DACIA SOLENZA 2004 Repair Manual

IGNITION AND INJECTION
17
17 - 87
ALP 4 INTEMP ERATE ACCELERATION OR DECELERATION
(engine unstable running)
RECOMMEND AT IONS Do not consult this diagnostic but before a complete checking by
means of the CLIP tester
Ch eck if air filter is not deformed.
Ch eck if there is petrol in the fuel tank (fuel indicator failure)
Ch eck if the vehic le is supplied with adequate fuel
Ch eck tha t supply cir cuit hoses are not broken (espe cially further to a dismounting)
Ch eck the condition of the fuel filter
Ch eck the condition of the fuel tank
Ch eck that fuel tank aeration is taking place.
Disconnect the connection hose between the canister purging valve and the intake manifold.
Cl amp the connection hose in order to stop the air passing.
If there are no more disturbances, the cause is the canister purging valve.
Ch eck the spark plugs and ignition coil condition
Ch eck tha t these eleme nts are specific to that vehicle.
Ch eck that the exhaust route is not clogged and the catalyst is not clogged.
Ch eck the se aling of the exhaust manifold.
Ch eck, by means of the oil dipstick, that oil level is not too high.
Ch eck for lack of sealing at servo-brake (noise).
Ch eck the intake manifold condition
Ch eck if the valve body is not clogged
Ch eck the engine compressions.
Ch eck tha t brake calipers, drums and bearings are not gripped.
Ch eck that tires are inflated
Ch eck the engine flywheel condition
Ch eck tha t cooling system is properly operating
AFTER Perform a checking by means of the CLI P tester.
REPARATION
Fa ilure locating algorithm
vnx.su

IGNITION AND INJECTION
17
17 - 88
ALP 5ENGINE OPERATION BREAKDOWN
Failure locating algorithm
AFTERPerform a road test then a checking by means of CLIP tester.
REPARATIONFix possible detected failures.
RECOMMEND AT IONSDo not use these information but after performing complete
checking by means of CLIP tester.
Check the followings :
- fuel conformity;
- lack of air circuit clogging, supply circuit and fuel circuit;
- lack of important air leak;
- injection pump setting on;
- injectors.
vnx.su

IGNITION AND INJECTION
17
17 - 89
ALP 6ENGINE STOPPING
Failure locating algorithm
AFTERPerform a road test then a checking by means of CLIP tester.
REPARATIONFix possible detected failures.
RECOMMEND AT IONSDo not use these informations but after performing complete
checking by means of CLIP tester.
Check the followings :
- lack of air circuit clogging, supply circuit and fuel circuit.
- lack of fuel leak
- injectors
- injecton pump
- engine
- supply +12V after setting on the contact at pin 81 of the injection computer.
vnx.su

IGNITION AND INJECTION
17
17 - 90
ALP 7ENGINE N OISE
Failure locating algorithm
AFTERPerform a road test then a checking by means of CLIP tester.
REPARATIONFix possible detecetd failures.
RECOMMEND AT IONSDo not use these information but after performing complete
checking by means of CLIP tester.
Check the followings:
- lack of a ir leak;
- pre-heating spark plugs;
- injection pump setting on;
- injectors;
- injection pump;
- engine;
- combustion pre-chambers.
vnx.su

IGNITION AND INJECTION
17
17 - 91
ALP 8SM OKE
Failure locating algorithm
AFTERPerform a road test then a checking by means of CLIP tester.
REPARATIONFix possible detected failures.
RECOMMEND AT IONSDo not use these informations but after performing complete
checking by means of CLIP tester.
Check the followings:
- injection pump setting on;
- injectors;
- injection pump;
- lack of a ir leak;
- pre-heating spark plugs;
- engine.
vnx.su

IGNITION AND INJECTION
17
17 - 92
ALP 9LACK OF PE RF O RM ANCES
Failure locating algorithm
AFTERPerform a road test then a checking by means of CLIP tester.
REPARATIONFix possible detected failures.
RECOMMEND AT IONSDo not use these informations but after performing complete
checking by means of CLIP tester.
Check the followings :
- fuel conformity;
- lack of air circuit clogging, supply circuit and fuel circuit;
- lack of fuel leak and air leak;
- injection pump setting on;
- engine compression;
- injectors;
- injection pump;
- pre-heating spark plugs.
vnx.su

IGNITION AND INJECTION
17
17 - 93
ALP 10FUEL CONSUMPTION
Failure locating algorithm
AFTERPerform a road test then a checking by means of CLIP tester.
REPARATIONFix possible detected failures.
RECOMMEND AT IONSDo not use these informations but after performing complete
checking by means of CLIP tester.
Check the followings :
- air filter;
- diesel filter;
- vahicle exploitation conditions;
- injectors.
vnx.su

19
19 - 1
COOLING - EXHAUST - TANK
COOLING FLUID QUANTITY AND QUALITY
Chara cteristics
ENGINE QUANTITY* (liter s)QUALITY CHARACTERISTICS
E7J 6 Antifreeze type D Protection until –40°C
GLACEOL RX
⟨ Mixture : 50% concentrate d antifreeze + 50% distilled water.
THERMOSTAT
ENGINE TYPE OPENING START (°C) OPENING END (°C) STROKE (mm)
F8Q89 1017.5
vnx.su

19
19 - 2
COOLING - EXHAUST - TANK
The heating radiator has no valve.
The fluid circ ulation is permanently done in the heating radiator, this leading to t he engine
cooling.
FILLING
Open the purging screw located on the water pipe between engine and climate control radiator.
Fill up the circuit by the expansion vessel hole
Tighten the purging screws in the moment when the fluid is flowing in a continuos jet.
Start the engine, maintaining it at 2500 rot/min.
Adjust the fluid level in the expansion vessel, during about 4 minutes.
Close the cap of the expansion vessel.
PURGING
Let the engine run for 10 minutes at 2500 rot/min, until engine fan starting (necessary
period for automatic gas purge).
Check if the fluid level in the expansion vessel is nearby the mark “Max”.
Do not open the purging screws with the engine running.
Ret ighten the expansion vessel cap with the warm e ngine.
Filling - Purging
vnx.su

19
19 - 3
COOLING - EXHAUST - TANKChecking
SPECIAL TOOLS
MS 5 54-01 Adapter fo r M.S. 554-07
MS 5 54-06 Adapter fo r M.S. 554-07
MS 5 54-07 Kit for checking the coo ling system sealing
1. CIRCUIT S EALIN G CHECKING
Mount the adapter M.S 554 –01 instead of
the expansion vessel valve.
Connect a t the adapter, the M.S. 554-07
device. Wa rm the engine, then stop it.
P ump, in order to create pressure in the cir-
cuit. Stop pumping at a value lower with 0.1 bar
then the valve calibrating value ( 1.2 bar)
The pressure must not drop, if not, check for
leak and fix it.
Progressively unscrew the device connection
for cooling circuit decompressing , then unscrew
the device, and mount back the expansion vessel
valve.
2. CHECKING ALVE CALIBRATION
M ount t he expansion vessel va lve on
adapter M.S. 554-06 and connect it to the
MS 557-07 device.
P ump to increase the pressure, this must
be stabilized at the valve calibration value 1.2
w ith a checking tolerance of ± 0.1 bar.
The calibra tion value of t he expansion
vessel valve is : 1.2 bar.
vnx.su