gearbox Citroen C4 2016 2.G Owner's Guide

189
C4-2_en_Chap06_conduite_ed02-2015
Deactivation
Going into engine START mode
At any time, press the "ECO OFF" switch to
d eactivate   the   system.
This
  is   confirmed   by   the   switch   warning   lamp  
c

oming   on   accompanied   by   the   display   of   a  
m

essage.
Special cases: START invoked
automatically
The "ECO"  warning   lamp   goes   off  a
nd   the   engine   starts   automatically:
-

w

ith a manual gearbox , when you fully
depress the clutch pedal,
-

w

ith an automatic gearbox:
●
 
g

ear   selector   in   position   D or M, when
you
  release   the   brake   pedal,
●
 
o

r
 
gear   selector   in   position   N   and   brake  
p

edal   released,   when   you   place   the   gear  
s

elector in position D or M ,
●
 
o

r
 
when   you   engage   reverse   gear.For
  safety   reasons   or   to   ensure   smooth  o
peration,   START   mode   is   invoked  
a

utomatically
 w
hen:
-
 
y
ou   open   the   driver's   door,
-
 
y
ou   unfasten   the   driver's   seat   belt,
-
 
t
he   speed   of   the   vehicle   exceeds   15   mph  
(

25   km/h)   with   a   manual   gearbox   (3   km/h  
(

2   mph)   with   PureTech   130   petrol   and  
B

lueHDi   Diesel   115   and   120   versions)   or  
2 m

ph   (3   km/h)   with   an   automatic   gearbox,
-
 
t
he   electric   parking   brake   is   being   applied,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
In this case the "ECO"
 

warning   lamp  
f

lashes   for   few   seconds,   then   goes  
o

f f.
This operation is perfectly normal.
With
  a   manual   gearbox   in   STOP   mode,  
i

f
 
a
  gear   is   engaged   without   fully  
d

epressing   the   clutch   pedal,   a   warning  
l

amp   comes   on   or   an   alert   message  
i

s
 
displayed   asking   you   to   depress   the  
c

lutch   pedal   to   restart   the   engine. If
  the   system   has   been   deactivated  
i

n   STOP   mode,   the   engine   restarts  
i

mmediately.
6
Driving

191
C4-2_en_Chap06_conduite_ed02-2015
Hill start assist
On an ascending slope, with the vehicle
stationar y, the vehicle is held for a brief
moment when you release the brake pedal:
- 
i
f   you   are   in   first   gear   or   neutral   with   a  
m

anual
 g
earbox,
-

i
f you are in position D or M with an
automatic
  gearbox.
Operation
On a descending slope, with the vehicle
stationary and reverse gear engaged, the
vehicle is held for a brief moment when you
release the brake pedal.
Operating fault
If a fault occurs with the system, these warning lamps   come   on.   Contact   a   CITROËN   dealer  
o

r   a   qualified   workshop   to   have   the   system  
c

hecked.
System
 
which
 
keeps
 
your
 
vehicle
 
immobilised
 
t

emporarily
 
(approximately
 
2
 
seconds)
 
when
 
s

tarting
 
on
 
a
 
gradient,
 
the
 
time
 
it
 
takes
 
to
 
m

ove
 
your
 
foot
 
from
 
the
 
brake
 
pedal
 
to
 
the
 
a

ccelerator
 ped

al.
This
 
function
 
is
 
only
 
active
 
when:
-
 
t

he
 
vehicle
 
is
 
completely
 
stationary,
 
with
 
y

our
 
foot
 
on
 
the
 
brake
 
pedal,
-
 
w

hen
 
certain
 
conditions
 
of
 
gradient
 
are
 
m

et,
-
 
w

ith
 
the
 
driver’s
 
door
 
closed.
The hill start assist function cannot be
deactivated.
Do
 
not
 
leave
 
the
 
vehicle
 
while
 
it
 
is
 
being
 
h

eld
 
in
 
the
 
hill
 
start
 
assist
 
phase.
If you need to leave the vehicle while
the
 
engine
 
is
 
running,
 
apply
 
the
 
parking
 b
rake
 
manually
 
then
 
ensure
 
that
 
the
 p
arking
 
brake
 
warning
 
lamp
 
is
 
on
 
(not
 
f

lashing)
 
in
 
the
 
instrument
 
panel.
6
Driving

201
C4-2_en_Chap06_conduite_ed02-2015
Cruise control
1. Cruise  control   mode   selection   wheel.
2. B utton   for   setting   the   current   speed   of   the  
v

ehicle   as   the   cruise   setting   or   lowering   the  
c

ruise
 se
tting.
3.
 B

utton   for   setting   the   current   speed   of   the  
v

ehicle   as   the   cruise   setting   or   raising   the  
c

ruise
 se
tting.
4.
 C

ruise   control   pause   /   resume   button.
5.
 D

isplay   memorised   speed   settings   button.
Steering mounted controls
6. Cruise  control   pause   /   resume   indication.
7. C ruise   control   mode   selected   indication.
8.
 C

ruise   speed   setting.
9.
 S

electing   a   memorised   cruise   speed.
Displays in the instrument panel
The operation of the cruise control can be
interrupted (pause):
-
 
b
y   pressing   control   4   or   by   pressing   the  
b

rake   or   clutch   pedal,
-
 
a
utomatically,   if   operation   of   the   dynamic  
s

tability   control   system   is   triggered.
Switching
  off   the   ignition   cancels   any  
p

rogrammed   speed   setting.
The cruise control is switched on

manually.
It   requires   a   minimum   vehicle   speed   of  
2

5   mph   (40   km/h)   as   well   as:
-  
w
ith   a   manual   gearbox,   the  
e

ngagement   of   fourth   gear   or  
h

igher,
-  
w
ith   an   automatic   gearbox,   the   gear  
s

elector at position D or second
gear   or   higher   in   manual   mode.
System   which   automatically   maintains   the   cruising   speed   of   the   vehicle   at   a   setting   programmed   by  
t

he   driver,   without   any   action   on   the   accelerator   pedal.
The   cruise   control   system   is   a   driving   aid
 t

hat   cannot,   in   any   circumstances,   replace
 t

he   need   to   observe   speed   limits,   nor   the
 n

eed   for   vigilance   on   the   part   of   the   driver.As
  a   safety   measure,   you   are   advised  
t

o   keep   your   feet   near   the   pedals   at   all  
ti

mes.
6
Driving

231
C4-2_en_Chap07_infos-pratiques_ed02-2015
Automatic gearbox
The gearbox does not require any maintenance   (no   oil   change).
Refer
  to   the   manufacturer's  
s

ervice schedule for details of
the
  level   checking   interval   for   this  
c

omponent.
Electric parking brake
This system does not require any routine   servicing.   However,   in  
t

he   event   of   a   problem,   have   the  
s

ystem   checked   by   a   CITROËN  
d

ealer   or   a   qualified   workshop.
Manual parking brake
If a loss of effectiveness of this
system i s  n oticed,  t he  p arking  b rake  
m

ust   be   checked,   even   between  
t

wo   services.
Brake pads
Brake wear depends on the style of   driving,   particularly   in   the   case  
o

f vehicles used in town, over short
distances.
  It   may   be   necessary   to  
Brake disc wear
For information on checking brake disc wear, contact a CITROËN
dealer
  or   a   qualified   workshop.
For
  more   information   on   the   electric   parking  
b

rake,   refer   to   the   corresponding   section.
Manual gearbox
The gearbox does not require any maintenance   (no   oil   change).
Refer
  to   the   manufacturer's   service  
s

chedule   for   the   checking   interval  
f

or   this   component.
Only
  use   products   recommended   by  
C

ITROËN   or   products   of   equivalent  
q

uality
 an
d
 sp
ecification.
In
  order   to   optimise   the   operation   of  
u

nits   as   important   as   those   in   the  
b

raking   system,   CITROËN   selects   and  
o

ffers   very   specific   products.
After
  washing   the   vehicle,   dampness,  
o

r   in   wintry   conditions,   ice   can   form  
o

n   the   brake   discs   and   pads:   braking  
e

fficiency   may   be   reduced.   Make   light  
b

rake   applications   to   dry   and   defrost  
t

he   brakes.
have
 
the
 
condition   of   the   brakes   checked,   even  
b

etween
 v

ehicle
 s
ervices.
Unless
 
there   is   a   leak   in   the   circuit,   a   drop   in  
t

he
 
brake
 
fluid   level   indicates   that   the   brake  
p

ads
 
are
 
worn. Checking
  this   system   must   be   done   by   a  
C

ITROËN   dealer   or   a   qualified   workshop.
7
Practical information

247
C4-2_en_Chap08_en-cas-de-panne_ed02-2015
Removing a wheel
* position P for an automatic gearbox.
List of operations
Parking the vehicle
Immobilise the vehicle where it does not b
lock   traffic:   the   ground   must   be   level,  
s

table   and   non-slippery   ground.
Apply
  the   parking   brake   unless   it   has  
b

een   programmed   to   automatic   mode,  
s

witch   off   the   ignition   and   engage   first  
g

ear*   to   lock   the   wheels.
Check
  that   the   braking   warning   lamps  
i

n   the   instrument   panel   are   on   (not  
f

lashing).
The
  occupants   must   get   out   of   the  
v

ehicle   and   wait   where   they   are   safe.
If
  necessary,   place   a   chock   under   the  
w

heel   diagonally   opposite   the   wheel   to  
be c

hanged.
Never
  go   underneath   a   vehicle   raised  
u

sing   a   jack;   use   an   axle   stand.F
 
R
emove   the   bolt   cover   from   each   of  
t

he   bolts   using   the   tool   3   (according   to  
e

quipment).
F
 
F
it   the   security   socket   4 on the
wheelbrace


1   to   slacken   the   security   bolt.
F
 
S
lacken   the   other   bolts   using   the  
w

heelbrace 1  
o
n l y.
8
In the event of a breakdown

269
C4-2_en_Chap08_en-cas-de-panne_ed02-2015
Towing the vehicle
The towing eye is installed in the boot under the   floor.
To
  gain   access   to   it:
F

o
pen the boot,
F

r
aise the floor,
F
 
s
ecure   it   by   hooking   its   cord   on   the   hook  
o

n the rear parcel shelf support,
F
 
r
emove   the   towing   eye   from   the   holder.
Access to the tools General recommendations
In the following cases, you must always call o
n   a   professional   recovery   service:
-
 
v
ehicle   broken   down   on   a   motor way   or  
f

ast road,
-
f

our-wheel drive vehicle,
-

w
hen it is not possible to put the
gearbox
  into   neutral,   unlock   the  
 
s

teering,   or   release   the   parking   brake,
-
 
t
owing   with   only   two   wheels   on   the  
g

round,
-
 
w
here   there   is   no   approved   towing   arm  
a

vailable...
Procedure
 
for
 
having
 
your
 
vehicle
 
towed
 
or
 
for
 
towing
 
another
 
vehicle
 
using
 
a
 
removable
 
towing
 
eye.
Observe
 
the
 
legislation
 
in
 
force
 
in
 
your
 c
o unt r y.
Ensure
 
that
 
the
 
weight
 
of
 
the
 
towing
 
vehicle
 
i

s
 
higher
 
than
 
that
 
of
 
the
 
towed
 
vehicle.
The
 
driver
 
must
 
remain
 
at
 
the
 
wheel
 
of
 
the
 
t

owed
 
vehicle
 
and
 
must
 
have
 
a
 
valid
 
driving
 
l

icence.
When
 
towing
 
a
 
vehicle
 
with
 
all
 
four
 
wheels
 
o

n
 
the
 
ground,
 
always
 
use
 
an
 
approved
 
t

owing
 
arm;
 
rope
 
and
 
straps
 
are
 
prohibited.
The
 
towing
 
vehicle
 
must
 
move
 
off
 
gently.
When
 
towing
 
a
 
vehicle
 
with
 
the
 
engine
 
off,
 
t

here
 
is
 
no
 
longer
 
any
 
power
 
assistance
 
for
 
b

raking
 
or
 
steering.
8
In the event of a breakdown

271
C4-2_en_Chap09_caracteristiques_ed02-2015
Petrol engines and gearboxes
Petrol enginePureTech 110 V Ti 120 PureTech 130 S&S
Gearbox Manual
(5 - speed) Manual

(5 - speed) Manual
(6- speed) E AT 6
automatic (6- speed)
Model c ode:
NC... HNZ6
HNZ6/1
HNZ6/2 5FS0
HNYM/S
HNYM/1S HNY T/S
HNY T/1S
HNY T/2S
Cubic
  capacity   (cc) 1 19 91
  5981 19 9
Bore
  x   stroke   (mm) 75
  x   90.577
  x   85.875
  x   90.5
Max
  power*:   EU   standard   (kW) 8188 96
Max
  power   engine   speed   (rpm) 5 5006
  0005 500
Max
  torque:   EU   standard   (Nm) 205160 230
Max
  torque   engine   speed   (rpm) 1 5004 250 1
  750
Fuel UnleadedUnleaded Unleaded
Catalytic converter Ye sYe s Ye s
Oil capacity in litres
(with filter replacement) 3.5
4.25 3.5
.../S:
 

model   fitted   with   Stop   &   Start.
.../1:  model
  fitted   with   low   rolling   resistance   tyres.
.../2:  model
  fitted   with   very   low   rolling   resistance   tyres.
*
  The   maximum   power   corresponds   to   the   value   type-approved   on   a   test   bed,   under   conditions   defined   in   European   legislation   (Directive   1999/99/EC).
9
Technical data

272
C4-2_en_Chap09_caracteristiques_ed02-2015
Petrol weights and towed loads (in kg)
The GTW and towed load values indicated are valid up to a maximum altitude of 1 000 metres; the towed load mentioned must be reduced by 10 % for each   additional   1   000   metres   of   altitude.
When
  towing,   the   maximum   authorised   speed   is   reduced   (comply   with   the   legislation   in   force   in   your   country).
High
  ambient   temperatures   may   result   in   a   reduction   in   the   per formance   of   the   vehicle   to   protect   the   engine;   if   the   ambient   temperature   is   above   37   °C,  
l

imit   the   towed   load.
Petrol engine
PureTech 110 V Ti 120 PureTech 130 S&S
Gearbox Manual

(5 - speed) Manual

(5 - speed) Manual
(6- speed) EAT6 automatic
(6- speed)
Model code:
NC... HNZ6
HNZ6/1 -/2 5FS0HNYM/S
HNYM/1S HNY T/S
HNY T/1S - /2S
-  
U
nladen   weight
1 2001 2051 205 1 240
-  
K
erb   weight*
1   275
1   280
1   280
1   315
-  
G
ross   vehicle   weight   (GV W)
1   770
1   765
1   790
1   810
-  
G
ross   train   weight   (GTW)  
 
o
n   a   12   %   gradient
2   970
3   065
3   090
3   110
-  
B
raked   trailer   (within   the   GTW   limit)  
 
o
n   a   12   %   gradient
1 200
1   300
1   300
1   300
-  
B
raked   trailer**   (with   load   transfer   within   the  
G

TW   limit)
1 450
1 550 1 5501 550
-  
U
nbraked   trailer
635640 640 655
-  
R
ecommended   nose   weight
75757575
*   The   kerb   weight   is   equal   to   the   unladen   weight   +   driver   (75   kg).
**   
T
he   weight   of   the   braked   trailer   can   be   increased,   within   the   GTW   limit,   if   the   GV W   of   the   towing   vehicle   is   reduced   by   an   equal   amount.   Warning:  
t

owing   using   a   lightly   loaded   towing   vehicle   may   have   an   adverse   effect   on   its   road   holding.
Technical data

273
C4-2_en_Chap09_caracteristiques_ed02-2015
Diesel engines and gearboxes
* The maximum power corresponds to the value type-approved on a test bed, under conditions defined in European legislation (Directive 1999/99/EC).
D iesel engine
HDi 90HDi 90 FAP BlueHDi 100 e-HDi 115
Gearbox Manual
(5 - speed) Manual
(5 - speed) Manual
(5 - speed) Manual
(6- speed)
Model code:
NC... 9HJC

9HJC/1 9HP0BHY6
BHY6/1
BHY6/2S 9HD8/S

9HD8/1S
9HD8/2S
Cubic   capacity   (cc)
1   560
1   560
1   560
1   560
Bore   x   stroke   (mm)
75   x   88.3
75   x   88.3
75   x   88.3
75   x   88.3
Max   power*:   EU   standard   (kW)
6868 7384
Max   power   engine   speed   (rpm)
4 0004 000 3   750
3   600
Max   torque:   EU   standard   (Nm)
230230254 270
Max   torque   engine   speed   (rpm)
1   750
1   750
1   750
1   750
Fuel DieselDieselDieselDiesel
Catalytic converter Ye sYe sYe sYe s
Particle   filter   (FAP)
NoYe s Ye sYe s
Oil capacity in litres
(with filter replacement) 3.75
3.753.753.75
.../S:
 
model   fitted   with   Stop   &   Start.
.../1:
 

model   fitted   with   low   rolling   resistance   tyres   (for   example:   MICHELIN   Energy   Saver).
.../2:
 

model   fitted   with   very   low   rolling   resistance   tyres.
9
Technical data

274
C4-2_en_Chap09_caracteristiques_ed02-2015
.../S: model   fitted   with   Stop   &   Start.
.../1:  model   fitted   with   low   rolling   resistance   tyres   (for   example:   MICHELIN   Energy   Saver).
.../2:
 

model   fitted   with   very   low   rolling   resistance   tyres.
Diesel engine
BlueHDi 115 S&SBlueHDi 120 S&SBlueHDi 150
S&S
Gearbox Manual
(6- speed) E AT 6
automatic (6- speed) Manual
(6- speed) E AT 6
automatic (6- speed) Manual
(6- speed)
Model code:
NC... BHXM/S
BHXM/1S
BHXM/2S BHX T/S
BHX T/1S
BHX T/2S BHZM/S
BHZM/1S
BHZM/2S BHZT/S
BHZ T/1S
BHZT/2S AHRM/S
AHRM/1S
AHRM/2S
Cubic   capacity   (cc)
1   560
1   560
1   997
Bore   x   stroke   (mm)
75   x   88.3
75   x   88.3
85   x   88
Max   power*:   EU   standard   (kW)
858811 0
Max   power   engine   speed   (rpm)
3   500
3   500
4 000
Max   torque:   EU   standard   (Nm)
300300370
Max   torque   engine   speed   (rpm)
1   750
1   750
2 000
Fuel DieselDieselDiesel
Catalytic converter Ye sYe sYe s
Particle   filter   (FAP)
Ye sYe sYe s
Oil capacity in litres
(with filter replacement) 3.75
3.756 .1
*   The   maximum   power   corresponds   to   the   value   type-approved   on   a   test   bed,   under   conditions   defined   in   European   legislation   (Directive   1999/99/EC).
Technical data