sensor Citroen BERLINGO MULTISPACE RHD 2015 2.G User Guide

55
Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
2  Fast  wipe   (heavy   rain).
1   
Normal
  wipe   (moderate   rain).
l
  
Intermittent
  wipe.
0
  
Of
f.
â

Single wipe
 (press

  downwards).
In the Intermittent
  position,   the   wiping  
speed is in proportion to the vehicle
speed.
WIndScrEEn WIPEr StALK
Manual windscreen wipers
Whenever the ignition has been
switched   off   for   more   than   one   minute,  
with

  the   windscreen   wiper   stalk   in  
position

  2,   1   or   I,   the   stalk   must   be  
reactivated:
-

 
move
  the   stalk   to   any   position,
-
 
then
  move   it   back   to   the   required  
position.
d

o not cover the rain sensor,
located in the centre of the
windscreen,
  behind   the   mirror.Activation
Press
  the   control   downwards.  
a ctivation of the function is
accompanied   by   a   message   in   the  
screen.
d

eactivation / Switching off
Place   the   windscreen   wipers   stalk   in  
position

I, 1 or 2.   Deactivation   of   the  function
  is   accompanied   by   a   message  in
  the   screen.
In
  the   event   of   malfunction   of   the  
automatic

  windscreen   wipers,   the  
windscreen wipers will operate in
intermittent

  mode.
Contact a CITR
o Ë n dealer or a
qualified
  workshop   to   have   the   system  
checked. In the
A ut
O
position, the windscreen
wipers   operate   automatically   and  
adapt their speed to the intensity of the
rainfall.
When not in

A ut
O
  mode,   for   the  
other

  positions,   refer   to   the   manual  
windscreen

  wipers   section.
The   automatic   rain   sensitive  
windscreen

  wipers   function   must  
be

  reactivated   by   pressing   the   stalk  
downwards, if the ignition has been
switched

  off   for   more   than   one   minute.
When   using   an   automatic   car  
wash, switch of

f the ignition to
avoid
  triggering   the   automatic  
wiping.
In winter

, it is advisable to wait for the
windscreen
  to   completely   clear   of   ice  
before

  operating   automatic   wipe.
Automatic rain sensitive windscreen wipers
Steering mounted controls
EaSE oF USE and CoMFoRT
4

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
 65
Good practice
For maximum cooling or heating of the passenger  compartment,   it   is   possible  
to exceed the value 15 by turning until
LO

  is   displayed   or   the   value   27   by  
turning

  until   HI   is   displayed.
o

n entering the vehicle, the inside
temperature
  may   be   much   colder  
(or
  warmer)   than   is   comfortable.  
There
 
is no advantage in changing the value
displayed

  in   order   to   quickly   reach   the  
level

  of   comfort   required.  
The
  system  
will

  use   its   maximum   performance   to  
reach

  the   comfort   value   set.
dIGItAL AIr c O nd I t IO n I n G WI t H SEPA r At E SE tt I n GS
Automatic operation
AutO comfort programme
This   is   the   normal   air   conditioning  
system

  operating   mode.
d
river or passenger side comfort
value
The value indicated in the screen
corresponds   to   a   level   of   comfort   and  
not

  a   temperature   in   degrees   Celsius  
or

  Fahrenheit.
Turn this control to the left
or to the right to decrease or
increase   the   value.  
A 
setting  
around the value 21 provides
optimum

  comfort.   However,  
depending

  on   your   requirements,   a  
setting

  between   18   and   24   is   usual.
d

o not cover the sunshine sensor
located
  on   the   dashboard.
Press this button, the A
ut
O

symbol
  is   displayed.
In accordance with the
comfort
  value   selected,  
the

  system   controls   the  
distribution,

  the   flow   and   the   intake  
of

  air   to   guarantee   comfort   and   a  
sufficient

  circulation   of   air   in   the  
passenger

  compartment.   No   further  
action

  on   your   part   is   required.
When the engine is cold, to prevent an
excessive diffusion of cold air, the air diffuser
will  reach   its   optimum   level   gradually.
For
  your   comfort,   the   settings   are   stored
 when the ignition is switched of

f and are
reinstated
  the   next   time   the   vehicle   is
 started.
The

  automatic   function   will   no   longer   be
 maintained

  if   you   change   a   setting   manually
 (AUT

O   is   cleared).
FOr tHE drIVEr And PASSEnGEr
Ventilation
EASE OF uSE and cOMFOrt
4

 107
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
The audible and/or visual rear parking sensor  system   consists   of   four  
proximity

  sensors,   installed   in   the  
rear

  bumper.  
The
  sensors   detect   any  
obstacle

  which   enters   the   field:   person,  
vehicle, tree, fence, behind the vehicle
during

  the   manoeuvre.
Certain
  objects   detected   at   the  
beginning

  of   the   manoeuvre   will   no  
longer be detected at the end of the
manoeuvre

  due   to   the   blind   spots  
between

  and   below   the   sensors.  
Examples:

  stake,   roadworks   cone   or  
pavement

  post.
Engage reverse gear
r

EA
r
PA
r
KI
n
G SE
n
SO
r
S
display in the screen
Stop the assistance
Change to neutral.
An
 
audible
 
signal
 
confirms
 
the
 
activation

 
of
 
the
 
system
 
by
 
engaging
 
reverse

 
gear.
The
 
proximity
 
information
 
is
 
indicated
 
by

 
an
 
audible
 
signal
 
which
 
becomes
 
more

 
rapid
 
as
 
the
 
vehicle
 
approaches
 
the

 
obstacle.
 
When
 
the
 
distance
 
between the rear of the vehicle and
the

 
obstacle
 
is
 
less
 
than
 
approximately
 thirty
 
centimetres,
 
the
 
audible
 
signal
 becomes
 
continuous.
Parking sensors
SaFETY
5

108
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
Activation / deactivationMalfunction
In the event of a malfunction, when reverse gear is engaged the LE
d in the
button
  comes   on,   accompanied   by   an  
audible

  signal   and   a   message   in   the  
screen.

  Contact   a   CITROËN   dealer   or  
a

  qualified   workshop.
Good practice
In bad weather or in winter, ensure that
the  sensors   are   not   covered   with   mud,  
ice

  or   snow.
The
  system   will   be   deactivated  
automatically

  if   a   trailer   is   being   towed  
or

  if   a   bicycle   carrier   is   fitted   (vehicle  
fitted

  with   a   towbar   or   bicycle   carrier  
recommended

  by   CITROËN).
The
  parking   assistance   cannot,   in  
any

  circumstances,   take   the   place   of  
the vigilance and responsibility of the
driver

.
You can activate or deactivate
the
 
system
 
by
 
pressing
 
this
 
button.
The activation or deactivation
of

 
the
 
system
 
is
 
stored
 
when
 
the

 
vehicle
 
stops.
Parking sensors

136
Berlingo_2_VP_en_Chap06_Accessoire_ed02-2014
Good Practice
In certain cases of particularly arduous
use  (towing   the   maximum   load   up   a  
steep

  slope   in   high   temperatures),   the  
engine

  automatically   limits   its   power.  
In this case,

the air conditioning is
automatically
  cut   off   to   save   engine  
power

.
tyres
Check

  the   tyre   pressures   of   the   towing  
vehicle and of the trailer

, observing the
recommended
  pressures.
Chapter
  7,   "Levels"   section.
If
  the   coolant   temperature  
warning

  lamp   comes   on,   stop  
the vehicle and switch of

f the
engine
  as   soon   as   possible.Brakes
Towing
  increases   the   braking   distance.  Drive
  at   a   moderate   speed,   change  
down

  early   and   brake   gradually.
towbar
We recommend the use of genuine CITRo Ë n towbars and their
harnesses, which have been tested
and
  approved   from   the   design   stage   of  
your vehicle, and that you entrust the
fitting

  of   this   equipment   to   a   CITROËN  
dealer

.
If
  this   equipment   is   not   fitted   by   a  
CITROËN

  dealer,   it   is   imperative   that  
it

  is   fitted   using   the   electrical   pre-
equipment
  installed   at   the   rear   of   the  
vehicle and in accordance with the
manufacturer's

  instructions.
In accordance with the general
instructions
  a   reminder   of   which   has  
been given above, we draw your
attention

  to   the   risk   associated   with  
fitting

  a   towbar   or   electrical   accessory  
not

  recommended   by   CITROËN.  
Fitting

  such   equipment   could   result   in  
the failure of your vehicle's electronic
system.

  Please   obtain   information   from  
the

  Manufacturer   before   fitting   this   type  
of

  equipment.
Side wind
Sensitivity
 
to
 
side
 
wind
 
is
 
increased.
 
Drive

 
smoothly
 
and
 
at
 
a
 
moderate
 
speed.
ABS/

d
S
c
The

 
ABS

 
or
 
DSC
 
systems
 
only
 
control
 
the

 
vehicle,
 
not
 
the
 
trailer
 
or
 
caravan.
Parking sensors
The
 
rear
 
parking
 
sensors
 
system
 
does
 
not

 
function
 
while
 
the
 
vehicle
 
is
 
towing.
Chapter
 
9,
 
"Identification
 
markings"

 
section.
towing a trailer

Berlingo_2_VP_en_Chap06_Accessoire_ed02-2014
 137
OtHEr AccESSOrIES
These accessories and parts, having
been tested and approved for reliability
and safety, are all adapted to your
vehicle. 
A 
wide   range   of   recommended  
accessories and genuine parts is
available.
a further range is also available,
structured

  around   comfort,   leisure   and  
maintenance:
Anti-theft

  alarm,   window   etching,   first  
aid

  kit,   high   visibility   vest,   front   and  
rear

  parking   sensors,   warning   triangle,  
security

  bolts   for   alloy   wheels,   ...
Seat
  covers   compatible   with   airbags  
for the front seats, bench seat, rubber
mats,

 
carpet
 
mats,
 
snow
 
chains,
 
blinds,
 
tailgate

  bicycle   carrier,   ...
To
  prevent   the   mat   from   becoming  
caught

  under   the   pedals:
-
 
ensure
  that   the   mat   and   its   fixings  
are positioned correctly

,
-
 
never
  fit   one   mat   on   top   of   another.Audio
  equipment,   hands-free   kit,
 speakers,
  CD   changer,   satellite navigation
 system,  USB  box,  V ideo  kit,  ...
Regardless
  of   the   audio   and   telematic
 equipment

  offered   on   the   market,   the
 technical constraints associated with


the
  fitting   of   equipment   of   these   product
 groups

  mean   that   the   special   features
 of

  the   equipment   and   its   compatibility
 with the capacities of your vehicle's


standard
  equipment   must   be   taken   into
 account.

  Please   ask   a   CITROËN   dealer
 for

  more   information   before   fitting   such
 equipment.
Maximum weights on bars
-


T
ransverse bars on longitudinal
bars:
  75   Kg   (these   bars   are   not  
compatible

  with   the   Modutop   roof).Installing radiocommunication
transmitters
You are advised to contact a CITR
o Ë n
dealer before installing accessory
radiocommunication
  transmitters   with  
external

  aerial   on   your   vehicle.
The
  CITROËN dealer   network  
will

  inform   you   of   the   specification  
(frequency

  band,   maximum   output  
power

,   aerial   position,   specific  
conditions of installation) of the
transmitters

  which   can   be   fitted,   in  
accordance with the Motor V

ehicle
Electromagnetic
  Compatibility  
Directive
  (2004/104/EC).
Front
  mud   flaps,   rear   mud   flaps,  
15/17 inch

  alloy   wheels,   wheelarch  
trim,

  leather   steering   wheel,   ...
Screenwash, interior and exterior
cleaning
  and   maintenance   products,  
spare

  bulbs,   ...
Equipment
AccESSOrIES
6

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
164
FIttInG tHE WHEEL trIM
The tyre valve must be centred in the wheel
  trim   cut-out.
This
  position   is   essential   for   fitting   the  
wheel

  trim   correctly   on   the   steel   wheel.  
(If

the valve is not correctly aligned with
the
  cut-out,   the   anti-rotation   system  
will be in contact with the heads of the
wheel

  bolts   and   risks   being   damaged  
if

  the   user   persists   in   fitting   the   wheel  
trim

  in   this   incorrect   position). -

Ensure that all of the clips are
engaged except the last one
(opposite

  the   valve   hole).
-
 
Strike
  the   wheel   trim   with   the   palm  
of your hand, opposite the valve
in

  the   area   of   the   last   fixing   clip  
(always

  in   the   direction   of   clipping).
-

Ensure that the outer edge of
the

  wheel   trim   is   not   deformed   or  
pushed

  into   the   wheel.
●
 c
orrect position for the edge of
the
  wheel   trim.
●
 
Incorrect
position for the edge of
the
  wheel   trim.
6. refitting the repaired
wheel
The wheel is refitted as described in step   5,   not   forgetting   to   refit   the   wheel  
trim.
Refer

  to   the   "Instruments   and  
controls" section of chapter 3,
"T

yre   under-inflation   detection"  
part,

  for   recommendations   after  
changing

  a   wheel   fitted   with   a   tyre  
under-inflation

  detection   sensor.
Refer
  to   the   "Identification  
markings"

  section   of   chapter   9   to  
locate

  the   tyre   label.
The spare wheel is not designed
to
  be   used   over   long   distances.  
Have the tightening of the bolts
and

  the   tyre   pressure   checked   by  
a

  CITROËN   dealer   or   a   qualified  
workshop

  as   soon   as   possible.
Have the original wheel repaired
and
  refitted   by   a   CITROËN   dealer  
or

  a   qualified   workshop   as   soon   as  
possible.
Changing a wheel

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
174
dASHBOArd FuSES
Tilt the cover to gain access to the
fuses.Fuses
F Amperes  Aa
llocation
1 15 Rear wiper
2 - Spare
3 5
a

irbag
4 10 Air
  conditioning,   diagnostic   socket,   mirror   control,  
headlamp

  beam
5 30 Electric windows
6 30Locks
7 5Rear
  courtesy   lamp,   front   map   reading   lamp,   roof  
console
8 20 Audio

  equipment,   screen,   tyre   under-inflation  
detection,

  alarm   and   siren
9 30Front
  and   rear   12V   socket
10 15 Central
  column
11 15 Low current ignition switch
12 15 Rain and sunshine sensor, airbag
13 5 Instrument
  panel
14 15 Parking
  sensors,   digital   air   conditioning   controls,  
hands-free

  phone   kit
15 30 Locks
16 - Spare
17 40Rear
  screen/mirrors   demist/defrost
Changing a fuse

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
176
FuSES undEr tHE BOnnEt
after opening the bonnet, unclip and tilt
the corresponding box to gain access
to
  the   fuses. Fuses
F Amperes  Aa
llocation
1 20 Engine
  management
2 15 Horn
3 10 Front
  and   rear   wash-wipe   pump
4 20 Headlamp
  wash   pump
5 15 Engine
  components
6 10 Steering wheel angle sensor,
d SC
7 10Brake
  switch,   clutch   switch
8 25 Starter
9 10Headlamp
  beam   motor,   parc   management   unit
10 30 Engine
  components
11 40 Spare
12 30 Wipers
13 40 Built-in
  systems   interface
14 30 Pump
15 10 Right-hand
  main   beam   headlamp
16 10Left-hand
  main   beam   headlamp
17 15Right-hand
  dipped   beam   headlamp
18 15 Left-hand
  dipped   beam   headlamp
Changing a fuse