display DODGE DURANGO 2017 3.G Owners Manual

NOTE:You can insert the double-sided emergency key
into the lock cylinders with either side up.
Ignition Or Accessory On Message
Upon opening the driver’s door when the ignition is in
ACC or ON (engine not running), a chime will sound to
remind you to cycle the ignition to OFF. In addition to the
chime, the ignition or accessory on message will display in
the cluster. NOTE:
With the Uconnect system, the power window
switches, radio, power sunroof (if equipped), and power
outlets will remain active for up to 10 minutes after the
ignition is cycled to the OFF position. Opening either front
door will cancel this feature. The time for this feature is
programmable. Refer to “Uconnect Settings” in “Under-
standing Your Instrument Panel” for further information.
WARNING!
• Before exiting a vehicle, always shift the automatic
transmission into PARK and apply the parking
brake. Always make sure the keyless ignition node is
in the “OFF” mode, remove the key fob from the
vehicle and lock the vehicle.
• Never leave children alone in a vehicle, or with
access to an unlocked vehicle.
• Allowing children to be in a vehicle unattended is
dangerous for a number of reasons. A child or others
could be seriously or fatally injured. Children
should be warned not to touch the parking brake,
brake pedal or the gear selector.
(Continued)
Emergency Key Removal
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13

How To Use Remote Start
All of the following conditions must be met before the
engine will remote start:
•Gear Selector in PARK
• Doors closed
• Hood closed
• Liftgate closed
• Hazard switch off
• Brake switch inactive (brake pedal not pushed)
• Battery at an acceptable charge level
• PANIC
button not pushed
•System not disabled from previous remote start event
• Vehicle alarm system indicator flashing
• Ignition in STOP/OFF position
• Fuel level meets minimum requirement
• Vehicle Security Alarm is not signaling an intrusion
WARNING!
•Do not start or run an engine in a closed garage or
confined area. Exhaust gas contains Carbon Monox-
ide (CO) which is odorless and colorless. Carbon
Monoxide is poisonous and can cause serious injury
or death when inhaled.
• Keep key fobs away from children. Operation of the
Remote Start System, windows, door locks or other
controls could cause serious injury or death.
Remote Start Abort Message — If Equipped
The following messages will display in the instrument
cluster display if the vehicle fails to remote start or exits
remote start prematurely:
• Remote Start Aborted — Door Ajar
• Remote Start Aborted — Hood Ajar
• Remote Start Aborted — Liftgate Ajar
• Remote Start Aborted — Fuel Low
• Remote Start Disabled — Start Vehicle To Reset
The Remote Start Abort message stays active until the
ignition is turned to the ON/RUN position.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

To Enter Remote Start Mode
Push and release the REMOTE START buttonon the
key fob twice within five seconds. The vehicle doors will
lock, the parking lights will flash, and the horn will
chirp twice (if programmed). Then, the engine will start,
and the vehicle will remain in the Remote Start mode for
a 15-minute cycle.
NOTE:
• If an engine fault is present or fuel level is low, the
vehicle will start and then shut down in 10 seconds.
• The park lamps will turn on and remain on during
Remote Start mode.
• For security, power window and power sunroof opera-
tion (if equipped) are disabled when the vehicle is in the
Remote Start mode.
• The engine can be started two consecutive times with
the key fob. However, the ignition must be cycled by
pushing the START/STOP button twice (or the ignition
switch must be cycled to the ON/RUN position) before
you can repeat the start sequence for a third cycle.
To Exit Remote Start Mode Without Driving The
Vehicle
Push and release the REMOTE STARTbutton one time
or allow the engine to run for the entire 15-minute cycle.
NOTE: To avoid unintentional shutdowns, the system will
disable with a one time push of the REMOTE START
button for two seconds after receiving a valid Re-
mote Start request.
To Exit Remote Start Mode And Drive The Vehicle
Before the end of 15-minute cycle, push and release the
UNLOCK button on the key fob to unlock the doors and
disarm the Vehicle Security Alarm (if equipped). Then,
prior to the end of the 15-minute cycle, push and release
the START/STOP button.
NOTE:
• For vehicles equipped with the Keyless Enter-N-Go —
Passive Entry feature, the message “Remote Start Active
— Push Start Button” will display in the cluster display
until you push the START button.
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25

▫Windshield Washer Operation ..............145
▫ Mist ............................... .146
▫ Rain Sensing Wipers — If Equipped .........146
 TILT/TELESCOPING STEERING COLUMN .....147
 POWER TILT/TELESCOPING STEERING COLUMN
— IF EQUIPPED ....................... .148
 HEATED STEERING WHEEL — IF EQUIPPED . .149
 ELECTRONIC SPEED CONTROL — IF
EQUIPPED ........................... .150
▫ To Activate .......................... .150
▫ To Set A Desired Speed ..................151
▫ To Deactivate ........................ .151
▫ To Resume Speed ..................... .151
▫ To Vary The Speed Setting ................151
▫ To Accelerate For Passing .................152
 ADAPTIVE CRUISE CONTROL (ACC) —
IF EQUIPPED ......................... .153
▫ Adaptive Cruise Control (ACC) Operation .....155▫
Activating Adaptive Cruise Control (ACC) .....155
▫ To Activate/Deactivate ...................156
▫ To Set A Desired ACC Speed ...............157
▫ To Cancel ........................... .158
▫ ToTurnOff.......................... .158
▫ To Resume .......................... .158
▫ To Vary The Speed Setting ................159
▫ Setting The Following Distance In ACC .......161
▫ Overtake Aid ......................... .163
▫ ACC Operation At Stop ..................164
▫ Adaptive Cruise Control (ACC) Menu ........164
▫ Display

Warnings And Maintenance .........165
▫ Precautions While Driving With ACC .........167
▫ General Information .....................171
▫ Normal (Fixed Speed) Electronic Speed Control
Mode .............................. .171
 FORWARD COLLISION WARNING (FCW) WITH
MITIGATION — IF EQUIPPED ..............174
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91

▫Forward Collision Warning (FCW) With Mitigation
Operation ........................... .174
▫ Turning FCW ON Or OFF .................176
▫ Changing FCW And Active Braking Status .....176
▫ FCW Limited Warning...................177
▫ Service FCW Warning ....................177
 LANESENSE — IF EQUIPPED ..............178
▫ LaneSense Operation ....................178
▫ Turning LaneSense ON Or OFF .............179
▫ LaneSense Warning Message ...............180
▫ Changing LaneSense Status ................182
 PARKSENSE REAR PARK ASSIST —
IF EQUIPPED ......................... .183
▫ ParkSense Sensors ..................... .184
▫ ParkSense Warning Display ................184
▫ ParkSense Display ..................... .185
▫ Enabling And Disabling ParkSense ..........190
▫ Service The ParkSense Rear Park Assist System. .190 ▫
Cleaning The ParkSense System .............190
▫ ParkSense System Usage Precautions .........191
 PARKVIEW REAR BACK UP CAMERA —
IF EQUIPPED ......................... .192
 OVERHEAD CONSOLE ...................194
▫ Front Map/Reading Lights — If Equipped . . . .194
▫ Courtesy Lights ....................... .195
▫ Sunglasses Bin Door ....................196
 GARAGE DOOR OPENER — IF EQUIPPED . . . .196
▫ Before You Begin Programming HomeLink .....197
▫ Programming A Rolling Code ..............197
▫ Pr

ogramming A Non-Rolling Code ..........199
▫ Canadian/Gate Operator Programming .......200
▫ Using HomeLink ...................... .201
▫ Security ............................. .201
▫ Troubleshooting Tips ....................201
▫ General Information .....................202
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

If the 9-1-1 Call system detects a malfunction, any of the
following may occur at the time the malfunction is de-
tected, and at the beginning of each ignition cycle:
•The rearview mirror light located between the ASSIST
and 9-1-1 buttons will continuously be illuminated red.
• The Instrument Cluster Display will show the following
message “Vehicle device requires service. Please contact
your dealer.”
• An In-Vehicle Audio message will state “Vehicle device
requires service. Please contact your dealer.”
WARNING!
• Ignoring the rearview mirror light could mean you
will not have 9-1-1 Call services. If the rearview
mirror light is illuminated, have an Authorized
Dealer service the 9-1-1 Call system immediately.
• The Occupant Restraint Control module turns on the
Air Bag Warning Light on the instrument panel if a
malfunction in any part of the system is detected. If
the Air Bag Warning Light is illuminated, have an
Authorized Dealer service the Occupant Restraint
Control system immediately. Even if the 9-1-1 Call system is fully functional, factors
beyond FCA US LLC’s control may prevent or stop the
9-1-1 Call system operation. These include, but are not
limited to, the following factors:
•
Delayed accessories mode is active.
• The ignition is in the OFF position.
• The vehicle’s electrical systems are not intact.
• The 9-1-1 Call system software and/or hardware are
damaged during a crash.
• The vehicle battery loses power or becomes discon-
nected during a vehicle crash.
• 1X(voice/data) or 3G(data) network and/or Global Po-
sitioning Satellite signals are unavailable or obstructed.
• Equipment malfunction at the 9-1-1 operator facility.
• Operator error by the 9-1-1 operator.
• 1X(voice/data) or 3G(data) network congestion.
• Weather.
• Buildings, structures, geographic terrain, or tunnels.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Heated Seats — If Equipped
On some models, the front and rear seats may be equipped
with heaters located in the seat cushions and seat backs.
WARNING!
•Persons who are unable to feel pain to the skin
because of advanced age, chronic illness, diabetes,
spinal cord injury, medication, alcohol use, exhaus-
tion or other physical condition must exercise care
when using the seat heater. It may cause burns even
at low temperatures, especially if used for long
periods of time.
• Do not place anything on the seat or seatback that
insulates against heat, such as a blanket or cushion.
This may cause the seat heater to overheat. Sitting in
a seat that has been overheated could cause serious
burns due to the increased surface temperature of the
seat.
Front Heated Seats
The front heated seats control buttons are located within
the climate or controls screen of the touchscreen.
You can choose from HI, LO or OFF heat settings. The
indicator arrows in touchscreen buttons indicate the level
of heat in use. Two indicator arrows will illuminate for HI,
one for LO and none for OFF.
• Press the heated seat button
once to turn the HI
setting ON.
• Press the heated seat buttona second time to turn
the LO setting ON.
• Press the heated seat buttona third time to turn the
heating elements OFF.
If the HI-level setting is selected, the system will automati-
cally switch to LO-level after approximately 60 minutes of
continuous operation. At that time, the display will change
from HI to LO, indicating the change. The LO-level setting
will turn OFF automatically after approximately 45 minutes.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115

Power Folding Third Row Head Restraints
For improved visibility when in reverse, the third row head
restraints can be folded using the Uconnect System.
Press the “Controls” button located on the bottom of the
Uconnect display.
Press the Headrest Fold button
to power fold the third
row head restraints.
NOTE:
• The head restraints can only be folded downward using
the Headrest button. The head restraints must be raised
manually when occupying the third row.
• Do not fold if there are passengers seated in the third
row seats.
60/40 Split Rear Seat
Fold-Flat
The second row seats can be folded flat to carry cargo.
Pull upward on the release lever located on the outboard
side of the seat.
Release Lever
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123

Programming The Memory Feature
NOTE:To create a new memory profile, perform the
following:
1. Cycle the vehicles ignition to the ON/RUN position (Do not start the engine).
2.
Adjust all memory profile settings to desired preferences
(i.e., seat, side mirror, power tilt and telescopic steering
column [if equipped], and radio station presets).
3. Push and release the S (Set) button on the memory switch.
4. Within five seconds, push and release either of the memory buttons (1) or (2). The Instrument Cluster
Display will show which memory position has been set.
NOTE:
•
Memory profiles can be set without the vehicle in PARK,
but the vehicle must be in PARK to recall a memory profile.
• To set a memory profile to your key fob, refer to
“Linking And Unlinking The Remote Keyless Entry Key
Fob To Memory” in this section.
Linking And Unlinking The Remote Keyless Entry
Key Fob To Memory
Your key fobs can be programmed to recall one of two
pre-programmed memory profiles by pushing the UN-
LOCK button on the key fob.
NOTE: Before programming your key fobs you must select
the “Memory Linked To FOB” feature through the
Uconnect system screen. Refer to “Uconnect Settings ” in
“Understanding Your Instrument Panel” for further infor-
mation.
To program your key fobs, perform the following:
1. Cycle the vehicles ignition to the OFF position.
2. Select a desired memory profile (1) or (2).
NOTE: If a memory profile has not already been set, refer
to Programming The Memory Feature in this section for
instructions on how to set a memory profile.
3. Once the profile has been recalled, push and release the SET (S) button on the memory switch.
4. Within five seconds, push and release button (1) or (2) accordingly. “Memory Profile Set” (1 or 2) will display
in the instrument cluster.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131

5. Within 10 seconds, Push and release the LOCK buttonon the key fob.
NOTE: Your key fobs can be unlinked to your memory
settings by pushing the SET (S) button, and within 10
seconds, followed by pushing the UNLOCK button on the
key fob.
Memory Position Recall
NOTE: The vehicle must be in PARK to recall memory
positions. If a recall is attempted when the vehicle is not in
PARK, a message will be displayed in the Instrument
Cluster Display.
Driver One Memory Position Recall
• To recall the memory settings for driver one using the
memory switch, push MEMORY button number 1 on the
memory switch.
• To recall the memory settings for driver one using the
key fob, push the UNLOCK button on the key fob linked
to memory position 1. Driver Two Memory Position Recall
•
To recall the memory setting for driver two using the
memory switch, push MEMORY button number 2 on the
memory switch.
• To recall the memory settings for driver two using the
key fob, push the UNLOCK button on the key fob linked
to memory position 2.
A recall can be cancelled by pushing any of the MEMORY
buttons during a recall (S, 1, or 2). When a recall is
cancelled, the driver’s seat and steering column (if
equipped) stop moving. A delay of one second will occur
before another recall can be selected.
Easy Entry/Exit Seat
This feature provides automatic driver seat positioning to
enhance driver mobility when entering and exiting the
vehicle.
The distance the driver seat moves depends on where you
have the driver seat positioned when you cycle the vehi-
cle’s ignition to the OFF position.
• When you cycle the vehicle’s ignition to the OFF posi-
tion, the driver seat will move about 2.4 inches (60 mm)
rearward if the driver seat position is greater than or
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE