Citroen C8 2008.5 1.G Repair Manual

Page 61 of 250

66
Seats

3 - Seat back angle adjustment
Tilt the control to the front or the rear to obtain the angle required.
The electrical functions of the seats are cancelled one minute after the ignition has been switched off.

4 - Driver’s seat lumbar adjustment (mechanical)
Raise or lower the lever to obtain the correct position.
5 - Head restraint height and angle adjustment (manual)
To raise or lower the head restraint, pull it forwards, then slide it.

Never drive with the head restraints removed; they must be in place and correctly adjusted.
6 - Rotating of seats (mechanical)
Place the seat back in the upright position.
Place the seat in the highest intermediate longitudinal position.
On the driver’s side, push the steering wheel, apply the handbrake. To allow rotation of the seat, lower the handbrake handle pulling on the end.
Pull the control upwards and rotate the seat inwards.
This rotating operation must be carried out with the engine switched off. The handbrake, the lever of which is now in the lower position, remains applied. Do not forget to raise the lever and release the brake before setting off.
Driving with a passenger seated facing the rear is prohibited.

For further information regarding the disengaging of the handbrake, refer to the "Driving safety" section of chapter 5.

The setting is correct when the upper edge of the head restraint is level with the top of the head.
To remove the head restraint, place it in the high position, lift the tab using a coin and pull upwards and forwards at the same time.
To re-install, engage the head restraint rods in the holes, making sure they are aligned with the seat back.

Page 62 of 250

ERGONOMICS and COMFORT
3
67
Seats
Memorising seat positions
Two driving positions can be memorised, using buttons M/1and M/2 .
These are located on the side of the seat:
 Place the ignition key in the "running" position (2nd notch),
 Adjust your seat,
 Press button M , then button 1 for a fi rst driving position within four seconds.
Repeat the same actions on buttons Mand 2 to store another driving position.
An audible signal confi rms that a position has been memorised.
Memorising a new position cancels the
previous one.
Activating a memorised driving
position
Front heated seat controls
When the engine is running, the front seats can be heated separately.
Use the adjustment controls located on the side of each front seat to switch on and select the self-regulated level of heating:

1: Low.

2: Medium.

3: High.

0: Off. After recalling a memorised position fi ve times in succession, the function will be cancelled until the engine is started.

Engine running
 Keep button 1 or 2 pressed down until the end of setting of the corresponding memorised position.

Engine off
 Briefl y press button 1 or 2 to recall the corresponding memorised position.

Page 63 of 250

68
Seats
Rear bench seat
One three-seat bench seat, row 3.
Rear side seats
Two rear passenger seats, left and right side position,
rows 2 and 3.
Rear centre seat
One rear passenger seat, row 2 central position and row
3 left side position. Integrated seat belt. Plastic shell t
rim.
Folds to the low table position.
Captain’s Chair seat
Equipment dedicated to the special version of the C8.
Four rear passenger seats with armrests.
Side position, rows 2 and 3.

Page 64 of 250

ERGONOMICS and COMFORT
3
69
Seats
REAR SIDE SEATS

Forwards/backwards adjustment
Lift bar A and slide the seat forwards or backwards.

Handling the side seat
Adjusting the angle of the seat back
Push lever B upwards and adjust the angle as required.
Release the lever to lock.

Access to row 3
1. Place the head restraint in the low position.
2. Push lever B upwards as far as possible.

Exit from row 3
1. Place the head restraint in the low position.
2. Pull control C .
3. Guide the tilting of the seat back forwards until the rear anchorages are unlocked. If you experience any diffi culty, use the red emergency control to unlock the anchorages.
4. Place the seat in the vertical closed position.

Following each entry or exit, reposition the raised seat guiding it until the rear anchorages lock in their rails.

3. Fold the seat back onto the seat cushion and guide the tilting of the seat back forwards until the rear anchorages are unlocked. If you experience any diffi culty, use the emergency control to unlock the anchorages.
4. Place the seat in the vertical closed position.

Page 65 of 250

70
Seats

Control for sliding the rear side seats from row 3 or the boot
Pull the strap (marked with the arrow symbol) to slide the seat in front of you.

Removing the side seat

1. Tilt the seat back forwards to detach the rear anchorages.
2. Grab the red strap which appears and pull it upwards, the front anchorages unlock .
3. The strap, like the handle, enables you to remove the seat.

Refi tting the side seat
Check that there is no obstacle obstructing the slides or preventing correct locking of the seat anchorages.

1. Place the front anchorages at the front stop in the slides. Support the strap fi rmly for easier positioning of the seat.
2. Tilt the folded seat towards the rear. The rear anchorages lock.
3. Raise the seat back.
4. Slide the seat .

Page 66 of 250

ERGONOMICS and COMFORT
3
71
Seats
ROW 2 CENTRE SEAT
This can be placed in row 3, on the left.
"Low table" position
1. Place the head restraint in the low position.
2. At the top (at the back of the seat), lift the handle identifi ed by the symbol and guide the tilting of the seat back towards its seat cushion.

3. You have a "low table". To return to the seat position, lift the handle and guide the raising of the seat back.

Removing the centre seat
1. Place the seat in the "low table" position.
2. Using the control which you pull, tilt the seat back forwards so releasing the rear anchorages from the slides.
3. Grab the red strap which appears and pull it upwards, the front anchorages unlock .
4. The strap, like the handle, enables you to remove the seat.

Page 67 of 250

72
Seats Rear head restraints
The rear head restraints can be removed and have two positions:
 high, position for use,
 low, storage position.
To raise or lower a head restraint, pull it forwards sliding it at the same time.
To remove it, place it in the high position, push the lug and pull it forwards and upwards.
To refi t it, engage the head restraint
rods in the holes taking care to remain
in the centreline of the seat back.


Never drive with the head restraints removed, they must be in place and correctly adjusted.

Refi tting the centre seat
Check that there is no obstacle obstructing the slides or preventing correct locking of the seat anchorages.

1. Place the front anchorages at the front stop in the slides. Support the strap fi rmly for easier positioning of the seat.
2. Tilt the folded seat towards the rear. The rear anchorages lock.
3. Raise the seat back and slide the seat.

Turning a rear seat round
The rear seats can be placed in a "face to face" position.
Carry out the operations described for removal then turn the seat round and resume with the procedure for refi ttingthe seat .

This turning operation must be carried out when stationary.
Driving with a passenger seated facing the rear is prohibited.
When the vehicle is being driven, placing a row 2 seat in the closed position while a passenger is sitting in row 3 is prohibited.

Page 68 of 250

72
Seats Rear head restraints
The rear head restraints can be removed and have two positions:
 high, position for use,
 low, storage position.
To raise or lower a head restraint, pull it forwards sliding it at the same time.
To remove it, place it in the high position, push the lug and pull it forwards and upwards.
To refi t it, engage the head restraint
rods in the holes taking care to remain
in the centreline of the seat back.


Never drive with the head restraints removed, they must be in place and correctly adjusted.

Refi tting the centre seat
Check that there is no obstacle obstructing the slides or preventing correct locking of the seat anchorages.

1. Place the front anchorages at the front stop in the slides. Support the strap fi rmly for easier positioning of the seat.
2. Tilt the folded seat towards the rear. The rear anchorages lock.
3. Raise the seat back and slide the seat.

Turning a rear seat round
The rear seats can be placed in a "face to face" position.
Carry out the operations described for removal then turn the seat round and resume with the procedure for refi ttingthe seat .

This turning operation must be carried out when stationary.
Driving with a passenger seated facing the rear is prohibited.
When the vehicle is being driven, placing a row 2 seat in the closed position while a passenger is sitting in row 3 is prohibited.

Page 69 of 250

ERGONOMICS and COMFORT
3
73
Seats
REAR BENCH SEAT
From the boot, you can pull on strap B and slide the seat forwards to make it easier to load the vehicle.

The rear bench seat must only be fi tted in row 3.
Seat back folded position
1. Place the head restraints in the low position.
2. Pull the strap C upwards, from the tailgate.

3. Tilt the seat back on the seat cushion.

Vertical position of the bench seat
1. Place the head restraints in the low position.
2. Pull the strap C upwards, from the tailgate.
3. Fold the seat back onto the seat cushion .
4. Pull the lever D to unlock the rear anchorages.
5. Place the seat in the vertical "folded" position.
When driving, attach the retaining straps to the handles.
Forwards/backwards
adjustment
From the seat cushion, lift bar
A and
slide the seat towards the front or
the rear.

Page 70 of 250

74
Seats

Removing the bench seat
1. Fold the seat to the vertical position.
2. Grasp the two bars E underneath the seat .
3. The front anchorages unlock.
Refi tting the bench seat
For removal and refi tting, pass the rear seat, in the "folded" position, through the sliding side doors.
Check that there is nothing blocking the runners which could prevent correct locking of the bench seat anchorages.
1. Position the front anchorages at the front stop of the runners.
2. Tilt the folded seat rearwards.
3. The rear anchorages then lock.
4. Unlock the seat back and lift it using the strap C . Good practice
When the vehicle is being driven, it is prohibited for a passenger to sit:
-
in row 3 if the seat back in front
(row 2) is in the table position.
- in row 3 if the seat/bench in front
(row 2) is in the vertical folded
position.
- in the centre seat if the right-hand
side seat is in the vertical folded
position.

Page:   < prev 1-10 ... 21-30 31-40 41-50 51-60 61-70 71-80 81-90 91-100 101-110 ... 250 next >