ignition Citroen C4 PICASSO 2016 2.G Owner's Guide

134
C4-Picasso-II_en_Chap04_conduite_ed01-2016
Special cases
Application of the parking brake is confirmed by illumination of
the
  brake   indicator   lamp   and  
t

he P indicator lamp in the control
lever, accompanied by the display of
the
 m

essage
 "
Parking
 b
rake
 a
pplied". The
  complete   release   of   the   parking  
b

rake   is   confirmed   by   the   brake  
i

ndicator lamp and the P indicator
lamp   in   the   control   lever   going   off,  
a

ccompanied by the display of the
message   "Parking   brake   released".
In some situations, you may need to operate
the
 
parking   brake   manually.
Immobilisation of the vehicle
with the engine running
To immobilise the vehicle with the engine r
unning,   briefly   pull   the   control   lever.
Parking the vehicle with the
brake released
In very cold conditions, it is
recommended  that   the   parking   brake  
n

ot   be   applied   (risk   of   freezing).
To
  immobilise   your   vehicle,   engage   a  
g

ear   or   fit   a   chock   to   one   of   the   wheels.
Immobilisation of the vehicle with the
parking brake released
F
 
S

witch   off   the   engine.
 I

llumination   of   the   warning   lamps   in   the  
i

nstrument panel and control lever confirm
application
  of   the   parking   brake,
F
 
S

witch   on   the   ignition   again,   without  
s

tarting   the   engine.
F
 
R

elease   the   parking   brake   manually   by  
p

ushing   the   control   lever   while   keeping  
y

our   foot   on   the   brake. F
 
S
witch   off   the   ignition.
Driving

140
C4-Picasso-II_en_Chap04_conduite_ed01-2016
Automatic gearbox
This gearbox offers two driving modes.
- a utomated mode for automatic
management
  of   the   gears   by   the   gearbox,  
w

ithout any action on the part of the driver,
-

m
anual
 
mode   for   sequential   gear   changing  
b

y   the   driver   using   the   steering   mounted  
p

addles.
P.
 Pa

rk.
-
 
I
mmobilisation   of   the   vehicle,   parking   brake  
a

pplied   or   released.
-
 
S
tarting   the   engine.
R.
 R

everse.
-
 
R
eversing,   vehicle   stationary   and   engine   at  
i

dle.
N.
 N

eutral.
-
 
I
mmobilisation   of   the   vehicle,   parking   brake  
a

pplied.
-
 
S
tarting   the   engine.
D.
 A

utomatic
 ope
ration.
M.
 M

anual   operation   with   sequential   changing  
o

f   the   six   gears.Gear selector lever
To select position P,   move   the   gear  s
elector   to   the   highest   position  
(

towards

R), then push it for wards and
then
  to   the   left.
Only
  engage   it   when   the   vehicle   is   at   a  
c

omplete   stop.   In   this   position,   the   front  
w

heels   are   locked.   Ensure   that   the   gear  
s

elector   is   correctly   positioned.
To
  move   the   gear   selector,   switch   on  
t

he   ignition   or   start   the   engine.
If
  the   battery   is   not   sufficiently   charged,  
i

t   is   not   possible   to   move   the   gear  
s

elector.
To come out of position P
, move the
gear   selector   to   the   right   to   the   desired  
p

osition,   while   keeping   your   foot   on   the  
b

rake
 ped
al.
It
 
is
 
possible
 
to
 
change
 
from
 
one
 
mode
 
t

o
 
the
 
other
 
at
 
any
 
time.
With the automated mode, you can
temporarily
 
take
 
control
 
of
 
the
 
gear
 
c

hanges
 
at
 
any
 
time.
Driving

144
C4-Picasso-II_en_Chap04_conduite_ed01-2016
Before switching off the engine, you can change   to   position   P or N   to   be   in   neutral.  
I

n   either   case,   apply   the   parking   brake   to  
i

mmobilise   the   vehicle,   unless   it   is   programmed  
i

n   automatic   mode.
If the lever is not in position P ,
  on   opening   the  
d

river's   door   or   approximately   45   seconds   after  
s

witching   off   the   ignition   there   is   an   audible  
s

ignal   and   a   message   appears:
F
 
m
ove   the   gear   selector   to   position   P;   the  
a

udible   signal   stops   and   the   message  
d

isappears.
Operating fault
Whenever parking, you must apply the parking brake   to   immobilise   the   vehicle,   if   automatic  
o

peration   has   been   deactivated.
Parking the vehicle
In all circumstances, ensure that the
gear  selector   is   in   position   P before
leaving
  your   vehicle. In the event of a fault with the
gearbox,
  the   service   warning   lamp  
c

omes on in the instrument panel,
accompanied   by   a   message   and   an  
a

udible
 s
ignal.
In   this   case   the   gearbox   goes   into   back-up  
m

ode   and   stays   in   3
rd gear. You may then feel a n
oticeable
 
jolt
 
when
 
going   from   P to R and from
N to R .
 
This
 
jolt
 
does
  not   present   any   risk   to   the  
g

earbox.
Do
 
not
 
exceed
 
60
 
mph   (100   km/h)   while   also  
o

bserving
 
legal
 
speed   limits.
Have
 
it
 
checked
 
by
 
a
  CITROËN   dealer   or   a  
q

ualified
 w

orkshop.
In the event of a battery failure, use the
chock
 
to
 
immobilise
 
the
 
vehicle.
Driving

146
C4-Picasso-II_en_Chap04_conduite_ed01-2016
Stop & Start
The Stop & Start system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine   restarts   automatically   -   START   mode   -   as   soon   as   you   want   to   move   off.   The   restart   takes   place   instantly,   quickly   and   silently.
Operation
Going into engine STOP
mode
This indicator lamp comes on in the instrument
panel  and   the   engine   goes   into   standby  
au

tomatically:
-

w
ith a manual gearbox , at speeds below
12
  mph   (20   km/h),   or   vehicle   stationary  
(

with   PureTech   130,   THP   165   and  
B

lueHDi 100, 115 and 120 versions), when
you
  place   the   gear   lever   in   neutral,   and   you  
r

elease the clutch pedal,
-

w
ith an automatic gearbox , with the
vehicle stationary, when you press the
brake
  pedal   or   place   the   gear   selector   lever  
i

n position N . Never
  refuel   with   the   engine   in   STOP  
m

ode;   you   must   switch   off   the   ignition  
w

ith   the   START/STOP   button.
For
  your   comfort,   during   parking  
m

anoeuvres, STOP mode is not
available for a few seconds after
coming
  out   of   reverse   gear.
The Stop & Start system does not affect
the functionality of the vehicle, such as
for
  example,   braking,   power   steering...
Special cases: STOP mode not
available
STOP mode is not invoked when:
-  t he   driver's   door   is   open,
-
 
t
he   driver's   seat   belt   is   not   fastened,
-
 
t
he   vehicle   has   not   exceeded   6   mph  
(10
  km/h)   since   the   last   engine   start   using  
t

he   START/STOP   button,
-
 
t
he   electric   parking   brake   is   applied   or  
be

ing
 a
pplied,
-
 
t
he   engine   is   needed   to   maintain   a  
c

omfortable   temperature   in   the   passenger  
c

ompartment,
-
 
d
emisting   is   selected,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
In this case, this indicator lamp flashes
for  a   few   seconds   then   goes   off.
This operation is perfectly normal.
Per fect
 
for
 
urban
 
use,
 
the
 
Stop
 
&
 
Start
 
system
 
reduces
 
fuel
 
consumption
 
and
 
exhaust
 
emissions
 
as
 
well
  as   the   noise   level   when   stationary.
If your vehicle is fitted with the system, a time
counter calculates the sum of the periods in
STOP
 
mode
 
during
 
a
 
journey.
 
It
 
resets
 
itself
 
to
 
z

ero
 
every
 
time
 
the
 
ignition
 
is
 
switched
 
on
 
with
 t
he
 
START/STOP
 
button.
Driving

147
C4-Picasso-II_en_Chap04_conduite_ed01-2016
Going into engine START mode
This indicator lamp goes off and the engine s tarts a utomatically:
-

w

ith a manual gearbox , when you fully
depress the clutch pedal,
-

w

ith an automatic gearbox :
●
 
g

ear   selector   in   position   D or M, when
you
  release   the   brake   pedal,
●
 
o

r
 
gear   selector   in   position   N   and   brake  
p

edal   released,   when   you   place   the   gear  
s

elector in position D or M ,
●
 
o

r
 
when   you   engage   reverse. START
  mode   is   invoked   automatically   when:
-  y ou   open   the   driver's   door,
-
 
y
ou   unfasten   the   driver's   seat   belt,
-
 
t
he   speed   of   the   vehicle   exceeds   15   mph  
(

25   km/h)   with   a   manual   gearbox   (2   mph  
(

3   km/h)   with   PureTech   130,   THP   165   and  
B

lueHDi 100, 115 and 120 versions) and
2 mph
  (3   km/h)   with   an   automatic   gearbox,
-
 
t
he   electric   parking   brake   is   being   applied,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   for   control   of   a   system.
Special cases: START invoked
automaticallyIn some circumstances, such as the need to
maintain a comfortable temperature in the
passenger  compartment,   it   may   be   necessary  
t

o   deactivate   the   Stop   &   Start   system.
The system can be deactivated at any time,
once
  the   ignition   is   on.
If
  the   engine   is   in   STOP   mode,   it   then   restarts.
The Stop & Start system is automatically
reactivated
  every   time   the   ignition   is  
s

witched on.
Manual deactivation/
reactivation
In this case this indicator lamp flashes
for   a   few   seconds,   then   goes   off.
This operation is perfectly normal. Select
  "Stop   &   Start"   to   deactivate   the   system.
This is confirmed by the illumination
of   this   indicator   lamp.
Using   the   dynamic   cruise   control  
d

eactivates   the   Stop   &   Start   system.
Deactivation of Stop & Start is done in the
Driving
 

menu   of   the   touch   screen   tablet.
Select   "Stop   &   Start"   again   to   reactivate   the  
s

ystem.
This is confirmed by the illumination
of   this   indicator   lamp.
4
Driving

148
C4-Picasso-II_en_Chap04_conduite_ed01-2016
Operating fault
Have it checked by a CITROËN dealer or a qualified w orkshop.
In the event of a fault in STOP mode, the vehicle
may
  stall.
All
  of   the   instrument   panel   warning   lamps   come on.
Depending on version, an alert message may also   be   displayed,   asking   you   to   place   the   gear  
s

elector lever at position N and put your foot on
the
  brake   pedal.
It is then necessary to switch off the ignition and start   the   engine   again   using   the   "START/STOP" b

utton.
In the event of a fault with the system,
this indicator lamp flashes for a few
moments then comes on continuously,
accompanied
  by   a   message.
Opening the bonnet
Before
 
doing
 
anything
 
under
 
the
 
b

onnet, deactivate the Stop & Start
system
 
to
 
avoid
 
the
 
risk
 
of
 
injury
 
related
 
t

o
 
an
 
automatic
 
change
 
to
 
START
 
m

ode.
Driving on flooded roads
Before
 
driving
 
through
 
a
 
flooded
 
road,
 
i

t
 
is
 
strongly
 
recommended
 
that
 
you
 
d

eactivate
 
the
 
Stop
 
&
 
Start
 
system.
For more information on Driving
advice , particularly on flooded roads,
refer
 
to
 
the
 
corresponding
 
section. The Stop & Start system requires a
battery
  of   advanced   technology   and  
sp

ecial
 c
haracteristics.
All
 
work   on   this   type   of   battery   must  
o

nly be done by a CITROËN dealer
or
 
a
  qualified   workshop.
For more information on the
12 V
batter y ,
  refer   to   the   corresponding  
s

ection.
Driving

154
C4-Picasso-II_en_Chap04_conduite_ed01-2016
Steering mounted controls
6. Speed  limiter   on   /   pause   indication.
7. S peed   limiter   mode   selection   indication.
8.
 S

peed   limiter   setting.
Speed limiter - "LIMIT"
System which prevents the vehicle from exceeding the speed programmed by the driver.
The speed limiter cannot, in any
circumstances, replace the need to
observe speed limits, nor can it replace the
need
  for   vigilance   on   the   part   of   the   driver.
Once the programmed speed limit is reached, additional pressure on the accelerator pedal
has
  no   effect.
1.
 S

elect   speed   limiter   mode.
2.
 L

ower   programmed   speed.
3.
 R

aise   programmed   speed.
4.
 S

peed   limiter   on   /   pause.
5.
D

isplay the list of memorised speeds or,
 D

isplay   the   list   of   memorised   speeds.Displays in the instrument panel
Switching on the speed limiter requires
a   programmed   speed   of   at   least   20   mph  
(

30 km/h).
The speed limiter is paused by operation of the
control.
The
  programmed   speed   can   be   exceeded  
t

emporarily   by   pressing   the   accelerator   firmly  
b

eyond   the   point   of   resistance.
To
  return   to   the   programmed   speed,   simply  
r

elease the accelerator pedal until the vehicle
returns
  to   the   programmed   speed   limit.
The
  programmed   speed   remains   in   the
 m

emory   when   the   ignition   is   switched   off.For more information on Memorising speeds ,
refer
  to   the   corresponding   section.
For more information on Speed limit
recognition and memorisation, refer to the
corresponding
 s

ection.
Driving

157
C4-Picasso-II_en_Chap04_conduite_ed01-2016
Steering mounted controls
6. Cruise  control   pause   /   resume   indication.
7. C ruise   control   mode   selection   indication.
8.
 Spe

ed
 s
etting.
Cruise control - "CRUISE"
System which automatically maintains the speed of the vehicle at the value programmed by the driver, without any action on the accelerator pedal.
The cruise control system cannot, in any circumstances, replace the need to observe speed limits, nor can it replace the need for vigilance on the part of the driver.
Y ou   are   advised   to   keep   your   feet   near   the   pedals   at   all   times.
Switching on the cruise control requires a
minimum   vehicle   speed   of   25   mph   (40   km/h).
As
  well   as   engagement   of:
-
 
f
ourth   gear   or   higher   on   a   manual   gearbox,
-
 
s
econd   gear   or   higher   in   manual   mode   on  
a

n   automatic   gearbox,
-
position D
  on   an   automatic   gearbox.
The
  system   remains   active   after   changing   gear  
o

n   vehicles   with   a   manual   gearbox   and  
Stop
  &   Start.
The cruise control is paused
 

by   pressing  
b

utton 4   or   the   brake   pedal   or   on   triggering   of  
t

he   ESC   system   for   safety   reasons.
It
  is   possible   to   exceed   the   programmed   speed  
t

emporarily   by   pressing   the   accelerator   pedal.
To
  return   to   the   programmed   speed,   simply  
r

elease the accelerator pedal until the
programmed
  cruise   speed   is   reached   again.1.
 S

elect   cruise   control   mode.
2.
S

et the current speed of the vehicle
as
  the   programmed   speed   /   Lower   the  
pro

grammed
 s
peed.
3.
S

et the current speed of the vehicle
as
  the   programmed   speed   /   Raise   the  
pro

grammed
 s
peed.
4.
 P

ause   /   resume   cruise   control.
5.
D

isplay the list of memorised speeds or,
 A

ccept   the   speed   suggested   by   the   speed  
l

imit   recognition   system.Displays in the instrument panel
Switching off the ignition cancels any programmed   speed   value. For more information on Memorising speeds
,
refer   to   the   corresponding   section.
For more information on Speed limit
recognition and memorisation, refer to the
corresponding
 s
ection.
4
Driving

161
C4-Picasso-II_en_Chap04_conduite_ed01-2016
The dynamic cruise control is switched on
manually:   it   requires   that   the   speed   of   the  
v

ehicle be between 25 and 90 mph (40 and
150 km/h),
  as   well   as   the   engagement   of:
-
 
f
ourth   gear   or   higher   with   a   manual  
g

earbox,
-
 
s
econd   gear   or   higher   with   an   automatic  
g

earbox   in   manual   mode,
-
position D
  with   an   automatic   gearbox.
The
  system   remains   active   after   changing   gear  
o

n   vehicles   with   a   manual   gearbox   and  
Stop
  &   Start.
General points
The dynamic cruise control can be paused
manually o r a utomatically:
-
 
b
y   pressing   button   4,
-
 
b
y   pressing   the   brake   pedal,
-

i
n the event of operation of the ESC, for
safety reasons,
-

i
n the event of operation of the electric
parking
  brake   control   lever,
-

w
hen an inter-vehicle time threshold is
reached
  (calculated   according   to   the  
r

elative speeds of your vehicle and the
vehicle in front and the inter-vehicle time
setting
 c

hosen),
-

w
hen the distance between your vehicle
and the one in front becomes too small,
-

w
hen the speed of the vehicle in front is too
low,
-

w
hen the speed of your vehicle becomes
too
  low.
The dynamic cruise control cannot in any
circumstances replace the observation
of
 sp

eed
 l

imits,
 n

or
 t

he
 n

eed
 fo

r
 v

igilance
 o

n
 
the
 
part
 
of
 
the
 
driver.
It
 
is
 
recommended
 
that
 
you
 
always
 
keep
 y

our
 
feet
 
close
 
to
 
the
 
pedals.
If
 
the
 
speed
 
setting
 
selected
 
is
 
above
 
9

0
 
mph
 
(150
 
km/h),
 
the
 
system
 
switches
 
t

o standard cruise control operation,
with
 
no
 
adjustment
 
of
 
the
 
inter-vehicle
 
s

afe
 
distance
 
(a
 
message
 
appears
 
in
 
t

he
 
instrument
 
panel). The
  inter-vehicle   time   setting   is   kept   in  
m

emory   on   switching   off   the   ignition.
The dynamic cruise control operates by
day
 
and
 
at
 
night,
 
in
 
fog
 
or
 
in
 
moderate
 
r

ainfall.
The system does not act on the braking s ystem,   but   works   only   with   engine   braking.
The
  regulation   range   is   limited:   there   will
 n

o   longer   be   any   adjustment   of   speed   if   the
 d

ifference   between   the   programmed   speed
 s

etting   and   the   speed   of   the   vehicle   in   front
 b

ecomes   too   high   (18   mph   (30   km/h)).
If the difference between the
programmed  speed   setting   and   the  
s

peed of the vehicle in front is too
great,
  the   speed   cannot   be   adjusted:  
t

he cruise control is automatically
deactivated.
4
Driving

169
C4-Picasso-II_en_Chap04_conduite_ed01-2016
Switching on
The cruise control is switched on manually,
it requires a vehicle speed of between 18 and
112 mph
  (30   and   180   km/h).
An
  automatic   gearbox   must   be   in   position   D
or M . Other wise,
  the   last   setting   made   will   be   used  
w

hen   switching   on   the   system.
Switching   off   the   ignition   cancels   any  
p

rogrammed   speed   setting.
When   the   cruise   control   is   operating,  S
top & Start is automatically
deactivated.
Pause
The dynamic cruise control can be paused
manually b y:
-
 
a
ction   by   the   driver:
●
 
o
n   button   4,
●
 
o
n   the   brake   pedal,
●
 
o
n   the   electric   parking   brake   control,
●
 
w
hen   changing   from   D to N with an
automatic
  gearbox.
-

o
r automatically, if operation of the ESC
system
  is   triggered   for   reasons   of   safety.
Following
  braking   of   the   vehicle  
b

ringing   it   to   a   complete   stop,   the  
s

ystem   holds   the   vehicle   stationary   ;  
t

he   cruise   control   is   paused.   The   driver  
s

hould press the accelerator pedal to
move off, then reactivate the system
by
  exceeding   18   mph   (30   km/h)   and  
p

ressing   button   2, 3 or 4 .
If
  the   driver   takes   no   action   following  
t

his   immobilisation,   the   electric   parking  
b

rake   is   applied   automatically   after   a  
f

ew
 m
inutes.
F
 
W

ith
 
the
 
ignition
 
on,
 
turn
 
the
 
thumbwheel 1
to the " CRUISE "
 
position:
 
cruise
 
control
 
m

ode
 
is
 
selected,
 
but
 
not
 
started
 
(grey).
F
 
V

ehicle
 
moving,
 
press
 
one
 
of
 
the
 
buttons 2
or 3 :
 
the
 
current
 
speed
 
of
 
your
 
vehicle
 
b

ecomes
 
the
 
cruise
 
speed
 
setting.
The
 
cruise
 
control
 
is
 
activated
 
(green).
By default, the inter-vehicle distance is set at
" Normal "
 
(2
 
dashes).
4
Driving