DODGE DART 2013 PF / 1.G Owners Manual

Wheel And Wheel Trim Care
•
All wheels and wheel trim, especially aluminum and
chrome plated wheels, should be cleaned regularly
with a mild soap and water to prevent corrosion.
•To remove heavy soil and/or excessive brake dust, use
MOPARWheel Cleaner or equivalent or select a
non-abrasive, non-acidic cleaner.
CAUTION!
Do not use scouring pads, steel wool, a bristle brush,
or metal polishes. Do not use oven cleaner. These
products may damage the wheel’s protective finish.
Avoid automatic car washes that use acidic solutions
or harsh brushes that may damage the wheel’s pro-
tective finish. Only MOPAR Wheel Cleaner or
equivalent is recommended.
Stain Repel Fabric Cleaning Procedure – If
Equipped
Stain Repel seats may be cleaned in the following man-
ner:
•Remove as much of the stain as possible by blotting
with a clean, dry towel.
•Blot any remaining stain with a clean, damp towel.
•For tough stains, apply MOPAR Total Clean or a mild
soap solution to a clean, damp cloth and remove the
stain. Use a fresh, damp towel to remove soap residue.
•For grease stains, apply MOPAR Multi-Purpose
Cleaner or a equivalent high quality cleaner to a clean,
damp cloth and remove the stain. Use a fresh, damp
towel to remove soap residue.
•Do not use any harsh solvents or any other form of
protectants on Stain Repel products.
7
MAINTAINING YOUR VEHICLE 549

Interior Care
Use MOPARTotal Clean or equivalent to clean fabric
upholstery and carpeting.
Use MOPAR Total Clean or equivalent to clean vinyl
upholstery.
MOPAR Total Clean or equivalent is specifically recom-
mended for leather upholstery.
Your leather upholstery can be best preserved by regular
cleaning with a damp, soft cloth. Small particles of dirt
can act as an abrasive and damage the leather upholstery
and should be removed promptly with a damp cloth.
Stubborn soils can be removed easily with a soft cloth
and MOPAR Total Clean or equivalent. Care should be
taken to avoid soaking your leather upholstery with any
liquid. Please do not use polishes, oils, cleaning fluids,
solvents, detergents, or ammonia based cleaners to clean
your leather upholstery. Application of a leather condi-
tioner is not required to maintain the original condition.WARNING!
Do not use volatile solvents for cleaning purposes.
Many are potentially flammable, and if used in
closed areas, they may cause respiratory harm.
Cleaning Headlights
Your vehicle has plastic headlights that are lighter and
less susceptible to stone breakage than glass headlights.
Plastic is not as scratch resistant as glass and, therefore,
different lens cleaning procedures must be followed.
To minimize the possibility of scratching the lenses and
reducing light output, avoid wiping with a dry cloth. To
remove road dirt, wash with a mild soap solution fol-
lowed by rinsing.
Do not use abrasive cleaning components, solvents, steel
wool or other aggressive material to clean the lenses.
550 MAINTAINING YOUR VEHICLE

Glass Surfaces
All glass surfaces should be cleaned on a regular basis
with MOPARGlass Cleaner or any commercial
household-type glass cleaner. Never use an abrasive type
cleaner. Use caution when cleaning the inside rear win-
dow equipped with electric defrosters or the right rear
quarter window equipped with the radio antenna. Do
not use scrapers or other sharp instruments which may
scratch the elements. When cleaning the rearview mirror,
spray cleaner on the towel or rag that you are using. Do
not spray cleaner directly on the mirror.
Instrument Panel Cover
The instrument panel cover has a low glare surface which
minimizes reflections on the windshield. Do not use
protectants or other products which may cause undesir-
able reflections. Use soap and warm water to restore the
low glare surface.
Instrument Panel Bezels
CAUTION!
When installing hanging air fresheners in your ve-
hicle, read the installation instructions carefully.
Some air fresheners will damage the finish of
painted or decorated parts if allowed to directly
contact any surface.
Cleaning Plastic Instrument Cluster Lenses
The lenses in front of the instruments in this vehicle are
molded in clear plastic. When cleaning the lenses, care
must be taken to avoid scratching the plastic.
1. Clean with a wet, soft rag. A mild soap solution may
be used, but do not use high alcohol content or abrasive
cleaners. If soap is used, wipe clean with a clean, damp
rag.
2. Dry with a soft cloth.
7
MAINTAINING YOUR VEHICLE 551

Seat Belt Maintenance
Do not bleach, dye or clean the seat belts with chemical
solvents or abrasive cleaners. This will weaken the fabric.
Sun damage can also weaken the fabric.
If the seat belts need cleaning, use a mild soap solution or
lukewarm water. Do not remove the seat belts from the
car to wash them. Dry with a soft cloth.
Replace the seat belts if they appear frayed or worn or if
the buckles do not work properly.
FUSES
Interior Fuses
Cavity CartridgeFuseMini
Fuse Description
F1 — 20 Amp
Yellow Front Heated Seats
F2 — 20 Amp
Yellow
Rear Heated Seats,
Heated Steering Wheel
Cavity Cartridge FuseMini
Fuse Description
F3 — 10 Amp
RedPAM, Rear Camera,
LBSS, RBSS, Com-
pass
F4 — 15 Amp
BlueIPC
F5 — 10 Amp
RedHVAC, Humidity
Sensor, In-Car Tem-
perature Sensor, In-
side Mirror Assem-
bly
F18 — 15 Amp
BlueRadio
F19 — 10 Amp
RedFuel Door
F20 — 10 Amp
RedSCCM, SAS, Switch
Bank
552 MAINTAINING YOUR VEHICLE

Cavity CartridgeFuseMini
Fuse Description
F21 — 10 Amp
RedDiagnostic Port
F22 — 10 Amp
RedUGDO, EOM
F23 — 20 Amp
Yellow Sunroof
F24 — 5 Amp
Ta nDirect Battery For
Underhood PDC
(RLY Coils)
F25 — 5 Amp
Ta nDDCT Feed #4
F26 — 5 Amp
Ta nStop Lamp Switch
F27 — 10 Amp
Red
Pneumatic Lumbar
Support (Solenoid),
Pneumatic Lumbar
Support (Pump Motor)
Underhood Fuses
The Integrated Power Module is located on the right side
of the engine compartment, behind the battery.
Cavity Maxi Fuse Mini Fuse Description
F01 70 Amp Ta n — Direct Battery
Feed #1 To BCM
Integrated Power Module
7
MAINTAINING YOUR VEHICLE 553

Cavity Maxi Fuse Mini Fuse DescriptionF02 60 Amp Blue — Direct Battery
Feed #2 To BCM
F03 30 Amp Green — Output For Starter
Relay #1
F04 40 Amp Orange — ESP Pump Motor
F05 40 Amp Orange — DDCT Feed #1
(SDU)
F06 30 Amp Green — Direct Battery
Feed #3 To BCM
F07 40 Amp Orange — EBL RLY Coil,
Blower Motor RLY
Coil
F09 — 5 Amp Tan Radiator Fan En- able RLY, Radiator
Fan Enable RLY
CoilCavity Maxi Fuse Mini Fuse Description
F10 — 10 Amp RedORC
F11 — 20 Amp YellowECM, EPS, Backup
Lamp Switch
F14 — 15 Amp BlueDDCT Feed #2
F15 — 15 Amp BlueDDCT Feed #3
F16 — 15 Amp BlueIgnition Coils, Coil
Capacitor
F17 — 15 Amp BlueESC, Brake Pedal
Switch, OCM
F18 — 20 Amp YellowECM
F19 — 10 Amp RedA/C Compressor
Clutch
554 MAINTAINING YOUR VEHICLE

Cavity Maxi Fuse Mini Fuse DescriptionF20 — 30 Amp GreenEBL
F21 — 20 Amp YellowFuel Pump
F22 — 10 Amp RedORC
F23 — 25 Amp NaturalESC
F24 — 20 Amp YellowECM, Fuel Injec-
tors, Active Grill
Shutter (AGS)
F30 — 20 Amp YellowPower Outlet
(Console)
F81 60 Amp Blue — Interior PDC Bat-
tery Feed, Power
Seats
F82 30 Amp Green — AmplifierCavity Maxi Fuse Mini Fuse Description
F83 40 Amp Orange — HVAC Blower Mo-
tor
F84 — 20 Amp YellowCigar Lighter
F85 — 10 Amp RedSunroof, LRSM,
Power Outlet
(Console), UCI/
AUX Port, Cigar
Lighter
F86 — 20 Amp Yellow—
F87 — 10 Amp RedWastegate, Purge
Solenoid, OBD
Vent Valve, Oxy-
gen Sensor Heat-
ers
F88 — 10 Amp RedHeated Outside
Mirrors
7
MAINTAINING YOUR VEHICLE 555

VEHICLE STORAGE
If you will not be using your vehicle for more than
21 days, you may want to take steps to preserve your
battery.
•Disconnect the negative cable from the battery.
•Anytime you store your vehicle, or keep it out of
service (i.e., vacation) for two weeks or more, run the
air conditioning system at idle for about five minutes
in the fresh air and high blower setting. This will
ensure adequate system lubrication to minimize the
possibility of compressor damage when the system is
started again.
NOTE: When the vehicle has not been started or driven
for at least 35 days, an Extended Park Start Procedure is
required to start the vehicle. Refer to “Starting Proce-
dures” in “Starting And Operating” for further informa-
tion.
REPLACEMENT BULBS
Interior Lights Bulb Type
Dome Lamp ........................... W5W
Overhead Console Lamp .................. W5W
Exterior Lights Bulb Type
Low Beam/High Beam (Bi-Halogen Headlamp) . . HIR2
Low Beam/High Beam (Bi-Xenon Headlamp) .... D3S
Front Park/Turn Signal Lamp ...........7442NALL
Sidemarker Lamp ........................ 194
Front Fog Lamp ......................... H11
Center High-Mounted Stop Lamp (CHMSL) ..... LED
(Serviced at Authorized Dealer)
Rear Tail/Stop/Turn Signal Lamp ............ LED
(Serviced at Authorized Dealer)
Backup Lamp .......................... 7440
License Lamp ........................... 168
556 MAINTAINING YOUR VEHICLE

BULB REPLACEMENT
Headlamps
Halogen Headlamps
Can be serviced by removing the cap from the backside
of the headlamp. Remove the HIR2 bulb from the con-
nector and replacing the bulb. Reinstall bulb and cap.
High Intensity Discharge Headlamps (HID)
The headlamps are a type of high voltage discharge tube.
High voltage can remain in the circuit even with the
headlamp switch off and the key removed.Because of
this, you should not attempt to service a headlamp bulb
yourself. If a headlamp bulb fails, take your vehicle to
an authorized dealer for service.
WARNING!
A transient high voltage occurs at the bulb sockets of
HID headlamps when the headlamp switch is turned
ON. It may cause serious electrical shock or electro-
cution if not serviced properly. See your authorized
dealer for service.
NOTE: On vehicles equipped with HID headlamps,
when the headlamps are turned on, there is a blue hue to
the lights. This diminishes and becomes more white after
approximately 10 seconds, as the system charges.
7
MAINTAINING YOUR VEHICLE 557

Backup Lamps
1. Open trunk.
2. Remove trim cover.3. Twist the bulb socket one quarter turn counter clock-
wise to remove.
4. Replace bulb.
558 MAINTAINING YOUR VEHICLE