DAEWOO LACETTI 2004 Service Service Manual

GENERAL ENGINE INFORMATION 1A – 9
DAEWOO V–121 BL4
Piston Noises
StepActionValue(s)YesNo
1Are any of the following noises heard: a sharp double
knock when the engine is idling, a light ticking with
no load on the engine, or a ”slapping” noise when the
engine is cold?–Go to Step 2System OK
2Inspect the piston pin and the bushing.
Is the piston pin or the bushing worn or loose?–Go to Pistons
and Rods Re-
placement Pro-
cedureGo to Step 3
3Inspect the piston.
Is the piston broken or cracked?–Go to Pistons
and Rods Re-
placement Pro-
cedureGo to Step 4
4Inspect the connecting rods.
Is there a misaligned connecting rod?–Go to Pistons
and Rods Re-
placement Pro-
cedureGo to Step 5
5Inspect the piston position.
Is the piston 180° out of position?–Go to Pistons
and Rods Re-
placement Pro-
cedureSystem OK

1A – 10IGENERAL ENGINE INFORMATION
DAEWOO V–121 BL4
Valve Mechanism or Valve Train Noises
StepActionValue(s)YesNo
1Is a light tapping sound heard from the engine?–Go to Step 2System OK
2Inspect the valve springs.
Are the springs weak or broken?–Go to Cylinder
Head and
Valve Train
Components
Replacement
ProcedureGo to Step 3
3Inspect the valves.
Are the valves sticking or warped?–Go to Cylinder
Head and
Valve Train
Components
Replacement
ProcedureGo to Step 4
4Inspect the valve lifters.
Are the valve lifters dirty, stuck or worn?–Go to Cylinder
Head and
Valve Train
Components
Replacement
ProcedureGo to Step 5
5Inspect the camshaft lobes.
Are the camshaft lobes damaged or improperly ma-
chined?–Go to Cam-
shaft Replace-
ment Proce-
dureGo to Step 6
6Check the oil supply to the valve train.
Is the oil supply insufficient or poor?–Go to Cylinder
Head and
Valve Train
Components
Replacement
ProcedureGo to Step 7
7Inspect the valve guides.
Are the valve guides worn?–Go to Cylinder
Head and
Valve Train
Components
Replacement
ProcedureGo to Step 8
8Inspect the valve spring seat.
Is the valve spring seat incorrect?–Go to Cylinder
Head and
Valve Train
Components
Replacement
ProcedureSystem OK

GENERAL ENGINE INFORMATION 1A – 11
DAEWOO V–121 BL4
GENERAL INFORMATION
CLEANLINESS AND CARE
An automobile engine is a combination of many machined,
honed, polished and lapped surfaces with tolerances that
are measured in the ten–thousandths of an inch. When
any internal engine parts are serviced, care and cleanli-
ness are important. A liberal coating of engine oil should
be applied to friction areas during assembly, to protect and
lubricate the surfaces on initial operation. Proper cleaning
and protection of machined surfaces and friction areas is
part of the repair procedure. This is considered standard
shop practice even if not specifically stated.
Whenever valve train components are removed for ser-
vice, they should be kept in order. They should be installed
in the same locations, and with the same mating surfaces,
as when they were removed.Battery cables should be disconnected before any major
work is performed on the engine. Failure to disconnect
cables may result in damage to wire harness or other elec-
trical parts.ON–ENGINE SERVICE
CAUTION : Disconnect the negative battery cable be-
fore removing or installing any electrical unit, or
when a tool or equipment could easily come in con-
tact with exposed electrical terminals. Disconnecting
this cable will help prevent personal injury and dam-
age to the vehicle. The ignition must also be in LOCK
unless otherwise noted.
Notice : Any time the air cleaner is removed, the intake
opening should be covered. This will protect against acci-
dental entrance of foreign material, which could follow the
intake passage into the cylinder and cause extensive
damage when the engine is started.

SECTION : 1C1
1.4L/1.6L DOHC ENGINE MECHANICAL
CAUTION : Disconnect the negative battery cable before removing or installing any electrical unit or when a tool
or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable will help
prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise noted.
TABLE OF CONTENTS
SPECIFICATIONS1C1–2 . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Specifications 1C1–2. . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifcations 1C1–5. . . . . . . . . .
SPECIAL TOOLS1C1–7 . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Tools Table 1C1–7. . . . . . . . . . . . . . . . . . . . . . .
COMPONENT LOCATOR1C1–9 . . . . . . . . . . . . . . . . . . .
Cylinder Head 1C1–9. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Block 1C1–10. . . . . . . . . . . . . . . . . . . . . . . . . . .
Intake & Exhaust Manifold 1C1–12. . . . . . . . . . . . . . . .
Timing Belt 1C1–13. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Mounting 1C1–14. . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE AND REPAIR1C1–15 . . . . . . . . . . . . .
ON–VEHICLE SERVICE 1C1–15. . . . . . . . . . . . . . . . . . .
Engine Cover 1C1–15. . . . . . . . . . . . . . . . . . . . . . . . . . .
Camshaft Cover 1C1–15. . . . . . . . . . . . . . . . . . . . . . . . .
Intake Manifold 1C1–16. . . . . . . . . . . . . . . . . . . . . . . . . .
Exhaust Manifold 1C1–20. . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Gasket 1C1–21. . . . . . . . . . . . . . . .
Camshaft 1C1–29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timing Belt Check and Adjust 1C1–30. . . . . . . . . . . . .
Timing Belt 1C1–34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oil Pan 1C1–38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pump 1C1–40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Mount 1C1–43. . . . . . . . . . . . . . . . . . . . . . . . . . .
Camshaft Gears 1C1–45. . . . . . . . . . . . . . . . . . . . . . . . .
Rear Timing Belt Cover 1C1–46. . . . . . . . . . . . . . . . . . .
Engine 1C1–48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pistons and Rods 1C1–53. . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR 1C1–58. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Valve Train Components 1C1–58.
Crankshaft 1C1–65. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Crankshaft Bearing and Connecting Rod
Beadings – Gauging Plastics 1C1–74. . . . . . . . . . . .
GENERAL DESCRIPTION AND SYSTEM
OPERATION1C1–77 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Gasket 1C1–77. . . . . . . . . . . . . . . .
Crankshaft 1C1–77. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timing Belt 1C1–77. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pump 1C1–77. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pan 1C1–77. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exhaust Manifold 1C1–77. . . . . . . . . . . . . . . . . . . . . . . .
Intake Manifold 1C1–77. . . . . . . . . . . . . . . . . . . . . . . . . .
Camshaft 1C1–77. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1C1 – 2I1.4L/1.6L DOHC ENGINE MECHANICAL
DAEWOO V–121 BL4
SPECIFICATIONS
ENGINE SPECIFICATIONS
ApplicationDescription (Manual and Automatic)
1.4L DOHC1.6L DOHC
General Data:
Engine TypeF14DF16D
Displacement1399 cm31598 cm3 (97.51 in3)
Bore Stroke77.9 x 73.4 mm (3.01 in. x 2.89 in.)79.0 x 81.5 mm (3.1 in. X 3.21 in.)
Compression Ratio9.5 ± 0.2:19.5 ± 0.2:1
Firing Oder1–3–4–21–3–4–2
Cylinder Bore:
Diameter77.9 mm (3.07 in.)79 mm (3.1 in.)
Out of Round (Maximum)0.0065 mm (0.00025 in.)0.0065 mm (0.00025 in.)
Taper (Maximum)0.07 x 30°0.0065 mm (0.00025 in.)
Pistion:
Diameter77.87 mm (3.07 in.)78.970 mm (3.1090 in.)
Clearance to Bore0.030 mm (0.0012 in.)0.030 mm (0.0012 in.)
Piston Rings:
Ring, End Gap:
Top Compression
2nd Compression0.15–0.30 mm
(0.0059–0.0118 in.)
0.3–0.5 mm (0.0118–0.0197 in.)0.2–0.3 mm (0.008–0.012 in.)
0.5–0.6 mm (0.02–0.024 in.)
Groove Clearance:
Top Compression
2nd Compression0.05–0.09 mm
(0.00197–0.00354 in.)
0.06–0.1 mm
(0.00236–0.00393 in.)0.016 mm (0.0006 in.)
0.066 mm (0.0026 in.)
Piston Pin:
Diameter18.00 mm (0.708 in.)18.00 mm (0.708 in.)
Pin Off–Set0.5 ± 0.1 mm
(0.0197 ± 0.00787 in.)0.7–0.9 mm (0.028–0.036 in.)
Camshaft:
Lift Intake7.2 mm (0.283 in.)8.5 mm (0.335 in.)
Lift Exhaust7.2 mm (0.283 in.)8.5 mm (0.335 in.)
End Play0.1–0.25 mm (0.00394–0.00787 in.)0.10–0.25 mm (0.004–0.0089 in.)
Journal OD:
No. 1
No. 2
No. 3
No. 4
No. 529.94 mm (1.179 in.)
26.94 mm (1.061 in.)
26.94 mm (1.061 in.)
26.94 mm (1.061 in.)
26.94 mm (1.061 in.)30 mm (1.18 in.)
27 mm (1.06 in.)
27 mm (1.06 in.)
27 mm (1.06 in.)
27 mm (1.06 in.)

1.4L/1.6L DOHC ENGINE MECHANICAL 1C1 – 3
DAEWOO V–121 BL4
ApplicationDescription (Manual and Automatic)
1.4L DOHC1.6L DOHC
Crankshaft:
Main Journal:
Diameter (All)
Taper (Maximum)
Out of Round (Maximum)55 mm (2.71 in.)
0.005 mm (0.0001 in.)
0.004 mm (0.0001 in.)54.982–54.994 mm
(2.164–2.165 in.)
0.005 mm (0.0001 in.)
0.004 mm (0.0001 in.)
Main Bearing Clearance (All)0.026–0.042 mm (0.001–0.002 in.)0.026–0.042 mm (0.001–0.002 in.)
Crankshaft End Play0.1 mm (0.003 in.)0.05–0.28 mm (0.002–0.011 in.)
Connecting Rod Journal:
Diameter (All)43 mm (1.69 in.)
42.971–42.987 mm
(1.691–1.692 in.)
Taper (Maximum)0.005 mm (0.0001 in.)0.005 mm (0.0001 in.)
Out of Round (Maximum)0.004 mm (0.0001 in.)0.004 mm (0.0001 in.)
Rod Bearing Clearance (All)0.019–0.070 mm
(0.0007–0.0028 in.)0.019–0.071 mm
(0.0007–0.0028 in.)
Rod Side Clearance0.070–0.242 mm
(0.0027–0.009 in.)0.070–0.242 mm
(0.0027–0.009 in.)
Valve System:
Valve Lash CompensatorsHydraulicHydraulic
Face Angle (All)45°~45.25°90°~90.5°
Seat Angle (All)44.5°~45°89°~90°
Seat Runout (Maximum, All)0.05 mm (0.002 in.)0.05 mm (0.002 in.)
Face Runout (Maximum, All)0.03 mm (0.0012 in.)0.03 mm (0.0012 in.)
Seat Width:
Intake
Exhaust1.17–1.57 mm (0.046–0.062 in.)
1.4–1.8 mm (0.055–0.071 in.)1.17–1.57 mm (0.046–0.062 in.)
1.4–1.8 mm (0.055–0.071 in.)
Valve Guide Inside Diameter (All)6.00–6.02 mm (0.236–0.237 in.)6.00–6.02 mm (0.236–0.237 in.)
Valve Stem Diameter (All)6 mm (0.236 in.)6 mm (0.236 in.)
Valve Diameter (All):
Intake
Exhaust28.57 mm (1.125 in.)
27.24 mm (1.074 in.)28.6 mm (1.126 in.)
27.2 mm (1.072 in.)
Valve Spring Loads:
Valve Open
Valve Closed580 ± 29N (426 ± 21 lbs)
260 ± 13N (191 ± 9.6 lbs)580–26N (428–19 lbs)
@23.0 mm(0.90 in.)
260”13N(192” 9 lbs) @
32.0mm(1.25 in.)
Valve Spring Free Length41.2 mm (1.622 in.)41.2 mm (1.622 in.)
Oil Pump:
Gap Between Oil Pump Body and Out
Rotor0.400~0.484 mm
(0.0157~0.019 in.)0.400~0.484 mm (0.0157~0.019 in.)
Out Rotor Side Clearance0.045~0.100 mm
(0.0018~0.0039 in.)0.045~0.100 mm (0.02~0.004 in.)

1C1 – 4I1.4L/1.6L DOHC ENGINE MECHANICAL
DAEWOO V–121 BL4
ApplicationDescription (Manual and Automatic)
1.4L DOHC1.6L DOHC
Inner Rotor Side Clearance0.035~0.085 mm (0.001~0.003 in.)0.035~0.085 mm (0.001~0.003 in.)
Relief Valve Spring Free Length81 mm (3.2 in.)81 mm (3.2 in.)
Sealants and Adhesives:
Rear Main Bearing CapGE p/n RTV 159
Camshaft Carrier to Cylinder HeadHN 1581 (Loctite® 515)
Oil Pan BoltsHN 1256 (Loctite® 242)
Oil Pump BoltsHN 1256 (Loctite® 242)
Oil Pan Pickup Tube BoltsHN 1256 (Loctite® 242)
Oil Gallery PlugHN 1256 (Loctite® 242)
Coolant Jacket Caps and Plugs
(Freeze Plugs)HN 1756 (Loctite® 176)
Exhaust Manifold Studs/NutsAnti–seize Compound (HMC Spec HN1325)

1.4L/1.6L DOHC ENGINE MECHANICAL 1C1 – 5
DAEWOO V–121 BL4
FASTENER TIGHTENING SPECIFCATIONS
ApplicationNSmLb–FtLb–In
Air Cleaner Housing Bolts10–89
Camshaft Cap Bolts1612–
Camshaft Cover Nuts10–89
Connecting Rod Bearing Cap Bolts25
+ 30° + 15°18
+ 30° + 15°–
Coolant Temperature Sensor2015–
Crankshaft Bearing Cap Bolts50
+ 45° + 15°37
+ 45°+ 15°–
Crankshaft Cover Nuts5~8–44~71
Crankshaft Pulley Bolt95 NSm
+ 30° + 15°––
Cylinder Head Bolts (Cylinder Head Mounting Bolts)25 + 70°
+ 70° + 50°18 + 70°
+ 70° + 50°–
Direct Ignition System Coil Mounting Bolts10–89
Direct Ignition System Coil Mounting Bracket Bolts10–89
Engine Mount Attaching Bolts3022–
Engine Mount Bracket Attaching Bolts/Nuts5037–
Exhaust Camshaft Gear Bolt67.549–
Exhaust Flex Pipe–to–Catalytic Converter or Connecting Pipe
Retaining Nut3526–
Exhaust Flex Pipe–to–Exhaust Manifold Retaining Nuts3526–
Exhaust Gas Recirculation Valve Adapter Bolts2518–
Exhaust Manifold Heat Shield Bolts1511–
Exhaust Manifold Retaining Nuts2518–
Flexible Plate Bolts6044–
Flexible Plate Inspection Cover Bolts10–89
Flywheel Bolts35
+ 30° + 15°25
+ 30° + 15°–
Flywheel Inspection Cover Bolts12–106
Front Timing Belt Cover Bolts (Upper and Lower)10–89
Fuel Rail Assembly Retaining Bolts2518–
Fuel Rail Retaining Bolts2518–
Generator Upper Retaining Bolt2015–
Intake Camshaft Gear Bolt67.549–
Intake Manifold Retaining Bolts/Nuts2518–
Intake Manifold Support Bracket Lower Bolt2518–
Intake Manifold Support Bracket Upper Bolts2518–
Lower Front Timing Belt Cover Bolts10–89
Oil Pan Flange Bolts7555–
Oil Pan Retaining Bolts10–89
Oil Pan Drain Plug3526–
OIl Pressure Switch4030–

1C1 – 6I1.4L/1.6L DOHC ENGINE MECHANICAL
DAEWOO V–121 BL4
Application Lb–InLb–Ft NSm
Oil Pump Bolts10–89
Oil Pump Rear Cover Bolts8–71
Oil Pump Retaining Bolts10–89
Oil Suction Pipe or Support Bracket Bolts10–89
Rear Timing Belt Cover Bolts10–89
Safety Relief Valve Bolt303022–
Spark Plugs2518–
Thermostat Housing Mounting Bolts2015–
Timing Belt Automatic Tensioner Bolts2518–
Timing Belt Idler Pulley Bolt4030–
Transaxle Bell Housing Bolts7555–
Transaxle Torque Converter Bolts4533–
Upper Front Timing Belt Cover Bolts10–89
Water Pump Retaining Bolts10–89

1.4L/1.6L DOHC ENGINE MECHANICAL 1C1 – 7
DAEWOO V–121 BL4
SPECIAL TOOLS
SPECIAL TOOLS TABLE
J–42492
Timing Belt
Adjuster
KM–470–B
Angular Torque
Gauge
J–28467–B
Engine Assembly
Support Fixture
KM–427
Piston Pin
Service Set
KM–571–B
Gauge
KM–340–0
Cutter Set
Includes: KM–340–7
Guide Drift
KM–340–13
Cutters
KM–340–26
Cutters
KM–348
Valve Spring
Compressor
KM–653
Adapter