flat tire DODGE DURANGO 2020 Vehicle Warranty

EXAMPLE:
Load Identification:
Absence of the following load identification symbols on the sidewall of th etire
indicates a Standard Load (SL) tire:
• XL
= Extra load (or reinforced) tire, or
• LL = Light load tire or
• C, D, E, F, G = Load range associated with the maximum load a tire can carry
at a specified pressure
Maximum Load–Maximum load indicates the maximum loadthistireisdesigned 
to carry
Maximum Pressure– Maximum pressure indicates the maximum permissible cold 
tire inflation pressure for this tire
TireIdentification Number (TIN)
The
TIN
may
be
found
on
one
or
both
sides
of
the
tire;
however,
the
date

code
may
only
be
on
one
side.
Ti re s
with
white
sidewalls
will
have
the

full
TIN,
including
the
date
code,
located
on
the
white
sidewall
side
of

the
tire.
Look
for
the
TIN
on
the
outboard
side
of
black
sidewall

tires
as

mounted
on
the
vehicle.
If
the
TIN
is
not
found
on
the
outboard
side,
then

you
will
find
it
on
the
inboard
side
of
the
tire.
EXAMPLE:
DOT MAL9ABCD 0301
DOT =Department 2fTransportation
– This symbolcertifies that thetireisin compliance with theUSDepartment
of Transportation tire safety standards and is approved for highway use
MA =Code representing the tiremanufacturing location (two digits)
L9 =Code representing the tiresize (two digits)
ABCD = Code used by the tiremanufacturer (one to four digits)
03 =Number representing the week in which thetirewas manufactured (twodigits)
–03 means the 3rd week
01 =

Number representing the year inwhich thetirewas manufactured (twodigits)
– 01 means the year 2001
– Prior to July 2000, tire manufacturers were only required to have one number
to represent the year in which the tire was manufactured. Example: 031 coul d
represent the 3rd week of 1981 or 1991
TIRES
6

Tire Terminology And Definitions
TermDefinition
B-Pillar The vehicle B-Pillar is the structural member of
the body located behind the front door.
Cold Tire Inflation Pressure Cold tire inflation pressure is defined as the tire
pressure after the vehicle has not been driven
for at least three hours, or driven less than 1
mile (1.6 km) after sitting for a minimum of three
hours. Inflation pressure is measured in units of
PSI (pounds per square inch) or kPa
(kilopascals).
Maximum Inflation Pressure The maximum inflation pressure is the
maximum permissible cold tire inflation pressure
for this tire. The maximum inflation pressure is
molded into the sidewall.
Recommended Cold Tire Inflation Pressure Vehicle manufacturer’s recommended cold tire
inflation pressure as shown on the tire placard.
Tire Placard A label permanently attached to the vehicle
describing the vehicle’s loading capacity, the
original equipment tire sizes and the
recommended cold tire inflation pressures. TIRES
7

TireLoading And TirePressure
NOTE:

The
proper
cold
tire
inflation
pressure
is
listed
on
the
driver ’s
side
B-
Pillar
or
the
rear
edge
of
the
driver’s
side
door.
Check
the
inflation
pressure
of
each
tire,
including
the
spare
tire
(if

equipped),
at
least
monthly
and
inflate
to
the
recommended
pressure
for

your
vehicle.
Example Tire Placard Location (Door)
Example Tire Placard Location (B-Pillar)
TIRES
8

Tire And Loading Information Placard
This placard tells you important information about the:v 5IF
Oumber
of
people
that
can
be
carried
in
the
vehicle.
v 5IF
Uotal
weight
your
vehicle
can
carry.
v TIF
Uire
size
designed
for
your
vehicle.
v 5IF
Dold
tire
inflation
pressures
for
the
front,
rear,
and
spare
tires.
Tire And Loading Information Placard
TIRES
Loading
The
vehicle
maximum
load
on
the
tire
must
not
exceed
the
load
carrying

capacity
of
the
tire
on
your
vehicle.
Yo u
will
not
exceed
the
tire’s
load

carrying
capacity
if
you
adhere
to
the
loading
conditions,
tire
size,
and

cold
tire
inflation
pressures
specified
on
the
Ti re
and
Loading
Informa-
tion
placard
in
“Vehicle
Loading”
in
the

“Starting
And
Operating”

section
of
your
Owner ’s
Manual.
NOTE:
Under
a
maximum
loaded
vehicle
condition,
gross
axle
weight
ratings

(GAWRs)
for
the
front
and
rear
axles
must
not
be
exceeded.
For
further
information
on
GAWRs,
vehicle
loading,
and
trailer
towing,

refer
to
“Vehicle
Loading”
in
the
“Starting
And
Operating”
section

of
your
Owner ’s
Manual.
To
determine
the
maximum


loading
conditions
of
your
vehicle,
locate
the

statement
“The
combined
weight
of
occupants
and
cargo
should
never
9

Tires — General Information
Tire Pressure
Proper tire inflation pressure is essential to the safe and satisfactory
operation of your vehicle. Four primary areas are affected by improper
tire pressure:
•Safety and Vehicle Stability
• Economy
• Tread Wear
• Ride Comfort
Safety
WARNING!
• Improperly inflated tires are dangerous and can cause collisions.
• Underinflation
increases
tire
flexing
and
can
result
in
overheating
and
tire
failure.
• Overinflation
reduces
a
tire’s
ability
to
cushion
shock.
Objects
on
the
road
and
chuckholes
can
cause
damage
that
result
in
tire
failure.
• Overinflated or underinflated tires can affect vehicle handling and
can fail suddenly, resulting in loss of vehicle control.
• Unequal tire pressures can cause steering problems. You could lose
control of your vehicle.
• Unequal tire pressures from one side of the vehicle to the other can
cause the vehicle to drift to the right or left.
• Always drive with each tire inflated to the recommended cold tire
inflation pressure.
Both
underinflation
and
overinflation
affect
the
stability
of
the
vehicle

and
can
produce
a
feeling
of
sluggish

response
or
over
responsiveness
in

the
steering.
NOTE:
• Unequal tire pressures from side to side may cause erratic and
unpredictable steering response.
• Unequal tire pressure from side to side may cause the vehicle to drift
left or right.
TIRES
12

Fuel
Economy
Underinflated
tires
will
increase
tire
rolling
resistance
resulting
in
higher

fuel
consumption.
Tread
Wear
Improper
cold
tire
inflation
pressures
can
cause
abnormal
wear
patterns

and
reduced
tread
life,
resulting
in
the
need
for
earlier
tire
replacement.
Ride
Comfort
And
Vehicle
Stability
Proper
tire
inflation
contributes
to
a
comfortable
ride.
Overinflation

produces
a
jarring
and
uncomfortable
ride.
TireInflation Pressures
The
proper
cold
tire
inflation
pressure
is
listed
on
the
driver’s
side

B-Pillar
or
rear
edge
of
the
driver’s
side
door.
At
least
once
a
month:
• Check

and
adjust
tire
pressure
with
a
good
quality
pocket-type
pressure
gauge.
Do
not
make
a
visual
judgement
when
determining
proper
inflation.
Tires
may
look
properly
inflated
even
when
they
are
underinflated.
• Inspect tires for signs

of tire wear or visible damage.
CAUTION!
After inspecting or adjusting the tire pressure, always reinstall the
valve stem cap. This will prevent moisture and dirt from entering the
valve stem, which could damage the valve stem.
Inflation pressures specified on the placard are always “cold tire inflation
pressure”. Cold tire inflation pressure is defined as the tire pressure after
the vehicle has not been driven for at least three hours, or driven less than
1 mile (1.6 km) after sitting for a minimum of three hours. The cold tire
inflation pressure must not exceed the maximum inflation pressure
molded into the tire sidewall.
Check tire pressures more often if subject to a wide range of outdoor
temperatures, as tire pressures vary with temperature changes.
Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air
temperature change. Keep this in mind when checking tire pressure
inside a garage, especially in the Winter.
TIRES
13

Example:
If
garage
temperature
=
68°F
(20°C)
and
the
outside
tempera-
ture
=
32°F
(0°C)
then
the
cold
tire
inflation
pressure
should
be
increased

by
3
psi
(21
kPa),
which
equals
1
psi
(7
kPa)
for
every
12°F
(7°C)
for
this

outside
temperature
condition.
Ti re
pressure
may
increase
from
2
to
6
psi
(13
to
40
kPa)
during
operation.

DO
NOT
reduce
this
normal
pr

essure
build
up
or
your
tire
pressure
will

be
too
low.
Tire Pressures For High Speed Operation
The
manufacturer
advocates
driving
at
safe
speeds
and
within
posted

speed
limits.
Where
speed
limits
or
conditions
are
such
that
the
vehicle

can
be
driven
at
high
speeds,
maintaining
correct
tire
inflation
pressure
is

very
important.
Increased
tire
pressure
and
reduced
vehicle
loading
may

be
required
for
high
speed
vehicle
operation.
Refer
to
an
authorized
tire

dealer
or
original
equipment
vehicle
dealer
for
recommended
safe

operating
speeds,


loading
and
cold
tire
inflation
pressures.
WARNING!
High speed driving with your vehicle under maximum load is
dangerous. The added strain on your tires could cause them to fail.
You could have a serious collision. Do not drive a vehicle loaded to
the maximum capacity at continuous speeds above 75 mph
(120 km/h).
Radial Ply Tires
WARNING!
Combining radial ply tires with other types of tires on your vehicle
will cause your vehicle to handle poorly. The instability could cause
a collision. Always use radial ply tires in sets of four. Never combine
them with other types of tires.
TIRES
14

Tire Repair
If your tire becomes damaged, it may be repaired if it meets the following
criteria:
•The tire has not been driven on when flat.
• The damage is only on the tread section of your tire (sidewall damage
is not repairable).
• The puncture is no greater thana¼ofaninch (6 mm).
TIRES
Consult
an
authorized
tire
dealer
for
tire
repairs
and
additional
informa-
tion.
Run FlatTires —IfEquipped
Run
G lat
tires
allow
you
the
capability
to
drive
50
miles
(80
km)
at
50
mph

(80
km/h)
after
a
rapid
loss
of
inflation
pressure.
This
rapid
loss
of

inflation
is
referred
to
as
the
S un
Glat
mode.
A
Sun
G lat
mode
occurs

when
the
tire
inflation
pressure
is
of/or
below
14
psi
(96
kPa).
Once
a

Sun
G lat
tire
reaches
the
run
flat
mode
it
has
limited
driving
capabilities

and
needs
to
be
replaced
immediately.
A
Sun
Glat


tire
is
not
repairable.
%BNBHFE
SVO
GMBU
UJSFT

PS
SVO
GMBU
UJSFT
UIBU
IBWF
FYQFSJFODFE
B
MPTT
PG
QSFTTVSF

TIPVME
CF
SFQMBDFE
JNNFEJBUFMZ
XJUI
BOPUIFS
SVO
GMBU
UJSF
PG
JEFOUJDBM
TJ[F
BOE

TFSWJDF
EFTDSJQUJPO
-PBE
*OEFY
BOE
4QFFE
4ZNCPM

It
is
not
recommended
driving
a
vehicle
loaded
at
full
capacity
or
to
tow

a
trailer
while
a
tire
is
in
the
run
flat
mode.
See
the
tire
pressure
monitoring
section
for
more
information.
TireSpinning
When
stuck
in
mud,
sand,
snow,
or
ice
conditions,
do
not
spin
your

vehicle’s
wheels
above
30
mph
(48
km/h)
or
for
longer
than
30
seconds

continuously
without
stopping.
Refer
to
“Freeing
A
Stuck
Vehicle”
in
“In
Case
Of
Emergency”
in
your

Owner ’s
Manual
for
further
information.
15

Life Of Tire
The service life of a tire is dependent upon varying factors including, but
not limited to:
•˜ž›1 riving
style
ï
• Tire pressure - Improper cold tire inflation pressures can cause uneven
wear patterns to develop across the tire tread. These abnormal wear
patterns will reduce tread life, resulting in the need for earlier tire
replacement.
• ‘Ž1 –’•Žœ
driven.
• Performance tires, tires with a speed rating of V or higher, and
Summer tires typically have a reduced tread life. Rotation of these tires
per the vehicle scheduled maintenance is highly recommended.
WARNING!
Tires and the spare tire should be replaced after six years, regardless
of the remaining tread. Failure to follow this warning can result in
sudden tire failure. You could lose control and have a collision
resulting in serious injury or death.
TIRES
Keep
dismounted
tires
in
a
cool,
dry
place
with
as
little
exposure
to
light

as
possible.
Protect
tires
from
contact
with
oil,
grease,
and
gasoline.
Replacement Tires
The
tires
on
your
new
vehicle
provide
a
balance
of
many
characteristics.

They
should
be
inspected
regularly
for
wear
and
correct
cold
tire

inflation
pressures.
The
manufacturer
strongly
recommends
that
you
use

tires
equivalent
to
the
originals
in
size,
quality
and
performance
when

replacement
is
needed.
Refer
to
the
paragraph
on
“Tread
Wear
Indica-
tors”
in
this


section
UP
EFUFSNJOF
JG
ZPVS
UJSFT
BSF
XPSO.
Refer
to
the
Tire
and

Loading
Information
placard
or
the
Vehicle
Certification
Label
for
the

size
designation
of
your
tire.
The
Load
Index
and
Speed
Symbol
for

your
tire
will
be
found
on
the
original
equipment
tire
sidewall.
See
the
Tire
Sizing
Chart
example
found
in
the
“Tire
Safety
Information”

section
of
this
manual
for
more
information
relating
to
the
Load
Index

and
Speed
Symbol
of
a
tire.
It
is
recommended
to
replace
the
two
front
tires
or
two
rear
tires
as
a
pair.

Replacing
just
one


tire
can
seriously
affect
your
vehicle’s
handling.
If
you
17

authorized
tire
dealer
for
recommended
safe
operating
speeds,
loading

and
cold
tire
inflation
pressures.
While
studded
tires
improve
performance
on
ice,
skid
and
traction

capability
on
wet
or
dry
surfaces
may
be
poorer
than
that
of
non-studded

tires.
Some
states
prohibit
studded
tires;
therefore,
local
laws
should
be

checked
before
using
these
tire
types.
Spare Tires—IfEquipped
NOTE:

For
vehicles
equipped
with
Tire
Service
Kit
instead
of
a
spare
tire,
please

refer
to
“Tire
Service
Kit”
in
“In
Case
Of
Emergency”
in
your

Owner ’s
Manual
for
further
information.
CAUTION!
Because of the reduced ground clearance, do not take your vehicle
through an automatic car wash with a compact or limited use
temporary spare installed. Damage to the vehicle may result.
TIRES
SpareTireMatching Original Equipped Tire And Wheel —If
Equipped
Your
vehicle
may
be
equipped
with
a
spare
tire
and
wheel
equivalent
in

look
and
function
to
the
original
equipment
tire
and
wheel
found
on
the

front
or
rear
axle
of
your
vehicle.
This
spare
tire
may
be
used
in
the
tire

rotation
for
your
vehicle.
If
your
vehicle
has
this
option,
refer
to
an

authorized
tire
dealer
for
the
recommended
tire
rotation
pattern.
Compact Spare Tire—IfEquipped
The
compact
spare
is
for
temporary
emergency
use
only.
Yo u
can
identify

if
your
vehicle
is
equipped
with
a
compact
spare
by
looking
at
the
spare

tire
description
on
the
Tire
and
Loading
Information
Placard
located
on

the
driver ’s
side
#QJMMBS

UIF
SFBS
FEHF
PG
UIF
ESJWFST
TJEF
EPPS
or
on
the

sidewall
of
the
tire.
Compact
spare
tire
descriptions
begin
with
the

letter
“T”
or
“S”
preceding
the
size
designation.
Example:
T145/80D18

103M.
T,
S
=
Temporary
Spare
Tire
Since
this


tire
has
limited
tread
life,
the
original
equipment
tire
should
be

repaired
(or
replaced)
and
reinstalled
on
your
vehicle
at
the
first

opportunity.
Do
not
install
a
wheel
cover
or
attempt
to
mount
a
conventional
tire
on

the
compact
spare
wheel,
since
the
wheel
is
designed
specifically
for
the
20