display Citroen C4 PICASSO 2008.5 1.G User Guide

28
I
I N S T R U M E N T S a n d C O N T R O L S
"Foot on brake" The fl ashing of this warning
lamp on the display informs
you that you need to press
the brake pedal in order to be
able to start the engine on a vehicle
with the (6-speed) Electronic Gearbox
System, or to quit position P in the
case of an automatic gearbox.
This warning lamp comes on if
you attempt to release the electric
parking brake without pressing the
brake pedal.
In the case of the Electronic Gearbox
System, this warning lamp fl ashes
to indicate overheating of the clutch
if you excessively use the accelera-
tor to hold the vehicle on an uphill
slope. Use the brake pedal or the
electric parking brake.
Parking space available
This warning lamp comes
on when the parking space
function is selected.
It fl ashes while the space is
being measured. Electric child lock
If lit, the child lock is activat-
ed. This warning light is dis-
played a few seconds after
the function is activated.
Deactivation warning lights
If one of the following warning lights
comes on, this confi rms that the
corresponding system has been
switched off intentionally.
Passenger's air bag system
deactivation
Dynamic stability control
(ESP/ASR) deactivation The ESP/ASR system is put
into service automatically
when the vehicle is started. Warning lights
Diesel engine pre-heating
Wait until this is switched off before
operating the starter.
The passenger's air bag
system is put into service
automatically when the ve-
hicle is started.
A specifi c control, located in the glove
box, permits deactivation of the sys-
tem. This is confi rmed by continuous
lighting of this warning light on the
instrument panel or a message on
the NaviDrive multifunction screen. A specifi c button, located in the cen-
tre of the fascia, permits deactiva-
tion of the system. This is confi rmed
by continuous lighting of this warn-
ing light and of the indicator light on
the button.
From approximately 30 mph (50km/h),
the system is reactivated automatically.
When the engine is running or the
vehicle is moving, the lighting of one of
the following warning lights indicates
the occurrence of a fault requiring inter-
vention on the part of the driver.
Any fault resulting in the display-
ing of a warning light must be the
subject of further diagnostics by
reading the associated message
on the multifunction display.
Should you encounter any prob-
lems, do not hesitate to contact a
CITROËN dealer.

29
I
I N S T R U M E N T S a n d C O N T R O L S
Lighting is associated
with the displaying of
another warning light:
Service If this comes on, it indi-
cates the occurrence of
a problem in one of the
systems which does
not have a specifi c
warning light.
In order to identify it, consult the mes-
sage on the multifunction display.
The warning light only comes on
temporarily in the case of the follow-
ing minor faults:
- incorrect closing of the doors, boot, rear screen and bonnet,
- fl at remote control battery,
- incorrect tyre pressure,
- the end of saturation of the particle emission fi lter (Diesel).
In the case of major faults, the
warning light remains on until the
operating fault is rectifi ed, contact a
CITROËN dealer as soon as possible. Braking
If this comes on, it indicates
the occurrence of a fault in
one of the braking systems:
- signifi cant drop in the level in the circuit,
- electronic brake force distribu- tion (EBFD) faulty (simultaneous
lighting of the ABS warning light),
stop the vehicle immediately and as
safely as possible.
Consult a CITROËN dealer.

Application/Release of the
automatic electronic parking
brake
If this warning lamp comes
on permanently, it is confi rm-
ing that the parking brake is
applied.
If it fl ashes, it is indicating an ap-
plication or release fault. Urgently
contact a CITROËN dealer (see sec-
tion "Driving - § Electronic parking
brake"). Automatic electronic parking
brake fault
This warning lamp comes
on if there is a malfunction
in the automatic electronic
parking brake.
Deactivation of the automatic
functions of the automatic
electronic parking brake
This comes on if the "auto-
matic application" and "au-
tomatic release" functions
when you switch off the
engine are deactivated or
faulty.
Dynamic stability control
(ESP/ASR) The ESP/ASR system is put
into service automatically
when the vehicle is started.
Unless the system has been deactivat-
ed, if this warning light and the indicator
light on the button come on continu-
ously, this indicates the occurrence of
a fault in the ESP/ASR system or in the
hill start assistance.
Engine autodiagnostics system
If this comes on, it indicates
the occurrence of a fault in
the engine management
system.
If it fl ashes, it indicates the occurrence
of a fault in the emission control sys-
tem.
Central alert
- punctured wheel,
- braking,
- coolant temperature,
stop the vehicle immediately and as
safely as possible.
Consult a CITROËN dealer.
Anti-lock braking system (ABS) If this comes on, it indicates
the occurrence of a fault in
the anti-lock braking system.
However, this does not prevent op-
eration of the vehicle's assisted
braking.

31
I
I N S T R U M E N T S a n d C O N T R O L S
Maintenance indicator
System which informs the driver
when the next service is due, in ac-
cordance with the manufacturer's
servicing schedule.
The point at which the service is due
is calculated from the last indicator
zero reset. It is determined by two
parameters:
- the distance travelled,
- the time elapsed since the last service. 5 seconds after the ignition is switched
on,
the spanner is switched off ; the
distance recorder resumes its normal
operation. The display then indicates
the total and trip distances.
Less than 620 miles (1 000 km)
remain before the next service is
due

Example: 560 miles (900 km) re-
main before the next service is due.
For 5 seconds after the ignition is
switched on, the display indicates: Service overdue
For 5 seconds after the ignition is
switched on,
the spanner fl ashes
to indicate that the service must be
carried out as soon as possible.

Example: the service is overdue by
300 miles/km.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is
switched on, the distance recorder
resumes its normal operation. The
spanner remains on to indicate that
a service must be carried out soon. 5 seconds after the ignition is
switched on, the distance recorder
resumes its normal operation.
The
spanner remains lit
.

More than 620 miles (1 000 km)
remain before the next service is
due
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the service operations comes
on. The distance recorder display
line indicates the distance remaining
before the next service is due.

Example: 4 800 miles/km remain
before the next service is due.
For 5 seconds after the ignition is
switched on, the display indicates:
The distance remaining may be
weighted by the time factor, depending
on the driver's driving habits.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.

32
I
I N S T R U M E N T S a n d C O N T R O L S
Maintenance indicator zero reset Engine oil level indicator
After each service, the maintenance
indicator must be reset to zero.
To do this, carry out the following
procedure:

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,

 switch on the ignition; the dis-
tance recorder display begins a
countdown,

 when the display indicates "=0" ,
release the button; the spanner
disappears. System which informs the driver of
the validity or invalidity of the engine
oil level.
This information is indicated for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Lack of oil
This is indicated by the fl ashing of

"OIL" , accompanied by an audible
signal and a message on the multi-
function display.
If the lack of oil is confi rmed by a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
This is indicated by the fl ashing of

"OIL --" . Consult a CITROËN dealer.
Dipstick
Refer to the "Checks" section to lo-
cate the dipstick and the oil fi ller cap
on your engine. There are 2 marks on
the dipstick:
- A = max; never ex-
ceed this level,
- B = min; top up the
level via the oil fi ller
cap, using the type
of oil suited to your
engine.
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into
account.

32
I
I N S T R U M E N T S a n d C O N T R O L S
Maintenance indicator zero reset Engine oil level indicator
After each service, the maintenance
indicator must be reset to zero.
To do this, carry out the following
procedure:

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,

 switch on the ignition; the dis-
tance recorder display begins a
countdown,

 when the display indicates "=0" ,
release the button; the spanner
disappears. System which informs the driver of
the validity or invalidity of the engine
oil level.
This information is indicated for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Lack of oil
This is indicated by the fl ashing of

"OIL" , accompanied by an audible
signal and a message on the multi-
function display.
If the lack of oil is confi rmed by a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
This is indicated by the fl ashing of

"OIL --" . Consult a CITROËN dealer.
Dipstick
Refer to the "Checks" section to lo-
cate the dipstick and the oil fi ller cap
on your engine. There are 2 marks on
the dipstick:
- A = max; never ex-
ceed this level,
- B = min; top up the
level via the oil fi ller
cap, using the type
of oil suited to your
engine.
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into
account.

34
II
M U L T I F U N C T I O N D I S P L A Y S
MULTIFUNCTION SCREEN A
Presentation

1. Time

2. Date and display zone

3. Outside temperature
When the outside temperature is be-
tween +3 °C and -3 °C, the tempera-
ture display fl ashes (ice risk).
The outside temperature displayed
may be greater than the actual tem-
perature, if the vehicle is parked in
bright sunlight.
The display of certain types of in-
formation is sometimes by scrolling
and sometimes by alternation.
A. Access to the "Main Menu"

B. Scrolling in the screen menus

C. Validation and selection in the
menus of the function chosen or
the value modifi ed

D. Cancellation of the operation or
return to the previous display

E.
Selection of the type of informa-
tion to be displayed in zone 2
(date, radio-CD and trip recorder)

B or F. Within the menus, choice
of activation/deactivation of
functions and selection of
adjustments By pressing on the button
A , then
using button B , you have access to
the following functions:

36
II
M U L T I F U N C T I O N D I S P L A Y S
MULTIFUNCTION SCREEN C Main Menu
Presentation
Radio-CD
(see "Audio")
Trip computer
This permits:
Bluetooth
®
hands-free
kit
(see "Audio")
Controls

1. Time

2. Outside temperature

3. Date and display zone
When the outside temperature is be-
tween +3 °C and -3 °C, the tempera-
ture display fl ashes (ice risk).
The outside temperature displayed
may be greater than the actual tem-
perature, if the vehicle is parked in
bright sunlight.
It is recommended that the driver
should not manipulate the controls
while the vehicle is in motion.

A. Access to the "Main Menu"

B. Scrolling in the screen menus

C. Validation and selection in the
menus of the function chosen or
the value modifi ed

D. Cancellation of the operation or
return to the previous display

E. Selection of the type of informa-
tion to be displayed permanently
(date, radio-CD, trip computer)
on the right of the screen Press on the button
A to view the
"Main Menu" of the multifunction
screen. This menu gives you access
to the following functions:
- entering the distance to your destination,
- access to the log of alerts (recall of alerts signalled previously),
- access to the status of functions, such as the activation/deactiva-
tion of the automatic headlamps,
of the automatic windscreen
wipers, of the ESP...

40
II
M U L T I F U N C T I O N D I S P L A Y S
NAVIDRIVE MULTIFUNCTION SCREEN
Presentation

1. Outside temperature

2. Directory

3. Date

4. Telephone

5. Time
When the outside temperature is be-
tween +3 °C and -3 °C, the tempera-
ture display fl ashes (ice risk).
The outside temperature displayed
may be greater than the actual tem-
perature, if the vehicle is parked in
bright sunlight.
It is recommended that the driver
should not manipulate the controls
while the vehicle is in motion.
Controls Main Menu

Traffi c Information

Navigation/Guidance

Map

Audio Functions

Telematics

Confi guration,
for adjusting various parameters
(date, time, units)

Video

Vehicle Diagnostics

A. Access to the "Main Menu"

B. Scrolling in the screen menus

C. Validation and selection in the
menus of the function chosen or
the value modifi ed

D. Cancellation of the operation or
return to the previous display

E. Selection of the type of informa-
tion to be displayed permanently
(date, radio-CD, trip computer)
on the right of the screen Press on the button
A to view the
"Main Menu" of the multifunction
screen.
This menu gives you access to the
following functions (see "NaviDrive
Instructions"):

41
II
M U L T I F U N C T I O N D I S P L A Y S
TRIP COMPUTER
System which provides current infor-
mation concerning the route travelled
(range, consumption...).
Monochrome display A Data displays


Press the control for more than
two seconds to reset the distance
travelled, the average consump-
tion and the average speed to
zero.
Zero reset
The trip computer data is the following:
- the range,
- the current consumption,
- the distance travelled,
- the average consumption,
- the average speed.

 The next press then returns you
to the normal display.

 Press the button, located at the
end of the wipers stalk , to dis-
play the various items of trip
computer data in succession.

42
II
M U L T I F U N C T I O N D I S P L A Y S
TRIP COMPUTER
System which provides current infor-
mation concerning the route travelled
(range, consumption, …).
Monochrome display C
NaviDrive colour display Data displays
Route zero reset

 Press the button, located at the
end of the wipers stalk , to dis-
play the various trip computer
tabs in succession:
- the current information tab with: