Citroen BERLINGO MULTISPACE RHD 2017 2.G Workshop Manual

49
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
MANUAL GEARBO x
5-speed
6-speed
To change gear easily, always depress
the
 
clutch
 
pedal   fully.
To prevent the mat from becoming
caught
 
under
 
the   pedal:
-

ensure that the mat is positioned
and

 
secured   correctly   on   the   floor,
-
 
never

 
fit
 
one   mat   on   top   of   another.
When driving, avoid leaving your hand
on
 
the
 
gear
 
knob   as   the   force   exerted,  
even if slight, may wear the internal
components

 
of
  the   gearbox   over   time.
Changing into 5th or 6th gear
To engage the gear correctly, move the
gear  lever   fully   to   the   right.
Engaging reverse gear
The lever should be moved slowly
to  reduce   noise.
To engage reverse gear, wait until the
vehicle
  has   come   to   a   complete   stop.
STEERING WHEEL ADJUSTMENT
When the vehicle is stationary,
release
  the   steering   wheel   adjustment  
mechanism

  by   pulling   the   lever.
Adjust
  the   steering   wheel   for   height  
and

  reach,   then   lock   the   mechanism   by  
pushing

  the   lever   fully   forward. In
  the   6-speed   configuration,   raise   the  collar
  below   the   gear   knob.
READY TO GO
3
Gearbox and steering wheel

50
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
The information appears
in the instrument panel
in  the   form   of   an   arrow.   It  
may be accompanied by a
recommended

  gear.
The system adapts its gear
change recommendation
according to the driving conditions
(slope,
 
load, ...)   and   the   demands  
of the driver (power

, acceleration,
braking, ...).
The
 
system   never   suggests:
-
 
engaging
  first   gear,
-
 
engaging
  reverse   gear.
With an electronic gearbox, the system
is
 
only
 
active
 
in
 
manual
 
mode.
GEAR SHIFT INDICATOR
Depending on the driving situation and
your vehicle's equipment, the system
may   advise   you   to   skip   one   (or   more)  
gear(s).

 
Y
ou   can   follow   this   instruction  
without engaging the intermediate
gears.
The gear engagement
recommendations must not be
considered

  compulsory.  
This
  is  
because

  the   configuration   of   the   road,  
the

  traffic   density   and   safety   remain  
determining factors when choosing
the

  best   gear.  
Therefore,
  the   driver  
remains responsible for deciding
whether or not to follow the indications
given.
This

  function   cannot   be   deactivated.
System which reduces fuel
consumption by recommending the
most
 
appropriate
 
gear.
Gearbox and steering wheel

51
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
6-SPEED ELECTRONIC GEARBOx
- automatic  mode:   gear   selector   in  position
A.
-
 
manual
  mode:   gear   selector   in  
position

M.
For
  safety:
It is only possible to come out
of position N
  if   the   brake   pedal   is  
pressed.
The change from position

A (driving in
automatic mode) to position M (driving
in manual mode) or vice versa can be
made
  at   any   time.  
The
  warning   lamp   A
goes
  off   in   the   instrument   panel.
Mode selection Moving off
- To start the engine, the gear
selector must be in position N.
-
 
Press
  firmly   on   the   brake   pedal.
-
 
Operate
  the   starter.
-

When the engine is running, place
the gear selector on

R, A or M as
desired.
-
 
Release
  the   brake   pedal   and  
accelerate.
If the gear selector is not in position

N,
and/or
  if   the   brake   pedal   is   not  
pressed,

  the   engine   will   not   start.  
Repeat

  the   above   procedure.
Reverse gear Engaging reverse gear
Move the gear selector to R.
Only attempt to select reverse gear
when the vehicle is stationary.
Neutral Changing to neutral
Move the gear selector to N.
  If   the  
vehicle is moving, do not select this
position

  even   momentarily.
READY TO GO
3
Gearbox and steering wheel

52
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Acceleration
For optimum acceleration (e.g. to overtake  another   vehicle),   simply  
press the pedal beyond the point of
resistance at the end of its travel, by
pressing

  down   firmly.
Vehicle stationary, with the
engine running
In the event of a prolonged stop with
the engine running, the gearbox
changes automatically to neutral N.
Stopping the vehicle
Before stopping the engine, put the
gear selector in position N.
In all cases, it is essential to apply
the  parking   brake.   Check   that   the  
parking

  brake   warning   lamp   is   on   in   the  
instrument

  panel.
Before doing anything in the
engine
  compartment,   check   that  
the gear selector is in neutral

N.
Changing gear
In situations of high engine speeds
(heavy acceleration), a change
up will not occur unless the driver
operates the electronic gearbox control
paddle. Pull on the "+" control
paddle
  to   change   up.
Pull on the "-" control
paddle to change
down.
-

If the vehicle stops or reduces
speed (for example when
approaching a stop sign),
the gearbox changes down
automatically

,   to   first   gear   if  
needed.
-


It is not necessary to release the
accelerator completely during gear
changes.
-


A
gear change instruction is
accepted only if the engine speed
permits.
-

For safety reasons, depending on
the engine speed, a change down
may

  be   performed   automatically.
Manual mode
Changing to manual mode
Move the gear selector to M. Automatic mode Changing to automatic
mode
Move the gear selector to A.
The gearbox then operates in
automatic mode, without any action on
your
 
part.
It constantly selects the gear that is
best
 
suited
 
to
 
the
 
following
 
conditions:
-

driving style,
-

 
road

 
profile,
-
 
optimum

 
fuel
 
consumption.
Gearbox and steering wheel

53
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
STOP & START
The Stop & Start system puts the
engine temporarily on standby - ST OP
mode
  -   during   stops   in   the   traffic   (red  
lights,

  traffic   jams,   or   other...).
The engine restarts automatically -
START mode - as soon as you want to
move
  off.
The
  restart   takes   place   instantly,  
quickly

  and   silently.
Perfect for urban use, the Stop & Start
system reduces fuel consumption and
exhaust emissions as well as the noise
level
  when   stationary.
Operation
Going into engine STOP modeThe "ECO" warning lamp
comes on in the instrument
panel and the engine goes
into
  standby:
-

with a manual gearbox
, at speeds
below
  12   mph   (20   km/h),   when   you  
put the gear lever into neutral and
release the clutch pedal,
-


with a 6-speed electronic
gearbox

, at speeds below 5 mph
(8
  km/h),   when   you   press   the   brake  
pedal or put the gear lever into
position

N. If
  your   vehicle   is   fitted   with   the   system,  
a time counter calculates the sum of
the periods in ST

OP mode during a
journey.   It   rests   itself   to   zero   every   time  
the

  ignition   is   switched   on   with   the   key.
With a 6-speed electronic
gearbox, for your comfort during
parking   manoeuvres,   STOP
 
mode  
is not available for a few seconds after
coming

  out   of   reverse   gear.
STOP mode does not affect the
functionality of the vehicle, such as
braking,   power   steering,   for   example.
Never refuel with the engine in
STOP mode; you must switch off
the   ignition   with   the   key.Special cases: STOP mode
unavailable
STOP
 

mode   is   not   invoked   when:
-
the vehicle is on a steep slope
(rising or fallin

g),
-
the driver's door is open,
-

the driver's seat belt is not
fastened,
-

the vehicle has not exceeded

6   mph   (10   km/h)   since   the   last  
engine

  start   using   the   key,
-
the engine is needed to maintain
a comfortable temperature in the
passenger compartment,
-

demisting is on,
-

some special conditions (battery
charge, engine temperature,
braking

  assistance,   ambient  temperature...)
  where   the   engine  is needed to assure control of a
system.
In this case, the
"ECO"
warning
  lamp   flashes   for   a  
few

  seconds,   then   goes   off.
This operation is perfectly normal.
READY TO GO
3
Stop & Start

54
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Going into engine START modeThe "ECO" warning lamp
goes
  off   and   the   engine   starts:
-

with a manual gearbox
, when you
fully depress the clutch pedal,
-

with a 6-speed electronic
gearbox

:
●
 
gear
  lever   in   position   A or M,
when
  you   release   the   brake  
pedal,
●

 
or
  gear   lever   in   position   N and
the
  brake   pedal   released,   when  
you move the gear lever to
position

A or M,
●
 
or
  when   you   engage   reverse  
gear

.
With a manual gearbox in STOP
mode, if a gear is engaged without
fully depressing the clutch pedal, a
warning lamp comes on or a message
is
  displayed   asking   you   to   depress   the  
clutch

  pedal   to   restart   the   engine.
Special cases: START invoked
automatically
For your safety and comfort, START is
invoked
  automatically   when:
-

you open the driver's door
,
-

you unfasten the driver's seat belt, In this case the

"ECO"
warning
  lamp   flashes   for   few  
seconds,

  then   goes   off.
This operation is perfectly normal.
Deactivation
In certain circumstances, such as the need
to maintain a comfortable temperature in
the passenger compartment, it may be
preferable
  to   deactivate   Stop   &   Start.
At any time, press the "ECO
OFF" switch to deactivate the
system.
This
 
is
 
confirmed   by   the   switch   warning  
lamp coming on accompanied by a
message

  in   the   screen.
If the system has been deactivated
in STOP mode, the engine restarts
immediately.
Reactivation
Press the "ECO OFF" switch again.
The system is active again; this is
confirmed
  by   the   switch   warning  
lamp going of

f and a message in the
instrument
  panel.
The system is reactivated
automatically at every new start
using
  the   key.
Operating fault
In the event of a malfunction
with the system, the "ECO
OFF" switch warning lamp
flashes,  then   comes   on  
continuously

.
This
  system   requires   a   specific  
battery

  with   a   special   specification  
and technology (reference
numbers available from a CITROËN
dealer

 
or
  a   qualified   workshop).
Fitting a battery not listed by
CITROËN introduces
  the   risk   of  
malfunction

  of   the   system.
have
 
it
 
checked   by   a   CITROËN   dealer  
or

 
a
 
qualified   workshop.
In the event of a fault in STOP mode,
the
 
vehicle   may   stall.  
All
  of   the   warning  
lamps in the instrument panel come
on.

 
It
 
is
 
then   necessary   to   switch   off  
the ignition and start the engine again
using

 
the
  key.
-

the speed of the vehicle exceeds
15

 
mph
 
(25
 
km/h)
 
with
 
a
 
manual
 
gearbox

 
or
 
7
 
mph
 
(11
 
km/h)
 
with
 
the 6-speed electronic gearbox
system,
-
some special conditions (battery


charge,
 
engine
 
temperature,
 
braking
 assistance,

 
ambient
 
temperature...)
 where the engine is needed to


assure
 
control
 
of
 
a
 
system.
Stop & Start

55
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
The Stop & Start system
requires  a   battery   of   specific  
characteristics.

 
All
  work   on   this  
type of battery must be done only
by

 
a
  CITROËN   dealer   or   a   qualified  
workshop.
For more information on the 12 V
battery

,   refer   to   "Battery"   in   section   8.
Good practice when stopping Good practice when starting
Diesel pre-heating warning
lamp
If the temperature is high
enough, the warning lamp
comes on for less than
one second, you can start
without
  waiting.
In cold weather, wait for this warning
lamp to go off then operate the starter
(Starting position) until the engine
starts. Door or bonnet open
warning lamp
If this comes on, a door or the bonnet
is
  not   closed   correctly,   check!
Minimise engine and gearbox wear
When switching off the ignition, let the
engine run for a few seconds to allow
the turbocharger (Diesel engine) to
return
  to   idle.
Do not press the accelerator when
switching
  off   the   ignition.
There is no need to engage a gear
after
  parking   the   vehicle.
STARTING AND ST OPPING
Running and accessories position.
To
  unlock   the   steering,   turn   the  
steering wheel gently while turning the
key

,   without   forcing.   In   this   position,  
certain

  accessories   can   be   used.
Starting position.
The starter is operated, the engine
turns
  over,   release   the   key.
STOP position:
  steering   lock.
The
  ignition   is   off.  
T
urn   the   steering  
wheel

  until   the   steering   locks.   Remove  
the

  key.
Opening the bonnet
Before doing anything under the
bonnet, deactivate the Stop & Start
system
 
to
 
avoid
 
the
 
risk
 
of
 
injury
 
related to an automatic change to
ST

ART
 

mode.
Driving on flooded roads
Before
 
driving
 
through
 
a
 
flooded
 
road,
 
it is strongly recommended that you
deactivate

 
the
 
Stop
 
&
 
Start
 
system.
For more advice on driving, particularly
on
 
flooded
 
roads,
 
refer
 
to
 
the
 
corresponding

 
section.
READY TO GO
3
Stop & Start

56
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Starting and switching off
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
HILL START ASSIST
This system (also called HHC - Hill
Holder
  Control),   linked   to   the   dynamic  
stability

  control   system,   makes   hill  
starts easier and is activated in the
following

  conditions:
-

the vehicle must be stationary
,
engine
  running,   foot   on   the   brake,
-

the gradient of the road must be
steeper than 5%,
-


uphill, the gearbox must be in
neutral or in a gear other than
reverse,
-


downhill, reverse gear must be
engaged.
The Hill Start

Assist system is a driving
aid.
  It   is   not   an   automatic   vehicle  
parking

  function   or   an   automatic  
parking

  brake.
Operation
With the brake pedal and clutch pedal pressed, from the time you release
the  brake   pedal,   without   using   the  
parking

  brake,   you   have   approximately  
2

seconds to move off before the
vehicle
  starts   to   roll   back.
During the moving off phase, the
function is deactivated automatically,
gradually
  releasing   the   braking  
pressure.

  During   this   phase,   the  
characteristic noise of mechanical
release

  of   the   brakes   may   be   heard,  
indicating the imminent movement of
the

  vehicle.
Operating fault
Hill start assist is deactivated in the
following   situations:
-

when the clutch pedal is released,
-

 
when
  the   parking   brake   is   applied,
-

when the engine is switched of
f,
-
 
when
  the   engine   stalls.
If a malfunction of the
system occurs, this
warning lamp comes on
accompanied by an audible
signal
  and   confirmed   by  
a

  message   in   the   screen.   Have   the  
system

  checked   by   a   CITROËN   dealer  
or

  a   qualified   workshop.

57
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Starting and switching off
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
DRIVING RECOMMENDATIONS
Observe the driving regulations and
remain  vigilant   whatever   the   traffic  
conditions.
Pay

  close   attention   to   the   traffic   and  
keep

  your   hands   on   the   wheel   so   that  
you are ready to react at any time to
any

  eventuality.
As a safety precaution, the driver
must only carry out actions requiring
sustained attention when the vehicle is
stationary.
On
  a   long   journey,   a   break   every  
two hours

  is   strongly   recommended.
In
  difficult   weather,   drive   smoothly,  
anticipate

  the   need   to   brake   and  
increase the distance from other
vehicles.
Driving on flooded roads
We strongly advise against driving
on  flooded   roads,   as   this   could   cause  
serious damage to the engine or
gearbox, as well as to the electrical
systems

  of   your   vehicle. If you are obliged to drive through
water:
-
 
check
  that   the   depth   of   water   does  
not

  exceed   15   cm,   taking   account  
of waves that might be generated
by other users,
-

deactivate the Stop & Start system,
-

drive as slowly as possible without
stallin

g.   In   all   cases,   do   not   exceed  6
  mph   (10   km/h),
- do not stop and do not switch of f
the
  engine.
On
  leaving   the   flooded   road,   as   soon  
as

  circumstances   allow,   make   several  
light

  brake   applications   to   dry   the   brake  
discs

  and   pads.
If in doubt on the state of your vehicle,
contact a CITROËN dealer or a
qualified
  workshop.Never
  drive   with   the   parking   brake  
applied

  -   Risk   of   overheating   and  
damage

  to   the   braking   system!
Risk   of   fire!
As the exhaust system of your vehicle
is very hot, even several minutes
after switching off the engine, do not
park   or   leave   the   engine   running   over  
areas

  where   inflammable   substances  
and

  materials   are   present:   grass,  
leaves, etc.
Never leave a vehicle
unsupervised with the engine
running.
  If   you   have   to   leave  your vehicle with the engine running,
apply
  the   parking   brake   and   put   the  
gearbox into neutral or position

N or P,
depending
  on   the   type   of   gearbox.
Important!
READY TO GO
3

58
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
DIRECTION INDICATORS
"Motorway" function
Press  the   control   up   or   down   to   flash  
the corresponding direction indicator
three

  times.
LIGHTING
Left: downwards passing the point  of   resistance.
Right:
  upwards   passing   the  
point

  of   resistance.
Front and rear lighting
Lighting off
Automatic illumination of
headlamps
Sidelamps
Dipped beam (green)
Dipped beam/main beam change
Pull
 
the
 
stalk   fully   towards   you.
Lighting-on audible warning
On switching off the ignition, all of the
lamps turn off, except dipped beam if
automatic guide-me-home lighting has
been
 
activated.
 Checking

 
by
 
means
 
of
 
the
 
indicator
 lamps in the instrument panel is


described in the "Instruments and
controls"
 
section
 
of
 
chapter
 
3.
Direction indicators
Selection is by turning this
ring. Main beam (blue)
To activate the lighting
control, turn this ring to
the lighting off position "0"
then to the selection of
your   choice.
On opening the driver's door, there is
an audible warning if you have left the
lighting
  on.
Steering mounted controls