change wheel Citroen BERLINGO MULTISPACE RHD 2017 2.G User Guide

175
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
4. Removing the wheel with punctured tyre
- Position  the   foot   of   the   jack   on   the  ground and ensure that it is directly
below
  the   front   or   rear   jacking  
point provided on the underbody

,
whichever is closest to the wheel to
be
  changed.
-
 
Extend
  the   jack   until   its   head  
comes

  into   contact   with   the   jacking  
point used; the vehicle's contact
area

A must be engaged with the
head
  of   the   jack.
-

Raise the vehicle until there is
sufficient

  space   between   the   wheel  
and the ground, so that the (not
punctured) spare wheel can be
easily

  fitted.
-

Resume and complete the
unscrewing

  of   the   wheel   bolts.
-

Remove the bolts and remove the
wheel.
-

 Remove
 
the
 
wheel
 
trim.
-

Loosen the wheel bolts and start
unscrewing

 
them. Ensure
  that   the   jack   is   stable,   the   foot  of
  the   jack   must   be   in   contact   with   the  
ground,

  and   directly   below   the   jacking  
point

  used.
If the ground is slippery or loose, the
jack
  may   slip   or   drop   -   Risk   of   injury!
Ensure
  that   the   jack   is   positioned   only  
at

  one   of   the   jacking   points   under   the  
vehicle,

  making   sure   that   the   vehicle's  
contact surface is centred on the head
of

  the   jack.
Otherwise
  there   is   a   risk   of   damage  
to

  the   vehicle   and/or   of   the   jack  
dropping -

  Risk   of   injury!
Do
  not   extend   the   jack   until   you   have  
started unscrewing the bolts on the
wheel to be changed and have placed
the

  chock   under   the   wheel   diagonally  
opposite.
QUICK HELP
8
Changing a wheel

183
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
3. Direction indicators
Type B, PY21W - 21W (amber)
-
Remove the cover by pullin
g the
flexible
  rubber   tab.
-

T
urn the bulb holder a quarter turn
anticlockwise.
-

Remove the bulb by pressing it
lightly

  while   turning   it   anticlockwise.
-
 
Change
  the   bulb.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure correct
sealing. 4. Front foglamps
T

ype C, H1 - 55W
-

Remove the three clips and the
screw securing the wheel arch liner

,
located
  below   the   bumper.
-
 
Move
  the   wheel   arch   liner   upwards.
-

Disconnect the bulb holder
connector by pressing the tab at
the

  top.-

Remove the bulb holder by
squeezing the two clips (at top and
bottom)

  using   a   finger   and   thumb.
-

Replace the module (bulb holder
and

  bulb).
-

Carry out the operations in reverse
order

  to   fit   the   module   and   refit   the  
wheel

  arch   liner.
QUICK HELP
8
Changing a bulb

185
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
Rear lamps
This procedure requires the use of
the spanner supplied with the tools for
changing  a   wheel.
When
  refitting,   take   care   to  
reposition the tabs and the wiring
correctly to avoid trapping the
wiring.
After changing the rear direction
indicator bulb, the reinitialisation time is
above

  2   minutes.
-
Move aside the 4 tabs then extract
the
  bulb   holder.
-

Remove the faulty bulb by
pressing it lightly while turning it
anticlockwise.
-

 
Change
  the   bulb.
When
  removing   the   lamp   unit:
-

with tailgate, pull the lamp unit
towards the centre of the vehicle,
-


with hinged doors, pull the lamp
unit

  towards   you.
For more information on bulbs, refer to
the
 
"Types
 
of
 
bulb".
1.

Brake lamps / sidelamps


T

ype B,
 
P21/5W
 
-
 
21/5W
2.

Direction indicators


T

ype B, PY21W - 21W (amber)
3.

Reversing lamps


T

ype B, P21W - 21W
4.

Foglamps


T

ype B, P21W - 21W
High pressure jet washing When using this type of washing
on stubborn dirt, do not persist on
the headlamps, the other lamps
and their edges to avoid damaging
their
 
coating
 
and
 
seals. Chapter 9, "Changing a wheel"
section.
-

Identify the failed bulb, then open
the

  rear   doors   to   180°.
Chapter
  3,   "Access"   section.
-
 
Remove
  the   two   fixing   bolts   using  
the

  spanner   provided.
-
 
Pull
  the   lamp   unit   from   the   outside.
-

Holding the lamp, disconnect the
electrical

  connector.
QUICK HELP
8
Changing a bulb