engine DODGE RAM 1999 Service Repair Manual

Courtesy of Chrysler Corp.
Removal (Ram Pickup)
1) EVAP leak detection pump and EVAP leak detection pump
filter must be replaced as an assembly. EVAP leak detection pump and
EVAP leak detection pump filter are located at passenger's side front
corner of engine compartment, near wheelwell. See Fig. 41.
2) Disconnect hose from bottom of EVAP leak detection pump
filter that goes to EVAP leak detection pump. Remove retaining bolt
and EVAP leak detection pump filter.
3) Disconnect electrical connector and vacuum hoses at EVAP
leak detection pump. Use care not to damage vacuum hoses during
removal. Remove retaining bolts and EVAP leak detection pump.
NOTE: Vacuum hoses and hose to EVAP leak detection pump filter must
be properly installed on EVAP leak detection pump and all
hoses must be in good condition. If hoses are not properly
installed or are damaged, a Diagnostic Trouble Code (DTC)
will be set in the Powertrain Control Module (PCM).
Installation
1) Install EVAP leak detection and EVAP leak detection pump
filter. Tighten retaining bolts to specification. See TORQUE
SPECIFICATIONS.
2) To install remaining components, reverse removal
procedure. Ensure vacuum hoses and hose to EVAP leak detection pump
filter are in good condition and properly installed on EVAP leak
detection pump.
Removal (Ram Van & Ram Wagon)
1) EVAP leak detection pump and EVAP leak detection pump
filter must be replaced as an assembly. EVAP leak detection pump and
EVAP leak detection pump filter are located on mounting bracket at
driver's side of engine compartment, near the wheelwell. See Fig. 42.
2) Disconnect electrical connector and vacuum hoses at EVAP
purge solenoid. Use care not to damage vacuum hoses during removal.
Remove EVAP purge solenoid from mounting bracket. Disconnect
electrical connector and vacuum hoses at EVAP leak detection pump. Use
care not to damage vacuum hoses during removal.
3) Remove retaining bolts from mounting bracket. Remove
mounting bracket with EVAP leak detection pump and EVAP leak detection
pump filter as an assembly. Remove retaining bolts, EVAP leak
detection pump and EVAP leak detection pump filter from mounting
bracket.
NOTE: All vacuum hoses and hose to EVAP leak detection pump filter
must be properly installed on EVAP leak detection pump and
all hoses must be in good condition. If hoses are not
properly installed or are damaged, a Diagnostic Trouble Code
(DTC) will be set in the Powertrain Control Module (PCM).
Installation
1) Install EVAP leak detection and EVAP leak detection pump
filter on mounting bracket. Tighten retaining bolts to specification.
See TORQUE SPECIFICATIONS.
2) To install remaining components, reverse removal
procedure. Ensure vacuum hoses and hose to EVAP leak detection pump
filter are in good condition and properly installed.

NOTE: EVAP purge solenoid may also be referred to as EVAP canister
purge solenoid, duty cycle solenoid or proportional purge
solenoid.
Removal & Installation (Dakota & Durango)
1) On Dakota 2.5L, EVAP purge solenoid is located on firewall
at passenger's side of engine compartment. See Fig. 43. On Dakota 3.
9L, 5.2L and 5.9L and Durango, EVAP purge solenoid is located at
driver's side of engine compartment, near brake booster. See Fig. 44.
2) On all models, disconnect electrical connector and vacuum
hoses at EVAP purge solenoid. Use care not to damage vacuum hoses
during removal. Remove retaining nuts and EVAP purge solenoid.
3) To install, reverse removal procedure. Tighten retaining
nuts to specification. See TORQUE SPECIFICATIONS. Ensure vacuum hoses
are in good condition and properly installed.
Fig. 43: Locating EVAP Purge Solenoid (Dakota 2.5L)
Courtesy of Chrysler Corp.

Fig. 44: Locating EVAP Purge Solenoid (Dakota 3.9L, 5.2L & 5.9L,
& Durango)
Courtesy of Chrysler Corp.
Removal & Installation (Ram Pickup, Ram Van & Ram Wagon)
1) On Ram Pickup, EVAP purge solenoid is located at
passenger's side front corner of engine compartment, near wheelwell.
See Fig. 41 .
2) On Ram Van and Ram Wagon, EVAP purge solenoid is located
at driver's side of engine compartment, near the wheelwell. See
Fig. 42 .
3) On all models, disconnect electrical connector and vacuum
hoses at EVAP purge solenoid. Use care not to damage vacuum hoses
during removal. Remove EVAP purge solenoid from mounting bracket.
4) To install reverse removal procedure. Ensure vacuum hoses
are in good condition and properly installed.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS

\









\









\









\









\









\









\







Application Ft. Lbs. (N.m)\
Crankshaft Position Sensor Bolt
2.5L ..................................................... 14 (19)\
3.9L, 5.2L & 5.9L ............................................ (1)
8.0L ......................................................... ( 1)
Downstream Oxygen Sensor ................................... 22 (30)\
Distributor Hold-Down Bolt ................................. 17 (23)\
EVAP Canister-To-Mounting Bracket Nut
Dakota & Durango ......................................... 17 (23)\
Ram Pickup ................................................... ( 2)
Ram Van & Ram Wagon .......................................... ( 3)
Fuel Pump Module Lock Nut
Dakota ................................................... 40 (54)\
Ram Pickup ............................................... 32 (43)\
Ram Van & Ram Wagon ...................................... 40 (54)\
Fuel Rail Bolt
2.5L ......................................................... ( 4)
3.9L, 5.2L & 5.9L ........................................ 17 (23)\
8.0L ..................................................... 11 (15)\
Fuel Tank Strap Nut
Dakota & Durango ......................................... 40 (54)\
Ram Pickup ............................................... 30 (41)\
Ram Van & Ram Wagon .......................................... ( 5)
IAT Sensor ................................................. 20 (27)\
Park/Neutral Switch ........................................ 25 (34)\
Power Steering Pressure Switch (2.5L) ...................... 16 (22\
)
Spark Plug ................................................. 30 (41)\
Throttle Body Bolt
2.5L ......................................................... ( 4)
3.9L, 5.2L & 5.9L ........................................ 17 (23)\
Throttle Body Nut (8.0L) ................................... 16 (22\
)
Upper Intake Manifold Bolt (8.0L) ...................... ( 6) 16 (22)
Upstream Oxygen Sensor ..................................... 22 (30)\
Wheel Lug Nut (Dakota & Durango) ......................... 100 (136\
)
INCH Lbs. (N.m)
Air Cleaner Housing-To-Throttle
Body Nut (Dakota & Durango) ............................. 96 (10.8\
)
Camshaft Position Sensor Bolt (8.0L) ...................... 50 (5.6\
)
Engine Coolant Temperature Sensor ........................ 96 (10.8)\
EVAP Canister Mounting Bracket-To
Body Nut (Ram Van & Ram Wagon) .......................... 95 (10.7\
)
EVAP Leak Detection Pump Filter
Bolt (Ram Pickup, Ram Van & Ram Wagon) ................... 65 (7.3\
)
EVAP Leak Detection Pump Bolt ............................. 11 (1.2)\
EVAP Purge Solenoid Nut (Dakota & Durango) ................ 75 (8.5\
)
IAC Motor Bolt ............................................ 60 (6.8)\
Ignition Coil Bolt/Nut
Dakota, Durango, Ram Van & Ram Wagon ......................... ( 7)
Ram Pickup
3.9L, 5.2L & 5.9L ........................................... ( 7)
8.0L .................................................. 90 (10.2)\
MAP Sensor Bolt
Dakota & Durango ........................................ 25 (2.8)\
Ram Pickup
3.9L, 5.2L & 5.9L ...................................... 25 (2.8)\
8.0L ................................................... 20 (2.3)\
Ram Van & Ram Wagon ..................................... 25 (2.8)\
PCM Bolt .................................................. 35 (4.0)\
TP Sensor Bolt ............................................ 60 (6.8)\

SCHEDULED SERVICES - NORMAL SERVICE (DIESEL)

1999 D odge P ic ku p R 1500
1997-99 MAINTENANCE
Chrysler Maintenance & Service Intervals
Diesel Engines
Normal Service
DODGE; RAM PICKUP Cummins Turbo Diesel: 5.9L VIN [D]
* READ THIS FIRST *
Before preforming maintenance on vehicle, ensure that all
cautions and warnings have been observed to prevent vehicle damage or
personal injury. See CAUTIONS & WARNINGS in MAINTENANCE INFORMATION
article in this section.
Introduction
The frequency of scheduled inspection and maintenance
services in this article are based on normal vehicle usage ONLY. The
following Severe conditions are NOT taken into account:
* Frequent short driving less than 5 Miles (8 Km).
* Frequent driving in dusty conditions.
* Frequent trailer towing.
* Extensive idling.
* More than 50% of your driving is at sustained high speeds
during hot weather, above 90
F (32C).
If the vehicle is operated mainly under any of these
conditions, this Normal service schedule article is inadequate. DO NOT
USE. Instead, use the Severe service schedule: See
SCHEDULED SERVICES - NORMAL SERVICE (DIESEL) .
6,000 MILE (10,000 KM)/6 MONTH NORMAL SERVICE
6,000 MILE (10,000 KM)/6 MONTH NORMAL SERVICE
\
\
\
\
\
\
\
 
INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


 Brake Hoses 


\
\
\
\
\
\
\


 Engine Coolant Level, Hoses & Clamps 

\
\
\
\
\
\
\



SERVICE 

\b\
\
\
\
\
\
\


 Rotate Tires 


\
\
\
\
\
\
\


 Lubricate Steering Linkage 

\
\
\
\
\
\
\



REPLACE 

\b\
\
\
\
\
\
\


 Engine Oil 


\
\
\
\
\
\
\


 Engine Oil Filter 

\
\
\
\
\
\
\



LUBRICATION SPECIFICATIONS 

\
\b\
\
\
\b\
\
\



Material  Condition  Specification 

\

\
\
\

\
\
\


 Engine Oil Ambient Temperature Above 10F SAE 15W-40 

(
1)  (-12C) To Over 30F (-1C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 10W-30 

0F (-18C) To Over 30F(-1C) 


\
\
\

\
\


Ambient Temperature Less Than  With Block Heater: 

-10F(-23C) Up To 0F (-18C) SAE 10W-30 

  Without Block Heater: 

  SAE 5W-30 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred for use in all Dodge 

trucks. Use only API approved oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


12,000 MILE (19,000 KM)/12 MONTH NORMAL SERVICE
12,000 MILE (19,000 KM)/12 NORMAL SERVICE
\
\
\
\
\
\
\
 
INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


 Brake Hoses 


\
\
\
\
\
\
\


 Engine Coolant Level, Hoses & Clamps 


\
\
\
\
\
\
\


 Water Pump Weep Hole For Blockage 

\
\
\
\
\
\
\



SERVICE 

\b\
\
\
\
\
\
\


 Rotate Tires 


\
\
\
\
\
\
\


 Lubricate Steering Linkage 


\
\
\
\
\
\
\


 Clean Fuel Strainer 

\
\
\
\
\
\
\



REPLACE 

\b\
\
\
\
\
\
\


 Engine Oil 


\
\
\
\
\
\
\


 Engine Oil Filter 


\
\
\
\
\
\
\


 Fuel Filter 

\
\
\
\
\
\
\



LUBRICATION SPECIFICATIONS 

\
\b\
\
\
\b\
\
\



Material  Condition  Specification 

\

\
\
\

\
\
\


Engine Oil Ambient Temperature Above 10F SAE 15W-40 

(
1)  (-12C) To Over 30F (-1C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 10W-30 

0F (-18C) To Over 30F(-1C) 


\
\
\

\
\


Ambient Temperature Less Than  With Block Heater: 

-10F(-23C) Up To 0F (-18C) SAE 10W-30 

  Without Block Heater: 

  SAE 5W-30 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred. Use only API approved 

oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


18,000 MILE (29,000 KM)/18 MONTH NORMAL SERVICE
18,000 MILE (29,000 KM)18 MONTH NORMAL SERVICE
\
\
\
\
\
\
\
 
VERIFY 

\b\
\
\
\
\
\
\



Last Major Service Was Performed. 

\
\
\
\
\
\
\



INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


  Brake Hoses 


\
\
\
\
\
\
\


 Engine Coolant Level, Hoses & Clamps 


\
\
\
\
\
\
\


 Brake Linings 


\
\
\
\
\
\
\


 Drive Belts 

\
\
\
\
\
\
\



SERVICE 

\b\
\
\
\
\
\
\


 Rotate Tires 


\
\
\
\
\
\
\


 Lubricate Steering Linkage 

\
\
\
\
\
\
\



REPLACE 

\b\
\
\
\
\
\
\


 Engine Oil 


\
\
\
\
\
\
\


 Engine Oil Filter 

\
\
\
\
\
\
\



LUBRICATION SPECIFICATIONS 

\
\b\
\
\
\b\
\
\



Material  Condition  Specification 

\

\
\
\

\
\
\


Engine Oil Ambient Temperature Above 10F SAE 15W-40 

(
1)  (-12C) To Over 30F (-1C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 10W-30 

0F (-18C) To Over 30F(-1C) 


\
\
\

\
\


Ambient Temperature Less Than  With Block Heater: 

-10F(-23C) Up To 0F (-18C) SAE 10W-30 

  Without Block Heater: 

  SAE 5W-30 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred. Use only API approved 

oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


24,000 MILE (38,000 KM)/24 MONTH NORMAL SERVICE
24,000 MILE (38,000 KM)/24 MONTH NORMAL SERVICE
\
\
\
\
\
\
\
 
VERIFY 

\b\
\
\
\
\
\
\



Last Major Service Was Performed. 

\
\
\
\
\
\
\



INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


 Brake Hoses 


\
\
\
\
\
\
\


 Engine Coolant Level, Hoses & Clamps 


\
\
\
\
\
\
\


 Front Wheel Bearings (4x2) 


\
\
\
\
\
\
\


 Pump Weep Hole For Blockage 


\
\
\
\
\
\
\


 Fan Hub 


\
\
\
\
\
\
\


 Damper 

\
\
\
\
\
\
\



SERVICE 

\b\
\
\
\
\
\
\


 Rotate Tires 


\
\
\
\
\
\
\


 Lubricate Steering Linkage 


\
\
\
\
\
\
\


 Automatic Transmission Bands 


\
\
\
\
\
\
\


 Clean Fuel Strainer 


\
\
\
\
\
\
\


 Adjust Valve Lash Clearance 

\
\
\
\
\
\
\



REPLACE 

\b\
\
\
\
\
\
\


 Engine Oil 


\
\
\
\
\
\
\


 Engine Oil Filter 


\
\
\
\
\
\
\


 Fuel Filter 


\
\
\
\
\
\
\


 Automatic Transmission Fluid & Filter 

\
\
\
\
\
\
\



LUBRICATION SPECIFICATIONS 

\
\b\
\
\
\b\
\
\



Material  Condition  Specification 

\

\
\
\

\
\
\


Engine Oil Ambient Temperature Above 10F SAE 15W-40 

(
1)  (-12C) To Over 30F (-1C)  


\
\
\

\
\


Ambient Temperature Less Than  SAE 10W-30 

0F (-18C) To Over 30F(-1C) 


\
\
\

\
\


Ambient Temperature Less Than  With Block Heater: 

-10F(-23C) Up To 0F (-18C) SAE 10W-30 

  Without Block Heater: 

  SAE 5W-30 

\

\
\
\

\
\
\


Engine  All  50/50 Mixture Of 

 Coolant   Distilled Water & 

  Ethylene Glycol 

\

\
\
\

\
\
\


Brake Fluid  All  DOT 3 

\

\
\
\

\
\
\


Steering  All  Mopar Multi-Mileage 

Linkage   Lubricant 

Lubricant   

\

\
\
\

\
\
\


Automatic  All  ATF+2 Type 7176 

Transmission   

Fluid   

\

\
\
\

\
\
\


Wheel Bearing All High Temperature Multi-

Grease   -Purporse EP Grease 

\
\
\
\
\
\
\


(
1) - SAE 10W-30 engine oil is preferred. Use only API approved 

oil with Starburst Symbol. 

\
\
\
\
\
\
\



FLUID CAPACITIES 

\
\b\
\
\
\b\
\
\



Item  Condition  Specification (1) 

\

\
\
\

\
\
\


Engine Oil  Capacity, Upper Safe Mark  10 Qts. (9.5L) 


\
\
\

\
\


 Capacity, Lower Safe Mark  8 Qts. (7.5L) 

\

\
\
\

\
\
\


Engine  Drained  26 Qts. (24.5L) 

Coolant   

\

\
\
\

\
\
\


Automatic  46RE: Dry Fill  17 Qts. (16L) 

Transmission 
\
\
\

\
\


Fluid  47RE: Dry Fill  17 Qts. (16L) 

\
\
\
\
\
\
\


(
1) - Capacities are recommended or calculated levels. Always use 

dipstick (if available) to measure level. 
\f
\
\
\
\
\
\
\


30,000 MILE (48,000 KM)/30 MONTH NORMAL SERVICE
30,000 MILE (48,000 KM)/30 MONTH NORMAL SERVICE
\
\
\
\
\
\
\
 
VERIFY 

\b\
\
\
\
\
\
\



Last Major Service Was Performed. 

\
\
\
\
\
\
\



INSPECT 

\b\
\
\
\
\
\
\


 Exhaust System 


\
\
\
\
\
\
\


 Brake Hoses 


\
\
\
\
\
\
\


 Engine Coolant Level, Hoses & Clamps 

\
\
\
\
\
\
\



SERVICE 

\b\
\
\
\
\
\
\


 Rotate Tires 


\
\
\
\
\
\
\


 Lubricate Steering Linkage 

\
\
\
\
\
\
\



REPLACE 

\b\
\
\
\
\
\
\