CITROEN DS3 CABRIO DAG 2015 Handbook (in English)

39
DS3_en_Chap01_controle-de-marche_ed01-2014
on vehicles fitted with an electric oil level
indicator,  information   on   the   oil   level   is  
d

isplayed   in   the   instrument   panel   for   a   few  
s

econds   when   the   ignition   is   switched   on,   after  
t

he   service   information.
Engine oil level indicator*
The level shown will only be correct
if  the   vehicle   is   on   level   ground   and  
t

he   engine   has   been   off   for   more   than  
3

0 minutes.
Oil level correct
Oil level low
This is indicated by the flashing of " O I L" ,
a ccompanied   by   illumination   of   the   service  
w

arning   lamp,   an   audible   signal   and   a  
m

essage.
If
  the   low   oil   level   is   confirmed   by   a   check   using  
t

he   dipstick,   the   level   must   be   topped   up   to  
p

revent   damage   to   the   engine.
Refer
  to   the   "Checking   levels"   section.
Oil level indicator fault
This is signaled by the flashing of "OIL- -".
C ontact a CITRoË N dealer or a qualified
workshop.
In the event of a fault with the electric oil level
indicator,
  the   engine   oil   level   is   no   longer  
mon

itored.
While
  the   system   is   faulty,   you   should   check  
t

he   engine   oil   level   using   the   manual   dipstick  
l

ocated   under   the   bonnet.
Refer
  to   the   "Checking   levels"   section.
*
  Depending   on   version.
Monitoring

DS3_en_Chap01_controle-de-marche_ed01-2014
The total and trip distances are displayed for
thirty  seconds   when   the   ignition   is   switched   off,  
w

hen the driver's door is opened and when the
vehicle
  is   locked   or   unlocked.
distance recorders
Total distance recorder
It measures the total distance travelled by the vehicle   since   its   first   registration.
When
 
traveling
 
abroad,
 
you
 
may
 
h

ave
 
to
 
change
 
the
 
units
 
of
 
distance:
 
t

he
 
display
 
of
 
road
 
speed
 
must
 
be
 
in
 
t

he
 
official
 
units
 
(miles
 
or
 
km)
 
for
 
the
 
c

ountry.
 
The
 
change
 
of
 
units
 
is
 
done
 v
ia
 
the
 
screen
 
configuration
 
menu,
 
with
 t
he
 
vehicle
 
stationary.
Trip distance recorder
It measures the distance travelled since it was r
eset   to   zero   by   the   driver.
F
 
W
ith   the   ignition   on,   press   the   button   until  
z

eros   appear.

41
DS3_en_Chap01_controle-de-marche_ed01-2014
Black panel
System allowing certain displays to be switched off   for   night   driving.
The
  instrument   panel   remains   illuminated   with  
o

nly the vehicle speed and cruise control or
speed
  limiter   information,   if   in   use.
If
  there   is   an   alert   or   a   change   in   a   function  
o

r   to   a   setting,   the   black   panel   mode   is  
i

nterrupted.Activation
F With   the   lighting   on,   press   the   left   hand  b
utton   of   the   instrument   panel   several  
t

imes   to   progressively   reduce   the  
d

ashboard   lighting   level.
F
 
P
ress   the   button   again   to   reduce   the  
l

ighting   to   the   minimum   level   and   switch   off  
t

he   interior   mood   lighting.
F
 
P
ress   the   button   again   to   activate   the   black  
pan

el.
System
 
for
 
manual
 
adjustment
 
of
 
the
 b
rightness
 
of
 
the
 
instruments
 
and
 
controls
 
in
 r
elation
 
to
 
the
 
exterior
 
brightness.
Lighting dimmer
Activation
When the lighting is on:
F  p ress   the   button   to   change   the   brightness  
o

f   the   instruments   and   controls,
F
 
w
hen   the   level   of   brightness   required   is  
r

eached,   release   the   button.
deactivation
When the lighting is off, or in day mode on vehicles   fitted   with   daytime   running   lamps,  
p

ressing   the   button   does   not   have   any   effect.
Monitoring

DS3_en_Chap01_controle-de-marche_ed01-2014
Trip computer
Monochrome screen A
Information displays
F Press the button, located at the end of the wiper stalk ,
  to   display   the   various   items   of  
t

rip   computer   information   in   succession.The
  trip   computer   provides   the   following  
i

nformation:
-
 ra
nge,
-  
c
urrent   fuel   consumption,
-  
S
top   &   Start   time   counter,
- d istance travelled,
-  
a
verage   fuel   consumption,-
 a

verage
 s
peed.
F  
T
he   next   press   then   returns   you   to   the  
n

ormal
 d
isplay.
System   that   gives   you   information   on   the   current   journey   (range,   fuel   consumption…).
Zero reset
F Press
  the   control   for   more   than   two  s
econds to reset to zero the distance
travelled,
  the   average   fuel   consumption  
a

nd   the   average   speed.

43
DS3_en_Chap01_controle-de-marche_ed01-2014
Monochrome screen c
Information displays
F Press the button, located at the end of the wiper stalk , to display the various trip
computer
  tabs   in   succession. -
 
t
he   current   information   tab  
w

ith:
●  
t
he   range,
●  
t
he   current   fuel  
c

onsumption,
●  
t
he   distance   remaining   to  
b

e travelled or the Stop &
Start   time   counter,
-
t
he trip "1"
 
tab   with:
●  
t
he   distance   travelled,
●  
t
he   average   fuel  
c

onsumption,
●  
t
he   average   speed,
 f

or   the   first   trip.
-
t
he trip "2"
 
tab   with:
●  
t
he   distance   travelled,
●  
t
he   average   fuel  
c

onsumption,
●  
t
he   average   speed,
 f

or   the   second   trip.
F  P ressing   the   button   again   returns   you   to  t
he   normal   display.
16/9 colour screen (eMyWay)
Trip zero reset
F When the trip required is displayed, press
the   button   on   the   end   of   the   wiper   stalk   for  
m

ore   than   two   seconds.
Tr i p s "1" and "2" are independent but their use
is
  identical.
For
  example,   trip   "1" can be used for daily
figures,
  and   trip   "2"
 
for   monthly   figures.
Monitoring

DS3_en_Chap01_controle-de-marche_ed01-2014
A few definitions…
Range
(miles or km)
current fuel consumption
(mpg or l/100 km or km/l)
Stop & Start time
counter
(minutes / seconds or hours / minutes)
This
 
value
 
may
 
vary
 
following
 
a
 
change
 
i

n
 
the
 
style
 
of
 
driving
 
or
 
the
 
relief,
 
r

esulting
 
in
 
a
 
significant
 
change
 
in
 
the
 
c

urrent
 
fuel
 
consumption.
If dashes are displayed continuously
while
 
driving
 
in
 
place
 
of
 
the
 
digits,
 
c

ontact a CITR
oË

N dealer or a
qualified
 w

orkshop.
When
 
the
 
range
 
falls
 
below
 
20
 
miles
 
(30
 
km),
 
d

ashes
 
are
 
displayed.
 
After
 
filling
 
with
 
at
 
least
 
5

 
litres
 
of
 
fuel,
 
the
 
range
 
is
 
recalculated
 
and
 
is
 
d

isplayed
 
when
 
it
 
exceeds
 
60
 
miles
 
(100
 
km).
distance remaining to
destination
(miles or km)
T
his indicates the distance which can still be
travelled
 
with
 
the
 
fuel
 
remaining
 
in
 
the
 
tank
 
in
 
r

elation
 
to
 
the
 
average
 
fuel
 
consumption
 
over
 
t

he
 
last
 
few
 
miles
 
(kilometres)
 
travelled. This
 
is
 
the
 
average
 
fuel
 
consumption
 
during
 
the
 
l

ast
 
few
 
seconds.
This
 
is
 
the   distance   remaining   to   be   travelled  
t

o
 
the
 
final   destination.   It   can   be   entered   by  
t

he user.
If the distance is not entered, dashes are
displayed
  in   place   of   the   digits.
If
 
your
 
vehicle   is   fitted   with   Stop   &   Start,   a   time  
c

ounter
 
calculates   the   time   spent   in   STOP  
m

ode
 
during   a   journey.  
I

t
 
resets
 
to   zero   every   time   the   ignition   is  
s

witched
 
on   with   the   key.
distance travelled
(miles or km)
T
his indicates the distance travelled since the
last
 
trip
 
computer   zero   reset.
Average speed
(mph or km/h)
T
his
 
is
 
the   average   speed   calculated   since   the  
l

ast
 
trip
 
computer   zero   reset   (ignition   on).
Average fuel
consumption
(mpg or l/100 km or km/l)
T
his
 
is
 
the
 
average   fuel   consumption   since   the  
l

ast
 
trip
 
computer   zero   reset.
This
 
function   is   only   displayed   from  
20
 
mph
  (30   km/h).

45
Monitoring
DS3_en_Chap01_controle-de-marche_ed01-2014

DS3_en_Chap02_ecrans-multifonction_ed01-2014
Multifunction screens
Identify your multifunction screen in this section, to adjust or view vehicle settings   and   information,   by   means   of   the   user-friendly   menus.

DS3_en_Chap02_ecrans-multifonction_ed01-2014

DS3_en_Chap02_ecrans-multifonction_ed01-2014
Monochrome screen A
This displays the following information:
-  t ime,
-


date,
-
 
a
mbient   temperature   (this   flashes   if   there   is  
a

  risk   of   ice),
-

s
tatus of the doors and boot,
-
 
c
urrent   audio   source   (radio,   CD...),
-
 
t
rip   computer   (refer   to   the   "Instruments   and  
c

ontrols"
 s
ection).
-
 
i
nformation   or   alert   messages,
-
 
s
ettings   menus   for   the   screen   and   the  
v

ehicle   systems.
displays in the screen
From the control panel of your Audio system, you   can:
F

p
ress the "MENU"
 
button   to   gain   access   to  
t

he main menu ,
F

p
ress the " 5" or " 6" buttons to scroll
through
  the   items   in   the   screen,
F

p
ress the "MO
dE" 
button   to   change  
t

he   permanent   application   (date,   audio  
s

ource...),
F

p
ress the " 7" or " 8"
  buttons   to   change   a  
s

etting   value,
F

p
ress the "OK"
 
button   to   confirm,
or
F

p
ress the "Back" button to abandon the
operation
  in   progress.
controls
F Press the "MENU"  button   to   gain   access  t
o the main menu , then press the "5" or
" 6 "
  buttons   to   scroll   through   the   various  
m

enus:
-


radio - CD,
-
 
v
ehicle   configuration,
-


options,
-
 d

isplay
 se
ttings,
-
 lan

guages,
-
 un

its.
F

P
ress the "OK"
 
button   to   select   the   menu  
r

equired.
Main menu