display Citroen C4 2009 1.G Owner's Manual

23
I
I N S T R U M E N T S a n d C O N T R O L S
INSTRUMENT PANEL WITH TRANSLUCENT SCREEN
The instrument panel groups all the driving and comfort information at the centre of the dashboard.
Central display

1. Rev counter

2. Cruise control or speed limiter
setting

3. Speedometer

4. Maintenance indicator when the
ignition is switched on, then total
mileage recorder
5. Trip mileage recorder

6. Fuel gauge

7. Engine oil level check

8. Coolant temperature Control buttons

A. Trip mileage recorder reset

B. Lighting rheostat

C. Display of alerts and Status of
functions

25
I
I N S T R U M E N T S a n d C O N T R O L S
"Foot on brake" The fl ashing of this warning
lamp on the display informs
you that you need to press
the brake pedal in order to
be able to start the engine on a ve-
hicle with the (6-speed) Electronic
Gearbox System, or to move out of
position P in the case of an automatic
gearbox.
It may also fl ash to prompt you to
brake when engaging reverse gear.
In the case of the Electronic Gearbox
System, this warning lamp fl ashes to
indicate overheating of the clutch if
you use the accelerator excessively
to hold the vehicle on an uphill slope.
Use the brake pedal instead.
Electric child lock
If lit, the child lock is activa ted.
This warning lamp is displayed
a few seconds after the func-
tion is activated. Deactivation warning lamps
If one of the following warning lamps
comes on, this confi rms that the
corresponding system has been
switched off intentionally.
Passenger's air bag system
deactivation
Dynamic stability control
(ESP/ASR) deactivation
The ESP/ASR system is put
into service automatically
when the vehicle is started.
A specifi c button, located on the
dashboard, permits deactivation of
the system. This is confi rmed by
continuous lighting of this warning
lamp and of the indicator lamp on
the button.
From approximately 30 mph (50 km/h),
the system is reactivated automatically. Warning lamps
Diesel engine pre-heating
Wait until this has gone out
before operating the starter.
The passenger's air bag system is put into service automatically
when the vehicle is started.
A specifi c control, located in the glove
box, permits deactivation of the system.
This is confi rmed by continuous lighting
of this warning lamp on the instrument
panel or a message on the NaviDrive
multifunction screen.
When the engine is running or the
vehicle is moving, the lighting of
one of the following warning lamps
indicates the occurrence of a fault
requiring action on the part of the
driver.
Any fault resulting in the displaying of
a warning lamp must be investigated
further by reading the associated mes-
sage on the multifunction screen.
Should you encounter any problems,
do not hesitate to contact a CITROËN
dealer.

25
I
I N S T R U M E N T S a n d C O N T R O L S
"Foot on brake" The fl ashing of this warning
lamp on the display informs
you that you need to press
the brake pedal in order to
be able to start the engine on a ve-
hicle with the (6-speed) Electronic
Gearbox System, or to move out of
position P in the case of an automatic
gearbox.
It may also fl ash to prompt you to
brake when engaging reverse gear.
In the case of the Electronic Gearbox
System, this warning lamp fl ashes to
indicate overheating of the clutch if
you use the accelerator excessively
to hold the vehicle on an uphill slope.
Use the brake pedal instead.
Electric child lock
If lit, the child lock is activa ted.
This warning lamp is displayed
a few seconds after the func-
tion is activated. Deactivation warning lamps
If one of the following warning lamps
comes on, this confi rms that the
corresponding system has been
switched off intentionally.
Passenger's air bag system
deactivation
Dynamic stability control
(ESP/ASR) deactivation
The ESP/ASR system is put
into service automatically
when the vehicle is started.
A specifi c button, located on the
dashboard, permits deactivation of
the system. This is confi rmed by
continuous lighting of this warning
lamp and of the indicator lamp on
the button.
From approximately 30 mph (50 km/h),
the system is reactivated automatically. Warning lamps
Diesel engine pre-heating
Wait until this has gone out
before operating the starter.
The passenger's air bag system is put into service automatically
when the vehicle is started.
A specifi c control, located in the glove
box, permits deactivation of the system.
This is confi rmed by continuous lighting
of this warning lamp on the instrument
panel or a message on the NaviDrive
multifunction screen.
When the engine is running or the
vehicle is moving, the lighting of
one of the following warning lamps
indicates the occurrence of a fault
requiring action on the part of the
driver.
Any fault resulting in the displaying of
a warning lamp must be investigated
further by reading the associated mes-
sage on the multifunction screen.
Should you encounter any problems,
do not hesitate to contact a CITROËN
dealer.

25
I
I N S T R U M E N T S a n d C O N T R O L S
"Foot on brake" The fl ashing of this warning
lamp on the display informs
you that you need to press
the brake pedal in order to
be able to start the engine on a ve-
hicle with the (6-speed) Electronic
Gearbox System, or to move out of
position P in the case of an automatic
gearbox.
It may also fl ash to prompt you to
brake when engaging reverse gear.
In the case of the Electronic Gearbox
System, this warning lamp fl ashes to
indicate overheating of the clutch if
you use the accelerator excessively
to hold the vehicle on an uphill slope.
Use the brake pedal instead.
Electric child lock
If lit, the child lock is activa ted.
This warning lamp is displayed
a few seconds after the func-
tion is activated. Deactivation warning lamps
If one of the following warning lamps
comes on, this confi rms that the
corresponding system has been
switched off intentionally.
Passenger's air bag system
deactivation
Dynamic stability control
(ESP/ASR) deactivation
The ESP/ASR system is put
into service automatically
when the vehicle is started.
A specifi c button, located on the
dashboard, permits deactivation of
the system. This is confi rmed by
continuous lighting of this warning
lamp and of the indicator lamp on
the button.
From approximately 30 mph (50 km/h),
the system is reactivated automatically. Warning lamps
Diesel engine pre-heating
Wait until this has gone out
before operating the starter.
The passenger's air bag system is put into service automatically
when the vehicle is started.
A specifi c control, located in the glove
box, permits deactivation of the system.
This is confi rmed by continuous lighting
of this warning lamp on the instrument
panel or a message on the NaviDrive
multifunction screen.
When the engine is running or the
vehicle is moving, the lighting of
one of the following warning lamps
indicates the occurrence of a fault
requiring action on the part of the
driver.
Any fault resulting in the displaying of
a warning lamp must be investigated
further by reading the associated mes-
sage on the multifunction screen.
Should you encounter any problems,
do not hesitate to contact a CITROËN
dealer.

28
I
I N S T R U M E N T S a n d C O N T R O L S
5 seconds after the ignition is switched
on, the spanner is switched off ; the
distance recorder resumes its normal
operation. The display then indicates
the total and trip distances.
Less than 620 miles (1 000 km)
remain before the next service is due

Examples
: 400 miles (900 km) re-
main before the next service is due.
For 5 seconds after the ignition is
switched on, the display indicates: Service overdue
For 5 seconds after the ignition is
switched on,
the spanner fl ashes
to indicate that the service must be
carried out as soon as possible.

Example: the service is overdue by
300 miles/km.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is
switched on, the distance recorder
resumes its normal operation. The
spanner remains on to indicate that
a service must be carried out soon. 5 seconds after the ignition is
switched on, the distance recorder
resumes its normal operation.

The spanner remains lit .
More than 620 miles (1 000 km)
remain before the next service is due
For 5 seconds after the ignition is
switched on, the spanner symbol-
ising the service operations comes
on. The distance recorder display
line indicates the distance remaining
before the next service is due.

Example: 4 800 miles/km remain
before the next service is due.
For 5 seconds after the ignition is
switched on, the display indicates:
The distance remaining may be
weighted by the time factor, depend-
ing on the driver’s driving habits.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.

29
I
I N S T R U M E N T S a n d C O N T R O L S
Maintenance indicator zero reset Engine oil level indicator
After each service, the maintenance
indicator must be reset to zero.
The procedure for resetting to zero
is as follows:

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,

 switch on the ignition; the dis-
tance recorder display begins a
countdown,

 when the display indicates "=0" ,
release the button; the spanner
disappears. System which informs the driver
whether the engine oil level is correct
or not.
This information is displayed for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Oil level low
This is indicated by the fl ashing of

"OIL" , accompanied by an audible
signal and a message on the multi-
function screen.
If the low oil level is confi rmed by a
check using the dipstick, it is essential
that the level is topped up to prevent
damage to the engine. Oil level gauge fault
This is indicated by the fl ashing of

"OIL --" . Contact a CITROËN dealer.
Dipstick
Refer to the "Checks" section to
locate the dipstick and the oil fi ller
cap on your engine. There are 2 marks on
the dipstick:
- A = max; never ex-
ceed this level,
- B = min; top up the
level via the oil fi ller
cap, using the type
of oil suited to your
engine.
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into ac-
count.

30
I
I N S T R U M E N T S a n d C O N T R O L S
Total distance recorder
System which measures the total
distance travelled by the vehicle
during its life.
The total and trip distances are dis-
played for thirty seconds when the
ignition is switched off, when the
driver's door is opened and when
the vehicle is locked or unlocked.
Trip distance recorder
System which measures a distance
travelled during a day or other pe-
riod since it was reset to zero by the
driver.

 With the ignition on, press the
button until zeros appear. Dashboard lighting rheostat
Activation

 Turn control A or press control B
to adjust the brightness of the
dashboard lighting,

 With control B , press until the
brightness is at maximum, release,
press until you reach minimum.
Deactivation
When the lights are off, or in day mode
in the case of vehicles fi tted with day-
time running lights, the button has no
effect.
System permitting manual adjustment
of the brightness of the dashboard to
suit the level of ambient light.
The rheostat is active if the sidelamps
are on and applies to:
- the instrument panel,
- the display screens.

31
II
M U L T I F U N C T I O N S C R E E N S
MULTIFUNCTION SCREEN A
Presentation

1. Time

2. Date and display zone

3. Ambient temperature
When the ambient temperature is
between +3 °C and -3 °C, the tem-
perature display fl ashes (ice risk).
The ambient temperature displayed
may be greater than the actual tem-
perature, if the vehicle is parked in
bright sunlight.
The display of certain types of in-
formation is sometimes by scrolling
and sometimes by alternating be-
tween them.
A. Access to the "Main Menu"

B. Scrolling in the screen menus

C. Selection and confi rmation in the
menus of the function chosen or
the value modifi ed

D. Cancellation of the operation or
return to the previous display

E. Selection of the type of information
to be displayed in zone 2 (date,
radio-CD and trip recorder)

B or F. Within the menus, choice
of activation/deactivation of
functions and selection of
adjustments
Controls Main Menu
By pressing button A , then using
button B , you have access to the
following functions:

33
II
M U L T I F U N C T I O N S C R E E N S
MULTIFUNCTION SCREEN C Main Menu
Presentation
Radio-CD
(see "Audio and
Telematics")
Trip computer
This permits:
Bluetooth
®
hands-free
system
(see "Audio and
Telematics")
Controls

1. Time

2. Ambient temperature

3. Date and display zone
When the ambient temperature is
between +3 °C and -3 °C, the tem-
perature display fl ashes (ice risk).
The ambient temperature displayed
may be greater than the actual tem-
perature, if the vehicle is parked in
bright sunlight.
It is recommended that the driver
should not operate the controls
while the vehicle is in motion.
A. Access to the "Main Menu"

B. Scrolling in the screen menus

C. Selection and confi rmation in the
menus of the function chosen or
the value modifi ed

D. Cancellation of the operation or
return to the previous display

E. Selection of the type of informa-
tion to be displayed permanently
(date, radio-CD, trip computer)
on the right of the screen (See
"Trip computer") Press button
A to view the "Main
Menu" of the multifunction screen.
This menu gives you access to the
following functions:
- entering the distance to your destination,
- access to the log of alerts (recall of alerts signalled previously),
- access to the status of functions, such as the activation/deactivation
of the automatic headlamps, of the
automatic windscreen wipers, of
the ESP...

36
II
M U L T I F U N C T I O N S C R E E N S
NAVIDRIVE MULTIFUNCTION COLOUR SCREEN
Presentation

1. Ambient temperature

2. Directory

3. Date

4. Telephone

5. Time
When the ambient temperature is be-
tween +3 °C and -3 °C, the tempera-
ture display fl ashes (risk of ice).
The ambient temperature displayed
may be greater than the actual tem-
perature, if the vehicle is parked in
bright sunlight.
It is recommended that the driver
should not operate the controls
while the vehicle is in motion. Controls Main Menu

Traffi c Information

Navigation/Guidance

Map

Audio Functions

Telematics

Confi guration,
for adjusting various parameters
(date, time, units)

Video

Vehicle Diagnostics

A. Access to the "Main Menu"

B. Scrolling in the screen menus

C. Selection and confi rmation in the
menus of the function chosen or
the value modifi ed

D. Cancellation of the operation or
return to the previous display

E. Selection of the type of informa-
tion to be displayed permanently
(date, radio-CD, trip computer)
on the right of the screen Press on the button
A to view the
"Main Menu" of the multifunction
screen.
This menu gives you access to the
following functions (see "NaviDrive
Instructions"):