Citroen DS3 RHD 2016 1.G Owner's Manual

Page 251 of 380

249
Bonnet
Opening
F Open  the   front   left   door.
F P ull the interior release lever A ,
  located   at  
t

he   bottom   of   the   door   aperture.
F
 
P
ush   the   exterior   safety   catch   B to the left
and
  raise   the   bonnet.
Before
 
doing
 
anything
 
under
 
the
 
b

onnet, switch off the Stop & Start
system
 
to
 
avoid
 
any
 
risk
 
of
 
injury
 
r

esulting
 
from
 
an
 
automatic
 
change
 
to
 
S

TART
 
mode.
The location of the interior release lever
prevents  opening   of   the   bonnet   while  
t

he   front   left   door   is   closed.F

U
nclip the bonnet stay C   from   its   housing,  
h

olding   it   by   its   foam   protection.
F
 
F
ix   the   stay   in   the   notch   to   hold   the   bonnet  
ope

n.
Closing
F Take  the   stay   out   of   the   support   notch.
F  C lip   the   stay   in   its   housing.
F
 
L
ower   the   bonnet   and   release   it   at   the   end  
o

f   its   travel.
F
 
P
ull   on   the   bonnet   to   check   that   it   is   fully  
l

atched.When
  the   engine   is   hot,   handle   the  
e

xterior   safety   catch   and   the   stay   with  
c

are.
Because of the presence of electrical
equipment
 
under
 
the
 
bonnet,
 
it
 
is
 
r

ecommended
 
that
 
exposure
 
to
 
water
 
(

rain,
 
washing, ...)
 
be
 
limited.
The cooling fan may star t after
switching off the engine: take care
with articles and clothing that might
be caught by the fan blades.
Checks

Page 252 of 380

Petrol engines
1. Screenwash  fluid   reservoir.
2. C oolant   header   tank.
3.
 A

ir   filter.
4.
 B

rake   fluid   reservoir.
5.
 B

attery.
6.
 F

usebox.
7.
 E

ngine   oil   dipstick.
8.
 E

ngine   oil   filler   cap.

Page 253 of 380

251
Diesel engines
1. Screenwash  fluid   reservoir.
2. C oolant   header   tank.
3.
 A

ir   filter.
4.
 B

rake   fluid   reservoir.
5.
 B

attery.
6.
 F

usebox.
7.
 E

ngine   oil   dipstick.
8.
 E

ngine   oil   filler   cap.
9.
 P

riming   pump   (on   fuel   filter).
Checks

Page 254 of 380

Checking levels
Check all of these levels regularly, in line with the manufacturer's service schedule. Top them up if necessary, unless other wise indicated.
I f   a   level   drops   significantly,   have   the   corresponding   system   checked   by   a   CITROËN   dealer   or   a   qualified   workshop.
Engine oil level
It is normal to top up the oil level between two   services   (or   oil   changes).   CITROËN  
r

ecommends   that   you   check   the   level,   and   top  
u

p   if   necessary,   every   3   000   miles   (5   000   kms).
The
  check   is   carried   out   either   when  
t

he   ignition   is   switched   on   using   the  
o

il   level   indicator   in   the   instrument  
p

anel   for   vehicles   so   equipped,   or  
u

sing   the   dipstick.
To   ensure   that   the   reading   is   correct,  
y

our   vehicle   must   be   parked   on   a   level  
s

ur face   with   the   engine   having   been   off  
f

or   more   than   30   minutes.
Take   care   when   working   under   the  
b

onnet,   as   certain   areas   of   the   engine  
m

ay   be   extremely   hot   (risk   of   burns)  
a

nd   the   cooling   fan   could   start   at   any  
t

ime   (even   with   the   ignition   off).
Checking using the dipstick
A = MA X
B   =   MIN If
  you   find   that   the   level   is   above   the   A   mark   or  
belo

w the B   mark,   do not star t the engine
.
-  
I
f   the   level   is   above   the   MAX
 
mark   (risk  
o

f   damage   to   the   engine),   contact   a  
C

ITROËN   dealer   or   a   qualified   workshop.
-  
I
f   the   level   is   below   the   MI n
  mark,   you  
m

ust   top   up   the   engine   oil.
F
 
L

ocate
 
the   dipstick   in   the   engine  
c

ompartment   of   your   vehicle.
For
 
more
 
information   on   the   petrol   or   Diesel  
e

ngine,
 
refer
  to   the   corresponding   section.
F
 
T

ake
 
the
  dipstick   by   its   coloured   grip   and  
r

emove
 
it   completely.
F
 
W

ipe
 
the
  end   of   the   dipstick   using   a   clean  
n

on-fluffy   cloth.
F
 
R

efit
 
the
  dipstick   and   push   fully   down,   then  
p

ull
 
it
 
out   again   to   make   the   visual   check:  
t

he
 
correct   level   is   between   the   marks   A
and
 
B
.
Oil grade
Before topping-up the oil or changing the oil, c
heck   that   the   oil   is   the   correct   grade   for   your  
e

ngine   and   conforms   to   the   manufacturer's  
r

ecommendations.

Page 255 of 380

253
Brake fluid level
Changing the fluid
Refer to the manufacturer's service schedule for   details   of   the   interval   for   this   operation.
Fluid specification
The brake fluid must conform to the manufacturer's r ecommendations.
The
  brake   fluid   level   should   be   close  
t

o   the   "MA X"   mark.   If   it   is   not,   check  
t

he   brake   pad   wear.
After
 
topping-up
 
the
 
oil,
 
the
 
check
 
when
 
s

witching
 
on
 
the
 
ignition
 
with
 
the
 
oil
 
level
 
i

ndicator
 
in
 
the
 
instrument
 
panel
 
is
 
not
 
valid
 
d

uring
 
the
 
30
 
minutes
 
after
 
topping
 
up.
Topping-up the engine oil level
F Locate   the   oil   filler   cap   in   the   engine  c
ompartment   of   your   vehicle.
For
  more   information   on   the   petrol   or   Diesel  
e

ngine,   refer   to   the   corresponding   section.
F

U
nscrew the oil filler cap to reveal the filler
aperture.
F
 
A
dd   oil   in   small   quantities,   avoiding   any  
s

pills   on   engine   components   (risk   of   fire).
F
 
W
ait   a   few   minutes   before   checking   the  
l

evel   again   using   the   dipstick.
F
 
A
dd   more   oil   if   necessary.
F
 
A
fter   checking   the   level,   carefully   refit   the  
o

il   filler   cap   and   the   dipstick   in   its   tube.
Engine oil change
Refer to the manufacturer's service schedule for   details   of   the   interval   for   this   operation.
In
  order   to   maintain   the   reliability   of   the   engine  
a

nd   emission   control   system,   never   use  
a

dditives   in   the   engine   oil.
Checks

Page 256 of 380

Fluid specification
The coolant must conform to the manufacturer's r ecommendations.
Coolant level
The coolant level should be close to   the   "MA X"   mark   but   should   never  
e

xceed   it.
In
 
addition,   as   the   cooling   system   is  
p

ressurised,   wait   at   least   one   hour   after  
s

witching
 
off   the   engine   before   carrying   out   any  
wo

rk.
To
 
avoid
 
any   risk   of   scalding,   unscrew   the   cap  
b

y
 
two
 
turns   to   allow   the   pressure   to   drop.  
W

hen
 
the
  pressure   has   dropped,   remove   the  
c

ap
 
and
 
top   up   the   level.
When
 
the
  engine   is   warm,   the   temperature   of  
t

he
 
coolant   is   regulated   by   the   fan.
The cooling fan may star t after
switching off the engine: take care
with articles and clothing that might
be caught by the fan blades.
Screenwash fluid level
Fluid specification
For optimum cleaning and to avoid freezing, t his   fluid   must   not   be   topped   up   or   replaced  
w

ith   plain   water.
In
 
w
intry  
c
onditions,  
i
t  
i
s  
r
ecommended  
t
hat  
y
ou  
u

se   an   ethyl   alcohol   or   methanol   based   fluid.
Top
  up   the   level   when   necessary.

Page 257 of 380

255
diesel additive level (diesel
engine with particle filter)
To p p i n g u p
This additive must be topped up by a CITROËN d
ealer   or   a   qualified   workshop   without   delay.
Used products
Avoid prolonged contact of used oil or fluids   with   the   skin.
Most
  of   these   fluids   are   harmful   to  
h

ealth   or   indeed   very   corrosive.
Do
  not   discard   used   oil   or   fluids   into  
s

ewers   or   onto   the   ground.
Take
  used   oil   to   a   CITROËN   dealer   or  
a

  qualified   workshop   (France)   or   to   an  
a

uthorised   waste   disposal   site.
The
 
additive
 
reservoir
 
low
 
level
 
is
 
i

ndicated
 
by
 
fixed
 
illumination
 
of
 
t

his
 
warning
 
lamp,
 
accompanied
 
by
 
a

n
 
audible
 
warning
 
and
 
a
 
message
 
i

n
 
the
 
multifunction
 
screen.
Checks

Page 258 of 380

Checks
12 V batteryAir filter and passenger compartment filter
Oil filterParticle filter (
di
esel)
Unless other wise indicated, check these components in accordance with the manufacturer's service schedule and according to your engine.
O ther wise,   have   them   checked   by   a   CITROËN   dealer   or   a   qualified   workshop.
The battery does not require any maintenance.However, check regularly that the terminals   are   correctly   tightened   and  
t

hat   the   connections   are   clean. Refer
  to   the   manufacturer's  s
ervice   schedule   for   details   of   the  r
eplacement   intervals   for   these  
c

omponents.
Replace
  the   oil   filter   each   time   the  
e

ngine   oil   is   changed.
Refer
  to   the   manufacturer's  
s

ervice   schedule   for   details   of  
t

he   replacement   interval   for   this  
c

omponent.
Versions
  equipped   with   Stop   &   Start
 a

re   fitted   with   a   12   V   lead-acid  
b

attery   of   specific   technology   and  
s

pecification.
Its
  replacement   should   be   carried  
o

ut   only   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop. The start of saturation of the
particle
  filter   is   indicated   by   the  
O

n a new vehicle, the first particle
filter
  regeneration   operations   may   be  
a

ccompanied   by   a   "burning"   smell,  
w

hich   is   per fectly   normal.
Following
  prolonged   operation   of   the  
v

ehicle   at   very   low   speed   or   at   idle,  
y

ou   may,   in   exceptional   circumstances,  
n

otice   the   emission   of   water   vapour   at  
t

he   exhaust   on   acceleration.   This   does  
n

ot affect the behaviour of the vehicle
or
  the   environment.
When
 
carrying   out   any   operation   on   the   12   V  
b

attery,
 
refer   to   the   corresponding   section   for  
d

etails
 
of
 
the   precautions   to   be   taken   before  
s

tarting
 
work. Depending
  on   the   environment   (e.g.   dusty  
a

tmosphere)   and   the   use   of   the   vehicle   (e.g.  
c

ity   driving),   replace them twice as often if
necessary .
A
  clogged   passenger   compartment   filter   may  
h

ave   an   adverse   effect   on   the   per formance  
o

f   the   air   conditioning   system   and   generate  
u

ndesirable
 o
dours.temporary
  illumination   of   this   warning   lamp  
a

ccompanied   by   a   message   in   the   multifunction  
sc

reen.
As
  soon   as   the   traffic   conditions   permit,  
r

egenerate   the   filter   by   driving   at   a   speed   of   at  
l

east   40   mph   (60   km/h)   until   the   warning   lamp  
g

oes   off.
If
  the   warning   lamp   stays   on,   this   indicates   a  
l

ow   additive   level.
For
  more   information   on   checking   levels,   refer  
t

o   the   corresponding   section.

Page 259 of 380

257
Manual gearbox
Automatic gearboxBrake pads
Brake wear depends on the style o
f   driving,   particularly   in   the   case o

f   vehicles   used   in   town,   over   short
 d

istances.   It   may   be   necessary   to   have
 t

he   condition   of   the   brakes   checked,
 e

ven   between   vehicle   services.
The
 
gearbox
 
does
 
not
 
require
 
any
 m
aintenance
 
(no
 
oil
 
change).
Refer
 
to
 
the
 
manufacturer's
 
service
 
s

chedule
 
for
 
the
 
checking
 
interval
 
for
 
t

his
 c

omponent.
Only
  use   products   recommended   by  
C

ITROËN   or   products   of   equivalent  
q

uality
 an
d
 sp
ecification.
In
  order   to   optimise   the   operation   of  
u

nits   as   important   as   those   in   the  
b

raking   system,   CITROËN   selects   and  
o

ffers   very   specific   products.
The
 
gearbox
 
does
 
not
 
require
 
any
 
m

aintenance
 
(no
 
oil
 
change).
Refer
 
to
 
the
 
manufacturer's
 
service
 
s

chedule
 
for
 
details
 
of
 
the
 
level
 
c

hecking
 
interval
 
for
 
this
 
component.
Electronic gearbox
The gearbox does not require any m aintenance   (no   oil   change).
Refer
  to   the   manufacturer's   service  
s

chedule   for   details   of   the   checking  
i

nterval   for   this   component. For
  information   on   checking   brake  
d

isc   wear,   contact   a   CITROËN   dealer  
o

r   a   qualified   workshop.
Brake disc wearParking brake
If excessive travel or a loss of e
ffectiveness   of   this   system   is  
n

oticed,   the   parking   brake   must   be  
c

hecked,   even   between   two   services.
Unless
 
there
 
is
 
a
 
leak
 
in
 
the
 
circuit,
 
a
 
drop
 
in
 
t

he
 
brake
 
fluid
 
level
 
indicates
 
that
 
the
 
brake
 
p

ads
 
are
 
worn. Checking
 
this   system   must   be   done   by   a  
C

ITROËN   dealer   or   a   qualified   workshop.
After
 
washing
 
the
 
vehicle,
 
dampness,
 
o

r
 
in
 
wintry
 
conditions,
 
ice
 
can
 
form
 
o

n
 
the
 
brake
 
discs
 
and
 
pads:
 
braking
 
e

fficiency
 
may
 
be
 
reduced.
 
Make
 
light
 
b

rake
 
applications
 
to
 
dry
 
and
 
defrost
 
t

he
 
brakes.
Checks

Page 260 of 380

Technical data
01

Page:   < prev 1-10 ... 211-220 221-230 231-240 241-250 251-260 261-270 271-280 281-290 291-300 ... 380 next >