warning light Citroen BERLINGO MULTISPACE 2016 2.G User Guide

11 4
Berlingo-2-VP_en_Chap05_Securite_ed01-2016
HAZARD WARNING LAMPS
H
ORN
Press the centre of the steering wheel.
PARKING BRAKE
Applying
Pull the parking brake lever up to immobilise
  your   vehicle.
Check
  that   the   parking   brake   is   applied  
firmly

  before   leaving   the   vehicle.Pull
  on   the   parking   brake   lever,   only
with the vehicle stationary.
In the exceptional case of use of the
parking
  brake   when   the   vehicle   is  
moving,

  apply   the   brake   by   pulling  
gently

  to   avoid   locking   the   rear   wheels  
(risk

  of   skidding).
Press this button, the direction
indicators
 
flash.
They
 
can
 
operate
 
with
 
the
 
ignition
 
off.
The
 
hazard
 
warning
 
lamps
 
should
 
only
 
be used in dangerous situations, when
stopping

 
in
 
an
 
emergency
 
or
 
when
 
driving

 
in
 
unusual
 
conditions.
When
  parking   on   a   slope,   direct   your  
wheels

  towards   the   pavement   and   pull  
the

  parking   brake   lever   up.
There is no advantage in engaging
a
  gear   after   parking   the   vehicle,  
particularly

  if   the   vehicle   is   loaded.
If the parking brake is still on or has not been released properly, this is
indicated
  by   this   warning   lamp   which
 comes

  on   in   the   instrument   panel.
Automatic operation of hazard
warning lamps
When braking in an emergency, depending on the force of deceleration,
the  hazard   warning   lamps   come  
on

  automatically.  
They
  switch   off  
automatically

  the   first   time   you  
accelerate.
It

  is   also   possible   to   switch   them   off   by  
pressing

  the   switch   on   the   dashboard.Releasing
Pull the lever up slightly and press the
button  to   lower   the   parking   brake   lever.
driving safely

ABS
ABS
11 8
Berlingo-2-VP_en_Chap05_Securite_ed01-2016
ANTI-LOCK BRAKING SYSTEM
(ABS / EBFD)
The ABS   and   EBFD   (electronic   brake  force
  distribution)   systems   improve   the  
stability

  and   manoeuvrability   of   your  
vehicle

  on   braking,   in   particular   on  
poor

  or   slippery   surfaces.
The
 
ABS
  prevents   locking   of   the  
wheels, the EBF

d provides control of
the
  braking   pressure   wheel   by   wheel.If
  this   warning   lamp   comes  on,
  accompanied   by   an  
audible

  signal   and   a   message  
in the screen, it indicates a
malfunction

  of   the  
ABS
  which  
could result in a loss of control of the
vehicle

  on   braking.
If
  this   warning   lamp   comes  
on,

  together   with   the   brake  
and

  STOP
 
warning   lamps,  
accompanied

  by   an   audible  
signal

  and   a   message   in   the  
screen,

  it   indicates   a   malfunction   of  
the

  electronic   brake   force   distribution  
which could result in a loss of control of
the

  vehicle   on   braking.
EMERGENCY BRAKING
ASSIST

ANCE (EBA)
In an emergency, this system enables the  optimum   braking   pressure   to   be  
reached

  more   quickly,   press   the   pedal  
firmly

  without   releasing   it.
It is triggered by the speed at which the
brake
  pedal   is   pressed   down.
This
  alters   the   resistance   of   the   brake  
pedal

  under   your   foot.
To
  maintain   operation   of   the  
emergency

  braking   assistance   system:  
keep

  your   foot   on   the   brake   pedal.
Good practice
The anti-lock braking system comes into  operation   automatically   when  
there

  is   a   risk   of   wheel   lock.   It   does   not  
reduce

  the   braking   distance.
o

n very slippery surfaces (ice,
oil, etc...)
  the  
ABS
  may   increase   the  
braking

  distance.   When   braking   in  
an

  emergency,   do   not   hesitate   to  
press

  the   brake   pedal   firmly,   without  
releasing the pressure, even on a
slippery surface, you will then be able
to

  continue   to   manoeuvre   the   vehicle  
to

  avoid   an   obstacle.
Normal
  operation   of   the  
ABS
  may   be  
felt

  by   slight   vibration   of   the   brake  
pedal.
When changing wheels (tyres and
rims),

  ensure   that   these   are   listed   by  
CITROËN

  for   the   vehicle. Stop as soon as it is safe to do so.
In both cases, contact a CITR
o Ë n
dealer
  or   a   qualified   workshop.
driving safely

126
Berlingo-2-VP_en_Chap05_Securite_ed01-2016
126
SEAT BELTS
Height adjustment
Squeeze the control with the return and
slide  the   assembly   on   the   driver's   seat  
side and on the individual passenger
seat

  side.
Fastening
Pull the strap, then insert the tongue
into  the   buckle.
Check
  that   the   seat   belt   is   fastened  
correctly

  by   pulling   the   strap.
Seat belt(s) not fastened
warning lamp Unfastening
Press the red button.
When the vehicle is started,
this
  warning   lamp   comes   on  
if a user at the front has not
fastened

  their   seat   belt.
Good practice
The driver must ensure that passengers use the seat belts correctly
and that they are all strapped in
securely  before   moving   off.
Wherever you are seated in the
vehicle, always fasten your seat belt,
even
  for   short   journeys.
The
  seat   belts   are   fitted   with   an   inertia  
reel

  which   automatically   adjusts   the  
length

  of   the   strap   to   your   size.
d

o not use accessories (clothes pegs,
clips,
  safety   pins,   etc.)   which   allow   the  
seat

  belt   straps   to   fit   loosely.
Ensure that the seat belt has reeled in
correctly
  after   use.
After
  folding   or   moving   a   seat   or   a   rear  
bench seat, ensure that the seat belt
has reeled in correctly and that the
buckle

  is   ready   to   accommodate   the  
tongue.
d

epending on the nature and
seriousness
  of   any   impact,   the  
pretensioning

  device   may   be   deployed  
before

  and   independently   of   inflation  
of

  the   airbags.   It   instantly   tightens  
the seat belts against the body of the
occupants.
Deployment

  of   the   pretensioners   is  
accompanied

  by   a   slight   discharge  
of

  harmless   smoke   and   a   noise,   due  
to the activation of the pyrotechnic
cartridge

  incorporated   in   the   system.
The
 
front
 
passenger's
 
seat
 
may
 
be
 
fitted

 
with

 
a

 
presence

 
detector

,
 
in

 
which

 
case you should not place anything
heavy on this seat as this could trigger
the

 
alert.
Seat belts

158
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Levels
Cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When
  the   engine   is   warm,   the  
temperature

  of   the   coolant   is   controlled  
by

  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and

  because   the   cooling   system   is  
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has

  dropped,   remove   the   cap   and   top  
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this

  indicates   a   fault   which   must   be  
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes
  as   soon   as   possible,   when  
traffic

  conditions   permit   (until   the  
message

  disappears   and   the   service  
warning

  lamp   goes   off).
d

uring regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating

  may   be   heard   under   the  
dashboard.
If

  the   message   is   still   displayed   and  
if

  the   service   warning   lamp   remains  
on, contact a CITR

o Ë n dealer or a
qualified
  workshop.
Topping up
The
 
level
 
must
 
be
 
between
 
the
 
MIN
 
and

 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required to top up the level, have the
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash and headlamp
wash level
For best quality cleaning and for your
safety, we would advise that you use
products   of   the   CITROËN   range.
For
  optimum   cleaning   and   to   avoid  
freezing,

  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
If
  your   vehicle   is   fitted   with   headlamp  
washers, the capacity of the reservoir
is

  6   litres.
Diesel additive level
(Diesel with particle
filter)
Topping up
This   additive   must   be   topped   up   by  
a

  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
avoid prolonged contact of used oil
with   the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITR

o Ë n dealer (France) or
an
  authorised   waste   disposal   site.
The
 
minimum
 
level
 
of
 
this
 
additive
 
is indicated by lighting of the service
warning

 
lamp,
 
accompanied
 
by
 
an
 
audible

 
signal
 
and
 
a
 
message
 
in
 
the
 
screen.
When this occurs with the engine
running it is due to the start of
saturation

 
of
 
the
 
particle
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).

160
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Checks
Good practice
Bleeding water from the Diesel
filter
Manual gearbox
Have the level checked in accordance with the
  manufacturer's   servicing   schedule.
In order to avoid damaging the electrical units, we strongly
advise you not to use high
pressure washing to clean the engine
compartment.
After
  washing   the   vehicle   dampness,  
or

 
in
  winter,   ice   may   form   on   the   brake  
discs

  and   pads:   braking   efficiency   may  
be

 
reduced.   Make   some   light   brake  
applications to dry and de-ice the
brakes.
If

 
this
 
warning
 
lamp
 
comes
 
on,

 
bleed
 
the
 
filter.
 
Otherwise
 
bleed

 
regularly
 
each
 
time
 
the
 
engine

 
oil
 
is
 
changed.
H

d
i engines use advanced
technology.
 
All

 
work
 
requires
 
special training, so should be
entrusted

 
to
 
a
 
CITROËN
 
dealer.
Depending
 
on
 
country
 
of
 
sale.
To drain the water, unscrew the bleed
screw
 
located
 
on
 
the
 
filter.
o

perate until all of the water no longer
flows
 
in
 
the
 
transparent
 
pipe,
 
then
 
tighten

 
the
 
bleed
 
screw.
Only  use   products   recommended   by  
CITR

o Ë n or products of equivalent
quality   and   specification.
In
 
order   to   optimise   the   operation  
of

 
units   as   important   as   the   braking  
system,

  CITROËN   selects   and   offers  
specific

  products.

161
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Fuel
REFUELLING
Low fuel level
Filling
The  fuel   tank   must   be   filled   with
the
engine off.
-
 
Open
  the   fuel   filler   flap.
-
 
Insert
  the   key,   then   turn   it   a   quarter  
turn.
-

 
Remove
  the   cap   and   hook   it   onto  
the clip located on the inside of the
flap.
When

  filling   with   fuel,  
a mechanical

  system   prevents  
opening

  of   the   left-hand   side   door.  
When

  the   fuel   filler   flap   is   open,   ensure  
that

  no   one   tries   to   slide   this   door.
Once
  the   flap   has   been   closed,   the  
sliding

  side   door   may   jam,   push   the  
door

  to   close   it   then   open   it.
When the low fuel level is
reached,
 
this
 
warning
 
lamp
 
comes

 
on. A
 

label   affixed   to   the   inside   of   the   flap  
reminds

  you   of   the   type   of   fuel   to   be  
used.
Y

ou   must   fill   with   at   least   5   litres   of   fuel  
for

  it   to   be   registered   by   the   fuel   gauge.
When
  the   fuel   filler   cap   is   opened,  
there

  may   be   a   slight   inrush   of   air.  
This
 
vacuum

  is   entirely   normal   and   is   due   to  
the

  sealing   of   the   fuel   system.
When
  filling   the   fuel   tank,   do   not  
continue after the 3rd cut-off of the
nozzle.
 This
 
could
 
cause   malfunctions.
The
 
capacity
 
of
 
the
 
fuel   tank   is  
approximately

 
60
 
litres.
-
 
After

 
filling
 
the
 
fuel   tank,   lock   the  
cap

 
and
 
close
 
the   flap.
Fuel used for petrol
engines
The petrol engines are compatible with E10 bio-petrol (containing 10 %
ethanol),   conforming   to   European  
standards

  EN   228   and   EN   15376.
E85 type fuels (containing up to 85 %
ethanol) are reserved exclusively for
vehicles
  marketed   for   the   use   of   this  
type

  of   fuel   (BioFlex   vehicles).  
The
 
quality

  of   the   ethanol   must   comply   with  
European

  standard   EN   15293.
You then have approximately 8 litres
of
 
fuel
 
remaining.
Fill up without delay to avoid running
out
 
of
 
fuel.
Never
 
risk
 
driving
 
until
 
you
 
run
 
out
 
of
 
fuel

 
as
 
this
 
may
 
damage
 
the
 
emissions
 
control

 
and
 
injection
 
systems.
CHECkS
7

164
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Good practice
While the quantity of
a
dBlue® in
the
 
additive
 
tank
 
is
 
sufficient,
 
no
 
information

 
is
 
displayed.
On
 
the
 
other
 
hand,
 
once
 
the
 
fluid
 
level drops to the quantity needed
for

 
a
 
range
 
of
 
1
 
500
 
miles
 
(2
 
400
 
km)  
driving, you are warned by dif

ferent
temporary
 
signals
 
(warning
 
lamp,
 
message,

 
audible
 
signal).
As
 
more
 
miles
 
are
 
covered,
 
these
 
signals

 
intensify
 
and
 
the
 
message  
becomes

 
permanent.
When the
a
dBlue
® tank is empty, restarting
 
becomes   impossible.
It
 
is
 
strongly
 
recommended   that   you  
do not wait for the successive alerts
before topping-up the a

dBlue
® additive,
but
 
do
 
this
 
as
 
soon
 
as
 
possible.
Filling the AdBlue® tank
For light vehicles, 5 or 10 litre
containers
 
and
 
1.89
  litre  
(1/2 US gallon)

 
bottles   are   available  
from

 
CITROËN
 
dealers,   until   they   are  
equipped

with
a
dBlue
® delivery pumps.
If
 
you
 
want
 
to
 
fill
 
the
 
AdBlue® tank yourself, ensure that you have a
suitable
 
filler
 
pipe,
 
which
 
may   or   may  
not be supplied with the additive
container

.
adBlue®

168
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Filling
Ensure that the vehicle is parked on a flat  and   level   surface.
Pour
  the   contents   of   the   container   /  
bottle

  into   the   dedicated   tank.
After
  filling   the  
AdBlue® tank, observe the
 
following
 
procedure:
-

Switch on the ignition without
starting.
-


W

ait 10 seconds before starting the
engine.
Never
 
dispose
 
of
 
empty  
AdBlue®
containers and bottles in the
household
 
waste.
Place
 
them
 
in
 
a
 
special
 
container
 
provided

 
this
 
purpose
 
or
 
take
 
them
 
to  
your

 
dealer.
k
eep a dBlue
® out of the reach of
children,
 
in
 
its
  original   container.
n

ever transfer a dBlue
® to another
container:
 
it
 
would
 
loose
 
its
  purity.
Never
 
dilute
 
the
 
fluid
 
with
 
water.
Never
 
pour
 
the
 
fluid
 
into
 
the   Diesel   fuel  
tank.
Recommendations on storage
never store containers or bottles of adBlue® in your vehicle.
Freezing of the AdBlue
®
adBlue® freezes at about -11°C (12.2° F) and
 
deteriorates   above   25°C   (77°F).
It
 
is
 
recommended   that   containers   and  
bottles be stored in a cool area and
protected

  from   direct   sunlight.
Under
 
these   conditions,   the   fluid   can  
be

 
kept
  for   at   least   a   year.
a

dditive that has been frozen can
be used once it has thawed out in
ambient air. The
  SCR   system   includes   an  
a dBlue
® tank heater that ensures operation
  of   the   vehicle   in   normal  
conditions.
In exceptional situations, such
as

 
when
 
the
 
vehicle   is   kept   at  
temperatures

  below   -15°C   (5°F)   for   a  
long

 
period,
 
there   may   be   an   emission  
fault alert related to freezing of the a

dBlue
® additive.
Park
 
the   vehicle   in   an   area   at   a   more  
moderate

  temperature   for   a   few   hours  
until

the a dBlue
® becomes a fluid again.
The
 
emissions
 
warning   lamp   does   not  
go

 
off
 
immediately,   but   does   so   after   a  
few

 
miles
 
of
 
driving.
adBlue®