engine Citroen C1 DAG 2008.5 1.G User Guide

Page 33 of 99

3
33
COMFORT
1. Air conditioning On/Off With the engine running,
press the button, the indi-
cator lamp comes on.

1. Air conditioning On/Off

2. Temperature adjustment

3. Air fl ow adjustment
AIR CONDITIONING
2. Temperature adjustment
Turn the control from blue (cold) to
red (hot) to adjust the temperature to
suit your requirements.

4. Air recirculation/Air intake

5. Air distribution adjustment

6. Rear screen demisting 3. Air fl ow adjustment
When the ignition is switched on,
turn the control to obtain a fl ow of
air which is suffi cient to ensure your
comfort.
To maintain a certain level of comfort
in the passenger compartment, avoid
position
0 whenever possible.
In position 0 , a slight fl ow of air, due
to the movement of the vehicle, can
still be felt.

The air conditioning will not operate
if the air fl ow adjustment control 3
is in position 0.

Page 34 of 99

3
34
COMFORT Footwells.
4. Air recirculation/Air intake
The recirculation of interior air
(control 4 to the left) enables
you to isolate the passenger
compartment from exterior
odours and smoke. 5. Air distribution adjustment
Windscreen and side windows.
The air distribution can be ad-
justed by placing the control
in an intermediate position. Windscreen, side windows
and footwells.
Footwells, diffusion grille
and side vents.
Diffusion grille and side
vents. 6. Rear screen demisting
As soon as possible, move control 4
to the right to the "Intake of exterior
air" position to avoid the risks of dete-
rioration of the air quality and misting
of the windscreen and side windows. The intake of exterior air
(control
4 to the right) ena-
bles you to prevent and
eliminate misting of the wind-
screen and side windows. With the engine running,
press button
6 , the indicator
lamp comes on.
The system demists the
rear screen.
It is switched off by pressing control 6 .
In a humid climate, use of the
air recirculation may cause
misting of the windows. Switch the system off as
soon as you consider this
necessary as a lower con-
sumption of current reduces
fuel consumption.
Demisting and defrosting
To quickly demist or defrost the wind-
screen and side windows:
- set the air distribution to "Windscreen and side windows",
- place the temperature control 2 and
the air fl ow control 3 at maximum,
- close the side vents,
- place the air intake control 4 in
the "Air intake" position,
- switch on the air conditioning by pressing button 1 .

Page 49 of 99

4
47
ACCESS
IMMOBILISER
This locks the engine control sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
must be recognised for starting to be
possible.
In the event of a malfunction, your
vehicle will not start.
Consult a CITROËN dealer.
Changing the remote control
battery
To change the battery, remove the
screw then unclip the housing using
a coin inserted at the ring.
Battery CR 2016/3 volts.
If the remote control does not work
after the battery has been changed,
reinitialise it.
Reinitialising the remote
control
Following replacement of the remote
control battery or in the event of a re-
mote control malfunction, it may be
necessary to reinitialise the system.

 Switch off the ignition.

 Switch the ignition on again.

 Press one of the remote control
buttons immediately for a few
seconds.

 Switch off the ignition and remove
the key from the ignition lock.
The remote control is now working
again.
If the malfunction persists, contact a
CITROËN dealer. Driving with the doors locked
may make access to the pas-
senger compartment by the
emergency services more
diffi cult in an emergency.
As a safety measure (with children
on board), remove the key from the
ignition when leaving the vehicle,
even for a short time.
Do not make any modifi cations to the
electronic immobiliser system.
Do not discard the remote
control batteries, they con-
tain metals which are harm-
ful to the environment.
Take them to a CITROËN dealership,
or to any other approved collection
point. The high frequency remote control is
a sensitive system; do not operate it
in your pockets as there is a risk that
it may unlock the vehicle without you
being aware of this.
Avoid pressing the buttons of your
remote control out of range of your
vehicle, you risk rendering it inopera-
tive. It would then have to be reini-
tialised.

Page 50 of 99

4
47
ACCESS
IMMOBILISER
This locks the engine control sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
must be recognised for starting to be
possible.
In the event of a malfunction, your
vehicle will not start.
Consult a CITROËN dealer.
Changing the remote control
battery
To change the battery, remove the
screw then unclip the housing using
a coin inserted at the ring.
Battery CR 2016/3 volts.
If the remote control does not work
after the battery has been changed,
reinitialise it.
Reinitialising the remote
control
Following replacement of the remote
control battery or in the event of a re-
mote control malfunction, it may be
necessary to reinitialise the system.

 Switch off the ignition.

 Switch the ignition on again.

 Press one of the remote control
buttons immediately for a few
seconds.

 Switch off the ignition and remove
the key from the ignition lock.
The remote control is now working
again.
If the malfunction persists, contact a
CITROËN dealer. Driving with the doors locked
may make access to the pas-
senger compartment by the
emergency services more
diffi cult in an emergency.
As a safety measure (with children
on board), remove the key from the
ignition when leaving the vehicle,
even for a short time.
Do not make any modifi cations to the
electronic immobiliser system.
Do not discard the remote
control batteries, they con-
tain metals which are harm-
ful to the environment.
Take them to a CITROËN dealership,
or to any other approved collection
point. The high frequency remote control is
a sensitive system; do not operate it
in your pockets as there is a risk that
it may unlock the vehicle without you
being aware of this.
Avoid pressing the buttons of your
remote control out of range of your
vehicle, you risk rendering it inopera-
tive. It would then have to be reini-
tialised.

Page 55 of 99

4
51
ACCESS
FILLING THE FUEL TANK

 Open the fuel fi ller fl ap.

 Insert the key, turn it slightly to
the left then return to the right.
The key returns to its initial posi-
tion and the cap is unlocked.
Low fuel level
When the fuel tank minimum
level is reached, the last
segment fl ashes, accompa-
nied by an audible signal.

You have approximately 5 litres re-
maining.
In certain driving conditions and depend-
ing on the engine, the distance which
can be travelled with the fuel remaining
may be less than 30 miles (50 km).
When the frequency of the fl ashing
increases, you have approximately
3 litres remaining .
 Unscrew the cap and hook it onto
the clip located on the inside of
the fl ap.
A label affi xed on the inside of the
fl ap reminds you which type of fuel
to use.
When you fi ll the fuel tank, do not
continue after the 3rd cut-off of the
pump. This could cause malfunc-
tions.

 Remove the key.

Note : if you run out of fuel,
the emission control system
warning lamp may come on
on the instrument panel. It will
switch off automatically after the en-
gine has been started a few times.
The fuel tank must be fi lled

with the engine switched
off .
The capacity of the fuel tank is ap-
proximately 35 litres.

 After fi lling the fuel tank, screw
the cap back on fully to the right
until it clicks and close the fl ap.

Page 61 of 99

6
56
SAFETY When this warning lamp
comes on, it indicates that
there is a malfunction of the
ABS, which can cause a
loss of control of the vehicle
when braking.
Consult a CITROËN dealer.
When these warn-
ing lamps come
on simultaneous-
ly, it indicates that
there is a malfunc-
tion of the braking system or that the
parking brake has not been released
fully, which can cause a loss of con-
trol of the vehicle when braking.

Stop immediately.
Consult a CITROËN dealer.
Normal operation of the ABS
may make itself felt by slight
vibrations of the brake pedal.

In emergency braking,
press very fi rmly without
releasing the pressure. TRACTION CONTROL (ASR)
AND DYNAMIC STABILITY
CONTROL (ESP)
These systems are linked and sup-
plement the ABS.
The ASR system optimises drive to
prevent the wheels skidding, by act-
ing on the brakes of the driving wheels
and on the engine. It also allows the
directional stability of the vehicle to
be improved on acceleration.
If there is a variation between the tra-
jectory followed by the vehicle and
that required by the driver, the ESP
system automatically acts on the
brake of one or more wheels and on
the engine to put the vehicle back on
course, within the limits of the laws
of physics.
Operating check
Operation of the ASR and ESP
systems When one of these two
systems is operating, this
warning lamp comes on. When a malfunction of the
systems occurs, this warn-
ing lamp comes on.
The ASR/ESP systems offer
exceptional safety during nor-
mal driving, but this should
not encourage the driver to
take extra risks or drive at
high speed.
Correct operation of these systems
depends on observation of the man-
ufacturer's recommendations re-
garding the wheels (tyres and rims),
the braking components and the
electronic components as well as the
CITROËN dealer repair procedures.
After an impact, have these systems
checked by a CITROËN dealer.
Activation of the ESP system is also
accompanied by an audible signal. Contact a CITROËN dealer to have
the systems checked.

Page 62 of 99

6
56
SAFETY When this warning lamp
comes on, it indicates that
there is a malfunction of the
ABS, which can cause a
loss of control of the vehicle
when braking.
Consult a CITROËN dealer.
When these warn-
ing lamps come
on simultaneous-
ly, it indicates that
there is a malfunc-
tion of the braking system or that the
parking brake has not been released
fully, which can cause a loss of con-
trol of the vehicle when braking.

Stop immediately.
Consult a CITROËN dealer.
Normal operation of the ABS
may make itself felt by slight
vibrations of the brake pedal.

In emergency braking,
press very fi rmly without
releasing the pressure. TRACTION CONTROL (ASR)
AND DYNAMIC STABILITY
CONTROL (ESP)
These systems are linked and sup-
plement the ABS.
The ASR system optimises drive to
prevent the wheels skidding, by act-
ing on the brakes of the driving wheels
and on the engine. It also allows the
directional stability of the vehicle to
be improved on acceleration.
If there is a variation between the tra-
jectory followed by the vehicle and
that required by the driver, the ESP
system automatically acts on the
brake of one or more wheels and on
the engine to put the vehicle back on
course, within the limits of the laws
of physics.
Operating check
Operation of the ASR and ESP
systems When one of these two
systems is operating, this
warning lamp comes on. When a malfunction of the
systems occurs, this warn-
ing lamp comes on.
The ASR/ESP systems offer
exceptional safety during nor-
mal driving, but this should
not encourage the driver to
take extra risks or drive at
high speed.
Correct operation of these systems
depends on observation of the man-
ufacturer's recommendations re-
garding the wheels (tyres and rims),
the braking components and the
electronic components as well as the
CITROËN dealer repair procedures.
After an impact, have these systems
checked by a CITROËN dealer.
Activation of the ESP system is also
accompanied by an audible signal. Contact a CITROËN dealer to have
the systems checked.

Page 70 of 99

7
62
DRIVING Driver information
The symbol which corresponds to
the selection, R , N , E or M and the
number of the gear engaged 1 to 5 ,
are displayed on the instrument panel
screen.
SENSODRIVE GEARBOX
The fi ve-speed " SensoDrive "
gearbox offers a choice between the
comfort of automatic operation or the
pleasure of manual gear changing .
Driving mode
Select the driving mode by moving
the gear lever.

R everse "R". This gear will be en-
gaged when stationary or at a speed
below approximately 4 mph (6 km/h).
The engagement of reverse gear is
accompanied by an audible signal.

N eutral "N".
Position the lever to the right in N , to

start the engine .

E asy "E": automatic gear changing.

M anual ( +/- ) "M": manual gear changing.
Starting the engine
With the parking brake applied, press
the brake pedal then select position N
to start the engine.
With your foot on the brake, select
position R , E or M .
Release the parking brake, take your
foot off the brake pedal, then accelerate.

Notes: with the engine run-
ning, in these three posi-
tions, an audible signal is
heard when the driver's door
is opened.
You can change from position E to
position M and vice versa at any
time.

Page 71 of 99

7
63
DRIVING
EASY mode (automatic mode)
Select position E using the gear lever.
The gear engaged is displayed on
the instrument panel screen.
The gearbox continuously selects
the most suitable gear.
If you press the accelerator pedal
beyond the point of resistance, the
SensoDrive gearbox changes down
to permit sharper acceleration.
Manual mode
Place the gear lever in position M ,
then change up or down through the
gears by pressing:
- rearwards, "+" to change up,
- forwards, "-" to change down.
The gear engaged is displayed on
the instrument panel screen.
If the engine speed is too low, the
gearbox automatically changes down
to prevent stalling.
In the event of overheating of the
clutch, position N is selected auto-
matically and the symbol N fl ashes
accompanied by an audible signal. Operating fault
Stopping the engine
Before switching off the engine, you
can change to position N to be in
neutral.
In all cases, it is essential that you
apply the parking brake to immobilise
the vehicle. With the ignition on, the
lighting of this warning
lamp indicates a gearbox
malfunction.
On a slope, use the brake to
immobilise the vehicle and
place the gear lever in posi-
tion N , E or R .
Do not keep the vehicle immobilised
using the accelerator. Always press the brake pedal
while starting the engine.
Never select neutral
N while
the vehicle is moving.
In all cases, it is essential to
apply the parking brake to
immobilise the vehicle.
Consult a CITROËN dealer.

Page 73 of 99

8
66
CHECKS
1.0 LITRE PETROL ENGINE

1. Coolant reservoir

2. Windscreen wash reservoir

3. Brake fl uid reservoir

4. Fuse box

5. Battery

6. Air fi lter

7. Engine oil dipstick

8. Engine oil fi ller cap
1.4 LITRE TURBO DIESEL HDI ENGINE

1. Coolant reservoir

2. Windscreen wash reservoir

3. Priming pump

4. Air fi lter

5. Brake fl uid reservoir

6. Fuse box

7. Battery

8. Engine oil dipstick

9. Engine oil fi ller cap

Page:   < prev 1-10 11-20 21-30 31-40 next >