Citroen C5 2012 (RD/TD) / 2.G Manual Online

IV
79
ACCESS
BOOT (SALOON)


)
Press upwards on lever 1
and lift
up the boot lid.

With the vehicle stationary, this is
carried out using:


- The remote control.

- The key in a door lock.

- The interior central locking/ un-
locking control.
The boot automatically locks when
the vehicle is moving at a speed of
over 6 mph (10 km/h), even if auto-
matic central locking is deactivated.
It is unlocked when a door is opened
or when the central locking button is
pressed (speed lower than 6 mph
(10 km/h)).


Opening

Locking/unlocking





Emergency boot release
System for mechanical unlocking of
the boot in the event of a battery or
central locking malfunction.

Unlocking


)
Fold back the rear seats to gain
access to the lock from inside
the boot.

)
Insert a small screwdriver into
hole A
of the lock to unlock the
tailgate.

)
Push the white part, located in-
side the lock, to the left to unlock
the boot.


Locking the front and rear
passenger doors


)
Open the doors.

)
On the rear doors, check that
the child lock is not on (see Child
Safety).

)
Remove the black cap, located
on the edge of the door, using
the key.

)
Insert the key in the socket with-
out forcing it, then without turn-
ing it, move the latch sideways
towards the inside of the door.

)
Remove the key and refi t the
cap.

)
Close the doors and check that
the vehicle has locked correctly
from the outside.


Unlocking the front and rear
passenger doors


)
Pull the interior door opening
control.

IV
80
ACCESS

Electric opening BOOT
(TOURER)

Manual opening



)
Press upwards on lever A
and lift
up the tailgate.



)
Press upwards on lever A
, or
press button B
of the remote
control. Do not attempt to help the opening
of the tailgate manually after press-
ing the control A
.


Manual closing



)
Lower the tailgate using the inte-
rior handle C
.



Electric closing



)
Press the push-button D
to close
the tailgate.
Do not interrupt the closing of the
tailgate; if any obstacle prevents it
closing, the operation will stop and
the tailgate will automatically rise
by a few centimetres.


Locking/unlocking

With the vehicle stationary, this is
carried out using:


- The remote control.

- The key in a door lock.

- The interior central locking/ un-
locking control.


Interrupting the opening /
closing of the tailgate
When the tailgate is being opened or
closed electrically, you can interrupt
its movement at any point by press-
ing push-button D
, the control A
or
button B
.
You can then open or close the tail-
gate electrically or manually, if neces-
sary moving it in the opposite direction
to release it. The boot automatically locks when
the vehicle is moving at a speed of
over 6 mph (10 km/h), even if auto-
matic central locking is deactivated.
It is unlocked when a door is opened
or when the central locking button
is pressed (at a speed of less than
6 mph (10 km/h)).


Memorisation of an
intermediate position
You can store an opening angle for
the tailgate:


)
Manually or automatically move
the tailgate to the required posi-
tion.

)
Make a long press on push-but-
ton D
. The system emits a short
audible beep.

)
Release the push-button D
.

IV
81
ACCESS

Cancelling the memorisation

With the tailgate in the intermediate
position, you can cancel the stored
position:


)
Make a long press on push-
button D
. The system emits a
long audible beep.

)
Release the push-button D
. The
tailgate will return to the fully
open position at the next use.



Electrical protection of the
motor
If the tailgate is repeatedly opened
and closed in quick succession, the
motor can start to overheat and then
cut out, preventing opening and
closing of the tailgate.
Allow the motor to cool down for ten
minutes without opening or closing
the tailgate.
Closing in manual back-up mode re-
mains possible.
To avoid risk of injury, make sure
that no one is in the vicinity of the
boot while opening and closing.
If the tailgate is carrying extra
weight (snow, bicycle carrier, etc.)
there is a risk of it closing under
this load. Support the tailgate or
fi rst unload the bicycle carrier or
clear the snow.
When using an automatic car wash, don’t forget to lock the vehicle so
as to avoid any risk of motorised
opening of the tailgate.

IV
82
ACCESS
PANORAMIC SUNROOF (SALOON)

Sunroof closed


- Press B
to fi rst notch: tilting.

- Press B
to second notch: auto-
matic complete tilting.

- Press A
to fi rst notch: sliding to-
wards rear.

- Press A
to second notch: auto-
matic total sliding towards rear.

Sunroof open


- Press B
to fi rst notch: closure.

- Press B
to second notch: auto-
matic total closure.


Always remove the ignition key
when leaving the vehicle, even if
for a short time .
In the event of anything being
caught by the sunroof closing, you
must reverse the roof movement.
Do this by reversing the position of
the control switch .
When the driver is operating the
sunroof, they must always make
sure that the passengers are not
preventing it from closing properly.
The driver must ensure that pas-
sengers use the sunroof control
correctly.
Pay special attention to where chil-
dren are when operating the sun oof.
The fi tting of a sunroof as an ac-
cessory is prohibited


Operation


Tilted sunroof


- Press A
to fi rst notch: closure.

- Press A
to second notch: auto-
matic total closure.

Your sun roof is fi tted with a manually-
operated blind.


Anti-pinch

An anti-pinch device stops the sun
roof from closing, whether sliding or
tilting. If it meets an obstacle, it re-
opens.


Reinitialisation


After a battery disconnection or if
there has been a malfunction, you
have to re-initialise the anti-pinch
function.


)
move control B
until the roof is in
the complete tilting position,

)
keep control B
pressed down for
a minimum of 1 second.

During these operations, the anti-
pinch function does not operate

.

IV
83
ACCESS
PANORAMIC SUNROOF (TOURER)
This comprises a tinted glass pan-
oramic area 1
to improve brightness
and vision in the passenger com-
partment.
It is fi tted with an electric blind 2
to
help maintain a comfortable temper-
ature and reduce noise.

Opening



)
Press control A
.
Pressing to the 1st notch
allows you
to open the blind step by step.
Pressing to the 2nd notch
allows
you to fully open the blind.
The blind stops in the closest pre-
defi ned position (11 positions) as
soon as you release the control.


Closing



)
Press control B
.
Press to the fi rst notch
to close the
blind step by step.
Press to the second notch
to close
the blind completely.
The blind stops at the nearest pre-
set position (11 positions) as soon
as you release the control. After a battery disconnection, or if
there has been a malfunction, you
have to re-initialise the anti-pinch
function:


)
press control B
to the 2nd notch
(fully closed),

)
wait until the blind is fully
closed,

)
press control B
for at least
3 seconds.
If the blind opens randomly during a
closing operation, and straight after
the blind stops:


)
Press control B
until the blind
closes fully.

During these operations, the anti-
pinch function does not operate.



In the event of anything being
caught when the blind is moving,
you must reverse the movement of
the blind. To do so, reverse the po-
sition of the control.
When the driver is operating the
blind, he or she must always make
sure that the passengers are not
preventing it from closing properly.
The driver must ensure that pas-
sengers use the blind correctly.
Pay particular attention to children
when operating the blind .



Anti-pinch

If the blind meets an obstacle whilst
closing, it stops and opens partially
again.
You must re-initialise the anti-pinch
function within 5 seconds of the
blind stopping:


)
press control B
until the blind is
fully closed (closing in steps of a
few centimetres).

SEQUENTIAL ELECTRIC
BLIND

IV
!
84
ACCESS
FUEL TANK

Capacity of the tank: approxi-
mately
71 litres

*
.



Low fuel level

When the minimum level
in the tank is reached, this
warning lamp comes on
in the instrument panel,
accompanied by an audible warning
and a message on the multifunction
screen. When it fi rst comes on, there
remains around 5 litres of fuel in the
tank.
You must refuel to avoid running out
of fuel.


)
Press at the top left corner, then
pull open from the left.


)
turn the key a quarter turn to lock
and unlock the fi ller cap,

)
when refuelling, place the cap on
hook A
,

)
fi ll the tank, but do not persist
after the third cut-off
; this could
cause your vehicle to malfunc-
tion.


While you are refuelling, the engine must be stopped and the ignition
switched off.


For a petrol engine with a cata-
lytic converter, unleaded fuel is
compulsory.



Opening the fuel flap

Additions of fuel must be of at least
5 litres to be taken into account by
the fuel gauge.
The fi ller neck is narrower to ensure
that only unleaded petrol nozzles
can be put in.
Opening the fi ller cap may create
a noise of an inrush of air. This
vacuum, which is entirely normal,
is caused by the sealing of the fuel
system.


Refuelling








With Stop & Start, never re-
fuel with the system in STOP
mode; you must switch off
the ignition with the key.

*
55 litres for Slovakia.

IV
85
ACCESS










Quality of the fuel used for
petrol engines

The petrol engines are perfectly
compatible with E10 type petrol
biofuels (containing 10% ethanol),
conforming to European standards
EN 228 and EN 15376.
E85 type fuels (containing up to 85%
ethanol) are reserved exclusively for
vehicles marketed for the use of this
type of fuel (BioFlex vehicles). The
quality of the ethanol must comply
with European standard EN 15293.
For Brazil only, special vehicles are
marketed to run on fuels containing
up to 100% ethanol (E100 type).













Quality of the fuel used for
Diesel engines

The Diesel engines are perfectly
compatible with biofuels which con-
form to current and future European
standards (Diesel fuel which com-
plies with standard EN 590 mixed
with a biofuel which complies with
standard EN 14214) available at the
pumps (containing up to 7 % Fatty
Acid Methyl Ester).
The B30 biofuel can be used in cer-
tain Diesel engines; however, this
use is subject to strict application
of the special servicing conditions.
Contact a CITROËN dealer or a
qualifi ed workshop.
The use of any other type of (bio)fuel
(vegetable or animal oils, pure or di-
luted, domestic fuel...) is strictly pro-
hibited (risk of damage to the engine
and fuel system).

MISFUEL PREVENTION (DIESEL)
*

Mechanical device which prevents
fi lling the tank of a Diesel vehicle
with petrol. It avoids the risk of en-
gine damage that can result from fi ll-
ing with the wrong fuel.
Located in the fi ller neck, the misfuel
prevention device appears when the
fi ller cap is removed.


Operation

When a petrol fi ller nozzle is intro-
duced into the fuel fi ller neck of your
Diesel vehicle, it comes into contact
with the fl ap. The system remains
closed and prevents fi lling.

Do not persist but introduce a
Diesel type fi ller nozzle.


It remains possible to use a fuel
can to fi ll the tank.
In order to ensure a good fl ow of
fuel, do not place the nozzle of the
fuel can in direct contact with the
fl ap of the misfuel prevention de-
vice and pour slowly.
* According to country of sale.

Travelling abroad
As Diesel fuel pump nozzles may
be different in other countries, the
presence of the misfuel prevention
device may make refuelling impos-
sible.
Before travelling abroad, we rec-
ommend that you check with the
CITROËN dealer network, whether
your vehicle is suitable for the fuel
pumps in the country in which you
want to travel.

V
86
VISIBILITY
EXTERIOR LIGHTING
CONTROLS
Control stalk for the selection and
control of the various front and rear
lamps providing the vehicle's lighting.

Main lighting

The various front and rear lamps of
the vehicle are designed to adapt
the driver's visibility progressively in
relation to the climatic conditions:


- sidelamps, to be seen,

- dipped beam headlamps to see
without dazzling other drivers,

- main beam headlamps to see
clearly when the road is clear.



Additional lighting

Other lamps are fi tted to fulfi l the re-
quirements of particular driving con-
ditions:


- a rear foglamp to be seen from a
distance,

- front foglamps for even better
forward vision,

- directional headlamps for im-
proved visibility when cornering,

- daytime running lamps to be
seen during the day.



Settings

Various automatic lighting control
modes are also available depending
on options:


- daytime running lamps,

-
automatic illumination of headlamps,


- directional lighting,

- guide-me-home lighting.



Manual controls

Lamps off.





Automatic illumination of
headlamps.
Sidelamps.
Dipped headlamps or
main beam headlamps.

B.

Stalk for switching headlamps: pull
the stalk towards you to switch the
lighting between dipped and main
beam headlamps.
In the lamps off and sidelamps
modes, the driver can switch on the
main beam headlamps temporarily
("headlamp fl ash") by maintaining a
pull on the stalk.

Displays

Illumination of the corresponding indicator
lamp in the instrument panel confi rms that
the lighting selected is on.

The lighting is controlled directly by
the driver by means of the ring A

and the stalk B
.
A.
Main lighting mode selection ring:
turn it to position the symbol re-
quired facing the mark.
In some weather conditions (e.g. low
temperature or humidity), the pre-
sence of misting on the internal sur-
face of the glass of the headlamps
and rear lamps is normal; it disap-
pears after the lamps have been on
for a few minutes.

V
87
VISIBILITY









C.
Foglamps selection ring.
The foglamps operate with the side-
lamps and the dipped and main
beam headlamps.


-
1 st turn forwards: rear foglamps on.


- 1

st turn rearwards: rear foglamps off.




- 1 st
turn forwards: front foglamps on.

- 2 nd
turn forwards: rear foglamps on.

- 1 st
turn rearwards: rear foglamps off.

- 2 nd
turn rearwards: front foglamps off.



Model with rear
foglamps only
Model with front and rear
foglamps





In good or rainy weather, both day
and night, use of the front foglamps
and the rear foglamps is prohibited.
In these situations, the power of
their beams may dazzle other dri-
vers. They should only be used in
fog or falling snow.
In these weather conditions, it is
your responsibility to switch on the
foglamps and dipped headlamps
manually as the sunshine sensor
may detect suffi cient light.
Do not forget to switch off the front
and rear foglamps when they are
no longer needed.

Lighting left on
When a front door is opened with
the ignition off and in manual light-
ing mode, an audible signal warns
the driver if the vehicle's lighting is
still on.
In this case, switching off the light-
ing stops the audible signal.
With the ignition off, if the dipped
headlamps remain on, they will
switch off automatically after thirty
minutes to prevent discharging of
the battery.

V
88
VISIBILITY

*
According to country.







Daytime-running lamps

System which switches on special
lamps at the front, to make the vehi-
cle more visible by day.
They light up automatically and perma-
nently, when the engine is running, if:


- The function is activated * in the
"Main Menu" of the instrument
panel screen.

- The lighting control is at position 0

or AUTO
.

- All the headlamps are off.
You can deactivate * this function
using the "Main Menu" of the instru-
ment panel screen.






Manual guide-me-home
lighting
Temporarily keeping the dipped
beam headlamps on after the vehi-
cle's ignition has been switched off
makes the driver's exit easier when
the light is poor.

Switching on


)
With the ignition off, "fl ash" the
headlamps using the lighting stalk.

)

A further "headlamp fl ash" switches
the function off.



Switching off
The manual guide-me-home lighting
switches off automatically after a set
time.














Automatic illumination
of headlamps
The sidelamps and dipped beam headlamps
are switched on automatically, without any ac-
tion on the part of the driver, when a low level
of external light is detected or in certain cases
of activation of the windscreen wipers.
As soon as the brightness returns to a suffi -
cient level or after the windscreen wipers are
switched off, the lamps are switched off auto-
matically.

Activation


)

Turn ring A
to the "AUTO"
position.
The automatic illumination of head-
lamps is accompanied by a message
in the instrument panel screen.



Deactivation


)
Turn ring A
to a position other
than "AUTO"
. Deactivation is
accompanied by a message in
the instrument panel screen.