coolant capacity DODGE RAM 1999 Service Repair Manual
Page 627 of 1691
COOLING SYSTEM BLEEDING
GASOLINE ENGINES
Air in system will collect under radiator cap. As engine
reaches operating temperature, coolant and any trapped air will enter
reserve tank. As engine cools, a vacuum will be created which will
draw only coolant into cooling system. After engine has gone through a
warm-up and cooling cycle, run engine until it again reaches operating
temperature. Ensure coolant in reserve tank is at warm coolant mark on
reserve tank or dipstick.
5.9L DIESEL ENGINE
For bleeding procedures on 5.9L diesel, see appropriate 12-
valve or 24-valve engine article in ENGINES. DO NOT operate engine
while filling cooling system.
SPECIFICATIONS
COOLING SYSTEM SPECIFICATIONS
COOLING SYSTEM SPECIFICATIONS - CARS \
\
\
\
\
\
\
Application Specification
Avenger & Sebring Coupe
Coolant Replacement Interval ........... 30,000 Miles Or 24 Months
Coolant Capacity ................................. 7.4 Qts. (7.0L)\
Pressure Cap .............................................. 16 psi
Thermostat
DOHC
Starts To Open ................................... 195
F (91C)
Fully Opens ..................................... 216F (102C)
SOHC
Starts To Open ................................... 180
F (82C)
Fully Opens ...................................... 203F (95C)
Breeze, Cirrus, Sebring Convertible & Stratus
Coolant Replacement Interval ........... 45,000 Miles Or 36 Months
Coolant Capacity
2.0L ............................................ 8.5 Qts. (8.0L)\
2.4L ............................................ 9.0 Qts. (8.5L)\
2.5L .......................................... 10.5 Qts. (10.0L)\
Pressure Cap ........................................... 14-18 psi
Thermostat
Starts To Open .............................. 192-199
F (88-93C)
Fully Opens ....................................... 220F (104C)
Concorde, Intrepid, LHS & 300M
Coolant Replacement Interval ....................... 120,000 Miles
Coolant Capacity ................................. 9.4 Qts. (8.9L)\
Pressure Cap ........................................... 14-18 psi
Thermostat
Starts To Open .............................. 192-199
F (88-93C)
Fully Opens ....................................... 220F (104C)
Neon
Coolant Replacement Interval ........... 45,000 Miles Or 36 Months
Coolant Capacity ................................. 7.4 Qts. (7.0L)\
Pressure Cap ........................................... 14-18 psi
Thermostat
Starts To Open .............................. 192-199
F (88-93C)
Fully Opens ....................................... 220F (104C)
Page 628 of 1691
Talon
Coolant Replacement Interval ........... 30,000 Miles Or 24 Months
Coolant Capacity ................................. 7.4 Qts. (7.0L)\
Pressure Cap
VIN F ................................................. 11-15 psi
VIN Y ................................................. 14-18 psi
Thermostat
Starts To Open
VIN F ............................................ 180
F (82C)
VIN Y ............................................ 195F (91C)
Fully Opens
VIN F ............................................ 203
F (95C)
VIN Y ........................................... 216F (102C) \
\
\
\
\
\
\
COOLING SYSTEM SPECIFICATIONS - TRUCKS \
\
\
\
\
\
\
Application Specification
Coolant Replacement Interval ............. 45,000 Miles Or 36 Months
Coolant Capacity ( 1)
Caravan, Town & Country, & Voyager
2.4L ...................................... ( 2) 11.2 Qts. (10.6L)
3.0L ...................................... ( 2) 13.0 Qts. (12.3L)
3.3L & 3.8L ............................... ( 2) 13.2 Qts. (12.5L)
Dakota
2.5L ............................................ 9.8 Qts. (9.3L)\
3.9L .......................................... 14.0 Qts. (13.2L)\
5.2L .......................................... 14.3 Qts. (13.5L)\
5.9L ................................................. 14.6L (13.7L)\
Durango
3.9L .......................................... 14.0 Qts. (13.2L)\
5.2L & 5.9L ...................................... 14.3 Qts. (13.5L)\
Ram Pickup
3.9L, 5.2L & 5.9L (Gasoline) .................. 20.0 Qts. (18.9L\
)
5.9L (Diesel) ................................. 24.0 Qts. (22.7L\
)
8.0L .......................................... 26.0 Qts. (24.6L)\
Ram Van/Wagon
3.9L ........................................... 10.4 Qts. (9.8L)\
5.2L .......................................... 13.1 Qts. (12.4L)\
5.9L
With Rear Heater ............................ 14.1 Qts. (13.3L)\
Without Rear Heater ......................... 13.1 Qts. (12.4L)\
Pressure Cap ............................................. 14-16 psi
Thermostat
Diesel Engines
Starts To Open ..................................... 181
F (83C)
Fully Open ............................................ 203F (95C)
Gasoline Engines
Starts To Open ..................................... 192
F (89C)
Fully Opens ....................................... 220F (104C)
( 1) - Capacities listed are approximate.
( 2) - Capacity includes heater and coolant recovery tank. Add 2 qts.
(1.9L) for models equipped with rear heater.
\
\
\
\
\
\
\
Page 888 of 1691
(
1) - SAE 10W-30 engine oil is preferred for use in all Dodge
trucks. Use only API approved oil with Starburst Symbol.
(
2) - Axles with Limited-Slip Differentials require the use of
a 5% Friction Modifier, such as Mopar Gear Oil Additive
Friction Modifier.
(
3) - Never add gear oil, automatic transmission fluid or
hydroboost power steering fluid.
\
\
\
\
\
\
\
FLUID CAPACITIES - DIESEL
FLUID CAPACITIES TABLE - DIESEL \
\
\
\
\
\
\
Item Condition Specification (1)
\
\
\
\
\
\
\
\f
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
\
\f
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
\f
Engine Drained 26 Qts. (24.5L)
Coolant
\
\
\
\
\
\
\
\f
Automatic 46RE: Dry Fill 17 Qts. (16L)
Transmission
\
\
\
\
\
\
\f
Fluid 47RE: Dry Fill 17 Qts. (16L)
\
\
\
\
\
\
\
\f
Manual NV4500 4 Qts. (3.8L)
Transmission
Fluid
\
\
\
\
\
\
\
\f
Rear Axle DANA 70 Model 267 (2WD) 7 Pts. (3.3L)
Lubricant
\
\
\
\
\
\
\f
DANA 70 Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
\
\f
DANA 80 Model 286 (2WD) 6.8.Pts. (3.2L)
\
\
\
\
\
\
\f
DANA 80 Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
\f
Rear Axle Model 267 (2WD) 7 Pts. (3.3L)
Limited Slip
\
\
\
\
\
\
\f
Differential Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
\
\f
Model 286 (2WD) 6.8 Pts. (3.2L)
\
\
\
\
\
\
\f
Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
\f
Front Axle Model 248 7.6 Pts. (3.6L)
Lubricant
\
\
\
\
\
\
\
\f
Transfer Case NV241 HD 6.5 Pts. (3.1L)
Fluid
\
\
\
\
\
\
\
\f
Power Take NV021 4.6 Pts. (2.1L)
Off Adapter
\
\
\
\
\
\
\
\f
Power Drained 2.7 Pts. (1.3L)
Steering
Fluid
\
\
\
\
\
\
\
\f
A/C Charge Capacity 32 Oz. (.9Kg)
Refrigerant
Page 889 of 1691
\
\
\
\
\
\
\
\f
Refrigerant A/C System Capacity 7.75 Oz. (230ML)
Oil
\
\
\
\
\
\
\
\f
Fuel Tank Capacity 35 Gal. (132L)
\
\
\
\
\
\
\
\f
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS - GAS
LUBRICATION SPECIFICATIONS TABLE - GAS \
\
\
\
\
\
\
Material Condition Specification
\
\
\
\
\
\
\
\f
Engine Oil Ambient Temperature Above 0 \bF SAE 10W-30
(
1) (-18\bC) To Over 100\bF (38\bC)
\
\
\
\
\
\
\f
Ambient Temperature Less Than SAE 5W-30
-20\bF (-29\bC) Up To 32\bF (0\bC)
\
\
\
\
\
\
\
\f
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
\f
Brake Fluid All DOT 3
\
\
\
\
\
\
\
\f
Automatic All ATF+2 Type 7176
Transmission
Fluid
\
\
\
\
\
\
\
\f
Transfer Case All ATF+2 Type 7176
Fluid Or DEXRON III ATF
\
\
\
\
\
\
\
\f
Manual NV-4500 75W-90 Synthc. API GL4
Transmission
\
\
\
\
\
\
\f
Fluid NV-3500 Mopar Manual
Transmission Fluid
\
\
\
\
\
\
\
\f
Steering All Mopar Multi-Mileage
Linkage Lubricant
Lubricant
\
\
\
\
\
\
\
\f
Wheel Bearing All High Temperature Multi-
Grease -Purporse EP Grease
\
\
\
\
\
\
\
\f
Rear Axle & All Mopar Hypoid Lubricant
4x4 Frt. Axle SAE 80W-90
Lubricant (
2) GL-5 Gear Lube
\
\
\
\
\
\
\
\f
Power All Mopar Power Steering
Steering Fluid Or Equivalant
Fluid (
3) Petroleum Based
\
\
\
\
\
\
\
\f
Clutch All Multipurpose Grease
Linkage NLGI Grade 2 E.P.
Lubricant
\
\
\
\
\
\
\
\f
A/C All R-134a
Page 1000 of 1691
Engine Oil Ambient Temperature Above 10 F SAE 15W-40
(
1) (-12 C) To Over 30 F (-1 C)
\
\
\
\
\
Ambient Temperature Less Than SAE 10W-30
0 F (-18 C) To Over 30 F(-1 C)
\
\
\
\
\
Ambient Temperature Less Than With Block Heater:
-10 F(-23 C) Up To 0 F (-18 C) SAE 10W-30
Without Block Heater:
SAE 5W-30
\
\
\
\
\
\
\
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
Brake Fluid All DOT 3
\
\
\
\
\
\
\
Steering All Mopar Multi-Mileage
Linkage Lubricant
Lubricant
\
\
\
\
\
\
\
(
1) - SAE 10W-30 engine oil is preferred for use in all Dodge
trucks. Use only API approved oil with Starburst Symbol.
\
\
\
\
\
\
\
FLUID CAPACITIES
\
\b\
\
\
\b\
\
\
Item Condition Specification (1)
\
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
Engine Drained 26 Qts. (24.5L)
Coolant
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\f
\
\
\
\
\
\
\
12,000 MILE (19,000 KM)/12 MONTH NORMAL SERVICE
12,000 MILE (19,000 KM)/12 NORMAL SERVICE\
\
\
\
\
\
\
INSPECT
\b\
\
\
\
\
\
\
Exhaust System
\
\
\
\
\
\
\
Brake Hoses
\
\
\
\
\
\
\
Engine Coolant Level, Hoses & Clamps
\
\
\
\
\
\
\
Water Pump Weep Hole For Blockage
\
\
\
\
\
\
\
SERVICE
\b\
\
\
\
\
\
\
Rotate Tires
\
\
\
\
\
\
\
Lubricate Steering Linkage
\
\
\
\
\
\
\
Clean Fuel Strainer
\
\
\
\
\
\
\
REPLACE
Page 1001 of 1691
\b\
\
\
\
\
\
\
Engine Oil
\
\
\
\
\
\
\
Engine Oil Filter
\
\
\
\
\
\
\
Fuel Filter
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\
\b\
\
\
\b\
\
\
Material Condition Specification
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Above 10 F SAE 15W-40
(
1) (-12 C) To Over 30 F (-1 C)
\
\
\
\
\
Ambient Temperature Less Than SAE 10W-30
0 F (-18 C) To Over 30 F(-1 C)
\
\
\
\
\
Ambient Temperature Less Than With Block Heater:
-10 F(-23 C) Up To 0 F (-18 C) SAE 10W-30
Without Block Heater:
SAE 5W-30
\
\
\
\
\
\
\
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
Brake Fluid All DOT 3
\
\
\
\
\
\
\
Steering All Mopar Multi-Mileage
Linkage Lubricant
Lubricant
\
\
\
\
\
\
\
(
1) - SAE 10W-30 engine oil is preferred. Use only API approved
oil with Starburst Symbol.
\
\
\
\
\
\
\
FLUID CAPACITIES
\
\b\
\
\
\b\
\
\
Item Condition Specification (1)
\
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
Engine Drained 26 Qts. (24.5L)
Coolant
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\f
\
\
\
\
\
\
\
18,000 MILE (29,000 KM)/18 MONTH NORMAL SERVICE
18,000 MILE (29,000 KM)18 MONTH NORMAL SERVICE\
\
\
\
\
\
\
VERIFY
\b\
\
\
\
\
\
\
Last Major Service Was Performed.
\
\
\
\
\
\
\
INSPECT
\b\
\
\
\
\
\
\
Exhaust System
\
\
\
\
\
\
\
Page 1002 of 1691
Brake Hoses
\
\
\
\
\
\
\
Engine Coolant Level, Hoses & Clamps
\
\
\
\
\
\
\
Brake Linings
\
\
\
\
\
\
\
Drive Belts
\
\
\
\
\
\
\
SERVICE
\b\
\
\
\
\
\
\
Rotate Tires
\
\
\
\
\
\
\
Lubricate Steering Linkage
\
\
\
\
\
\
\
REPLACE
\b\
\
\
\
\
\
\
Engine Oil
\
\
\
\
\
\
\
Engine Oil Filter
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\
\b\
\
\
\b\
\
\
Material Condition Specification
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Above 10 F SAE 15W-40
(
1) (-12 C) To Over 30 F (-1 C)
\
\
\
\
\
Ambient Temperature Less Than SAE 10W-30
0 F (-18 C) To Over 30 F(-1 C)
\
\
\
\
\
Ambient Temperature Less Than With Block Heater:
-10 F(-23 C) Up To 0 F (-18 C) SAE 10W-30
Without Block Heater:
SAE 5W-30
\
\
\
\
\
\
\
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
Brake Fluid All DOT 3
\
\
\
\
\
\
\
Steering All Mopar Multi-Mileage
Linkage Lubricant
Lubricant
\
\
\
\
\
\
\
(
1) - SAE 10W-30 engine oil is preferred. Use only API approved
oil with Starburst Symbol.
\
\
\
\
\
\
\
FLUID CAPACITIES
\
\b\
\
\
\b\
\
\
Item Condition Specification (1)
\
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
Engine Drained 26 Qts. (24.5L)
Coolant
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\f
\
\
\
\
\
\
\
Page 1004 of 1691
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
Brake Fluid All DOT 3
\
\
\
\
\
\
\
Steering All Mopar Multi-Mileage
Linkage Lubricant
Lubricant
\
\
\
\
\
\
\
Automatic All ATF+2 Type 7176
Transmission
Fluid
\
\
\
\
\
\
\
Wheel Bearing All High Temperature Multi-
Grease -Purporse EP Grease
\
\
\
\
\
\
\
(
1) - SAE 10W-30 engine oil is preferred. Use only API approved
oil with Starburst Symbol.
\
\
\
\
\
\
\
FLUID CAPACITIES
\
\b\
\
\
\b\
\
\
Item Condition Specification (1)
\
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
Engine Drained 26 Qts. (24.5L)
Coolant
\
\
\
\
\
\
\
Automatic 46RE: Dry Fill 17 Qts. (16L)
Transmission
\
\
\
\
\
Fluid 47RE: Dry Fill 17 Qts. (16L)
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\f
\
\
\
\
\
\
\
30,000 MILE (48,000 KM)/30 MONTH NORMAL SERVICE
30,000 MILE (48,000 KM)/30 MONTH NORMAL SERVICE\
\
\
\
\
\
\
VERIFY
\b\
\
\
\
\
\
\
Last Major Service Was Performed.
\
\
\
\
\
\
\
INSPECT
\b\
\
\
\
\
\
\
Exhaust System
\
\
\
\
\
\
\
Brake Hoses
\
\
\
\
\
\
\
Engine Coolant Level, Hoses & Clamps
\
\
\
\
\
\
\
SERVICE
\b\
\
\
\
\
\
\
Rotate Tires
\
\
\
\
\
\
\
Lubricate Steering Linkage
\
\
\
\
\
\
\
REPLACE
\b\
\
\
\
\
\
\
Page 1005 of 1691
Engine Oil
\
\
\
\
\
\
\
Engine Oil Filter
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\
\b\
\
\
\b\
\
\
Material Condition Specification
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Above 10 F SAE 15W-40
(
1) (-12 C) To Over 30 F (-1 C)
\
\
\
\
\
Ambient Temperature Less Than SAE 10W-30
0 F (-18 C) To Over 30 F(-1 C)
\
\
\
\
\
Ambient Temperature Less Than With Block Heater:
-10 F(-23 C) Up To 0 F (-18 C) SAE 10W-30
Without Block Heater:
SAE 5W-30
\
\
\
\
\
\
\
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
Brake Fluid All DOT 3
\
\
\
\
\
\
\
Steering All Mopar Multi-Mileage
Linkage Lubricant
Lubricant
\
\
\
\
\
\
\
(
1) - SAE 10W-30 engine oil is preferred. Use only API approved
oil with Starburst Symbol.
\
\
\
\
\
\
\
FLUID CAPACITIES
\
\b\
\
\
\b\
\
\
Item Condition Specification (1)
\
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
Engine Drained 26 Qts. (24.5L)
Coolant
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\f
\
\
\
\
\
\
\
36,000 MILE (58,000 KM)/36 MONTH NORMAL SERVICE
36,000 MILE (58,000 KM)/36 MONTH NORMAL SERVICE\
\
\
\
\
\
\
VERIFY
\b\
\
\
\
\
\
\
Last Major Service Was Performed.
\
\
\
\
\
\
\
INSPECT
\b\
\
\
\
\
\
\
Exhaust System
\
\
\
\
\
\
\
Brake Hoses
\
\
\
\
\
\
\
Brake Linings
Page 1006 of 1691
\
\
\
\
\
\
\
Drive Belts
\
\
\
\
\
\
\
Water Pump Weep Hole For Blockage
\
\
\
\
\
\
\
SERVICE
\b\
\
\
\
\
\
\
Rotate Tires
\
\
\
\
\
\
\
Lubricate Steering Linkage
\
\
\
\
\
\
\
Clean Fuel Strainer
\
\
\
\
\
\
\
REPLACE
\b\
\
\
\
\
\
\
Engine Oil
\
\
\
\
\
\
\
Engine Oil Filter
\
\
\
\
\
\
\
Engine Coolant
\
\
\
\
\
\
\
Fuel Filter
\
\
\
\
\
\
\
Transfer Case Fluid
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\
\b\
\
\
\b\
\
\
Material Condition Specification
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Above 10 F SAE 15W-40
(
1) (-12 C) To Over 30 F (-1 C)
\
\
\
\
\
Ambient Temperature Less Than SAE 10W-30
0 F (-18 C) To Over 30 F(-1 C)
\
\
\
\
\
Ambient Temperature Less Than With Block Heater:
-10 F(-23 C) Up To 0 F (-18 C) SAE 10W-30
Without Block Heater:
SAE 5W-30
\
\
\
\
\
\
\
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
Brake Fluid All DOT 3
\
\
\
\
\
\
\
Steering All Mopar Multi-Mileage
Linkage Lubricant
Lubricant
\
\
\
\
\
\
\
Transfer Case All ATF+2 Type 7176
Fluid Or DEXRON III ATF
\
\
\
\
\
\
\
(
1) - SAE 10W-30 engine oil is preferred. Use only API approved
oil with Starburst Symbol.
\
\
\
\
\
\
\
FLUID CAPACITIES
\
\b\
\
\
\b\
\
\
Item Condition Specification (1)
\
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
Capacity, Lower Safe Mark 8 Qts. (7.5L)