ignition CITROEN C CROSSER 2010 Owners Manual
Page 3 of 217
I
M O N I T O R I N G
21
Warning
lamp is on Cause Actions/Observations
Diesel
preheating Fixed This comes on when the
ignition switch is in the
ON position. Wait until this goes off before starting.
The duration for which this is on is determined
by the exterior climatic conditions.
Parking brake/ B r a k e fl u i d level Fixed This comes on for a few
seconds when the ignition
is turned to "ON" then
goes off.
It is accompanied by a message on the
instrument panel screen.
The parking brake is
applied or has not been
released fully. It is accompanied by a message on the
instrument panel screen. Release the parking
brake to switch off the warning lamp.
T h e b r a k e fl u i d l e v e l i s
too low. It is accompanied by a message on the
i n s t r u m e n t p a n e l s c r e e n . T o p u p w i t h b r a k e fl u i d
and contact a CITROËN dealer.
Emission
control system Fixed or
fl a s h i n g T h i s c o m e s o n o r fl a s h e s
if the system fails. Consult a CITROËN dealer.
It should go off a few seconds after starting the
engine.
Battery charge Fixed This comes on if a
charging circuit fault
occurs. It should go off when the engine is started.
It is accompanied by a message on the
instrument panel screen. Check the battery
terminals (refer to the "Battery" section).
Page 4 of 217
I
M O N I T O R I N G
22
Warning
lamp is on Cause Actions/Observations
Driver's
seat belt not fastened Fixed The driver has not
fastened or has
unfastened their seat belt. This is accompanied by a message on the
instrument panel screen.
Fasten the driver's seat belt.
ABS Fixed
This comes on if an
anti-lock braking system
fault occurs. It is accompanied by a message on the
instrument panel screen. The vehicle retains
conventional braking without assistance but
you are advised to stop. Have it checked by a
CITROËN dealer.
Airbags and
pretensioners Fixed This comes on for a few
seconds when the ignition
is turned to "ON" then
goes off.
It should go off when the engine is started. If it
d o e s n o t g o o f f , c o n t a c t a C I T R O Ë N d e a l e r .
This comes on if an
airbag or pretensioner
fault occurs. It is accompanied by a message on the
instrument panel screen. Have the system
checked by a CITROËN dealer without delay.
Dynamic
stability control system (ASC) Fixed This comes on if a
dynamic stability control
system fault occurs. It is accompanied by a message on the
instrument panel screen. Have the system
checked by a CITROËN dealer without delay.
Page 5 of 217
I
M O N I T O R I N G
23
E a c h t i m e t h e e n g i n e i s s t a r t e d : a s e r i e s o f w a r n i n g l a m p s a n d / o r m e s s a g e s c o m e o n , a p p l y i n g a c h e c k i n g s e l f t e s t . T h e y g o
off after a few seconds. Engine running: the warning lamp o r the message becomes a warning if it remains on continuously
o r fl a s h e s . T h i s i n i t i a l w a r n i n g m a y b e a c c o m p a n i e d b y a n a u d i b l e s i g n a l a n d a m e s s a g e o n t h e s c r e e n . D o n o t i g n o r e t h e s e
warnings.
The messages displayed may differ between the type 1 instrument panel and the type 2 instrument panel.
W h e n t h e c a u s e o f t h e a p p e a r a n c e o f t h e w a r n i n g l a m p o r w a r n i n g m e s s a g e h a s b e e n r e c t i fi e d , t h e w a r n i n g d i s a p p e a r s
f r o m t h e s c r e e n a u t o m a t i c a l l y . I f t h e c a u s e o f t h e w a r n i n g i s n o t r e c t i fi e d , y o u c a n r e t u r n t o t h e p r e v i o u s s c r e e n a t a n y t i m e
by pressing the INFO button on the dashboard.
The symbol "!" is displayed.
To return to the previous screen (with the "!" s y m b o l ) , y o u m u s t p r e s s t h e INFO button several times.
Warning messages (ignition at "OFF")
You can close the warning messages which show these symbols in ord er to move on to the next screen.
T o d o t h i s , p r e s s t h e INFO button according to the symbol displayed.
Press b r i e fl y . Press and hold .
S y m b o l s w h i c h a p p e a r i n t h e t o p r i g h t c o r n e r o f t h e s c r e e n .
Message is on Cause Solution - action Observations
K e y i n
ignition Fixed The driver's door is open
and you have forgotten
to remove the key from
the ignition. Turn the ignition switch
to the LOCK position
and remove the key. Only if the engine has
been started.
An intermittent audible
signal is heard.
Lighting
l e f t o n Fixed You have forgotten to
switch off the vehicle
lighting. Switch off the vehicle
lighting by placing the
stalk at OFF.
An intermittent audible
signal is heard.
Page 6 of 217
I
M O N I T O R I N G
24
Warning messages (ignition at "ON")
Message is on Cause Solution - action Observations
ABS Fixed Anti-lock braking system
(ABS) fault. Consult a CITROËN
dealer. The vehicle retains
conventional braking
without assistance
but you are advised
to stop.
Braking system Fixed Associated warning
lamp.
The level of brake
fl u i d i n t h e r e s e r v o i r
is too low.
S t o p a n d t o p u p , o t h e r w i s e
contact a CITROËN dealer.
If the message
remains on after
t o p p i n g u p , c o n t a c t
a CITROËN dealer.
Associated warning
lamp.
Braking system fault. Consult a CITROËN
dealer.
You must
stop.
Parking
brake on Fixed You have moved off with
the parking brake still
applied. Release the parking brake.
Coolant
temperature Flashing
High engine temperature. If the message
fl a s h e s ,
wait for the engine to cool
b e f o r e t o p p i n g u p t h e l e v e l ,
if necessary.
You must
stop
y o u r v e h i c l e
as
soon as it
is
s a f e
to
do so
.
Flashing If the message
fl a s h e s and the
s e r v i c e w a r n i n g l i g h t
comes on , c o n t a c t
a CITROËN dealer
without delay.
Seat belt Fixed The driver has not fastened
or has unfastened his seat
belt. Fasten your seat belt. There is an
intermittent audible
signal above 5 mph
(8 km/h).
Page 10 of 217
I
M O N I T O R I N G
28
Prevention messages
I n f o r m a t i o n m e s s a g e s ( i g n i t i o n a t " O N " )
Message is on S t a t u s o f t h e s y s t e m
2WD two wheel drive system Flashing When the "2WD" (2 wheel drive) mode is selected using the
transmission mode selector.
4WD four wheel drive system Flashing When the "4WD" (4 wheel drive) mode is selected using the
transmission mode selector.
This mode is the default mode.
4WD LOCK four
wheel drive system Flashing When the "LOCK" (4 wheel drive) mode is selected using the
transmission mode selector.
Ambient
temperature Fixed This indicates the ambient temperature.
When the vehicle is stationary or if the speed is b
elow 12 mph
(20 km/h) the temperature displayed may not be the true temperature.
D i s p l a y is on Cause Solution - action Observations
Service
indicator Fixed Informs the driver of
the time remaining
before the vehicle's
scheduled service. Consult a CITROËN
dealer.
This is displayed for a
few seconds when the ignition
is switched on.
Break
advised Fixed Informs the driver that
they should stop to
take a break. You are advised to
take a break. This is displayed when the
driving time that you set
previously is reached.
An audible signal is heard
3 times and is then heard every
5 minutes until the vehicle
stops.
Page 13 of 217
I
M O N I T O R I N G
31
SERVICE INDICATOR Resetting the service indicator to zero
Your CITROËN dealer carries out this
operation after each service.
If you have carried out your vehicle's
s e r v i c e y o u r s e l f , t h e z e r o r e s e t p r o c e -
dure is the following:
switch off the ignition.
press the INFO button several times
in succession until the service indi-
cator is displayed.
press and hold the INFO button for
a few seconds until the spanner
fl a s h e s .
press the INFO button while the
s p a n n e r i s fl a s h i n g t o c h a n g e t h e d i s -
play "---" to "CLEAR" then the time
remaining before the next service is
due is displayed.
Service overdue
Operation
W h e n t h e i g n i t i o n i s s w i t c h e d o n , y o u
must press the INFO button several
times in succession until the service
indicator is displayed. The distance re-
corder display line indicates the number
of miles (kilometres) remaining and the
time elapsed line indicates the number
of months remaining before the next
service is due.
After a certain distance and a certain
t i m e , t h e d i s p l a y o f "---" is reinitialised
and the display indicates the time
remaining before the next service is
due.
System which informs the driver when
the next service is due in accordance
with the manufacturer's servicing
schedule.
The point at which the next service is
due is calculated from the last service
indicator zero reset.
It is determined by two parameters:
- t h e d i s t a n c e t r a v e l l e d ( i n m i l e s ( k m ) ) ,
- the time elapsed since the last service
(in months).
The distance remaining to be travelled
m a y b e w e i g h t e d b y t h e t i m e f a c t o r ,
depending on the user's driving habits.
Example: the display indicates that
7 300 miles (kilometres) remain before
the next service is due.
The symbol "--" remains displayed
u n t i l t h e fi r s t s e r v i c e o f a n e w v e h i c l e
has been carried out.
Example: the display indicates that the
service is overdue. This service must
be carried out by a CITROËN dealer.
E a c h t i m e t h e i g n i t i o n i s s w i t c h e d o n ,
the display
"
PERIODIC INSPECTION
"
is displayed for a few seconds to
indicate that the service must be carried
out without delay.
Page 15 of 217
I
M O N I T O R I N G
31
SERVICE INDICATOR Resetting the service indicator to zero
Your CITROËN dealer carries out this
operation after each service.
If you have carried out your vehicle's
s e r v i c e y o u r s e l f , t h e z e r o r e s e t p r o c e -
dure is the following:
switch off the ignition.
press the INFO button several times
in succession until the service indi-
cator is displayed.
press and hold the INFO button for
a few seconds until the spanner
fl a s h e s .
press the INFO button while the
s p a n n e r i s fl a s h i n g t o c h a n g e t h e d i s -
play "---" to "CLEAR" then the time
remaining before the next service is
due is displayed.
Service overdue
Operation
W h e n t h e i g n i t i o n i s s w i t c h e d o n , y o u
must press the INFO button several
times in succession until the service
indicator is displayed. The distance re-
corder display line indicates the number
of miles (kilometres) remaining and the
time elapsed line indicates the number
of months remaining before the next
service is due.
After a certain distance and a certain
t i m e , t h e d i s p l a y o f "---" is reinitialised
and the display indicates the time
remaining before the next service is
due.
System which informs the driver when
the next service is due in accordance
with the manufacturer's servicing
schedule.
The point at which the next service is
due is calculated from the last service
indicator zero reset.
It is determined by two parameters:
- t h e d i s t a n c e t r a v e l l e d ( i n m i l e s ( k m ) ) ,
- the time elapsed since the last service
(in months).
The distance remaining to be travelled
m a y b e w e i g h t e d b y t h e t i m e f a c t o r ,
depending on the user's driving habits.
Example: the display indicates that
7 300 miles (kilometres) remain before
the next service is due.
The symbol "--" remains displayed
u n t i l t h e fi r s t s e r v i c e o f a n e w v e h i c l e
has been carried out.
Example: the display indicates that the
service is overdue. This service must
be carried out by a CITROËN dealer.
E a c h t i m e t h e i g n i t i o n i s s w i t c h e d o n ,
the display
"
PERIODIC INSPECTION
"
is displayed for a few seconds to
indicate that the service must be carried
out without delay.
Page 16 of 217
I
M O N I T O R I N G
32
TRIP COMPUTER A v e r a g e f u e l consumption(l/100 km or km/lor mpg)
This is the average fuel
consumption since the
last zero reset.
T h i s fi g u r e m a y c h a n g e f o l l o w i n g a
change in the style of driving or the
relief resulting in a change in the
current fuel consumption.
Average speed(km/h or mph)
This is the average
speed calculated since
the last zero reset.
R e s e t t i n g t h e i n f o r m a t i o n t o z e r o
W h e n t h e i g n i t i o n i s s w i t c h e d o n , t h e
zero reset switches automatically from
manual mode to automatic mode.
If dashes "---" are displayed for long
periods in place of the digits while
d r i v i n g , c o n t a c t a C I T R O Ë N d e a l e r .
C u r r e n t f u e l consumption(l/100 km or km/lor mpg)
This is the average fuel
consumption during the last
few seconds of driving.
I n f o r m a t i o n d i s p l a y
W i t h t h e i g n i t i o n o n , p r e s s t h e INFO
b u t t o n o n t h e d a s h b o a r d , t o t h e r i g h t
o f t h e i n s t r u m e n t p a n e l , s e v e r a l t i m e s
in succession to display the different
information:
- a v e r a g e f u e l c o n s u m p t i o n ,
- a v e r a g e s p e e d ,
- current fuel consumption. W h e n t h e r e q u i r e d i n f o r m a t i o n i s
d i s p l a y e d , p r e s s t h e
INFO button for
more than two seconds to reset all of
the information to zero.
Automatic
If the ignition key remains in the OFF
p o s i t i o n f o r m o r e t h a n 4 h o u r s , t h e i n -
formation is reset to zero automatically.
Page 17 of 217
I
!
M O N I T O R I N G
33
When the vehicle is
s t a t i o n a r y , i t a l l o w s
the user to change the
following settings:
- resetting average fuel consumption
a n d a v e r a g e s p e e d ,
- t h e f u e l c o n s u m p t i o n u n i t s ,
- t h e t e m p e r a t u r e d i s p l a y u n i t s ,
- t h e d i s p l a y l a n g u a g e ,
- activation/deactivation of the INFO
b u t t o n s o u n d ,
- the break (rest) reminder display i n t e r v a l ,
- restore factory settings.
SETTING MENU
System which provides access to the
settings of certain functions.
T o c h a n g e t h e s e t t i n g s , y o u
must stop the vehicle and switch
on the ignition.
Apply the parking brake and place
the gear lever in neutral.
When the vehicle is moving , t h e
setting menu screen is not displayed
when you press the INFO button.
The various menus may differ for the
type 1 instrument panel and the type 2
instrument panel.
With the ignition on , p r e s s t h e INFO
b u t t o n o n t h e d a s h b o a r d , t o t h e r i g h t o f
t h e i n s t r u m e n t p a n e l , s e v e r a l t i m e s i n
succession until the "SETTING MENU"
screen is displayed.
Operation
press and hold the INFO button for
a few seconds to display the menu
screen.
Press and hold the INFO button
for a few seconds to return to the
previous screen.
When the menus screen is dis-
p l a y e d , i f n o o p e r a t i o n i s c a r r i e d o u t
w i t h i n 1 5 s e c o n d s , t h e s e t t i n g m e n u
screen is displayed.
o n t h e m e n u s c r e e n , p r e s s t h e INFO
button to select a function from the
list:
MENU
2/3:
- a/b (option of displaying a different
language in the instrument panel
s c r e e n a n d t h e n a v i g a t i o n s c r e e n ) ,
- a c t i v a t i o n / d e a c t i v a t i o n o f t h e I N F O
button sound ,
- ALARM
(changing the "BREAK
R E M I N D E R " d i s p l a y i n t e r v a l ) ,
- choice of the direction indicators s o u n d ,
- a c t i v a t i o n / d e a c t i v a t i o n o f
current
f u e l c o n s u m p t i o n ,
MENU
1/3
:
- 1 - 2 (options for resetting aver-
age fuel consumption and average
s p e e d ) ,
- UNIT (choice of the fuel consump-
t i o n u n i t s ) ,
- choice of the t e m p e r a t u r e d i s p l a y
unit
s ,
- LANGUAGE (choice of display lan-
g u a g e ) ,
MENU 3/3:
- RESET
(restore factory settings).
Page 22 of 217
I
M O N I T O R I N G
38
Set the time using the buttons as
indicated below:
with the ignition on or in the ACC
( A c c e s s o r i e s ) p o s i t i o n , p r e s s a n d
hold the CLOCK button until the
t i m e d i s p l a y fl a s h e s .
Press the appropriate button to set
the time:
Button
H: to set the hours
The hours digits scroll when you press
this button.
Button M: to set the minutes
The minutes digits scroll when you
press this button.
Button 00: to reset the minutes to
zero.
- from 1 to 29 min
: rounded down to
t h e p r e v i o u s h o u r ,
- from 30 to 59 min: rounded up to
the next hour.
Manual mode
Automatic mode
I n t h i s m o d e , s e t t i n g i s a u t o m a t i c u s i n g
the signal from the RDS radio stations.
A f t e r s e t t i n g t h e t i m e , p r e s s t h e
DISP button; the time display stops
fl a s h i n g .
The digital clock does not display
seconds.
When the "minutes" display is set or
r e s e t t o z e r o , t h e c l o c k s t a r t s a t t h e
zero second of the minute selected.
The time setting is lost if the battery
is disconnected.
Turn button B "TUNE" to the left or
to the right to select "CT ON" (auto-
matic mode) or "CT OFF" (manual
mode).
A f t e r s e l e c t i n g t h e m o d e , y o u c a n
exit the "Functions setting mode"
menu by pressing button B "TUNE"
for approximately 2 seconds.
If no action is carried out within
1 0 s e c o n d s , t h e s y s t e m w i l l e x i t
the "Functions setting mode" menu
automatically.