display CITROEN DS3 CABRIO DAG 2016 Handbook (in English)

121
DS3_en_Chap04_conduite_ed01-2015
F Turn  thumb   wheel   1 to the "LIMIT"
position:   the   speed   limiter   mode   is  
s

elected   but   is   not   switched   on   (PAUSE).
You
  do   not   have   to   switch   the   speed   limiter   on  
i

n   order   to   set   the   speed.
F
 
S
et   the   speed   value   by   pressing   button   2
or 3
  (e.g.:   55   mph   (90   km/h)).
Programming
You can then change the programmed speed using buttons 2 and 3:
-  b y   +   or   -   1   mph   (km/h)   =   short   press,
-
 
b
y   +   or   -   5   mph   (km/h)   =   long   press,
-
 
i
n   steps   of   +   or   -   5   mph   (km/h)   =   maintained   press.
F
 
S
witch   the   speed   limiter   on   by   pressing   button   4.
F
 
S
witch   the   speed   limiter   off   by   pressing   button   4:
  the   display  
c

onfirms   that   it   has   been   switched   off   (PAUSE).
F
 
S
witch   the   speed   limiter   back   on   by   pressing   button   4  
ag
ain.
Exceeding the programmed speed
Pressing the accelerator pedal to exceed the programmed speed will not have any effect unless you press the pedal firmly past the point of resistance.
The
  speed   limiter   is   deactivated   temporarily   and   the   programmed   speed,
 w

hich   is   still   displayed,   flashes.
Returning
  to   the   programmed   speed,   by   means   of   intentional   or   unintentional
 d

eceleration   of   the   vehicle,   automatically   cancels   the   flashing   of   the
 pro

grammed
 s
peed. On a steep descent or in the event of
sharp
  acceleration,   the   speed   limiter  w
ill not be able to prevent the vehicle
from
  exceeding   the   programmed  
s

peed.
To
  avoid   any   risk   of   jamming   of   the  
ped

als:
-
 
e
nsure   that   the   mat   is   secured  
c

o r r e c t l y,
-
 
d
o   not   fit   one   mat   on   top   of   another.
Leaving limiter mode
F Turn  thumb   wheel   1 to the "0"  position:  t
he   speed   limiter   mode   is   deselected.   The  
d

isplay   returns   to   the   distance   recorder.
Operating fault
In the event of a speed limiter fault, the speed is   cleared   resulting   in   flashing   of   the   dashes.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
driving

DS3_en_Chap04_conduite_ed01-2015
Cruise control
System which automatically maintains the speed   of   the   vehicle   at   the   value   programmed  
b

y the driver, without any action on the
accelerator
 ped

al.
The cruise control is switched on
 m

anually:
 it r

equires   a   minimum   vehicle   speed   of   25   mph  
(

40   km/h),   as   well   as   the   engagement   of:
-
 
f
ourth   gear   on   a   manual   gearbox,
-
 
s
econd   gear   on   a   or   automatic   or   electronic  
g

earbox,   in   sequential   mode,
-
position A
  on   an   electronic   gearbox   or  
p

osition d  on   an   automatic   gearbox.
The cruise control is switched off
 m

anually
 o

r   by   pressing   the   brake   or   clutch   pedal   or   on  
t

riggering   of   the   trajectory   control   systems   for  
s

afety   reasons.
It
  is   possible   to   exceed   the   programmed   speed  
t

emporarily   by   pressing   the   accelerator   pedal.
To
  return   to   the   programmed   speed,   simply  
r

elease   the   accelerator   pedal.
Switching
  off   the   ignition   cancels   any  
p

rogrammed   speed   value. The
  controls   of   this   system   are   grouped  
t

ogether   on   stalk   A.
1.
 C

ruise   control   mode   selection   thumb   wheel.
2.
 V

alue   decrease   button.
3.
 V

alue   increase   button.
4.
 C

ruise   control   off/resume   button.Steering mounted controls
The cruise control cannot, in any
circumstances,  replace   the   need   to r

espect   speed   limits,   nor   can   it   replace   the
 n

eed   for   vigilance   on   the   part   of   the   driver.The
  programmed   information   is   grouped  
t

ogether   in   the   instrument   panel   screen.
5.
  C
ruise   control   off/resume   indication.
6.
  C
ruise   control   mode   selection   indication.
7.
  P
rogrammed   speed   value.
displays in the instrument panel

123
DS3_en_Chap04_conduite_ed01-2015
Programming
F Turn  thumb   wheel   1 to the "CRUISE"
position:   the   cruise   control   mode   is  
s

elected   but   is   not   switched   on   (PAUSE).
F
 
S
et   the   programmed   speed   by  
a

ccelerating   to   the   required   speed,   then  
p

ress button 2 or 3   (e.g.:   70   mph  
(110
  km/h)).
You
 
can
 
then
 
change
 
the
 
programmed   speed   using   buttons   2 and 3:
-
 
b

y
 
+
 
or
 
-
 
1
 
mph
 
(km/h)
  =   short   press,
-
 
b

y
 
+
 
or
 
-
 
5
 
mph
 
(km/h)
  =   long   press,
-
 
i

n
 
steps
 
of
 
+
 
or
 
-
 
5
 
mph   (km/h)   =   maintained   press.
F
 
S

witch
 
off
 
the
 
cruise
 
control   by   pressing   button   4:
  the   screen  
c

onfirms
 
that
 
it
 
has
 
been   switched   off   (PAUSE).
F
 
S

witch
 
the
 
cruise
 
control   back   on   by   pressing   button   4  
ag
ain.
Exceeding the programmed speed
Intentional or unintentional exceeding of the programmed speed results in flashing   of   this   speed   in   the   screen.
Return
  to   the   programmed   speed,   by   means   of   intentional   or   unintentional
 d

eceleration   of   the   vehicle,   automatically   cancels   the   flashing   of   the   speed.
Leaving cruise control mode
F Turn  thumb   wheel   1 to the "0"  position:   the   cruise   control   mode   is  d
eselected.   The   display   returns   to   the   distance   recorder.
Operating fault
In the event of a cruise control malfunction, the   speed   is   cleared   resulting   in   flashing   of   the  
d

ashes.   Have   it   checked   by   a   CITROËN   dealer  
o

r   a   qualified   workshop.
When the cruise control is switched on,
be
  careful   if   you   maintain   the   pressure  
o

n   one   of   the   programmed   speed  
c

hanging   buttons:   this   may   result   in   a  
v

ery   rapid   change   in   the   speed   of   your  
v

ehicle.
Do not use the cruise control on
slippery
  roads   or   in   heavy   traffic.
On a steep descent, the cruise control
will not be able to prevent the vehicle
from
  exceeding   the   programmed  
s

peed.
To
  avoid   any   risk   of   jamming   of   the  
ped

als:
-
 
e
nsure   that   the   mat   is   secured  
c

o r r e c t l y,
-
 
n
ever   fit   one   mat   on   top   of   another.
driving

131
DS3_en_Chap05_visibilite_ed01-2015
Model without AUTO lighting
Model with AUTO lighting
Manual controls
The lighting is controlled directly by the driver by   means   of   the   ring   A   and   the   stalk   B.
Automatic
  illumination   of   headlamps.
B.
 S

talk   for   switching   the   headlamp   beam:  
p

ull   the   stalk   to   switch   between   dipped   and  
m

ain   beam   headlamps.
In
  the   lamps   off   and   sidelamps   modes,  
t

he   driver   can   switch   on   the   main   beam  
h

eadlamps   temporarily   ("headlamp   flash")   by  
m

aintaining   a   pull   on   the   stalk.
A.
 M

ain   lighting   mode   selection   ring:   turn   it  
t

o   position   the   symbol   required   facing   the  
ma

rk.Lighting
  off   /   daytime   running   lamps.
Sidelamps
 o

nly.
Dipped headlamps or main beam headlamps.
displays
Lighting of the corresponding indicator lamp on the   instrument   panel   confirms   the   switching   on  
o

f   the   lighting   selected.
The
  instrument   panel   has   permanent   back-
lighting.
  Illumination   of   the   instrument   panel   is  
t

herefore   not   linked   to   the   exterior   lighting.
Visibility

133
DS3_en_Chap05_visibilite_ed01-2015
The temporary illumination of the dipped beam headlamps   after   the   vehicle's   ignition   has   been  
s

witched   off   makes   the   driver's   exit   easier  
w

hen   the   light   is   poor.
Switching on
F With  the   ignition   off,   "flash"   the   headlamps  u
sing   the   lighting   stalk.
F
 
A
  further   "headlamp   flash"   switches   the  
f

unction   off.
Switching off
The manual guide-me-home lighting switches off   automatically   after   a   set   time.
Manual guide-me-home
lighting
The sidelamps and dipped beam headlamps are   switched   on   automatically,   without   any  
a

ction on the part of the driver, when a low level
of
  external   light   is   detected   or   in   certain   cases  
o

f   activation   of   the   windscreen   wipers.
As
  soon   as   the   brightness   returns   to   an  
a

dequate   level   or   after   the   windscreen   wipers  
a

re   switched   off,   these   lamps   are   switched   off  
a

utomatically   and   the   daytime   running   lamps  
c

ome   on.
Automatic illumination of
headlamps
Activation
F Turn   ring   to   the   "AUTO"  position.   The  a
ctivation   of   the   function   is   confirmed   by  
t

he   display   of   a   message.
deactivation
F Turn  ring   to   a   position   other   than   "AUTO".  T
he deactivation of the function is
confirmed
  by   the   display   of   a   message.
Operating fault
In the event of a fault with the
sunshine  sensor,   the   lighting   come  
o

n,   this   warning   lamp   is   displayed  
o

n   the   instrument   panel   and/or   a  
m

essage   appears   in   the   screen,  
a

ccompanied   by   an   audible   signal.
Contact
 
a
 
CITROËN   or   a   qualified   workshop  
w

orkshop.
Visibility

147
DS3_en_Chap06_securite_ed01-2015
The alert is maintained until the system is r einitialised.
The loss of pressure detected does not
always
 
cause
 
visible
 
bulging
 
of
 
the
 
tyre.
 
D

o
 
not
 
satisfy
 
yourself
 
with
 
just
 
a
 
visual
 
c

heck. Before
  reinitialising   the   system,   ensure  
t

hat the pressures of the four tyres are
correct for the use of the vehicle, as
given
  on   the   tyre   pressure   label.
The
  under-inflation   detection   system  
d

oes   not   give   a   warning   if   a   pressure   is  
i

ncorrect   at   the   time   of   reinitialisation.
Under-inflation alert
This is given by fixed illumination of this   warning   lamp,   accompanied   by  
a

n   audible   signal   and   the   display   of   a  
m

essage.
F
 
R

educe   speed   immediately,   avoid  
e

xcessive   steering   movements   and   sudden  
b

raking
F
 
S

top
 
the   vehicle   as   soon   as   it   is   safe   to   do   so.F
 I f   you   have   a   compressor   (such   as   the   one  
i

n   the   temporary   puncture   repair   kit),   check  
t

he   pressures   of   the   four   tyres   when   cold.  
I

f   it   is   not   possible   to   carry   out   this   check  
s

traight   away,   drive   carefully   at   reduced  
s

peed.
or
F

I
n the event of a puncture, use the
temporary
  puncture   repair   kit   or   the   spare  
w

heel   (depending   on   equipment).
Reinitialisation
It is necessary to reinitialise the system every time   one   or   more   tyre   pressure   is   adjusted,   and  
a

fter   changing   one   or   more   wheels.
A
  label   on   the   middle   pillar,   left   hand   side,   gives  
a

  reminder   of   this.
Safety

Reinitialisation of the system is done in the vehicle configuration menu, with the vehicle stationary and the ignition on.
Monochrome screen A
F Press the MEn U button for access to the
main   menu.
F

P
ress the " 5" or " 6" button to select
the Veh conf ig
 

menu,   then   confirm   by  
p

ressing   the   OK
 
button.
F

P
ress the " 5" or " 6" button to select the
" Reinit inflat ",
  menu,   then   confirm   by  
p

ressing   the   OK
 
button.
 A

  message   is   displayed   to   confirm   the  
in

struction.
F
 
C
onfirm   by   pressing   the   OK
 
button.
Monochrome screen C
F Press the MEnU button for access to the
main   menu.
F

P
ress the " 5" or " 6" button to select the
" Personalisation-configuration "
  menu,  
t

hen   confirm   by   pressing   the   OK
 
button.
F

P
ress the " 5" or " 6" button to select the
"
def

ine vehicle parameters "
  menu,   then  
c

onfirm   by   pressing   the   OK
 
button.F
P ress the "
5" or " 6" button to select
the " Tyre pressures "
  menu,   then   the  
"R

einitialisation"
  menu,   then   confirming  
b

y   pressing   the   OK
 
button.
 A

  message   confirms   the   reinitialisation.

149
DS3_en_Chap06_securite_ed01-2015
Touch screen tablet
F Press the MEnU  button.
F Sel ect the "dr iving"
  menu.
F
 
I
n   the   secondary   page,   select   "Under-
inflation initialisation ".
A
  message   is   displayed   to   confirm   the  
r

einitialisation
 i
nstruction.
F

Sel
ect "Ye s" or "
n

o",
  then   confirm.
 A

  message   confirms   the   reinitialisation.The
  new   pressure   settings   registered   are  
c

onsidered to be reference values by the
system.Snow chains
The system does not have to be r einitialised   after   fitting   or   removing  
sn

ow
 c
hains. Before
  doing   anything   to   the   system,  
t

he   pressures   of   the   four   tyres   must   be  c
hecked   and   the   system   reinitialised.
The under-inflation alert is only
dependable
  if   the   system   has   been  
r

einitialised with all four tyres inflated to
the   correct   pressures.
Operating fault
The flashing and then fixed illumination of the u
nder-inflation w arning lam p a ccompanied b

y   illumination   of   the   Service   warning   lamp  
i

ndicates   a   fault   with   the   system.
In
  this   case,   under-inflation   monitoring   of   the  
t

yres   is   no   longer   assured.
Have
  the   system   checked   by   a   CITROËN  
d

ealer   or   a   qualified   workshop.
Safety

Operation
When your vehicle is too close to or
approaches  the   vehicle   ahead   too   quickly   the  
s

ystem   automatically   applies   the   brakes   to  
a

void   a   collision.
The
  collision   can   be   avoided   automatically   if   the
 d

ifference in speed between your vehicle and the
vehicle
  ahead   does   not   exceed   9   mph   (15   km/h).
Above
  this   threshold,   the   system   will   do   what
 i

s possible to avoid or reduce the accident by
lowering
  the   speed   of   impact.
The
  automatic   braking   may   bring   the   vehicle   to  
a

  complete   stop   if   the   situation   requires   it.
In this case, the vehicle is held stationary
temporarily
  (for   about   1.5   seconds)   to   allow  
t

he   driver   to   take   back   control   by   pressing   the  
b

rake
 ped
al.
You are then alerted by the display of a
message.
The
  brake   lamps   on   your   vehicle   come   on   to  
w

arn   other   road   users.
After
  an   impact,   the   system   is  
a

utomatically   put   out   of   service:   it   no  
lon

ger
 ope
rates.
You
  must   go   to   a   CITROËN   dealer   or   a  
q

ualified   workshop   to   have   the   system  
m

ade   operational   again.
During
  automatic   braking,   the   driver  
c

an   always   obtain   a   higher   rate   of  
d

eceleration than that controlled by the
system,
  by   pressing   firmly   on   the   brake  
ped

al.
The
  triggering   of   the   system   may   cause  
t

he   engine   to   stall,   unless   the   driver  
d

epresses   the   clutch   pedal   quickly  
e

nough   during   automatic   braking.
deactivation
The system is deactivated in the vehicle configuration   menu,   accessible   with   the   ignition   on.
Its
  state   is   memorised   when   the   ignition   is
 s

witched off.
When the system is deactivated, a m essage   is   displayed   every   time   the  
i

gnition   is   switched   on,   to   warn   you.

Operating faults
In the event of an impact to the windscreen at the sensor, deactivate
the
  system   and   contact   a   CITROËN  
d

ealer   or   a   qualified   workshop to   have  
y

our   windscreen   replaced.
Never
  try   to   remove,   adjust   or   test  
t

he sensor.
Only
  a   CITROËN   dealer   or   a   qualified
 w

orkshop   is   able   to   work   on   the   system.
When
  towing   a   trailer   or   when   the  
v

ehicle   is   being   towed,   the   system   must  
b

e   deactivated.Do not stick or other wise fix any object on the   windscreen   in   front   of   the   sensor.
Sensor fault
The operation of the laser sensor may suffer inter ference   from   accumulations   of   dirt   or  
m

isting   of   the   windscreen.   In   this   case   you   are  
w

arned   by   the   display   of   a   message.
Use
  the   windscreen   demisting   and   regularly  
c

lean the area of the windscreen in front of the
sensor.
System fault
In the event of a malfunction of the system, you a re   warned   by   an   audible   signal   and   the   display  
o

f   the   message   "Automatic braking system
fault" .
Have
  the   system   checked   by   a   CITROËN  
d

ealer   or   a   qualified   workshop.
In
 
difficult
 
weather
 
conditions
 
(very
 h
eavy
 
rain,
 
snow,
 
fog,
 
hail...),
 
braking
 
d

istances increase, which can reduce
the
 
ability
 
of
 
the
 
system
 
to
 
avoid
 
a
 
c

ollision.
The
 
driver
 
must
 
therefore
 
remain
 
par

ticularly
 v

igilant.
Never
 
leave
 
accumulations
 
of
 
snow
 
or
 
a

ny
 
object
 
projecting
 
above
 
the
 
bonnet
 
o

r
 
in
 
front
 
of
 
the
 
roof:
 
this
 
might
 
fall
 
into
 
t

he field of vision of the sensor and
generate
 
a
 
detection.