boot CITROEN C-ELYSÉE 2017 Handbook (in English)

63
Storage box
F Raise the boot floor to access the storage box.
This has areas for the storage of a box of spare
bulbs, a first aid kit, two warning triangles...
It also houses the vehicle tools, the temporary
puncture repair kit...
Mats
Removable carpet protection.
Fitting
When fitting the mat for the first time, on the
driver's side use only the fixings provided in the
wallet attached.
The other mats are simply placed on the
carpet.
Removing
To remove the mat on the driver's side:
F M ove the seat as far back as possible.
F

U
nclip the fixings.
F

R
emove the mat.
Fitting
To refit the mat on the driver's side:
F P osition the mat correctly.
To avoid any risk of jamming the pedals:
-

O
nly use mats which are suited to the
fixings already present in the vehicle;
these fixings must be used.
-

D
o not fit one mat on top of another.
The use of mats not approved by
CITROËN
may inter fere with access to the pedals
and hinder the operation of the cruise
control / speed limiter.
F

R

efit the fixings by pressing.
F

C

heck that the mat is secured correctly.
3
Ease of use and comfort

67
Headlight beam height adjustment
To avoid causing a nuisance to other road
users, the height of the headlight beams should
be adjusted according to the load in the vehicle.
Depending on the version, this adjustment can
be carried out using the control located:
-
U
nder the bonnet.
-

T
o the left of the steering wheel
Bonnet
F Raise the bonnet to access the control (one per headlight).
F

T
urn the control to adjust the height of the
headlight beam.
To the left of the steering wheel
0 1 or 2 people in the front seats.
- 5 people.
1 5 people + maximum authorised load in
the boot.
- Driver on his own + maximum authorised
load in the boot.
The higher number positions can be used, but
may limit the area illuminated by the headlights.
The initial setting is position "0". Travelling abroad
The design of the dipped beam headlights
allows, without modification, driving in a
country that drives on the other side of the
road to the country in which your vehicle
was sold.
4
Lighting and visibility

135
F Get a bottle of AdBlue®. After first
checking the use-by date, read carefully
the instructions on use on the label before
pouring the contents of the bottle into your
vehicle's AdBlue
® tank.
Important: if your vehicle's AdBlue
® tank is
completely empty - which is confirmed by
the alert displays and the impossibility of
starting the engine - you must add at least
3.8 litres (so two 1.89 litre bottles). F

A
fter emptying the bottle, wipe away any
spillage around the tank filler using a damp
cloth.
If any additive is spilt or splashed, wash
immediately with cold water or wipe with a
damp cloth.
If the additive has crystallised, clean it off
using a sponge and hot water.
F
R
efit the blue cap to the tank and turn it a
6
th of a turn clockwise, to its stop.
F
R
eplace the plastic valve, clipping it in the
opening.
F

R

eturn the storage box containing the tools
to its location.
F

R

eplace the boot floor and close the boot. Never dispose of AdBlue® additive
bottles in the household waste. Place
them in a container provided for this
purpose or take them to your dealer.
Once the AdBlue tank has been filled,
make sure that the driver as well as the
passengers exit the vehicle, then lock it.
After a minimum delay of 5 minutes
without opening it, unlock the vehicle and
switch the ignition on without starting.
After a minimum of 10 seconds, start the
vehicle.
7
Practical information

149
Temporary puncture repair kit
Comprising a compressor and a sealant
cartridge, it allows the temporary repair of
a tyre so that you can drive to the nearest
garage.
It is designed to repair most punctures which
could affect the tyre, located on the tyre tread
or shoulder.Access to the kit
The vehicle's electric system allows the
connection of the compressor for long
enough to inflate a tyre after a puncture
repair.
This kit is installed in the storage box, under
the boot floor.
Composition of the kit
Do not exceed a speed of 50 mph
(80
km/h) when driving with a tyre repaired
using this type of kit.
1.
12 V compressor, with built-in pressure
gauge.
2. Bottle of sealant, with with built-in hose.
3. Speed limit sticker.
The speed limit sticker must be secured
to the interior of the vehicle in the driver's
field of vision, to remind you that a wheel
is in temporary use.
8
In the event of a breakdown

154
Spare wheel
Procedure for replacing a damaged wheel with the spare wheel, using the tools provided with the vehicle.
Access to the tools
The tools are installed in the boot under the
f l o o r.
To gain access to it:
F
O
pen the boot.
F

L
ift the floor and remove it.
F

R
emove the storage box containing the
tools.
List of toolsThese tools are specific to your vehicle and
may vary according to the level of equipment.
Do not use them for any purpose other than
those detailed below.
1 Wheel wrench.
For removing the hub cap and removing
the wheel bolts.
2 Jack with built-in handle.
Used to raise the vehicle.
3 Wheel bolt cover removal tool.
Removes the wheel bolt covers on alloy
wheels.
4 Towing eye.
For more information on Towing the vehicle ,
refer to the corresponding section.
The jack must only be used to change
a wheel with a damaged or punctured tyre.
The jack does not require any
maintenance.
The jack meets European standards,
as defined in the Machinery Directive
2006/42/EC.
In the event of a breakdown

155
Access to the spare wheel
The spare wheel is installed in the boot, under
t h e f l o o r.
Depending on the engine, the spare wheel is
a standard wheel or the "space-saver" type
(BlueHDi 100).
Removing the wheel
F Unclip the tool storage box (standard spare wheel).
F

L
oosen the central nut.
F

R
emove the fastening device (nut and bolt).
F

R
aise the spare wheel towards you from
the rear.
F

T
ake the wheel out of the boot.
8
In the event of a breakdown

159
F Remove the bolts and store them in a clean place.
F

R
emove the wheel. Stowing the damaged wheel
The damaged wheel can be stowed under
the floor, in the housing for the standard
spare wheel.
To stow an alloy wheel, first remove the
hub cap from the middle of the wheel so
that the fastening device (nut and bolt) can
be put in place.
In the case of a "space-saver" type spare
wheel, the damaged wheel cannot be
stowed under the floor. It must be stowed
in the boot; use a cover to protect the
inside of the boot.
Fitting a wheel
Fastening the spare wheel
If your vehicle is fitted with alloy wheels,
when tightening the bolts on fitting, it is
normal to notice that the washers do not
come into contact with the spare wheel.
The wheel is secured by the conical
contact of each bolt.
After changing a wheel
Do not exceed 50
mph (80 km/h) when
using a "space-saver" type spare wheel.
Have the tightening of the bolts and the
pressure of the spare wheel checked by
a
CITROËN dealer or a qualified workshop
without delay.
Have the punctured wheel repaired and
reinstall it on the vehicle as soon as
possible.
8
In the event of a breakdown

165
Rear lamps
1 Brake / position lamps (P21/5W).
2Direction indicators (PY21W).
3 Reversing lamps (W16W).
4 Fog lamp (P21/5W). These bulbs are changed from inside the boot:
F

O
pen the boot.
F
R
emove the access grille from the
corresponding side trim panel.
F
D
isconnect the lamp connector.
F
L
oosen and remove the nut.
F

F
rom the outside, cautiously remove the
lamp unit straight from its housing. F
R emove the four screws and lift off the bulb
h o l d e r.
F

T
urn the failed bulb a quarter of a turn and
replace it.
For reassembly, carry out these operations in
reverse order.
Take care to engage the lamp unit in its guides,
while keeping it in line with the vehicle.
Tighten sufficiently to ensure sealing, but
without damaging the lamp.
8
In the event of a breakdown

175
Disconnecting the battery
In order to maintain an adequate state
of charge for starting the engine, it is
recommended that the battery be disconnected
if the vehicle is taken out of service for a long
period.
Before disconnecting the battery:
F
C
lose all openings (doors, boot, windows).
F

S
witch off all electricity consuming devices
(audio system, wipers, lighting, etc.).
F

S
witch off the ignition and wait for four
minutes.
After accessing the battery, you only have to
disconnect the (+) terminal.Rapid lock lug
Disconnecting the (+) terminal
F

R
aise palette A as much as possible to
unlock clamp B .
F

R
emove clamp B by raising it. Reconnecting the (+) terminal
F

R
aise palette A as much as possible.
F

R
eplace clamp B open on the (+) terminal
F

P
ress clamp B up to the stop.
F

L
ower palette A to lock clamp B.
8
In the event of a breakdown

177
Towing the vehicle
Procedure for having your vehicle towed.
Access to the tools
The towing eye is installed in the boot under
t h e f l o o r.
To gain access to it:
F
O
pen the boot.
F

L
ift the floor and remove it.
F

R
emove the towing eye from the holder. General recommendations
Observe the legislation in force in your
c o unt r y.
Ensure that the weight of the towing vehicle
is higher than that of the towed vehicle.
The driver must remain at the wheel of the
towed vehicle and must have a valid driving
licence.
When towing a vehicle with all four wheels
on the ground, always use an approved
towing arm; rope and straps are prohibited.
The towing vehicle must move off gently.
When the vehicle is towed with its engine
off, there is no more braking and steering
assistance.
In the following cases, you must always call
on a professional recovery service:
-

v
ehicle broken down on a motor way or
fast road,
-
f
our-wheel drive vehicle,
-
w
hen it is not possible to put the gearbox
into neutral, unlock the steering, or
release the parking brake,
-
t
owing with only two wheels on the
ground,
- w here there is no approved towing arm
available...
8
In the event of a breakdown