUG RELAY.
USING A TEST
LIGHT, PROBE THE DOES THE TEST NO TEST NTC-2A
APPROPRIATE GLOW LIGHT FLASH ON AND CONTINUED ON
PLUG HARNESS CONN. OFF? THE NEXT PAGE.
FIG.1 AND 2
YES
GLOW PLUG CIRCUITRY
OK. REFER TO SERVICE
MANUAL TO CHECK GLOW TEST COMPLETE.*
PLUG OPERATION.
N
O
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
325
ProCarManuals.com

TEST NTC-4ACHECKING THE PCM POWER AND GROUNDS
Perform TEST NTC-1A Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
NOTE: THE BATTERY
START TEST MUST BE FULLY
NTC-4A. CHARGED TO PERFORM
THIS TEST.
TURN IGNITION OFF. WITH AN OHMMETER,
DISCONNECT THE ECM MEASURE ECM IS THE RESISTANCE NO REPAIR THE OPEN
HARNESS HARNESS CONNECTOR BELOW 5.0 OHMS FOR GROUND CIRCUIT.*
CONNECTORS.** CAVITIES 1 AND 27 ALL MEASUREMENTS?
TO GROUND. FIG.1
YES
PROBE DIESEL POWER
USE A TEST LIGHT RELAY CONNECTOR DOES THE TEST NO REPAIR OPEN
IN THE FOLLOWING CAVITY (PDC) 3(30). LIGHT ILLUMINATE BATTERY SUPPLY TO
STEPS. BRIGHTLY? RELAY.
FIG.2
YES
REMOVE THE DIESEL 3(30) AND 5(87). DOES THE TEST
POWER RELAY. CONNECT WITH A TEST LIGHT, LIGHT ILLUMINATE NO REPAIR OPEN DIESEL
A JUMPER WIRE ACROSS PROBE ECM HARNESS BRIGHTLY FOR EACH POWER RELAY OUTPUT
RELAY CONNECTOR CONNECTOR CAVITIES CAVITY? CIRCUIT.*
(PDC) CAVITIES... 2 AND 28. FIG.2
YES
WITH A TEST LIGHT,
PROBE ECM HARNESS DOES THE TEST NO REPAIR THE OPEN
TURN IGNITION ON. CONNECTOR CAVITY 47. LIGHT ILLUMINATE FUSED IGNITION
BRIGHTLY? SWITCH CIRCUIT.*
FIG.1
YES
ECM GROUND
AND POWER
CIRCUITS ARE
OK. TEST
PASSED.
N
O
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
331
ProCarManuals.com

TEST NTC-10ACHECKING THE FUEL HEATER AND THE CRANKCASE VENT HEATER
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TURN IGNITION OFF.
START TEST YES PERFORM TEST
NTC-10A. INSPECT FUSE #16 IS THE FUSE OPEN? NTC-10B.
IN THE PDC.
NO
USING A TEST
REMOVE THE FUEL LIGHT, PROBE RELAY IS THE TEST LIGHT NO REPLACE THE POWER
HEATER RELAY.** CONNECTOR CAVITY ON? DISTRIBUTION
30 (IN PDC). CENTER.*.
FIG. 1
YES
USING A TEST REPAIR THE FUSED
LIGHT, PROBE FUSED IS THE TEST LIGHT NO IGNITION SWITCH
TURN IGNITION ON. IGNITION SW OUTPUT ON? OUTPUT CIRCUIT FOR
CKT (IN PDC). AN OPEN OR SHORT
FIG. 1 TO GROUND.*
YES
WITH IGNITION RELAY CONNECTOR
STILL ON, CONNECT CAVITIES 85 AND 86 IS THE TEST LIGHT NO REPAIR THE OPEN
A TEST LIGHT (IN PDC). ON? RELAY GROUND
ACROSS...CIRCUIT.*
FIG. 1
YES
KEY OFF. DISCONNECT THE
FUEL HEATER AND CONTINUE TEST
INSTALL THE FUEL CRANKCASE VENT TURN IGNITION ON. NTC-10A ON THE
HEATER RELAY. HEATER HARNESS NEXT PAGE.
CONNECTORS.**
N
O
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
343
ProCarManuals.com

TEST NTC-10ACONTINUED - CHECKING THE FUEL HEATER AND THE CRANKCASE VENT HEATER
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
REPAIR THE OPEN FUEL
HEATER RELAY OUTPUT
CIRCUIT TO THE FUEL
HEATER.*
N
O
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
345
ProCarManuals.com

TEST NTC-10ACONTINUED - CHECKING THE FUEL HEATER AND THE CRANKCASE VENT HEATER
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST NTC-10A CONNECT A TEST
CONTINUED FROM WITH THE IGNITION LIGHT BETWEEN
THE PREVIOUS STILL ON... GROUND AND THE
PAGE. FUEL HEATER RELAY
OUTPUT CKT. AT...
THE CRANKCASE VENT REPAIR THE OPEN FUEL
HEATER HARNESS IS THE TEST LIGHT NO HEATER RELAY OUTPUT
CONNECTOR. ON? CKT FROM THE SPLICE
TO THE CRANKCASE
FIG. 1 VENT HEATER.*
YES
CONNECT A TEST LIGHT REPAIR THE OPEN
ACROSS THE CRANKCASE IS THE TEST LIGHT NO CRANKCASE VENT
VENT HEATER HARNESS ON? HEATER GROUND
CONNECTOR. CIRCUIT.*
FIG. 1
YES
USING AN OHMMETER,
MEASURE RESISTANCE IS THE RESISTANCE NO REPLACE THE
OF THE CRANKCASE BETWEEN CRANKCASE VENT
VENT HEATER. 10.0 AND 16.0 OHMS? HEATER.*
FIG.1
YES
TEST COMPLETE.
N
O
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
349
ProCarManuals.com